ABSTRACT
Aluminum nitride (AlN) thin films were grown using thermal atomic layer deposition in the temperature range of 175-350 °C. The thin films were deposited using trimethyl aluminum (TMA) and hydrazine (N2H4) as a metal precursor and nitrogen source, respectively. Highly reactive N2H4, compared to its conventionally used counterpart, ammonia (NH3), provides a higher growth per cycle (GPC), which is approximately 2.3 times higher at a deposition temperature of 300 °C and, also exhibits a low impurity concentration in as-deposited films. Low temperature AlN films deposited at 225 °C with a capping layer had an Al to N composition ratio of 1:1.1, a close to ideal composition ratio, with a low oxygen content (7.5%) while exhibiting a GPC of 0.16 nm/cycle. We suggest that N2H4 as a replacement for NH3 is a good alternative due to its stringent thermal budget.
ABSTRACT
Hexagonal boron nitride (h-BN) has been considered a promising dielectric for two-dimensional (2D) material-based electronics due to its atomically smooth and charge-free interface with an in-plane lattice constant similar to that of graphene. Here, we report atomic layer deposition of boron nitride (ALD-BN) using BCl3 and NH3 precursors directly on thermal SiO2 substrates at a relatively low temperature of 600 °C. The films were characterized by X-ray photoelectron spectroscopy, atomic force microscopy, and transmission electron microscopy wherein the uniform, atomically smooth, and nanocrystalline layered-BN thin film growth is observed. The growth rate is â¼0.042 nm/cycle at 600 °C, a temperature significantly lower than that of h-BN grown by chemical vapor deposition. The dielectric properties of the ALD-BN measured from Metal Oxide Semiconductor Capacitors are comparable with that of SiO2. Moreover, the ALD-BN exhibits a 2-fold increase in carrier mobility of graphene field effect transistors (G-FETs/ALD-BN/SiO2) due to the lower surface charge density and inert surface of ALD-BN in comparison to that of G-FETs fabricated on bare SiO2. Therefore, this work suggests that the transfer-free deposition of ALD-BN on SiO2 may be a promising candidate as a substrate for high performance graphene devices.
ABSTRACT
Though the synthesis of libraries of multicomponent metal oxide systems is prevalent using the combinatorial approach, the combinatorial approach has been rarely realized in studying simple metal oxides, especially applied to the atomic layer deposition (ALD) technique. In this literature, a novel combinatorial approach technique is utilized within an ALD grown simple metal oxide to synthesize a "spatially addressable combinatorial library". The two key factors in gradients were defined during the ALD process: (1) the process temperature and (2) a nonuniform flow of pulsed gases inside a cross-flow reactor. To validate the feasibility of our novel combinatorial approach, a case study of zinc oxide (ZnO), a simple metal oxide whose properties are well-known, is performed. Because of the induced gradient, the ZnO (002) crystallite size was found to gradually vary across a 100 mm wafer (â¼10-20 nm) with a corresponding increase in the normalized Raman E2/A1 peak intensity ratio. The findings agree well with the visible grain size observed from scanning electron microscope. The novel combinatorial approach provides a means of systematical interpretation of the combined effect of the two gradients, especially in the analysis of the microstructure of ZnO crystals. Moreover, the combinatorial library reveals that the process temperature, rather than the crystal size, plays the most significant role in determining the electrical conductivity of ZnO.
Subject(s)
Nanostructures/chemistry , Zinc Oxide/chemistry , Combinatorial Chemistry Techniques , Crystallography, X-Ray , Electric ConductivityABSTRACT
Correlations between physical properties linking film quality with wet etch rate (WER), one of the leading figures of merit, in plasma-enhanced atomic layer deposition (PEALD) grown silicon nitride (SiN x) films remain largely unresearched. Achieving a low WER of a SiN x film is especially significant in its use as an etch stopper for technology beyond 7 nm node semiconductor processing. Herein, we explore the correlation between the hydrogen concentration, hydrogen bonding states, bulk film density, residual impurity concentration, and the WERs of PEALD SiN x using Fourier transform infrared spectrometry, X-ray reflectivity, and spectroscopic ellipsometry, etc. PEALD SiN x films for this study were deposited using hexachlorodisilane and hollow cathode plasma source under a range of process temperatures (270-360 °C) and plasma gas compositions (N2/NH3 or Ar/NH3) to understand the influence of hydrogen concentration, hydrogen bonding states, bulk film density, and residual impurity concentration on the WER. Varying hydrogen concentration and differences in the hydrogen bonding states resulted in different bulk film densities and, accordingly, a variation in WER. We observe a linear relationship between hydrogen bonding concentration and WER as well as a reciprocal relationship between bulk film density and WER. Analogous to the PECVD SiN x processes, a reduction in hydrogen bonding concentration arises from either (1) thermal activation or (2) plasma excited species. However, unlike the case with silane (SiH4)-based PECVD SiN x, PEALD SiN x WERs are affected by residual impurities of Si precursors (i.e., chlorine impurity). Thus, possible wet etching mechanisms in HF in which the WER is affected by hydrogen bonding states or residual impurities are proposed. The shifts of amine basicity in SiN x due to different hydrogen bonding states and the changes in Si electrophilicity due to Cl impurity content are suggested as the main mechanisms that influence WER in the PEALD processes.
ABSTRACT
In this work, a novel chlorodisilane precursor, pentachlorodisilane (PCDS, HSi2Cl5), was investigated for the growth of silicon nitride (SiN x) via hollow cathode plasma-enhanced atomic layer deposition (PEALD). A well-defined self-limiting growth behavior was successfully demonstrated over the growth temperature range of 270-360 °C. At identical process conditions, PCDS not only demonstrated approximately >20% higher growth per cycle than that of a commercially available chlorodisilane precursor, hexachlorodisilane (Si2Cl6), but also delivered a better or at least comparable film quality determined by characterizing the refractive index, wet etch rate, and density of the films. The composition of the SiN x films grown at 360 °C using PCDS, as determined by X-ray photoelectron spectroscopy, showed low O content (â¼2 at. %) and Cl content (<1 at. %; below the detection limit). Fourier transform infrared spectroscopy spectra suggested that N-H bonds were the dominant hydrogen-containing bonds in the SiN x films without a significant amount of Si-H bonds originating from the precursor molecules. The possible surface reaction pathways of the PEALD SiN x using PCDS on the surface terminated with amine groups (-NH2 and -NH-) are proposed. The PEALD SiN x films grown using PCDS also exhibited a leakage current density as low as 1-2 nA/cm2 at 2 MV/cm and a breakdown electric field as high as â¼12 MV/cm.
ABSTRACT
Al/CuO energetic structure are attractive materials due to their high thermal output and propensity to produce gas. They are widely used to bond components or as next generation of MEMS igniters. In such systems, the reaction process is largely dominated by the outward migration of oxygen atoms from the CuO matrix toward the aluminum layers, and many recent studies have already demonstrated that the interfacial nanolayer between the two reactive layers plays a major role in the material properties. Here we demonstrate that the ALD deposition of a thin ZnO layer on the CuO prior to Al deposition (by sputtering) leads to a substantial increase in the efficiency of the overall reaction. The CuO/ZnO/Al foils generate 98% of their theoretical enthalpy within a single reaction at 900 °C, whereas conventional ZnO-free CuO/Al foils produce only 78% of their theoretical enthalpy, distributed over two distinct reaction steps at 550 °C and 850 °C. Combining high-resolution transmission electron microscopy, X-ray diffraction, and differential scanning calorimetry, we characterized the successive formation of a thin zinc aluminate (ZnAl2O4) and zinc oxide interfacial layers, which act as an effective barrier layer against oxygen diffusion at low temperature.
ABSTRACT
The successful realization of high-performance 2D-materials-based nanoelectronics requires integration of high-quality dielectric films as a gate insulator. In this work, we explore the integration of organic and inorganic hybrid dielectrics on MoS2 and study the chemical and electrical properties of these hybrid films. Our atomic force microscopy, X-ray photoelectron spectroscopy (XPS), Raman, and photoluminescence results show that, aside from the excellent film uniformity and thickness scalability down to 2.5 nm, the molecular layer deposition of octenyltrichlorosilane (OTS) and Al2O3 hybrid films preserves the chemical and structural integrity of the MoS2 surface. The XPS band alignment analysis and electrical characterization reveal that through the inclusion of an organic layer in the dielectric film, the band gap and dielectric constant can be tuned from â¼7.00 to 6.09 eV and â¼9.0 to 4.5, respectively. Furthermore, the hybrid films show promising dielectric properties, including a high breakdown field of â¼7.8 MV/cm, a low leakage current density of â¼1 × 10-6 A/cm2 at 1 MV/cm, a small hysteresis of â¼50 mV, and a top-gate subthreshold voltage swing of â¼79 mV/dec. Our experimental findings provide a facile way of fabricating scalable hybrid gate dielectrics on transition metal dichalcogenides for 2D-material-based flexible electronics applications.
ABSTRACT
Despite the number of existing studies that showcase the promising application of fluorinated graphene in nanoelectronics, the impact of the fluorine bonding nature on the relevant electrical behaviors of graphene devices, especially at low fluorine content, remains to be experimentally explored. Using CF4 as the fluorinating agent, we studied the gradual structural evolution of chemical vapor deposition graphene fluorinated by CF4 plasma at a working pressure of 700 mTorr using Raman and X-ray photoelectron spectroscopy (XPS). After 10 s of fluorination, our XPS analysis revealed a co-presence of covalently and ionically bonded fluorine components; the latter has been determined being a dominant contribution to the observation of two Dirac points in the relevant electrical measurement using graphene field effect transistor devices. Additionally, this ionic C-F component (ionic bonding characteristic charge sharing) is found to be present only at low fluorine content; continuous fluorination led to a complete transition to a covalently bonded C-F structure and a dramatic increase of graphene sheet resistance. Owing to the formation of these various C-F bonding components, our temperature-dependent Raman mapping studies show an inhomogeneous defluorination from annealing temperatures starting at â¼150 °C for low fluorine coverage, whereas fully fluorinated graphene is thermally stable up to â¼300 °C.
ABSTRACT
With the continued miniaturization of devices in the semiconductor industry, atomic layer deposition (ALD) of silicon nitride thin films (SiNx) has attracted great interest due to the inherent benefits of this process compared to other silicon nitride thin film deposition techniques. These benefits include not only high conformality and atomic-scale thickness control, but also low deposition temperatures. Over the past 20 years, recognition of the remarkable features of SiNx ALD, reinforced by experimental and theoretical investigations of the underlying surface reaction mechanism, has contributed to the development and widespread use of ALD SiNx thin films in both laboratory studies and industrial applications. Such recognition has spurred ever-increasing opportunities for the applications of the SiNx ALD technique in various arenas. Nevertheless, this technique still faces a number of challenges, which should be addressed through a collaborative effort between academia and industry. It is expected that the SiNx ALD will be further perceived as an indispensable technique for scaling next-generation ultra-large-scale integration (ULSI) technology. In this review, the authors examine the current research progress, challenges and future prospects of the SiNx ALD technique.
ABSTRACT
We present an Al2O3 dielectric layer on molybdenum disulfide (MoS2), deposited using atomic layer deposition (ALD) with ozone/trimethylaluminum (TMA) and water/TMA as precursors. The results of atomic force microscopy and low-energy ion scattering spectroscopy show that using TMA and ozone as precursors leads to the formation of uniform Al2O3 layers, in contrast to the incomplete coverage we observe when using TMA/H2O as precursors. Our Raman and X-ray photoelectron spectroscopy measurements indicate minimal variations in the MoS2 structure after ozone treatment at 200 °C, suggesting its excellent chemical resistance to ozone.