Childbirth simulation to assess cephalopelvic disproportion and chances for failed labor in a French population.

Reducing failed labor and emergency cesarean section (CS) rates is an important goal. A childbirth simulation tool (PREDIBIRTH software and SIM37 platform) that evaluates a 5-min magnetic resonance imaging (MRI) assessment performed at 37 weeks of gestation was developed to enhance the consulting obstetrician's ability to predict the optimal delivery mode. We aimed to determine the potential value of this childbirth simulation tool in facilitating the selection of an optimal delivery mode for both mother and infant. A retrospective cohort study was performed on all patients referred by their obstetricians to our level 2 maternity radiology department between December 15, 2015 and November 15, 2016, to undergo MRI pelvimetry at approximately 37 weeks of gestation. The childbirth simulation software was employed to predict the optimal delivery mode based on the assessment of cephalopelvic disproportion. The prediction was compared with the actual outcome for each case. Including childbirth simulations in the decision-making process had the potential to reduce emergency CSs, inappropriately scheduled CSs, and instrumental vaginal deliveries by up to 30.1%, 20.7%, and 20.0%, respectively. Although the use of the simulation tool might not have affected the overall CS rate, consideration of predicted birthing outcomes has the potential to improve the allocation between scheduled CS and trial of labor. The routine use of childbirth simulation software as a clinical support tool when choosing the optimal delivery mode for singleton pregnancies with a cephalic presentation could reduce the number of emergency CSs, insufficiently justified CSs, and instrumental deliveries.

Using Magnetic Resonance Imaging During Childbirth to Demonstrate Fetal Head Moldability and Brain Compression: Prospective Cohort Study.

BACKGROUND: Childbirth is a physiological process with significant medical risk, given that neurological impairment due to the birthing process can occur at any time. Improvements in risk assessment and anticipatory interventions are constantly needed; however, the birthing process is difficult to assess using simple imaging technology because the maternal bony pelvis and fetal skeleton interfere with visualizing the soft tissues. Magnetic resonance imaging (MRI) is a noninvasive technique with no ionizing radiation that can monitor the biomechanics of the birthing process. However, the effective use of this modality requires teamwork and the implementation of the appropriate safeguards to achieve appropriate safety levels. OBJECTIVE: This study describes a clinically effective and safe method to perform real-time MRI during the birthing process. We reported the experience of our team as part of the IMAGINAITRE study protocol (France), which aimed to better understand the biomechanics of childbirth. METHODS: A total of 27 pregnant women were examined with 3D MRI sequences before going into labor using a 1-Tesla open-field MRI. Of these 27 patients, 7 (26%) subsequently had another set of 3D MRI sequences during the second stage of labor. Volumes of 2D images were transformed into finite element 3D reconstructions. Polygonal meshes for each part of the fetal body were used to study fetal head moldability and brain compression. RESULTS: All 7 observed babies showed a sugarloaf skull deformity and brain compression at the middle strait. The fetus showing the greatest degree of molding and brain shape deformation weighed 4525 g and was born spontaneously but also presented with a low Apgar score. In this case, observable brain shape deformation demonstrated that brain compression had occurred, and it was not necessarily well tolerated by the fetus. Depending on fetal head moldability, these observations suggest that cephalopelvic disproportion can result in either obstructed labor or major fetal head molding with brain compression. CONCLUSIONS: This study suggests the presence of skull moldability as a confounding factor explaining why MRI, even with the best precision to measure radiological landmarks, fails to accurately predict the modality of childbirth. This introduces the fetal head compliance criterion as a way to better understand cephalopelvic disproportion mechanisms in obstetrics. MRI might be the best imaging technology by which to explore all combined aspects of cephalopelvic disproportion and achieve a better understanding of the underlying mechanisms of fetal head molding and moldability.

Three-dimensional magnetic resonance imaging of fetal head molding and brain shape changes during the second stage of labor.

To demonstrate and describe fetal head molding and brain shape changes during delivery, we used three-dimensional (3D) magnetic resonance imaging (MRI) and 3D finite element mesh reconstructions to compare the fetal head between prelabor and the second stage of labor. A total of 27 pregnant women were examined with 3D MRI sequences before going into labor using a 1 Tesla open field MRI. Seven of these patients subsequently had another set of 3D MRI sequences during the second stage of labor. Volumes of 2D images were transformed into finite element 3D reconstructions. Polygonal meshes for each part of the fetal body were used to study fetal head molding and brain shape changes. Varying degrees of fetal head molding were present in the infants of all seven patients studied during the second phase of labor compared with the images acquired before birth. The cranial deformation, however, was no longer observed after birth in five out of the seven newborns, whose post-natal cranial parameters were identical to those measured before delivery. The changing shape of the fetal brain following the molding process and constraints on the brain tissue were observed in all the fetuses. Of the three fetuses presenting the greatest molding of the skull bones and brain shape deformation, two were delivered by cesarean-section (one after a forceps failure and one for engagement default), while the fetus presenting with the greatest skull molding and brain shape deformation was born physiologically. This study demonstrates the value of 3D MRI study with 3D finite element mesh reconstruction during the second stage of labor to reveal how the fetal brain is impacted by the molding of the cranial bones. Fetal head molding was systematically observed when the fetal head was engaged between the superior pelvic strait and the middle brim.

Comparative anatomy on 3-D MRI of the urogenital sinus and the periurethral area before and during the second stage of labor during childbirth.

PURPOSE OF THE STUDY: To describe the observable MRI changes in the urogenital sinus during the second stage of labor and delivery by comparing the changes in the positions of the anatomical structures of the maternal perineum using MRI-based vector 3-D models. MATERIALS AND METHODS: Seven pregnant women underwent 3-D MRI sequences using a Philips 1 T Panorama open MRI during the pre-labor period and during the second stage of labor. A 3-D vector reconstruction platform (BABYPROGRESS, France) enabled the transformation of volumes of 2-D images into finite element meshes. The polygonal meshes labeled with the principal components of the urogenital sinus were used as part of a biomechanical study of the pressure exerted on the perineum during fetal descent. RESULTS: The expansion of the urogenital sinus was observed in all patients. Qualitative stretching was observed toward the rear and bottom of the iliococcygeus, pubococcygeus, puborectalis and obturator internus muscles. Significant length differences were measured along the iliococcygeus and pubococcygeus muscles but not along the tendinous arch of the levator ani or the puborectalis muscle. The inversion of the levator ani muscle curvature was accompanied by the transmission of pressure generated during fetal descent to the pubic muscle insertions and the descent of the tendinous arch of the levator ani. CONCLUSION: Mechanical pressures responsible for the tensioning of the constituent muscles of the urogenital sinus were qualitatively identified during the second stage of labor. MRI-based vector 3-D models allow the quantitative assessment of levator ani muscle stretching during labor, but 2-D MRI is not sufficient for describing perineal expansion. Vector 3-D models from larger scale studies have the potential to aid in the calibration of a realistic simulation based on the consideration of the reaction of each muscular element. These models offer perspectives to enhance our knowledge regarding perineal expansion during childbirth as a risk factor for postpartum perineal defects.