3D-printing-assisted fabrication of chitosan scaffolds from different sources and cross-linkers for dental tissue engineering.

The aim of the present study was to fabricate and characterise chitosan scaffolds from animal and fungal sources, with or without gelatine as a co-polymer, and cross-linked to 3-glycidyloxyproply trimethoxysilane (GPTMS) or genipin for application in dental root tissue engineering. Chitosan-based scaffolds were prepared by the emulsion freeze-drying technique. Scanning electron microscopy (SEM) and nano-focus computed tomography (nano-CT) were used to characterise scaffold microstructure. Chemical composition and cross-linking were evaluated by Fourier transform infrared-attenuated total reflectance spectroscopy. Compression tests were performed to evaluate scaffold mechanical properties. Scaffold degradation was evaluated by gravimetric method and SEM. Scaffold bioactivity immersed in simulated body fluid was evaluated by SEM, with associated electron dispersive X-ray spectroscopy, and apatite formation was examined by X-ray diffraction. Finally, human dental pulp stem cells (hDPSCs) viability was evaluated. The fabrication method used was successful in producing scaffolds with organised porosity. Chitosan source (animal vs. fungal), co-polymerisation with gelatine and cross-linking using GPTMS or genipin had a significant effect on scaffold properties and hDPSCs response. Chitosan-genipin (CS-GEN) scaffolds had the largest pore diameter, while the chitosan-gelatine-GPTMS (CS-GEL-GPTMS) scaffolds had the smallest. Animal chitosan-gelatine co-polymerisation increased scaffold compressive strength, while fungal chitosan scaffolds (fCS-GEL-GPTMS) had the fastest degradation rate, losing 80 % of their weight by day 21. Gelatine co-polymerisation and GPTMS cross-linking enhanced chitosan scaffolds bioactivity through the formation of an apatite layer as well as improved hDPSCs attachment and viability. Tailored chitosan scaffolds with tuned properties and favourable hDPSCs response can be obtained for regenerative dentistry applications.

Mirror, mirror on the wall: the face of HIV + women in Europe today.

Sexual and reproductive health (SRH) and rights are important components of quality of life. This cross-sectional study describes HIV-positive women's SRH aspirations and needs and the predictive value of selected SRH factors on condom use with steady sexual partners. Data were collected in a European multi-centre study in 17 HIV centres in 14 European countries by a standardised anonymous self-administered questionnaire. Descriptive statistics and hierarchical regression analysis were carried out and qualitative data from related formative research illustrated the findings. Among 387 HIV-positive women, 57% had children and 35% had become pregnant since their HIV-diagnosis. Contraceptive needs were largely unmet: 14% had undergone a pregnancy termination. About 83% changed their sexual behaviour after HIV-diagnosis in some ways. Sixty-two percent had at least one sexual encounter with a steady partner during the past six months and 51% used condoms consistently. Significant correlations with condom use were identified for childbearing since HIV-diagnosis (r=-0.21, p<0.01), miscarriage since HIV-diagnosis (r=-0.24, p<0.01), the use of contraception (r=0.47, p<0.001) and changes in sexual behaviour after HIV-diagnosis (r=0.20, p<0.01). Hierarchical regression analysis controlled for education, migration background, age, undetectable viral load and partners' serostatus. The following significant predictors for condom use were established: the use of contraceptives (beta=0.33, p<0.001); miscarriage since HIV-diagnosis (beta=-0.16, p<0.01); childbearing since HIV-diagnosis (beta=-0.12, p<0.05); and having an HIV-positive partner (beta=-0.13, p<0.05). For study population, consistent condom use performed a challenge. Selected SRH-issues predicted condom use. Sexual risk reduction and positive prevention should be discussed in the context of family planning and integrate SRH perspectives in routine HIV care.

Electron tomography on micrometer-thick specimens with nanometer resolution.

Transmission electron microscopy (TEM) is a well-established technique to explore matter down to the atomic scale. TEM tomography methods have been developed to obtain volume information at the mesoscopic dimensions of devices or complex mixtures of multiphase objects with nanometer resolution, but these methods are in general only applicable to relatively thin specimens with a few hundred nanometer thickness at most. Here we introduce an approach based on scanning TEM (STEM) tomography that pushes the resolution in three dimensions down to a few nanometers for several micrometer ultrathick specimens using a conventional TEM with 300 kV accelerating voltage, and we demonstrate its versatility for materials research and nanotechnology.

Phonon affected transport through molecular quantum dots.

To describe the interaction of molecular vibrations with electrons at a quantum dot contacted to metallic leads, we extend an analytical approach that we previously developed for the many-polaron problem. Our scheme is based on an incomplete variational Lang-Firsov transformation, combined with a perturbative calculation of the electron-phonon self-energy in the framework of generalized Matsubara functions. This allows us to describe the system at weak-to-strong coupling and intermediate-to-large phonon frequencies. We present results for the quantum dot spectral function and for the kinetic coefficient that characterizes the electron transport through the dot. With these results we critically examine the strengths and limitations of our approach, and discuss the properties of the molecular quantum dot in the context of polaron physics. We place particular emphasis on the importance of corrections to the concept of an anti-adiabatic dot polaron suggested by the complete Lang-Firsov transformation.

Investigation on stick phenomena in metal-on-metal hip joints after resting periods.

Insufficient understanding of tribological behaviour in total joint arthroplasty is considered as one of the reasons for prosthesis failure. Contrary to the continuous motion input profiles of hip simulators, human locomotion contains motion interruptions. These occurring resting periods can cause stick phenomena in metal-on-metal hip joints. The aim of the present study was to investigate the tribological sensitivity of all-metal bearings to motion interruptions on in vitro test specimens and retrieved implants. Friction and wear with and without resting periods were quantified. Unlike the metal-on-polyethylene joints, the static friction of metal-on-metal joints increased up to micros = 0.3 with rest, while wear appeared to be unaffected. This effect is caused by the interlocking of firmly adhered carbon layers, which were generated from the protein-containing lubricant through tribochemical reactions. Since more than 80 per cent of the retrieved implants exhibited macroscopically visible carbon layers, the increase in friction presumably also occurs under physiological conditions, which is then transferred to the bone-implant interface. These recurrent tangential stress peaks should be considered for the design features of the cup-bone interface, in particular when larger-sized implant heads are used.

Nanoscale electrical characterization of semiconducting polymer blends by conductive atomic force microscopy (C-AFM).

For the first time local electrical characteristics of a blend of two semiconducting polymers were studied with conductive atomic force microscopy (C-AFM). The investigated mixture is potentially interesting as the active layer in plastic photovoltaic devices. Besides conventional topography analysis of morphology and phase separation, the internal structure of the active layer was investigated by observing the current distribution with nanoscale spatial resolution. Similar to force spectroscopy, current imaging spectroscopy was performed during scanning the sample surface. Different types of current-voltage (I-V) characteristics were extracted from the array of spectroscopic data obtained from each point of the scans, and local heterogeneities of the electric characteristic were determined and discussed.

Gas-phase properties and fragmentation behavior of cationic, dinuclear iron chloride clusters Fe(2)Cl(n)()(+) (n = 1-6).

Sector-field mass spectrometry is used to probe the fragmentation patterns of cationic dinuclear iron chloride clusters Fe(2)Cl(n)()(+) (n = 1-6). For the chlorine-rich, high-valent Fe(2)Cl(n)()(+) ions (n = 4-6), losses of atomic and molecular chlorine prevail in the unimolecular and collision-induced dissociation patterns. Instead, the chlorine deficient, formally low-valent Fe(2)Cl(n)()(+) clusters (n = 1-3) preferentially undergo unimolecular degradation to mononuclear FeCl(m)()(+) ions. In addition, photoionization is used to determine IE(Fe(2)Cl(6)) = 10.85 +/- 0.05 eV along with appearance energy measurements for the production of Fe(2)Cl(5)(+) and Fe(2)Cl(4)(+) cations from iron(III) chloride vapor. The combination of the experimental results allows an evaluation of some of the thermochemical properties of the dinuclear Fe(2)Cl(n)()(+) cations: e.g., Delta(f)H(Fe(2)Cl(+)) = 232 +/- 15 kcal/mol, Delta(f)H(Fe(2)Cl(2)(+)) = 167 +/- 4 kcal/mol, Delta(f)H(Fe(2)Cl(3)(+)) = 139 +/- 4 kcal/mol, Delta(f)H(Fe(2)Cl(4)(+)) = 113 +/- 4 kcal/mol, Delta(f)H(Fe(2)Cl(5)(+)) = 79 +/- 5 kcal/mol, and Delta(f)H(Fe(2)Cl(6)(+)) = 93 +/- 2 kcal/mol. The analysis of the data suggests that structural effects are more important than the formal valency of iron as far as the Fe-Cl bond strengths in the Fe(2)Cl(n)()(+) ions are concerned.

Low leukocyte contamination without filtration by preparation of platelet concentrates in cylindrical bags with the buffy-coat method.

BACKGROUND AND OBJECTIVES: The buffy-coat (BC) method for platelet concentrate (PC) preparation was modified in order to obtain leukodepleted PCs from single BCs without filtration. MATERIALS AND METHODS: BCs were centrifuged in cylindrical BC bags and the optimal centrifugation conditions and optimal hematocrit were determined. RESULTS: With optimal conditions, a tenfold lower leukocyte contamination was obtained compared with the conventionally shaped, wide BC bag (0.3 +/- 0.19 versus 3.0 +/- 1.71 x 10(6) leukocytes per unit; 85-ml BCs). The platelet yield obtained with the cylindrical bag did not differ significantly from the yield obtained with the conventional bag (56 +/- 16.4 versus 61 +/- 15 x 10(9) platelets per PC). Furthermore, when PCs were prepared from 100-ml BCs in cylindrical bags, a leukocyte contamination of 0.2 +/- 0.11 x 10(6) and a platelet content of 61 +/- 13.5 x 10(9) per PC were obtained. CONCLUSION: The use of cylindrical BC bags reduced the leukocyte contamination in PCs to a level required for leuko-depletion without affecting platelet recovery.

A striated pattern of wear in ultrahigh-molecular-weight polyethylene components of Miller-Galante total knee arthroplasty.

Wear of the polyethylene tibial components is a potential cause of failure in total knee arthroplasty. In addition to pitting, burnishing, and scratching, subtle striations on the bearing portion of the tibial surface have been observed in components retrieved relatively early after implantation. The striated pattern most typically occurred in areas centrally located within the articulating surface. The striations were anteroposterior directed and were identified as local cold flow at the surface. There was a strong correlation between the medial and lateral striated areas, suggesting that these patterns are related to cyclic rolling of the knee. The general characteristics and alignment of the striations could be attributed to the compressive and tractive forces occurring during femoral rollback. For the clinician, these results suggest that kinematics, as well as contact stress, should be considered when evaluating wear of polyethylene components.

Long-term in vivo alterations of polyester vascular grafts in humans.

OBJECTIVES: To examine the influence of in vivo hydrolysis on the physical properties of polyester grafts and their correlation to the period of implantation in the human body. MATERIALS AND METHODS: Sixty-five explanted vascular grafts were obtained after 0-23 years of implantation due to suture aneurysms (18), occlusion (12), graft infection (12), failure of graft material (7) and post-mortem (16). The surface was examined by scanning electron microscopy, the molecular integrity by infra-red spectroscopy and physical strength by probe puncture. RESULTS: Scission of macromolecular chains and loss of strength were shown. It was demonstrated that hydrolytic degradation of polyester takes place with increasing time of implantation in humans. Analysis by linear regression showed that polyester grafts lose 31.4% of their bursting strength in 10 years and 100% in 25-39 years after implantation. CONCLUSIONS: Regular follow-ups of patients with aged vascular grafts and the precise documentation of implanted materials are necessary to estimate graft degradation.

Pooled platelet concentrates prepared by the platelet-rich-plasma method and filtered with three different filters and stored for 8 days.

Pooled platelet concentrates (PC) prepared by the platelet-rich plasma (PRP) method were filtered with three different filters and stored for 8 days at room temperature. The effect of filtration on leukocyte contamination, platelet concentration, and the in vitro function, morphology, metabolism and activation of platelets were studied. Eight pools of 20 PRP-PC were used, each pool was split into 4 equal volumes; 3 were filtered over a PL50HF, a PL-10A and a Bio P10 filter, the 4 served as a control. After filtration, leukocyte counts exceeded 3 x 10(5) in none of the pooled PC. Platelet loss induced by filtration was about 17%. During storage, no differences in pH, PCO2, and lactate and glucose concentration were found between the filtered and the unfiltered units, nor were any differences observed between filtered and unfiltered pooled PC in aggregation upon stimulation with collagen and/or ADP, adhesion capacity to collagen in flowing blood, nucleotide content of the platelets and nucleobase concentration in the plasma, expression of activation-dependent antigens, or platelet morphology as observed by light microscopy and by the swirling effect. Selective removal of beta-thromboglobulin (22%) by the PL50HF filter was observed. Pooled PC prepared by the PRP-method can be filtered and stored for 8 days without detrimental effect on platelet function, metabolism or activation.

In vitro evaluation of platelet concentrates, prepared from pooled buffy coats, stored for 8 days after filtration.

BACKGROUND: Posttransfusion complications can be prevented by pretransfusion removal of donor white cells from platelet concentrate. The filtration used for this removal seems to have little effect on platelet function and activation, but more information is needed on its effect on function during subsequent long-term storage of concentrate. STUDY DESIGN AND METHODS: The effect of prestorage filtration of buffy coat-prepared platelet concentrates (PCs) on platelet function, metabolism, and activation was investigated. A pool of three PCs, each made of four buffy coats, was split into three equal volumes; two were filtered over two different filters and the third served as a control. Variables monitored immediately after filtration and during the subsequent 8-day storage period at 22 degrees C included aggregation upon stimulation with collagen and/or ADP, platelet adhesion capacity to collagen and fibrinogen in flowing blood, nucleotide content of and nucleobase release by the platelets, expression of activation-dependent antigens, and beta-thromboglobulin release by the platelets. RESULTS: No differences were observed between the PCs filtered over two different filters and the nonfiltered control PCs immediately after filtration and during storage, except for a selective removal (20%) of beta-thromboglobulin by one filter. CONCLUSION: PCs prepared from a pool of four buffy coats can be filtered and subsequently stored for 8 days (starting +/- 24 hours after whole blood collection) without detriment to platelet function, metabolism, or activation.

Effect of filtration on subsequently stored platelet concentrates.

The effect of filtration on the quality of platelet concentrates (PC) during storage was investigated. Two leukocyte depletion filters (Pall PL50HF and Sepacell PL-10A) were applied to filter PC made from a pool of 4 buffy coats. For each experiment 3 PC were pooled and divided into 3 identical PC to eliminate differences between the PC. Two PC were filtered, and the third PC served as an unfiltered control. A total of 12 experiments was performed. Before filtration, volumes of the PC were 263 +/- 11.7 ml (mean +/- SD). Platelet and leukocyte counts per PC were 241 +/- 25.9 x 10(9) and 7.2 +/- 1.8 x 10(6), respectively. After filtration leukocyte counts did not exceed 5 x 10(4) in any of the PC. In the PC filtered with the Pall PL50HF the mean platelet loss was approximately 14% and with the Sepacell PL-10A, 17%. During a 9-day storage period the pH, PO2, PCO2, bicarbonate, lactate and glucose concentration and LDH release as well as the morphology, examined by the swirling effect and microscopically, were not significantly different in filtered and unfiltered units. Filtration through the 2 investigated leukocyte depletion filters for PC did not adversely affect in vitro viability of the platelets during storage.

Platelets stored for 6 days in a polyolefin container in a synthetic medium with minimal plasma carry-over.

Platelet concentrates (PC) were stored for 6 days in either polyolefin (PO) or polyvinylchloride/di-(2-ethylhexyl)phtalate (PVC/DEHP) bags in 100% plasma or in a synthetic medium with 35 or 10% plasma. For all conditions studied the usual in vitro parameters were well maintained, with a pH above 6.8. In both bag types platelets can be satisfactorily stored for 6 days in a synthetic medium with minimal amounts of residual plasma. For this medium, the PO bag offers a slight advantage with respect to the preservation of platelet ATP content (> 80 versus > 70% in the PVC bags) and aggregation and adhesion capacity. The adhesion capacity increased in the PO bags, while it decreased in the PVC bags.

Effect of pre-incubation at 37 degrees C of platelet concentrates on the post-transfusion platelet adhesion capacity to collagen and fibrinogen.

The effect of warming (37 degrees C) of stored platelet concentrates (PC) on the post-transfusion platelet function as measured by the adhesion capacity in a rectangular perfusion system under flow conditions was analyzed in 22 patients undergoing transfusion for stable thrombocytopenia. Nine patients received a PC stored at 22 degrees C and incubated at 37 degrees C for 1 h before transfusion, 10 patients received a non-warmed PC, 3 patients received both a pre-warmed and a non-warmed PC. In the PC the platelet adhesion capacity to collagen was higher in the pre-warmed PC than in the non-warmed PC (33 +/- 5.9% coverage vs. 22 +/- 4.7% coverage, respectively, in a selected group with the same platelet concentration). The adhesion capacity to collagen of the platelets in the patient's blood, measured 10 min after transfusion, had increased considerably in both patient groups and 4 h later the adhesion capacity in both patient groups was similar to that of the pre-warmed PC before transfusion. We conclude that though pre-warming of stored PC had a beneficial effect on the adhesion capacity to collagen of the platelets in the PC, the clinical significance is questionable because already 10 min after transfusion the adhesion capacity to collagen of stored non-warmed platelets had improved to the level of the pre-warmed platelets and 4 h after transfusion this improvement was still present.