Thermal Stability and Non-Linear Optical and Dielectric Properties of Lead-Free K0.5Bi0.5TiO3 Ceramics.

Lead-free K0.5Bi0.5TiO3 (KBT) ceramics with high density (~5.36 g/cm3, 90% of X-ray density) and compositional purity (up to 90%) were synthesized using a solid-state reaction method. Strongly condensed KBT ceramics revealed homogenous local microstructures. TG/DSC (Thermogravimetry-differential scanning calorimetry) techniques characterized the thermal and structural stability of KBT. High mass stability (>0.4%) has proven no KBT thermal decomposition or other phase precipitation up to 1000 °C except for the co-existing K2Ti6O13 impurity. A strong influence of crystallites size and sintering conditions on improved dielectric and non-linear optical properties was reported. A significant increase (more than twice) in dielectric permittivity (εR), substantial for potential applications, was found in the KBT-24h specimen with extensive milling time. Moreover, it was observed that the second harmonic generation (λSHG = 532 nm) was activated at remarkably low fundamental beam intensity. Finally, spectroscopic experiments (Fourier transform Raman and far-infrared spectroscopy (FT-IR)) were supported by DFT (Density functional theory) calculations with a 2 × 2 × 2 supercell (P42mc symmetry and C4v point group). Moreover, the energy band gap was calculated (Eg = 2.46 eV), and a strong hybridization of the O-2p and Ti-3d orbitals at Eg explained the nature of band-gap transition (Γ â†’ Γ).

High energy ball milling vs. nano spray drying in the development of supersaturated systems loaded with bosentan.

In this study, high energy ball milling and nano spray drying were used to prepare amorphous solid dispersions of bosentan in copovidone for the first time. In particular, the impact of this polymer on the bosentan amorphization kinetics was investigated. Copovidone was shown to facilitate the amorphization of bosentan upon ball milling. As a result, bosentan was dispersed in copovidone at the molecular level, forming amorphous solid dispersions, regardless of the ratio of the compounds. The similarity between the values of the adjustment parameter that describes the goodness of fit of the Gordon-Taylor equation to the experimental data (K = 1.16) and that theoretically calculated for an ideal mixture (K = 1.13) supported these findings. The kind of coprocessing method determined the powder microstructure and the release rate. The opportunity to prepare submicrometer-sized spherical particles using nano spray drying was an important advantage of this technology. Both coprocessing methods allowed the formation of long-lasting supersaturated bosentan solutions in the gastric environment with maximum concentrations reached ranging from four (11.20 µg/mL) to more than ten times higher (31.17 µg/mL) than those recorded when the drug was vitrified alone (2.76 µg/mL). Moreover, this supersaturation lasted for a period of time at least twice as long as that of the amorphous bosentan processed without copovidone (15 min vs. 30-60 min). Finally, these binary amorphous solid dispersions were XRD-amorphous for a year of storage under ambient conditions.

Antioxidant-Loaded Mesoporous Silica-An Evaluation of the Physicochemical Properties.

The dangerous effects of oxidative stress can be alleviated by antioxidants­substances with the ability to prevent damage caused by reactive oxygen species. The adsorption of antioxidants onto nanocarriers is a well-known method that might protect them against rough environ-mental conditions. The aim of this study was to investigate the adsorption and desorption of gallic acid (GA), protocatechuic acid (PCA), chlorogenic acid (CGA), and 4-hydroxybenzoic acid (4-HBA) using commercially available mesoporous silica materials (MSMs), both parent (i.e., SBA-15 and MCM-41) and surface functionalized (i.e., SBA-NH2 and SBA-SH). The MSMs loaded with active compounds were characterized using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), thermoporometry (TPM), and powder X-ray diffraction (XRD). High-performance liquid chromatography (HPLC-CAD) was used to evaluate the performance of the adsorption and desorption processes. The antioxidant potential was investigated using the Folin−Ciocalteu (FC) spectrophotometric method. Among the studied MSMs, the highest adsorption of GA was observed for amine-modified SBA-15 mesoporous silica. The adsorption capacity of SBA-NH2 increased in the order of PCA, 4-HBA < GA < CGA. Different desorption effectiveness levels of the adsorbed compounds were observed with the antioxidant capacity preserved for all investigated compounds.

Data regarding particle size distribution, thermal properties and gaseous phase hydration of co-milled solid dispersions composed of tadalafil and Soluplus.

A mechanical activation of the solid particles upon high-energy ball milling may considerably change the physicochemical properties of pharmaceutical compounds, including the morphology, particle size distribution, thermal properties, and surface interactions with water vapour upon gaseous phase hydration. Assessment of these changes is crucial for optimizing the manufacturing process of enabling drug products. In this article, we provide a detailed characterization of binary co-milled solid dispersions composed of tadalafil and Soluplus using a laser diffraction method, differential scanning calorimetry (DSC), gravimetric measurements and solid state 1H- NMR spectroscopy. The data presented in this article is directly related to our previously published research article. They complement information on the impact that both formulation and process variables may have on the properties of these binary powder formulations.

Thinking of bosentan repurposing - A study on dehydration and amorphization.

New clinical indications for an orphan drug bosentan are prompting the improvement of the drug formulation. Since bosentan is available as monohydrate, the information on its anhydrous form together with the assessment of its glass forming ability is necessary when developing enabling formulations. The aim of this research was, therefore, to analyze the phenomena occurring upon dehydration and amorphization of bosentan. The anhydrous form was obtained by a thermal treatment of the monohydrate and characterized for the first time using DSC and XRD. Two stable amorphous forms were prepared by cooling of the melt and high energy ball milling (Tg = 82 °C). The chemical stability of milled bosentan was evaluated using ATR-IR and 1H NMR as well. The kinetics of bosentan amorphization was established. It was stated that bosentan could be easily amorphized. Importantly, even if the system was semiamorphous, there was no recrystallization while heating. The concentration-time curves recorded in biorelevant media, confirmed the beneficial effect of amorphization on the dissolution of bosentan. Yet, the amorphous form recrystallized into the monohydrate form in the gastric milieu. This phenomenon was accompanied by a reversible color change from yellow, which is typical of bosentan glass, to creamywhite that is characteristic of the crude crystalline drug.

NiO-Ba0.95Ca0.05Ce0.9Y0.1O3-δ as a Modified Anode Material Fabricated by the Tape Casting Method.

The development of new chemically resistant anodes for protonic ceramic fuel cells (PCFCs) is urgently required to avoid the costly deep hydrogen purification method. Ba0.95Ca0.05Ce0.9Y0.1O3-δ (5CBCY), which is more chemically resistant than BaCaCe0.9Y0.1O3-δ, was here tested as a component of a composite NiO-5CBCY anode material. A preparation slurry comprising 5CBCY, NiO, graphite, and an organic medium was tape cast, sintered and subjected to thermal treatment in 10 vol.% H2 in Ar at 700 °C. Differential thermal analysis, thermogravimetry, quadrupole mass spectrometry, X-ray diffraction analysis, scanning electron microscopy, the AC four-probe method and electrochemical impedance spectroscopy were used for the investigation. The electrical conductivity of the Ni-5CBCY in H2-Ar at 700 °C was 1.1 S/cm. In the same gas atmosphere but with an additional 5 vol.% CO2, it was slightly lower, at 0.8 S/cm. The Ni-5CBCY cermet exhibited repeatable electrical conductivity values during Ni-to-NiO oxidation cycles and NiO-to-Ni reduction in the 5CBCY matrix, making it sufficient for preliminary testing in PCFCs.

3D direct printing of composite bone scaffolds containing polylactic acid and spray dried mesoporous bioactive glass-ceramic microparticles.

In this study, a three-dimensional composite scaffold is proposed consisting of polylactic acid and spray dried glass-ceramic microparticles (SGCMs). The compositional and structural characterization showed that the obtained spray dried powder formed as glass-ceramic (GC) with a completely interconnected porosity structure. Before direct printing of scaffolds, the rheological behavior of polylactic acid (PLA) and PLA-GC (PLA matrix containing SGCMs) inks were investigated. The PLA-GC composite ink represents sharper shear-thinning behavior and higher loss and storage modulus comparable to that of pure PLA. Microscopic observations and elemental mapping elements showed that 3D scaffolds had well-defined interconnected porosity and uniform distribution of the glass-ceramic particles. Mechanical tests indicated that compression strength is dependent on the scaffold porosity and the presence of SGCMs. Apatite formation evaluation besides ion release study showed better biomineralization capacity of PLA-GC scaffolds, as larger and denser sediments formed on the PLA-GC scaffolds after 7- and 14-day soaking. The preliminary cell response was studied with primary human mesenchymal stem cells (hMSCs) and revealed that SGCMs improved cell adhesion and viability and ALP activity. The appropriate combination of the biomaterials/methods to fabricate 3D porous constructs and their available bioactivity and biocompatibility, both being important characteristics for bone tissue engineering applications.

Hydration Patterns in Sodium Alginate Polymeric Matrix Tablets-The Result of Drug Substance Incorporation.

The purpose was to show, using destructive/nondestructive methods, that the interplay between water, tablet structure, and composition determine the unique spatiotemporal hydration pattern of polymer-based matrices. The tablets containing a 1:1 w/w mixture of sodium alginate with salicylic acid (ALG/SA) or sodium salicylate (ALG/SNA) were studied using Karl Fischer titration, differential scanning calorimetry, X-ray microtomography, and magnetic resonance imaging. As the principal results, matrix specific features were detected, e.g., "locking" of the internal part of the matrix (ALG/SA); existence of lamellar region associated with detection of free/freezing water (ALG/SA); existence of water penetrating the matrix forming specific region preceding infiltration layer (ALG/SNA); switch in the onset temperature of endothermic water peak associated with an increase in the fraction of non-freezing water weight per dry matrix weight in the infiltration layer (ALG/SNA). The existence of complicated spatiotemporal hydration patterns influenced by matrix composition and molecular properties of constituents has been demonstrated.

The Impact of the Preparation Method on the Properties of Orodispersible Films with Aripiprazole: Electrospinning vs. Casting and 3D Printing Methods.

Orodispersible films (ODFs) address the needs of pediatric and geriatric patients and people with swallowing difficulties due to fast disintegration in the mouth. Typically, they are obtained using the solvent casting method, but other techniques such as 3D printing and electrospinning have already been investigated. The decision on the manufacturing method is of crucial importance because it affects film properties. This study aimed to compare electrospun ODFs containing aripiprazole and polyvinyl alcohol with films prepared using casting and 3D printing methods. Characterization of films included DSC and XRD analysis, microscopic analysis, the assessment of mechanical parameters, disintegration, and dissolution tests. Simplified stability studies were performed after one month of storage. All prepared films met acceptance criteria for mechanical properties. Electrospun ODFs disintegrated in 1.0 s, which was much less than in the case of other films. Stability studies have shown the sensitivity of electrospun films to the storage condition resulting in partial recrystallization of ARP. These changes negatively affected the dissolution rate, but mechanical properties and disintegration time remained at a desirable level. The results demonstrated that electrospun fibers are promising solutions that can be used in the future for the treatment of patients with swallowing problems.

Poly(Vinyl Alcohol) Cryogel Membranes Loaded with Resveratrol as Potential Active Wound Dressings.

Hydrogel wound dressings are highly effective in the therapy of wounds. Yet, most of them do not contain any active ingredient that could accelerate healing. The aim of this study was to prepare hydrophilic active dressings loaded with an anti-inflammatory compound - trans-resveratrol (RSV) of hydrophobic properties. A special attention was paid to select such a technological strategy that could both reduce the risk of irritation at the application site and ensure the homogeneity of the final hydrogel. RSV dissolved in Labrasol was combined with an aqueous sol of poly(vinyl) alcohol (PVA), containing propylene glycol (PG) as a plasticizer. This sol was transformed into a gel under six consecutive cycles of freezing (-80 °C) and thawing (RT). White, uniform and elastic membranes were successfully produced. Their critical features, namely microstructure, mechanical properties, water uptake and RSV release were studied using SEM, DSC, MRI, texture analyser and Franz-diffusion cells. The cryogels made of 8 % of PVA showed optimal tensile strength (0.22 MPa) and elasticity (0.082 MPa). The application of MRI enabled to elucidate mass transport related phenomena in this complex system at the molecular (detection of PG, confinement effects related to pore size) as well as at the macro level (swelling). The controlled release of RSV from membranes was observed for 48 h with mean dissolution time of 18 h and dissolution efficiency of 35 %. All in all, these cryogels could be considered as a promising new active wound dressings.

Spatiotemporal Analysis of Hydration Mechanism in Sodium Alginate Matrix Tablets.

Methods of spatiotemporal characterization of nonequilibrated polymer based matrices are still immature and imperfect. The purpose of the study was to develop the methodology for the spatiotemporal characterization of water transport and properties in alginate tablets under hydration. The regions of low water content were spatially and temporally sampled using Karl Fisher and Differential Scanning Callorimetry (spatial distribution of freezing/nonfreezing water) with spatial resolution of 1 mm. In the regions of high water content, where sampling was infeasible due to gel/sol consistency, magnetic resonance imaging (MRI) enabled characterization with an order of magnitude higher spatial resolution. The minimally hydrated layer (MHL), infiltration layer (IL) and fully hydrated layer (FHL) were identified in the unilaterally hydrated matrices. The MHL gained water from the first hour of incubation (5-10% w/w) and at 4 h total water content was 29-39% with nonfreezing pool of 28-29%. The water content in the IL was 45-47% and at 4 h it reached ~50% with the nonfreezing pool of 28% and T2 relaxation time < 10 ms. The FHL consisted of gel and sol layer with water content of 85-86% with a nonfreezing pool of 11% at 4 h and T2 in the range 20-200 ms. Hybrid destructive/nondestructive analysis of alginate matrices under hydration was proposed. It allowed assessing the temporal changes of water distribution, its mobility and interaction with matrices in identified layers.

Towards plant-mediated chemistry - Au nanoparticles obtained using aqueous extract of Rosa damascena and their biological activity in vitro.

An eco-friendly, efficient, and controlled synthesis of gold nanoparticles with application of the aqueous extract of Rosa damascena (Au@RD NPs) without using any other reducing agents was studied. Au@RD NPs of narrow size distribution were characterized by UV-vis and FT-IR spectroscopies, transmission electron microscopy, X-ray powder diffraction, X-ray photoelectron spectroscopy, particle size analysis, and zeta potential measurements. In vitro stability experiments revealed that the Au@RD NPs were stable for over a year (pH ~ 3.5), proving a significant stabilizing potential of the aqueous RD extract. The high total content of polyphenols, flavonoids, and reducing sugars along with the powerful antioxidant activity of the RD extract was determined by spectroscopic and analytical methods. Colloids prepared from the purified and lyophilized Au@RD NPs (electrokinetic potential of ca. -33 mV) were stable for at least 24 h under terms similar to physiological conditions (pH = 7.4, PBS). The in vitro cytotoxicity of Au@RD NPs was investigated against peripheral blood mononuclear lymphocytes (PBML), acute promyelocytic leukemia (HL60), and human lung adenocarcinoma (A549). Selective cytotoxicity of Au@RD NPs towards cancer cells (HL60, A549) over normal cells (PBML) in vitro was explicitly demonstrated by viability assays. Comet assay revealed a higher level of DNA damages in cancer cells when compared with normal ones. Apoptotic death in cancer cells was proved by measuring caspases activity. Thus, the developed Au@RD NPs, obtained by the plant-mediated green synthesis, are attractive hybrid materials for the medical applications combining two active components - metal nanoparticles platform and plant-derived metabolites.

Tailored Synthesis of PEGylated Bismuth Nanoparticles for X-ray Computed Tomography and Photothermal Therapy: One-Pot, Targeted Pyrolysis, and Self-Promotion.

Complex experimental design is a common problem in the preparation of theranostic nanoparticles, resulting in poor reaction control, expensive production cost, and low experiment success rate. The present study aims to develop PEGylated bismuth (PEG-Bi) nanoparticles with a precisely controlled one-pot approach, which contains only methoxy[(poly(ethylene glycol)]trimethoxy-silane (PEG-silane) and bismuth oxide (Bi2O3). A targeted pyrolysis of PEG-silane was achieved to realize its roles as both the reduction and PEGylation agents. The unwanted methoxy groups of PEG-silane were selectively pyrolyzed to form reductive agents, while the useful PEG-chain was fully preserved to enhance the biocompatibility of Bi nanoparticles. Moreover, Bi2O3 not only acted as the raw material of the Bi source but also presented a self-promotion in the production of Bi nanoparticles via catalyzing the pyrolysis of PEG-silane. The reaction mechanism was systematically validated with different methods such as nuclear magnetic resonance spectroscopy. The PEG-Bi nanoparticles showed better compatibility and photothermal conversion than those prepared by the complex multiple step approaches in literature studies. In addition, the PEG-Bi nanoparticles possessed prominent performance in X-ray computed tomography imaging and photothermal cancer therapy in vivo. The present study highlights the art of precise reaction control in the synthesis of PEGylated nanoparticles for biomedical applications.

Evaluation of the Textural Parameters of Zeolite Beta in LDPE Catalytic Degradation: Thermogravimetric Analysis Coupled with FTIR Operando Studies.

Zeolite-based catalysts are globally employed in many industrial processes, such as crude-oil refining and bulk chemical production. In this work, the cracking of low-density polyethylene (LDPE) was thoroughly followed in a FTIR operando study to examine the catalytic efficiency of purely microporous zeolites of various textural characteristics. To provide complementary and valuable information on the catalytic activity of the zeolite studied, the thermogravimetric analysis results were compared with yields of the products generated under operating conditions. The reaction products were analyzed via GC-MS to determine the hydrocarbon chain distribution in terms of paraffin, olefins, and aromatics. The individual impact of textural and acidic parameters on catalytic parameters was assessed. The accumulation of bridging hydroxyls of high strength in the zeolite benefited the decrease in polymer decomposition temperature. Through a strategic comparison of purely microporous zeolites, we showed that the catalytic cracking of LDPE is dominated by the acidic feature inherent to the microporous environment.

Silica-Polymer Composites as the Novel Antibiotic Delivery Systems for Bone Tissue Infection.

Bone tissue inflammation, osteomyelitis, is commonly caused by bacterial invasion and requires prolonged antibiotic therapy for weeks or months. Thus, the aim of this study was to develop novel silica-polymer local bone antibiotic delivery systems characterized by a sustained release of ciprofloxacin (CIP) which remain active against Staphylococcus aureus for a few weeks, and do not have a toxic effect towards human osteoblasts. Four formulations composed of ethylcellulose (EC), polydimethylsiloxane (PDMS), freeze-dried CIP, and CIP-adsorbed mesoporous silica materials (MCM-41-CIP) were prepared via solvent-evaporation blending method. All obtained composites were characterized in terms of molecular structure, morphological, and structural properties by using Fourier Transform Infrared Spectroscopy (FTIR), scanning electron microscopy equipped with energy-dispersive X-ray spectroscopy (SEM/EDX), and X-ray diffraction (XRD), thermal stability by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC), and in vitro antibiotic release. The antibacterial activity against Staphylococcus aureus (ATCC 6538) as well as the in vitro cytocompatibility to human osteoblasts of obtained composites were also examined. Physicochemical results confirmed the presence of particular components (FTIR), formation of continuous polymer phase onto the surface of freeze-dried CIP or MCM-41-CIP (SEM/EDX), and semi-crystalline (composites containing freeze-dried CIP) or amorphous (composites containing MCM-41-CIP) structure (XRD). TGA and DSC analysis indicated the high thermal stability of CIP adsorbed onto the MCM-41, and higher after MCM-41-CIP coating with polymer blend. The release study revealed the significant reduction in initial burst of CIP for the composites which contained MCM-41-CIP instead of freeze-dried CIP. These composites were also characterized by the 30-day activity against S. aureus and the highest cytocompatibility to human osteoblasts in vitro.

Physicochemical Properties of Bosentan and Selected PDE-5 Inhibitors in the Design of Drugs for Rare Diseases.

The study provides the physicochemical characteristic of bosentan (BOS) in comparison to tadalafil (TA) and sildenafil citrate (SIL). Despite some reports dealing with thermal characteristic of SIL and TA, physicochemical properties of BOS have not been investigated so far. Recent clinical reports have indicated that the combination of bosentan and PDE-5 inhibitor can improve the effectiveness of pharmacotherapy of pulmonary arterial hypertension (PAH). However, in order to design personalized medicines for therapy of chronic rare diseases, detailed information on the thermal behaviour and solubility of each drug is indispensable. Thus, XRD, DSC and TGA-QMS analyses were applied to compare the properties of the drugs, their thermal stability as well as to identify the products of thermal degradation. The dehydration of BOS started at 70°C and was followed by the chemical degradation with the onset at 290°C. The highest thermal stability was stated for TA, which decomposed at ca. 320°C, whereas the lowest onset of the thermal decomposition process was stated for SIL, i.e. 190°C. The products of the drug decomposition were identified. FT-FIR was applied to study intra- and intermolecular interactions between the drug molecules. FT-MIR and Raman spectroscopy were used to examine the chemical structure of the drugs. Chemoinformatic tools were used to predict the polar surface area, pKa, or logP of the drugs. Their results were in line with solubility and dissolution studies.