Supersoft Norbornene-Based Thermoplastic Elastomers with High Strength and Upper Service Temperature.

With over 6 million tons produced annually, thermoplastic elastomers (TPEs) have become ubiquitous in modern society, due to their unique combination of elasticity, toughness, and reprocessability. Nevertheless, industrial TPEs display a tradeoff between softness and strength, along with low upper service temperatures, typically ≤100 °C. This limits their utility, such as in bio-interfacial applications where supersoft deformation is required in tandem with strength, in addition to applications that require thermal stability (e.g., encapsulation of electronics, seals/joints for aeronautics, protective clothing for firefighting, and biomedical devices that can be subjected to steam sterilization). Thus, combining softness, strength, and high thermal resistance into a single versatile TPE has remained an unmet opportunity. Through de novo design and synthesis of novel norbornene-based ABA triblock copolymers, this gap is filled. Ring-opening metathesis polymerization is employed to prepare TPEs with an unprecedented combination of properties, including skin-like moduli (<100 kPa), strength competitive with commercial TPEs (>5 MPa), and upper service temperatures akin to high-performance plastics (≈260 °C). Furthermore, the materials are elastic, tough, reprocessable, and shelf stable (≥2 months) without incorporation of plasticizer. Structure-property relationships identified herein inform development of next-generation TPEs that are both biologically soft yet thermomechanically durable.

Effect of Europium and Gadolinium Alloying Elements on the Tribological Response of Low Hydrogen Content Amorphous Carbon.

Dopants and alloying elements are commonly introduced in amorphous carbon (a-C) materials to tailor their mechanical and tribological properties. While most published studies have focused on doping and alloying a-C coatings with metals or metalloids, doping a-C films with rare-earth elements has only recently been explored. Notably, our understanding of the shear-induced structural changes occurring in rare-earth-element-containing a-C films is still elusive, even in the absence of any liquid lubricants. Here, the friction response of Eu- and Gd-containing a-C films with low hydrogen content deposited by HiPIMS on silicon was evaluated in open air and at room temperature. The load-dependent friction measurements indicated that the introduction of Gd ((2.3 ± 0.1) at.%) and Eu ((2.4 ± 0.1) at.%) into the a-C matrix results in a significant reduction of the shear strength of the sliding interfaces ((41 ± 2) MPa for a-C, (16 ± 1) MPa for a-C:Gd2.3 at.%, and (11 ± 2) MPa for a-C:Eu2.4 at.%). NEXAFS spectromicroscopy experiments provided evidence that no stress-assisted sp3-to-sp2 rehybridization of carbon atoms was induced by the sliding process in the near-surface region of undoped a-C, while the amount of sp2-bonded carbon progressively increased in a-C:Gd2.3 at.% and a-C:Eu2.4 at.% upon increasing the applied normal load in tribological tests. The formation of an sp2-bonded carbon-rich surface layer in a-C:Gd2.3 at.% and a-C:Eu2.4 at.% films was not only proposed to be the origin for the reduced duration of the running-in period in tribological test, but was also postulated to induce shear localization within the sp2-carbon-rich layer and transfer film formation on the countersurface, thus decreasing the interfacial shear strength. These findings open the path for the use of Gd- and Eu-containing a-C even under critical conditions for nearly hydrogen-free a-C films (i.e., humid air).

Effect of Camera Parallax Angle on the Accuracy of Static Contact Angle Measurements.

Measuring the contact angle at the solid/liquid/vapor triple point in sessile drop experiments is one of the most popular and simple ways to quantify the wettability of surfaces and determine the surface free energy. Despite decades of technical advancements in contact angle measurements, which allowed for improving the precision of sessile drop measurements below ±1°, an often overlooked source of experimental error in these measurements originates from the camera's parallax angle (PA) - the angle between the camera optical axis and the sample stage surface. Here, we quantified the systematic errors in the measurement of contact angles due to the acquisition of drop images at finite PA values by simulating sessile drop experiments in which synthetic drops were created using the Young-Laplace equation. The absolute contact angle error induced by imaging drops at nonzero PAs was found to increase as the true contact angle (TCA) deviates from 90° and resulted in an overestimation (underestimation) of the contact angle for drops having TCAs lower (higher) than 90°. The computed absolute contact angle error reaches values as high as -20° (+12.2°) for drops having a TCA of 175° (5°) when imaged with a PA of 10°, thus indicating the importance of considering the PA when accurately quantifying contact angles in sessile drop experiments. The shape and, by extension, volume of the sessile drop was also found to affect the magnitude of the absolute contact angle error as sessile drops with higher apex curvatures exhibited lower absolute error than those with lower curvatures at any given PA. The outcomes of this work provide guidelines for minimizing systematic errors in sessile drop measurements due to the collection of drop images at nonzero PAs.

Spectroscopic Evaluation of Surface Chemical Processes Occurring in MoS2 upon Aging.

Molybdenum disulfide (MoS2) coatings have attracted widespread industrial interest owing to their excellent lubricating properties under vacuum and inert conditions. Unfortunately, the increase in MoS2 interfacial shear strength following prolonged exposure to ambient conditions (a process referred to as "aging") has resulted in reliability issues when MoS2 is employed as solid lubricant. While aging of MoS2 is generally attributed to physical and chemical changes caused by adsorbed water and/or oxygen, a mechanistic understanding of the relative role of these two gaseous species in the evolution of the surface chemistry of MoS2 is still elusive. Additionally, remarkably little is known about the effect of thermally- and tribologically-induced microstructural variations in MoS2 on the aging processes occurring in the near-surface region of the coating. Here, we employed three analytical techniques, namely, X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS), and grazing-incidence X-ray diffraction (GIXRD), to gain insights into the aging phenomena occurring in sputtered MoS2 coatings before and after tribological testing, while also evaluating the impact of thermally-induced variations in the coating structure on aging. The outcomes of XPS analyses provide evidence that a substantial surface oxidation of MoS2 only takes place under humid conditions. Furthermore, the correlation of XPS, ToF-SIMS, and GIXRD results allowed for the development of a qualitative model for the impact of shear-induced microstructural variations in MoS2 on the transport of water in the near-surface region of this material and on the extent of surface oxidation. These results add significantly to our understanding of the aging mechanisms of MoS2 coatings used in tribological applications and their dependence on environmental conditions.

Multimorphic Materials: Spatially Tailoring Mechanical Properties via Selective Initiation of Interpenetrating Polymer Networks.

Access to multimaterial polymers with spatially localized properties and robust interfaces is anticipated to enable new capabilities in soft robotics, such as smooth actuation for advanced medical and manufacturing technologies. Here, orthogonal initiation is used to create interpenetrating polymer networks (IPNs) with spatial control over morphology and mechanical properties. Base catalyzes the formation of a stiff and strong polyurethane, while blue LEDs initiate the formation of a soft and elastic polyacrylate. IPN morphology is controlled by when the LED is turned "on", with large phase separation occurring for short time delays (≈1-2 min) and a mixed morphology for longer time delays (>5 min), which is supported by dynamic mechanical analysis, small angle X-ray scattering, and atomic force microscopy. Through tailoring morphology, tensile moduli and fracture toughness can be tuned across ≈1-2 orders of magnitude. Moreover, a simple spring model is used to explain the observed mechanical behavior. Photopatterning produces "multimorphic" materials, where morphology is spatially localized with fine precision (<100 µm), while maintaining a uniform chemical composition throughout to mitigate interfacial failure. As a final demonstration, the fabrication of hinges represents a possible use case for multimorphic materials in soft robotics.

Entrapment of air microbubbles by ice crystals during freezing exacerbates freeze-induced denaturation of proteins.

Freezing techniques are an essential part of biologics manufacturing processes, yet the formation of ice/water interfaces can impart detrimental effects on proteins. However, the absence of chemical and structural differences between ice and liquid water poses the question as to why ice can destabilize proteins. We hypothesize that the destabilizing stress of the ice-liquid water interface does not originate from the ice-water system itself but rather from the air microbubbles present during the freezing process. As the temperature decreases, the dissolved air is expelled from the ice crystal lattices in the form of microbubbles and is subsequently trapped by the advancing ice front. This newly formed air-water interface represents an additional interfacial area for the proteins to be adsorbed onto and denatured. The result showed that freezing at âˆ¼ 1 K/s led to the formation of small circular microbubbles with diameters ranging from 100 µm to 500 µm. In contrast, slower freezing resulted in the formation of larger, elongated millimeter-size bubbles. The reduction of the number of microbubbles was carried out by the deaeration process using agitation under reduced pressure at 20 kPa. The resulting deaerated (i.e., low dissolved air) protein samples were frozen and monitored for the formation of subvisible aggregates using micro-flow imaging (MFI). The results demonstrated that deaerating the samples prior to intermediate freezing (i.e., TFF) reduced the number of aggregates for both highly surface-active and low surface-active proteins (lactoferrin and bovine IgG, respectively). This reduction was more pronounced in spray freeze drying (SFD) than thin-film freezing (TFF), and less apparent in conventional lyophilization.

Aggregation of Lactoferrin Caused by Droplet Atomization Process via a Two-Fluid Nozzle: The Detrimental Effect of Air-Water Interfaces.

Biological macromolecules, especially therapeutic proteins, are delicate and highly sensitive to denaturation from stresses encountered during the manufacture of dosage forms. Thin-film freeze-drying (TFFD) and spray freeze-drying (SFD) are two processes used to convert liquid forms of protein into dry powders. In the production of inhalable dry powders that contain proteins, these potential stressors fall into three categories based on their occurrence during the primary steps of the process: (1) droplet formation (e.g., the mechanism of droplet formation, including spray atomization), (2) freezing, and (3) frozen water removal (e.g., sublimation). This study compares the droplet formation mechanism used in TFFD and SFD by investigating the effects of spraying on the stability of proteins, using lactoferrin as a model. This study considers various perspectives on the denaturation (e.g., conformation) of lactoferrin after subjecting the protein solution to the atomization process using a pneumatic two-fluid nozzle (employed in SFD) or a low-shear drop application through the nozzle. The surface activity of lactoferrin was examined to explore the interfacial adsorption tendency, diffusion, and denaturation process. Subsequently, this study also investigates the secondary and tertiary structure of lactoferrin and the quantification of monomers, oligomers, and, ultimately, aggregates. The spraying process affected the tertiary structure more negatively than the tightly woven secondary structure, resulting in the peak position corresponding to the tryptophan (Trp) residues red-shifting by 1.5 nm. This conformational change can either (a) be reversed at low concentrations via relaxation or (b) proceed to form irreversible aggregates at higher concentrations. Interestingly, when the sample was allowed to progress into micrometer-sized aggregates, such a dramatic change was not detected using methods such as size-exclusion chromatography, polyacrylamide gel electrophoresis, and dynamic light scattering at 173°. A more complete understanding of the heterogeneous protein sample was achieved only through a combination of 173 and 13° backward and forward scattering, a combination of derived count rate measurements, and microflow imaging (MFI). After studying the impact of droplet formation mechanisms on aggregation tendency of lactoferrin, we further investigated two additional model proteins with different surface activity: bovine IgG (serving as a non surface-active negative reference), and ß-galactosidase (another surface-active protein). The results corroborated the lactoferrin findings that spray-atomization-related stress-induced protein aggregation was much more pronounced for proteins that are surface active (lactoferrin and ß-galactosidase), but it was minimal for non-surface-active protein (bovine IgG). Finally, compared to the low-shear dripping used in the TFFD process, lactoferrin underwent a relatively fast conformational change upon exposure to the high air-water interface of the two-fluid atomization nozzle used in the SFD process as compared to the low shear dripping used in the TFFD process. The interfacial-induced denaturation that occurred during spraying was governed primarily by the size of the atomized droplets, regardless of the duration of exposure to air. The percentage of denatured protein population and associated activity loss, in the case of ß-galactosidase, was determined to range from 2 to 10% depending on the air-flow rate of the spraying process.

Investigation of Multilayered Structures of Ionic Liquids on Graphite and Platinum Using Atomic Force Microscopy and Molecular Simulations.

The molecular-level orientation and structure of ionic liquids (ILs) at liquid-solid interfaces are significantly different than in the bulk. The interfacial ordering influences both IL properties, such as dielectric constants and viscosity, and their efficacy in devices, such as fuel cells and electrical capacitors. Here, we report the layered structures of four ILs on unbiased, highly ordered pyrolytic graphite (HOPG) and Pt(111) surfaces, as determined by atomic force microscopy. The ILs investigated are 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([emim][Tf2N]), 1-ethyl-3-methylimidazolium perfluorobutylsulfonate ([emim][C4F9SO3]), 7-methyl-1,5,7-triazabicyclo[4.4.0]dec-5-ene bis(trifluoromethylsulfonyl)imide ([MTBD][Tf2N]), and 7-methyl-1,5,7-triazabicyclo[4.4.0]dec-5-ene perfluorobutylsulfonate ([MTBD][C4F9SO3]). Molecular dynamics simulations provide complementary information on the position and orientation of the ions. These ILs form a cation layer at the IL-solid interface, followed by a layer of anions. [Emim]+ and [MTBD]+ have similar orientations at the surface, but [MTBD]+ forms a thinner layer compared to [emim]+ on both HOPG and Pt(111). In addition, [Tf2N]- shows stronger interactions with Pt(111) surfaces than [C4F9SO3]-.

Wafer-Scalable Single-Layer Amorphous Molybdenum Trioxide.

Molybdenum trioxide (MoO3), an important transition metal oxide (TMO), has been extensively investigated over the past few decades due to its potential in existing and emerging technologies, including catalysis, energy and data storage, electrochromic devices, and sensors. Recently, the growing interest in two-dimensional (2D) materials, often rich in interesting properties and functionalities compared to their bulk counterparts, has led to the investigation of 2D MoO3. However, the realization of large-area true 2D (single to few atom layers thick) MoO3 is yet to be achieved. Here, we demonstrate a facile route to obtain wafer-scale monolayer amorphous MoO3 using 2D MoS2 as a starting material, followed by UV-ozone oxidation at a substrate temperature as low as 120 °C. This simple yet effective process yields smooth, continuous, uniform, and stable monolayer oxide with wafer-scale homogeneity, as confirmed by several characterization techniques, including atomic force microscopy, numerous spectroscopy methods, and scanning transmission electron microscopy. Furthermore, using the subnanometer MoO3 as the active layer sandwiched between two metal electrodes, we demonstrate the thinnest oxide-based nonvolatile resistive switching memory with a low voltage operation and a high ON/OFF ratio. These results (potentially extendable to other TMOs) will enable further exploration of subnanometer stoichiometric MoO3, extending the frontiers of ultrathin flexible oxide materials and devices.

How Hydrogen and Oxygen Vapor Affect the Tribochemistry of Silicon- and Oxygen-Containing Hydrogenated Amorphous Carbon under Low-Friction Conditions: A Study Combining X-ray Absorption Spectromicroscopy and Data Science Methods.

The incorporation of silicon and oxygen into hydrogenated amorphous carbon (a-C:H) is an effective approach to decrease the dependence of the tribological properties of a-C:H on the environment. Here, we evaluate the effect of hydrogen and oxygen partial pressures in vacuum on the tribological response of steel pins sliding against films consisting of silicon- and oxygen-containing a-C:H (a-C:H:Si:O). Experiments are conducted in the low-friction/low-wear regime, where sufficient gas pressure prevents steel from adhering to the a-C:H:Si:O, with the velocity accommodation mode being interfacial sliding between the tribotrack formed in the a-C:H:Si:O film and the carbonaceous tribofilm that is formed on the countersurface. The experiments indicated a decrease (increase) in friction and wear with the hydrogen (oxygen) pressure (hydrogen pressures between 50 and 2000 mbar; oxygen pressures between 10 and 1000 mbar). Characterization by X-ray photoelectron and absorption spectroscopies indicated the occurrence of tribologically induced rehybridization of carbon-carbon bonds from sp3 to sp2. This mechanically induced structural transformation coincided with the dissociative surface reaction between hydrogen (oxygen) gas molecules and sp2 carbon-carbon bonds that are highly strained, which results in the formation of carbon-hydrogen groups (carbonyl or ether groups together with silicon atoms having higher oxidation states). On the basis of variations of the fraction of these surface functional groups with gas pressure, a phenomenological model is proposed for the gas pressure dependence of friction for steel when sliding on a-C:H:Si:O films: while the decrease in friction with hydrogen pressure is induced by an increase in the percentage of carbon-hydrogen groups, the increase in friction with oxygen pressure is caused by a progressive increase in the relative fraction of silicon atoms having higher oxidation states and an increase in surface oxygen concentration.

In situ nanoscale evaluation of pressure-induced changes in structural morphology of phosphonium phosphate ionic liquid at single-asperity contacts.

In this work, we perform atomic force microscopy (AFM) experiments to evaluate in situ the dependence of the structural morphology of trihexyltetradecylphosphonium bis(2-ethylhexyl) phosphate ([P6,6,6,14][DEHP]) ionic liquid (IL) on applied pressure. The experimental results obtained upon sliding a diamond-like-carbon-coated silicon AFM tip on mechanically polished steel at an applied pressure up to 5.5 ± 0.3 GPa indicate a structural transition of confined [P6,6,6,14][DEHP] molecules. This pressure-induced morphological change of [P6,6,6,14][DEHP] IL leads to the generation of a lubricious, solid-like interfacial layer, whose growth rate increases with applied pressure and temperature. The structural variation of [P6,6,6,14][DEHP] IL is proposed to derive from the well-ordered layering of the polar groups of ions separated by the apolar tails. These results not only shed new light on the structural organization of phosphonium-based ILs under elevated pressure, but also provide novel insights into the normal pressure-dependent lubrication mechanisms of ILs in general.

Engineering encapsulated ionic liquids for next-generation applications.

Ionic liquids (ILs) have attracted considerable attention in several sectors (from energy storage to catalysis, from drug delivery to separation media) owing to their attractive properties, such as high thermal stability, wide electrochemical window, and high ionic conductivity. However, their high viscosity and surface tension compared to conventional organic solvents can lead to unfavorable transport properties. To circumvent undesired kinetics effects limiting mass transfer, the discretization of ILs into small droplets has been proposed as a method to increase the effective surface area and the rates of mass transfer. In the present review paper, we summarize the different methods developed so far for encapsulating ILs in organic or inorganic shells and highlight characteristic features of each approach, while outlining potential applications. The remarkable tunability of ILs, which derives from the high number of anions and cations currently available as well as their permutations, combines with the possibility of tailoring the composition, size, dispersity, and properties (e.g., mechanical, transport) of the shell to provide a toolbox for rationally designing encapsulated ILs for next-generation applications, including carbon capture, energy storage devices, waste handling, and microreactors. We conclude this review with an outlook on potential applications that could benefit from the possibility of encapsulating ILs in organic and inorganic shells.

Thermally Induced Structural Evolution of Silicon- and Oxygen-Containing Hydrogenated Amorphous Carbon: A Combined Spectroscopic and Molecular Dynamics Simulation Investigation.

Silicon- and oxygen-containing hydrogenated amorphous carbon (a-C:H:Si:O) coatings are amorphous thin-film materials composed of hydrogenated amorphous carbon (a-C:H), doped with silicon and oxygen. Compared to a-C:H, a-C:H:Si:O exhibits much lower susceptibility to oxidative degradation and higher thermal stability, making a-C:H:Si:O attractive for many applications. However, the physical mechanisms for this improved behavior are not understood. Here, the thermally induced structural evolution of a-C:H:Si:O was investigated in situ by X-ray photoelectron and absorption spectroscopy, as well as molecular dynamics (MD) simulations. The spectroscopy results indicate that upon high vacuum annealing, two thermally activated processes with a Gaussian distribution of activation energies with mean value E and standard deviation σ take place in a-C:H:Si:O: (a) ordering and clustering of sp2 carbon ( E ± σ = 0.22 ± 0.08 eV) and (b) conversion of sp3- to sp2-bonded carbon ( E ± σ = 3.0 ± 1.1 eV). The experimental results are in qualitative agreement with the outcomes of MD simulations performed using a ReaxFF potential. The MD simulations also indicate that the higher thermal stability of a-C:H:Si:O compared to a-C:H (with similar fraction of sp2-bonded carbon and hydrogen content) derives from the significantly lower fraction of strained carbon-carbon sp3 bonds in a-C:H:Si:O compared to a-C:H, which are more likely to break at elevated temperatures.

Valence Band Control of Metal Silicide Films via Stoichiometry.

The unique electronic and mechanical properties of metal silicide films render them interesting for advanced materials in plasmonic devices, batteries, field-emitters, thermoelectric devices, transistors, and nanoelectromechanical switches. However, enabling their use requires precisely controlling their electronic structure. Using platinum silicide (PtxSi) as a model silicide, we demonstrate that the electronic structure of PtxSi thin films (1 ≤ x ≤ 3) can be tuned between metallic and semimetallic by changing the stoichiometry. Increasing the silicon content in PtxSi decreases the carrier density according to valence band X-ray photoelectron spectroscopy and theoretical density of states (DOS) calculations. Among all PtxSi phases, Pt3Si offers the highest DOS due to the modest shift of the Pt5d manifold away from the Fermi edge by only 0.5 eV compared to Pt, rendering it promising for applications. These results, demonstrating tunability of the electronic structure of thin metal silicide films, suggest that metal silicides can be designed to achieve application-specific electronic properties.

Quantitative Evaluation of the Carbon Hybridization State by Near Edge X-ray Absorption Fine Structure Spectroscopy.

The characterization of the local bonding configuration of carbon in carbon-based materials is of paramount importance since the properties of such materials strongly depend on the distribution of carbon hybridization states, the local ordering, and the degree of hydrogenation. Carbon 1s near edge X-ray absorption fine structure (NEXAFS) spectroscopy is one of the most powerful techniques for gaining insights into the bonding configuration of near-surface carbon atoms. The common methodology for quantitatively evaluating the carbon hybridization state using C 1s NEXAFS measurements, which is based on the analysis of the sample of interest and of a highly ordered pyrolytic graphite (HOPG) reference sample, was reviewed and critically assessed, noting that inconsistencies are found in the literature in applying this method. A theoretical rationale for the specific experimental conditions to be used for the acquisition of HOPG reference spectra is presented together with the potential sources of uncertainty and errors in the correctly computed fraction of sp(2)-bonded carbon. This provides a specific method for analyzing the distribution of carbon hybridization state using NEXAFS spectroscopy. As an illustrative example, a hydrogenated amorphous carbon film was analyzed using this method and showed good agreement with X-ray photoelectron spectroscopy (which is surface sensitive). Furthermore, the results were consistent with analysis from Raman spectroscopy (which is not surface sensitive), indicating the absence of a structurally different near-surface region in this particular thin film material. The present work can assist surface scientists in the analysis of NEXAFS spectra for the accurate characterization of the structure of carbon-based materials.

Accounting for nanometer-thick adventitious carbon contamination in X-ray absorption spectra of carbon-based materials.

Near-edge X-ray absorption fine structure (NEXAFS) spectroscopy is a powerful technique for characterizing the composition and bonding state of nanoscale materials and the top few nanometers of bulk and thin film specimens. When coupled with imaging methods like photoemission electron microscopy, it enables chemical imaging of materials with nanometer-scale lateral spatial resolution. However, analysis of NEXAFS spectra is often performed under the assumption of structural and compositional homogeneity within the nanometer-scale depth probed by this technique. This assumption can introduce large errors when analyzing the vast majority of solid surfaces due to the presence of complex surface and near-surface structures such as oxides and contamination layers. An analytical methodology is presented for removing the contribution of these nanoscale overlayers from NEXAFS spectra of two-layered systems to provide a corrected photoabsorption spectrum of the substrate. This method relies on the subtraction of the NEXAFS spectrum of the overlayer adsorbed on a reference surface from the spectrum of the two-layer system under investigation, where the thickness of the overlayer is independently determined by X-ray photoelectron spectroscopy (XPS). This approach is applied to NEXAFS data acquired for one of the most challenging cases: air-exposed hard carbon-based materials with adventitious carbon contamination from ambient exposure. The contribution of the adventitious carbon was removed from the as-acquired spectra of ultrananocrystalline diamond (UNCD) and hydrogenated amorphous carbon (a-C:H) to determine the intrinsic photoabsorption NEXAFS spectra of these materials. The method alters the calculated fraction of sp(2)-hybridized carbon from 5 to 20% and reveals that the adventitious contamination can be described as a layer containing carbon and oxygen ([O]/[C] = 0.11 ± 0.02) with a thickness of 0.6 ± 0.2 nm and a fraction of sp(2)-bonded carbon of 0.19 ± 0.03. This method can be generally applied to the characterization of surfaces and interfaces in several research fields and technological applications.

Nonaqueous synthesis of TiO2 nanocrystals using TiF4 to engineer morphology, oxygen vacancy concentration, and photocatalytic activity.

Control over faceting in nanocrystals (NCs) is pivotal for many applications, but most notably when investigating catalytic reactions which occur on the surfaces of nanostructures. Anatase titanium dioxide (TiO(2)) is one of the most studied photocatalysts, but the shape dependence of its activity has not yet been satisfactorily investigated and many questions still remain unanswered. We report the nonaqueous surfactant-assisted synthesis of highly uniform anatase TiO(2) NCs with tailorable morphology in the 10-100 nm size regime, prepared through a seeded growth technique. Introduction of titanium(IV) fluoride (TiF(4)) preferentially exposes the {001} facet of anatase through in situ release of hydrofluoric acid (HF), allowing for the formation of uniform anatase NCs based on the truncated tetragonal bipyramidal geometry. A method is described to engineer the percentage of {001} and {101} facets through the choice of cosurfactant and titanium precursor. X-ray diffraction studies are performed in conjunction with simulation to determine an average NC dimension which correlates with results obtained using electron microscopy. In addition to altering the particle shape, the introduction of TiF(4) into the synthesis results in TiO(2) NCs that are blue in color and display a broad visible/NIR absorbance which peaks in the infrared (λ(max) ≈ 3400 nm). The blue color results from oxygen vacancies formed in the presence of fluorine, as indicated by electron paramagnetic resonance (EPR) and X-ray photoelectron spectroscopy (XPS) studies. The surfactants on the surface of the NCs are removed through a simple ligand exchange procedure, allowing the shape dependence of photocatalytic hydrogen evolution to be studied using monodisperse TiO(2) NCs. Preliminary experiments on the photoreforming of methanol, employed as a model sacrificial agent, on platinized samples resulted in high volumes of evolved hydrogen (up to 2.1 mmol h(-1) g(-1)) under simulated solar illumination. Remarkably, the data suggest that, under our experimental conditions, the {101} facets of anatase are more active than the {001}.

Chain-length-identification strategy in zinc polyphosphate glasses by means of XPS and ToF-SIMS.

The surface chemistry of amorphous zinc polyphosphates of different compositions (ranging from zinc metaphosphate to zinc orthophosphate) has been investigated by means of X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary-ion mass spectroscopy (ToF-SIMS). The identification of the chain length of zinc polyphosphates by XPS was on the basis of the integrated intensity ratio of the bridging (P-O-P) and nonbridging (P = O and P-O-M) oxygen peaks used for fitting the oxygen 1s signal, the shift of the P 2p(3/2) signal towards lower binding energies and the modified Auger parameter towards higher values as the zinc content increases. The discrimination of the polyphosphate chain lengths was also achieved by ToF-SIMS, by comparing the intensities of selected characteristic phosphate fragments. Both techniques appear to be suitable for the investigation of polyphosphate glasses in applications such as tribology, where there is a need to identify the chain length present in the outermost monolayer of the film. Fourier-transform infrared (FT-IR) spectroscopy was used to characterize the bulk compounds. The FT-IR studies showed that long-chain structures linked through P-O-P bonds predominate in the metaphosphate composition, while when the zinc content is increased, the chains become shorter, ultimately being replaced by PO(4) monomers in the orthophosphate composition.