Ciprofloxacin antibiotic removal from aqueous solutions by ZnO nanoparticles coated on ACA: modeling and optimization.

Antibiotics are one of the most widely used drug groups. The presence of antibiotics in urban water sources and sewage creates many environmental and medical risks for humans and other living organisms. In this study, the potential of zinc oxide (ZnO) coated on almond shell activated carbon (ACA-ZnO) in removing ciprofloxacin (CIP) from aqueous solutions was investigated. Almond shell was used to make activated carbon. Zinc oxide nanoparticles were prepared by the sol-gel method, and finally, ZnO nanoparticles were bonded to activated carbon. The effect of independent parameters pH, contact time, adsorbent dose, and initial CIP concentration on CIP removal efficiency using ACA-ZnO was investigated by response surface methodology. Optimal removal was obtained at pH = 5.4, CIP initial concentration = 7.4 mg/L, adsorbent dose = 0.82 g/L, and reaction time = 67.3 min. This study followed a quadratic model (R2 = 0.958). The best model of adsorption isotherm fits with the Freundlich model (R2 = 0.9972) and the maximum capacity was 251.42 mg/g adsorption kinetics, and pseudo-second-order kinetic model (R2 = 0.959). The results of this study showed that ACA-ZnO as an adsorbent is very efficient, without environmental side effect and cost-benefit.

Statistical modeling and optimization of dexamethasone adsorption from aqueous solution by Fe3O4@NH2-MIL88B nanorods: Isotherm, Kinetics, and Thermodynamic.

The presence of pharmaceutical compounds in the environment poses a significant threat to human and aquatic animal health. Dexamethasone (DEX), a synthetic steroid hormone with endocrine-disrupting effects, is one such compound that needs to be effectively removed before discharging into the environment. This research presents a novel approach utilizing magnetically recyclable Fe3O4@NH2-MIL88B NRs as an efficient adsorbent for the treatment of DEX from aqueous solutions. The synthesized adsorbent was characterized by X-ray diffraction (XRD), scanning microscopy (SEM), transmission electron microscopy (TEM), vibrating sample magnetometer (VSM), diffuse reflectance spectra (DRS), and Fourier transform infrared spectroscopy (FTIR). Response surface methodology based on central composite design (RSM-CCD) was employed to optimize DEX removal efficiency by determining the optimal conditions, including pH, adsorbent dose, time, and DEX concentration. Under the optimized conditions (pH: 5.53, adsorbent dose: 0.185 g/L, time: 16.068 min, and DEX concentration: 33.491 mg/L), Fe3O4@NH2-MIL88B NRs revealed remarkable DEX adsorption efficiency of 91 ± 1.34% and adsorption capacity of 180.01 mg/g. The Langmuir isotherm and pseudo-second-order kinetic model were found to fit well with the experimental data, indicating a monolayer and chemical adsorption process. Thermodynamic analysis revealed that the adsorption process was spontaneous and endothermic. The study also investigated the inhibitory effect of background ions on DEX removal by Fe3O4@NH2-MIL88B NRs. Magnesium exhibited superior competitive ability with dexamethasone to occupy the active sites of the adsorbent compared to other background ions. The reuse of the adsorbent over ten consecutive cycles resulted in a 39.46% decrease in removal efficiency. The Fe3O4@NH2-MIL88B NRs are surrounded by abundant amounts of functional groups and π-electrons bands that can play a key role in the adsorption and separation of DEX from aqueous environments. The promising results obtained under real conditions highlight the potential of Fe3O4@NH2-MIL88B NRs as a practical and efficient adsorbent for the removal of DEX and other similar corticosteroids from aqueous solutions.

Photocatalytic degradation of bisphenol a from aqueous solution using bismuth ferric magnetic nanoparticle: synthesis, characterization and response surface methodology-central composite design modeling.

Purpose: Bisphenol A (BPA), as endocrine-disrupting compound (EDC), is extensively used as an important chemical in the synthesis of polycarbonate polymers and epoxy resins. BPA absorption into the body can result in the development of metabolic disorders such as low sex-specific neurodevelopment, immune toxicity, neurotoxicity and interference of cellular pathway. Therefore, the presence of BPA in the body and the environment can create hazards that must reach standards before being discharged into the environment. Methods: In this study, bismuth ferric nanomagnetic (BFO NMPs) were successfully synthesized via sol-gel method and developed as photocatalysts for BPA removal under visible light irradiation. FE-SEM, TEM, PL, XRD, UV-Vis DRS, VSM, EDX, and FTIR were used to characterize the BFO NMPs. Results: RSM model (R2 = 0.9745) showed a good correlation between experimental and predicted removal efficiency of BPA. The investigation of four independent variables indicated that pH had the most significant positive effect on the degradation of BPA. Under optimal conditions (pH = 4.042, catalyst dose = 7.617 mg, contact time = 122.742 min and BPA concentration = 15.065 mg/L), maximum degradation was calculated to be 98.7%. After five recycles, the removal of BPA remained >82%, which indicated the proper ability to reuse the catalyst. Conclusion: In conclusion, it can be stated like BPA, the prepared BFO NMPs is a promising photocatalyst for practical application in organic pollutant decomposition.

Health impact assessment and evaluation of economic costs attributed to PM2.5 air pollution using BenMAP-CE.

Air pollution is considered the most prominent public health. Economically, air pollution imposes additional costs on governments. This study aimed to quantify health effects and associated economic values of reducing PM2.5 air pollution using BenMAP-CE in Qom in 2019. The air quality data were acquired from Qom Province Environmental Protection Agency, and the population data were collected from Qom Province Management and Planning Organization website. The number of deaths due to Stroke, Chronic Obstructive Pulmonary Disease, Lung Cancer, and Ischemic Heart Disease attributable to PM2.5 were estimated using BenMAP-CE based on two control scenarios, 2.4 and 10 µg/m3, known as scenarios I and II, respectively. The associated economic effect of premature deaths was assessed by value of a statistical life (VSL) approach. The annual average of PM2.5 concentration was found to be 16.32 µg/m3 (SD: 9.93). A total of 4694.5 and 2475.94 premature deaths in scenarios I and II were found to be attributable to PM2.5 in overall, respectively. The total associated cost was calculated to be 855.91 and 451.40 million USD in scenarios I and II, respectively. The total years of life lost due to PM2.5 exposure in 2019 was 158,657.06 and 78,351.51 in scenarios I and II, respectively. The results of both health and economic assessment indicate the importance of solving the air pollution problem in Qom, as well as other big cities in Iran. The elimination of limitations, such as insufficient local data, should be regarded in future studies.

Estimation of the residential radon levels and the annual effective dose in dwellings of Shiraz, Iran, in 2015.

INTRODUCTION: Radon is the second most important cause of lung cancer after smoking. Thus, the determination of indoor radon concentrations in dwellings and workplaces is an important public health concern. The purpose of this research was to measure the concentration of radon gas in residential homes and public places in the city of Shiraz and its relationship with the type and age of the buildings as well as the type of materials used to construct the building (brick, block). We also determined the radon dosages that occupants of the building would receive. METHODS: The present study is a descriptive-analytical and cross-sectional research that was conducted on the building's indoor air in the city of Shiraz in 2015. Using geographic information system (GIS) software and a spatial sampling cell with an area of 25 square kilometers, 200 points were selected. In this study, we used passive diffusive samplers as Solid State Nuclear Track Detector (SSNTD) CR-39 polycarbonate films for three months in the winter. Sampling was conducted in accordance with the U.S. Environmental Protection Agency's protocol. We determined the concentrations of radon gas at the time of sampling, and calibration factors were determined. The data were analyzed by IBM-SPSS, version 20, descriptive statistics, Kruskal-Wallis, and Mann-Whitney tests. RESULTS: This study showed that the average radon concentration was 57.6 ± 33.06 Bq/m(3) in residential dwellings. The average effective dose was 1.45 mSv/y. The concentration of radon in 5.4% of the houses was found to be greater than 100 Bq/m(3), which is above the level allowed by the World Health Organization (WHO). CONCLUSION: Since radon is the second leading cause of lung cancer, it seems necessary to increase the public's awareness of this issue and to take action to reduce radon in homes when the concentrations are above the WHO's guideline.