Comparison of torque expression among passive self-ligating brackets with different slot depths: An in vitro study.

INTRODUCTION: The aim of this study was to assess the interaction between a 0.019×0.025-inch (″) stainless steel archwire and two types of passive self-ligating brackets with the same slot height (0.022″) and different slot depths (0.028″ and 0.026″, and to measure the archwire/slot play as well as to compare the torque expression with archwire torsions of 12°, 24°, and 36°. MATERIAL AND METHODS: An experimental device was developed along with a universal testing machine to measure torque expression in two types of brackets with 0.028″ and 0.026″ slot depths. Analysis of variance (ANOVA) and Tukey's test were performed to identify the differences between groups. RESULTS: The 0.026″ slot bracket presented greater archwire/slot play when compared to the 0.028″ bracket. Torque expression with torsions of 24° and 36° were significantly higher in the 0.028″ depth brackets when compared to the 0.026″ depth brackets. CONCLUSION: The 0.022″×0.026″ passive self-ligating brackets attached with a 0.019″×0.025″ stainless steel archwire provided no greater torque control when compared to 0.022″×0.028″ passive self-ligating brackets.

Antibacterial effect, cytotoxicity, and bond strength of a modified dental adhesive containing silver nanoparticles.

This study aimed to evaluate the antibacterial effect, cytotoxicity, and microtensile bond strength of an adhesive system containing silver nanoparticles (NAg). NAg was synthesized and incorporated (500 and 1000 ppm) into Scotchbond Multi-Purpose (SBMP) primer and bond. A microtensile bond test (µTBS) was performed after 24 h and 1 year. The adhesive interface was characterized using a confocal Raman microscope. The antibacterial activity was assessed using agar diffusion and biofilm inhibition assays (S. mutans). MTT assay was used to assess the cytotoxicity of NAg-conditioned culture media on human dental pulp stem cells (hDPSCs). The results were statistically analyzed using analysis of variance and Tukey's tests (α = .01). Incorporating 500 and 1000 ppm of NAg in the SBMP did not affect the µTBS after 24 h (p > 0.05). However, in the 1 year evaluation, 500 ppm presented the highest µTBS values (p < 0.05). The addition of NAg at 500 and 1000 ppm in the primer and bond led to larger inhibition halos and colony-forming units than the control (p < 0.05). For the unpolymerized and polymerized groups, the combination of primer and bond presented the highest cytotoxic effects on hDPSCs (p < 0.05). In conclusion, incorporating 500 or 1000 ppm of NAg into an etch-and-rinse adhesive system led to an antibacterial effect without altering the cytotoxicity. SBMP at 500 ppm presented a higher µTBS at 1 year.

Changes in color and contrast ratio of resin composites after curing and storage in water.

PURPOSE: To verify the color change and contrast ratio of resin composites after curing and after 30 days of storage in water. METHODS: Dentin A2 shades of different light-cured dental resin composites (Vittra APS, FGM, Brazil; Z350 XT, 3M ESPE, EUA; Tetric N-Ceram, Ivoclar Vivadent, Liechtenstein, and Charisma Diamond, Heraeus Kulzer, Germany) were tested. Ten rounded specimens (8 mm × 2 mm) were prepared for each material. Reflectance for all samples was obtained using a spectrophotometer (Minolta CM 3700d, Konica Minolta, Japan) before curing, immediately after curing, and after 30 days of storage in water. The color change (ΔE*lab) and contrast ratio (CR) data were analyzed using a one-way analysis of variance with Tukey's and paired t-tests (α = 1%). RESULTS: For all materials tested, significant color changes were noticeable after curing and after 30 days in water (p < 0.01). Significant changes in the CR values before curing, after curing, and 30 days of storage in water were observed in the resin composites investigated (p < 0.01) except for Z350 (p > 0.01). CONCLUSION: The CR values and color changes after curing and 30 days of storage in water varied depending on the material tested. This study corroborates the clinical practice of curing a small amount of unpolymerized resin composite on the tooth surface to select the desired shade before undertaking esthetic restorative procedures.

Is prolonged bleaching more harmful to dental enamel than daily dietary and hygienic oral habits?

The ultrastructural and mechanical properties of enamel surface were evaluated after prolonged bleaching treatments with 10% carbamide peroxide in the presence or absence of orange juice (erosive challenge) and toothbrushing (abrasive challenge). In total, 145 incisor bovine teeth were used in this study. Twenty-five samples were prepared for the ultrastructural evaluations, and 120 samples were prepared for microhardness and roughness tests. These 120 samples were divided into eight experimental groups (n = 15): G1- artificial saliva; G2- abrasion; G3- erosion; G4- dental bleaching; G5- erosion + abrasion; G6- bleaching + abrasion; G7- bleaching + erosion; and G8- bleaching + erosion + abrasion. All groups were tested at T0 (before treatment), T1 (14 days), T2 (21 days), and T3 (28 days). Two-way analysis of variance for repeated measures and the post hoc Sidak tests (p ≤ 0.05) were used. The roughness evaluation demonstrated an increase in damage for all experimental groups with an increase in the time period. For microhardness, the groups exposed to artificial saliva (AS) and abrasive challenge did not show any differences at any time points, while the other groups showed a decrease in microhardness from T0 to T3. Ultrastructural evaluation showed different surface alterations in response to the treatments. Despite prolonged bleaching periods, the procedure caused lesser enamel surface alterations than exposure to orange juice alone or in combination with brushing.

Post-cure heat treatments influence on mechanical and optical properties of resin composites.

This study evaluated the effect of post-cure heat treatment (PCHT) on the Knoop microhardness (KHN), degree of conversion (DC), color changes, and contrast ratio (CR) of four resin composites (RCs): Z100 (3M ESPE), Z350 XT (3M ESPE), Estelite Omega (Tokuyama) and Empress Direct (Ivoclar Vivadent). Specimens (12 × 1 mm) were prepared for each material (n = 10 / group). After curing, samples were subjected to PCHT for 10 min at 100°C or 170°C. Control group was maintained at room temperature (24°C) for the same time. The DC was analyzed by FT-NIR immediately and 24 h after the PCHT (n = 3 / group). KHN was analyzed 24 h after PCHT (n = 10 / group). According to CIEDE2000 (∆E00), color measurements were obtained immediately after curing, five minutes after PCHT, and after seven days of storage in water, coffee, and red wine. Data were analyzed by One and Two-Way ANOVA (p < 0.05). Z100, Z350, and Estelite Omega showed increases in KHN with increased temperature (p < 0.05). PCHT at 100°C and 170°C led to a higher DC of all RCs (p < 0.05). Initially, the PCHT lead to increased ∆E00 values (p < 0.05), which was decreased after immersion in coffee and wine (p < 0.05). Considering the effect of PCHT and staining solutions, lower color changes were observed in the thermally treated specimens (p < 0.05). Taken collectively, the results suggest the PCHT as an economical and practical alternative to enhance direct RC's properties in direct-indirect and indirect restorations.

Post-cure heat treatments influence on mechanical and optical properties of resin composites

Abstract This study evaluated the effect of post-cure heat treatment (PCHT) on the Knoop microhardness (KHN), degree of conversion (DC), color changes, and contrast ratio (CR) of four resin composites (RCs): Z100 (3M ESPE), Z350 XT (3M ESPE), Estelite Omega (Tokuyama) and Empress Direct (Ivoclar Vivadent). Specimens (12 × 1 mm) were prepared for each material (n = 10 / group). After curing, samples were subjected to PCHT for 10 min at 100°C or 170°C. Control group was maintained at room temperature (24°C) for the same time. The DC was analyzed by FT-NIR immediately and 24 h after the PCHT (n = 3 / group). KHN was analyzed 24 h after PCHT (n = 10 / group). According to CIEDE2000 (∆E00), color measurements were obtained immediately after curing, five minutes after PCHT, and after seven days of storage in water, coffee, and red wine. Data were analyzed by One and Two-Way ANOVA (p < 0.05). Z100, Z350, and Estelite Omega showed increases in KHN with increased temperature (p < 0.05). PCHT at 100°C and 170°C led to a higher DC of all RCs (p < 0.05). Initially, the PCHT lead to increased ∆E00 values (p < 0.05), which was decreased after immersion in coffee and wine (p < 0.05). Considering the effect of PCHT and staining solutions, lower color changes were observed in the thermally treated specimens (p < 0.05). Taken collectively, the results suggest the PCHT as an economical and practical alternative to enhance direct RC's properties in direct-indirect and indirect restorations.

Resumo Este estudo avaliou o efeito do tratamento térmico pós-cura (PCHT) na microdureza Knoop (KHN), grau de conversão (DC), mudanças de cor e razão de contraste (CR) de quatro compósitos resinosos (RCs): Z100 (3M ESPE ), Z350 XT (3M ESPE), Estelite Omega (Tokuyama) e Empress Direct (Ivoclar Vivadent). Corpos de prova (12 × 1 mm) foram preparadas para cada material (n = 10 / grupo). Após a cura, as amostras foram submetidas ao PCHT por 10 min a 100 ou 170° C. O grupo controle foi mantido à temperatura ambiente (24° C) pelo mesmo tempo. O DC foi analisada por FT-NIR imediatamente e 24 h após a PCHT (n = 3 / grupo). KHN foi analisado 24 h após PCHT (n = 10 / grupo). De acordo com o CIEDE2000 (∆E00), as medidas de cor foram obtidas imediatamente após a cura, cinco minutos após a PCHT e após sete dias de armazenamento em água, café e vinho tinto. Os dados foram analisados por ANOVA de um e dois fatores (P < 0,05). Z100, Z350 XT e Estelite Omega mostraram aumentos no KHN com o aumento da temperatura (P < 0,05). PCHT a 100 ° C e 170 ° C levou a uma maior DC de todos os RCs (P < 0,05). Inicialmente, o PCHT levou ao aumento dos valores de ∆E00 (P < 0,05), que diminuiu após a imersão em café e vinho (P < 0,05). Considerando o efeito de PCHT e soluções de coloração, menores mudanças de cor foram observadas nas amostras tratadas termicamente (P < 0,05). Os resultados sugerem o PCHT como uma alternativa econômica e prática para aumentar as propriedades diretas de compósitos resinosos em restaurações diretas-indiretas e indiretas.

Is prolonged bleaching more harmful to dental enamel than daily dietary and hygienic oral habits?

Abstract The ultrastructural and mechanical properties of enamel surface were evaluated after prolonged bleaching treatments with 10% carbamide peroxide in the presence or absence of orange juice (erosive challenge) and toothbrushing (abrasive challenge). In total, 145 incisor bovine teeth were used in this study. Twenty-five samples were prepared for the ultrastructural evaluations, and 120 samples were prepared for microhardness and roughness tests. These 120 samples were divided into eight experimental groups (n = 15): G1- artificial saliva; G2- abrasion; G3- erosion; G4- dental bleaching; G5- erosion + abrasion; G6- bleaching + abrasion; G7- bleaching + erosion; and G8- bleaching + erosion + abrasion. All groups were tested at T0 (before treatment), T1 (14 days), T2 (21 days), and T3 (28 days). Two-way analysis of variance for repeated measures and the post hoc Sidak tests (p ≤ 0.05) were used. The roughness evaluation demonstrated an increase in damage for all experimental groups with an increase in the time period. For microhardness, the groups exposed to artificial saliva (AS) and abrasive challenge did not show any differences at any time points, while the other groups showed a decrease in microhardness from T0 to T3. Ultrastructural evaluation showed different surface alterations in response to the treatments. Despite prolonged bleaching periods, the procedure caused lesser enamel surface alterations than exposure to orange juice alone or in combination with brushing.

Optical parameters and hardness of two maxillofacial elastomers after immersion in different solutions of Brazilian green propolis extract.

STATEMENT OF PROBLEM: Maxillofacial elastomers undergo physical and mechanical degradation with disinfecting solutions. Solutions of Brazilian green propolis extract may be suitable alternatives for infection control of maxillofacial prostheses. However, their effects on the properties of the material are unknown. PURPOSE: The purpose of this in vitro study was to evaluate the effect of disinfection with solutions of Brazilian green propolis extract on the transmittance, translucency parameter, contrast ratio, and hardness of 2 maxillofacial elastomers (MDX4-4210 and MED-4014). MATERIAL AND METHODS: Fifty disk-shaped specimens (3×10 mm) of each elastomer were randomly and equally divided into 4 groups of disinfectant agents and 1 control group: 3 separate groups of 11% green propolis extracts including aqueous (PAQ), glycolic (PGL), and alcoholic (PAL), a 2% chlorhexidine gluconate (CHX) group, and the control group of distilled water. Specimens were subjected to disinfection by immersion 3 times a week for 60 days. Color differences (ΔE values) were calculated with CIELab and CIEDE2000 formulas. Optical parameters and Shore A hardness were determined at 2 time points: at baseline and after the period of specimen disinfection. Data were analyzed by parametric and nonparametric analysis of variance and by multiple-comparison tests (α=.05). RESULTS: The ΔE values of specimens immersed in 11% PAL were not clinically acceptable for either elastomer. Regarding translucency parameter and contrast ratio, the immersion in 11% PAL and 11% PGL resulted in greater opacity and lower translucency of the material. Mean Shore A hardness values were not statistically significantly different at baseline or after 60 days of immersion in the solutions. CONCLUSIONS: The solution of Brazilian green propolis extract tested showed changes in optical parameters. Elastomers immersed in 11% alcoholic green propolis extract showed clinically unacceptable color and translucency changes. All hardness values of the tested elastomers were clinically acceptable after immersion in all tested disinfectant groups.

CO2 laser for dental alumina ceramic framework welding / O laser de CO2 para a soldagem de infraestruturas cerâmicas de alumina

Objective: Despite the increase of all-ceramic prosthesis in dental practice there is no evidence of the possibility of welding these structures if necessary. The objective of this study was to use CO2 laser (λ = 10.6 µm) as a welding agent to fuse dental polycrystalline alumina ceramic. Methods: Ceramic blocks of pre-sintered alumina were sectioned into 20 bars (10.0 x 1.5 x 1.5 mm) and sintered to the final cross section dimension of 1.2 x 1.2mm. The bars were adapted to an LHPG (Laser Heated Pedestal Growth) system device where the bars could be fixed in pairs and have their ends irradiated with CO2 laser to fusion. The ring-shaped laser beam (300 µm thickness) was directed with the aid of mirrors to reach samples' ends. The laser was continuously applied (40 W nominal power, 5 seconds). After welding, the samples were analyzed in stereomicroscope and SEM. A diffraction analysis was carried out with one sample. Results: CO2 laser was able to fuse the ceramic bars, but some of them showed some shape distortion in the fusion zone. The aspect of the fused alumina differed in color and translucency from the original sintered material. SEM evidenced the presence of porosity and voids in the center of the fusion zone. X-ray diffraction pointed to a reduction in crystallite size by two to four times in the welded region of samples. Conclusions: This study points to CO2 laser as a possible welding agent to polycrystalline alumina dental ceramic. Porosity observed in the molten zone gives cause for concern regarding weld resistance. (AU)

Objetivo: Apesar do aumento no número de próteses totalmente cerâmicas na prática clínica, não há evidência da possibilidade de se soldar essas estruturas se necessário. Este estudo testou o laser de CO2 (λ=10.6 µm) como um agente de solda para estruturas cerâmicas de alumina policristalina. Métodos: Blocos cerâmicos de alumina pré-sinterizada foram seccionados na forma de barras (10,0 x 1,5 x 1,5 mm) e sinterizados na dimensão final de 1,2 x 1,2 mm. As barras foram adaptadas a um sistema de crescimento de fibras cerâmicas (LHPG ­ Laser Heated Pedestal Growth) onde as barras foram fixadas em pares e tiveram suas extremidades irradiadas com laser de CO2 até a sua fusão. O feixe de laser foi direcionado com a ajuda de espelhos para atingir as extremidades das barras. O laser foi aplicado de forma contínua (40 W de potência nominal, 5 segundos). Depois da solda, os espécimes foram analisados em estereomicroscopia e MEV. Teste de difração foi conduzido com um espécime. Resutados: O laser de CO2 foi capaz de fundir as barras cerâmicas, mas algumas delas mostraram uma distorção da forma na zona de fusão. O aspecto da alumina soldada diferiu em cor e translucidez do material original. O MEV evidenciou a presença de porosidade no centro da zona de fusão. A difração por raio-x apontou para uma redução no tamanho dos cristalitos de duas a quatro vezes na região da solda. Conclusões: Esse estudo mostrou ser possível usar o laser de CO2 como um agente de solda para uma cerâmica policristalina de alumina. A porosidade observada na zona de fusão traz preocupação quanto à resistência da solda. (AU)

Influence of the Extended Use of Desensitizing Toothpastes on Dentin Bonding, Microhardness and Roughness

Abstract The aim of this study was to evaluate the influence of an extended use of desensitizing toothpastes (DTs) on dentin bonding, microhardness and roughness. One hundred and twenty bovine incisor teeth were randomly divided into four groups: G1, distilled water (WATER); G2, Colgate Total 12 (CT12); G3, Colgate Sensitive Pro-Relief (CSPR); and G4, Sensodyne Repair ?αμπ; Protect (SRP). Dentin surfaces were etched with 17% EDTA and 2 years of simulated tooth brushing (20,000 cycles) was performed on their surfaces. Knoop microhardness, surface roughness and scanning electron microscopy (SEM) were performed before and after the simulated tooth brushing. For microshear bonding test, a 2-step self-etching adhesive system (Clearfil SE Bond) was used and 0.8 mm diameter composite resin (Filtek Z350 XT) cylinders were built. Microshear test was performed with an orthodontic wire and with a crosshead speed of 0.5 mm/min. The data were analyzed for: 1) bond strength (one-way ANOVA), 2) microhardness intra-group (Student's test) and inter-group (one-way ANOVA/Tukey's test) comparisons, 3) roughness intra-group (Student's test/Wilcoxon's test) and inter-group (Kruskal-Wallis/Student-Newman-Keuls test) comparisons. The extended use of both dentifrices (conventional and for sensitive teeth) did not affect the bond strength and produced a significant increase in microhardness and roughness of the dentin, except for the microhardness of the SRP group. The simulated tooth brushing technique with water produced an increase in roughness, without reducing significantly the dentin microhardness.

Resumo O objetivo deste estudo foi avaliar a influência do uso prolongado de dentifrícios dessensibilizantes (DTs) na adesão, microdureza e rugosidade da dentina. Cento e vinte dentes incisivos bovinos foram divididos aleatoriamente em quatro grupos: G1, água destilada (WATER); G2, Colgate Total 12 (CT12); G3, Colgate Sensitive Pro-alívio (CSPR); e G4, Sensodyne Repair ?αμπ; Protect (SRP). As superfícies dentinárias foram condicionadas com EDTA a 17% e foram realizados 2 anos de escovação dental simulada (20.000 ciclos) em suas superfícies. A microdureza Knoop, rugosidade de superfície e microscopia eletrônica de varredura (MEV) foram realizadas antes e após escovação dental simulada. Para o teste de adesão por microcisalhamento, foi aplicado um sistema adesivo auto condicionante de 2 passos (Clearfil SE Bond) e foram construídos cilindros de resina composta (Filtek Z350 XT) de 0,8 mm de diâmetro. O teste de microcisalhamento foi realizado com um fio ortodôntico e com velocidade de 0,5mm/min. Os dados foram analisados para: 1) resistência de união (ANOVA 1 fator), 2) comparações de microdureza intra grupo (teste t de Student) e inter grupo (ANOVA 1 fator / teste de Tukey), 3) comparações de rugosidade intra grupo (teste t de Student / teste de Wilcoxon) e inter grupo (Kruskal Wallis / teste de Student-Newman-Keuls). O uso prolongado de ambos dentifrícios (convencional e para dentes sensíveis) não interferiu na resistência de união e produziu um aumento significativo na microdureza e rugosidade da dentina, exceto para a microdureza do grupo SRP. A técnica de escovação dental simulada com água promoveu aumento na rugosidade, sem reduzir significativamente a microdureza da dentina.

Influence of the Extended Use of Desensitizing Toothpastes on Dentin Bonding, Microhardness and Roughness.

The aim of this study was to evaluate the influence of an extended use of desensitizing toothpastes (DTs) on dentin bonding, microhardness and roughness. One hundred and twenty bovine incisor teeth were randomly divided into four groups: G1, distilled water (WATER); G2, Colgate Total 12 (CT12); G3, Colgate Sensitive Pro-Relief (CSPR); and G4, Sensodyne Repair ?αµπ; Protect (SRP). Dentin surfaces were etched with 17% EDTA and 2 years of simulated tooth brushing (20,000 cycles) was performed on their surfaces. Knoop microhardness, surface roughness and scanning electron microscopy (SEM) were performed before and after the simulated tooth brushing. For microshear bonding test, a 2-step self-etching adhesive system (Clearfil SE Bond) was used and 0.8 mm diameter composite resin (Filtek Z350 XT) cylinders were built. Microshear test was performed with an orthodontic wire and with a crosshead speed of 0.5 mm/min. The data were analyzed for: 1) bond strength (one-way ANOVA), 2) microhardness intra-group (Student's test) and inter-group (one-way ANOVA/Tukey's test) comparisons, 3) roughness intra-group (Student's test/Wilcoxon's test) and inter-group (Kruskal-Wallis/Student-Newman-Keuls test) comparisons. The extended use of both dentifrices (conventional and for sensitive teeth) did not affect the bond strength and produced a significant increase in microhardness and roughness of the dentin, except for the microhardness of the SRP group. The simulated tooth brushing technique with water produced an increase in roughness, without reducing significantly the dentin microhardness.

Effect of Glaze Cooling Rate on Mechanical Properties of Conventional and Pressed Porcelain on Zirconia.

The aim of this study was to characterize a conventional and a pressed porcelain for zirconia core as to biaxial flexural strength (BFS), apparent fracture toughness (FT) and microstructure composition, and to investigate the effect of glaze cooling rate on the BFS of the zirconia/porcelain bilayers. Monolayers of conventional porcelain Vita VM9 and pressed porcelain Vita PM9 (n=15) (12 mm diameter x 1.2 mm thick) were prepared for the BFS test (MPa). Apparent fracture toughness (MPa.m1/2) was measured by indentation technique (n=15). t-Student test was performed for statistical analysis. Scanning electron microscopy and x-ray diffraction were used to analyze the porcelain's microstructure. For the BFS of bilayers, zirconia discs (12 mm diameter x 1 mm thick) (Vita In-Ceram YZ) were veneered with the two porcelains (1 mm thick). After the glaze firing simulation, the specimens were submitted to fast or slow cooling (n=15). Apparent fracture toughness (MPa.m1/2) was measured on the porcelain surface of bilayers (n=15) and residual stress was calculated. Two-way ANOVA (porcelain and cooling method) was used for the bilayer analysis (a=0.05). Vita PM9 monolayer exhibited significantly higher BFS (p<0.01), but there was no significant difference (p=0.41) in the FT between the porcelains. For bilayer specimens, the two-way ANOVA for BFS was significant for the porcelain variable only (p<0.01) better for Vita PM9/zirconia. Two-way ANOVA for the FT for the bilayers was not significant for any variable. All groups showed compressive residual stresses. The pressed porcelain seems to be mechanically more effective for zirconia veneering.

Effect of Glaze Cooling Rate on Mechanical Properties of Conventional and Pressed Porcelain on Zirconia

Abstract The aim of this study was to characterize a conventional and a pressed porcelain for zirconia core as to biaxial flexural strength (BFS), apparent fracture toughness (FT) and microstructure composition, and to investigate the effect of glaze cooling rate on the BFS of the zirconia/porcelain bilayers. Monolayers of conventional porcelain Vita VM9 and pressed porcelain Vita PM9 (n=15) (12 mm diameter x 1.2 mm thick) were prepared for the BFS test (MPa). Apparent fracture toughness (MPa.m1/2) was measured by indentation technique (n=15). t-Student test was performed for statistical analysis. Scanning electron microscopy and x-ray diffraction were used to analyze the porcelain's microstructure. For the BFS of bilayers, zirconia discs (12 mm diameter x 1 mm thick) (Vita In-Ceram YZ) were veneered with the two porcelains (1 mm thick). After the glaze firing simulation, the specimens were submitted to fast or slow cooling (n=15). Apparent fracture toughness (MPa.m1/2) was measured on the porcelain surface of bilayers (n=15) and residual stress was calculated. Two-way ANOVA (porcelain and cooling method) was used for the bilayer analysis (a=0.05). Vita PM9 monolayer exhibited significantly higher BFS (p<0.01), but there was no significant difference (p=0.41) in the FT between the porcelains. For bilayer specimens, the two-way ANOVA for BFS was significant for the porcelain variable only (p<0.01) better for Vita PM9/zirconia. Two-way ANOVA for the FT for the bilayers was not significant for any variable. All groups showed compressive residual stresses. The pressed porcelain seems to be mechanically more effective for zirconia veneering.

Resumo Este estudo teve como objetivo caracterizar uma porcelana convencional e uma prensada indicadas para infraestrutura de zircônia em termos de resistência à flexão biaxial (RFB), tenacidade à fratura aparente (TF) e composição microestrutural, e investigar o efeito da taxa de resfriamento do ciclo de glaze na RFB de espécimes bicamada de zircônia/porcelana. Espécimes monocamada de porcelana convencional Vita VM9 e porcelana prensada Vita PM9 (n=15) (12 mm de diâmetro x 1,2 mm de espessura) foram preparados para o ensaio de RFB (MPa). Tenacidade à fratura aparente (MPa.m1/2) foi mensurada pela técnica da indentação (n=15). O teste de t-Student foi aplicado para as análises estatísticas. Microscopia eletrônica de varredura e difração de raios-X foram utilizadas para análise microestrutural da porcelana. Para o ensaio de RFB nos bicamadas, discos de zircônia (12 mm de diâmetro x 1 mm de espessura) (Vita In-Ceram YZ) foram recobertos com as duas porcelanas (1 mm de espessura). Após a simulação da queima de glaze, os espécimes foram submetidos ao método de resfriamento rápido ou lento (n=15). A tenacidade à fratura aparente (MPa.m1/2) foi mensurado na superfície da porcelana dos bicamadas (n=15) e o estresse residual foi calculado. Foi utilizado ANOVA a dois fatores (porcelana e método de resfriamento) para análise estatística dos espécimes bicamada (a=0,05). Monocamadas de Vita PM9 exibiram valores de resistência à flexão biaxial significativamente maiores (p<0,01), mas não houve diferença estatística (p=0,41) em relação à TF entre as porcelanas. Para os espécimes bicamada, ANOVA a dois fatores para RFB foi significante apenas para a variável porcelana (p<0,01), com superioridade para Vita PM9/zircônia. ANOVA a dois fatores para TF dos espécimes bicamadas não apresentou significância para nenhuma variável. Todos os grupos apresentaram estresse residual de compressão. Porcelanas prensadas parecem ser mecanicamente mais efetivas para recobrimento de zircônia.

Influence of prolonged use of desensitizing dentifrices on dentin bond strength of self-etching adhesive system / Influencia del uso prolongado de pasta dentífrica desensibilizante en la fuerza de unión de la dentina de un sistema adhesivo autocondicionante

Dentin hypersensitivity is a relatively common clinical condition, which affects a large part of the world's population. The objective of this study was to evaluate the influence of previous and prolonged treatment with desensitizing dentifrices (DD) on bond strength to dentin, promoted by a self-etching adhesive system. Seventy non-carious bovine incisors were used, and divided into five groups (n= 14), according to the desensitizing toothpaste used, such as, G1: distilled water (WATER) (control); G2: Colgate Total 12 (CT12) (control); G3: Colgate Sensitive Pro-Relief (CSPR); G4: Sensodyne Rapid Relief (SRR); G5: Sensodyne Repair & Protect (SRP). Teeth had their buccal surfaces flattened until the exposure of dentin, and fragments of 4x4x2 mm were obtained. Fragments were included in polyvinyl chloride (PVC) cylinders and exposed to 17 % EDTA for 1 min. Subsequently, specimens were submitted to 20 000 cycles of simulated dental toothbrushing. After 24 h in artificial saliva, specimens were hybridized (Clearfil SE Bond ­ Kuraray), as well as resin composite cylinders built on dentin surfaces. Samples were stored in distilled water, at 37 C for 24 h, and the shear bond strength was determined. The highest bond strength (MPa) value was seen in CT12 group (4.39), and the lowest one in CSPR group (3.34). Data were statistically analyzed by 1-way ANOVA (ð= 0.05), and results showed that there were no significant differences (p= 0.5986) considering the DD factor. The predominant fracture pattern was cohesive on dentin. The previous and prolonged use of different DD did not affect dentin bond strength promoted by a self-etching adhesive system.

La hipersensibilidad dentinaria es una condición clínica relativamente común, que afecta a una gran parte de la población mundial. El objetivo fue evaluar la influencia del tratamiento previo y prolongado con dentífricos desensibilizantes (DD) en fuerza de adhesión a la dentina, que promueve un sistema adhesivo de autograbado. Se utilizaron 70 incisivos bovinos no cariados, y se dividieron en cinco grupos (n= 14), de acuerdo con la pasta de dientes desensibilizante utilizada: G1: agua destilada (agua) (control), G2: Colgate Total 12 (CT12) (control), G3: Colgate Sensitive Pro-Alivio (CSPR), G4: Sensodyne Rápido Alivio (SRR) y G5: Sensodyne Repair & Protect (SRP). Los dientes tenían sus superficies bucales aplanadas hasta la exposición de la dentina, y se obtuvieron fragmentos de 4x4x2 mm. Los fragmentos se incluyeron en cilindros de cloruro de polivinilo y se expusieron a 17 % de EDTA durante un 1 min. Después, las muestras se sometieron a 20 000 ciclos de cepillado dental simulado. Después de 24 h en saliva artificial, las muestras se hibridaron (Clearfil SE Bond - Kuraray), y cilindros de resina compuesta fueron construidos sobre superficies de dentina. Las muestras se almacenaron en agua destilada, a 37 °C durante 24 h y luego se determinó la resistencia al cizallamiento. El mayor valor de resistencia a la unión (MPa) se observó en el grupo CT12 (4,39), y el menor en el grupo CSPR (3,34). Los datos fueron analizados estadísticamente mediante ANOVA de un factor 1 (ð= 0,05), y los resultados no mostraron diferencias significativas (p= 0,5986) teniendo en cuenta el factor de los DD. El patrón de fractura predominante sobre la dentina fue el cohesivo. El uso previo y prolongado de diferente DD no afectó resistencia de unión a la dentina promovido por un sistema adhesivo de autograbado.

Relationship between toothpastes properties and patient-reported discomfort: crossover study.

OBJECTIVES: This study aims to correlate patient-reported reactions with in vitro analyses of the pH, abrasive quality, and cytotoxicity of four toothpastes. MATERIALS AND METHODS: One hundred twenty-one patients received non-identified samples of toothpaste to be used for 6 days and answered a questionnaire about their sensations. In vitro analysis: the pH of toothpastes was measured with a pH meter. The abrasivity of toothpastes was evaluated against composite resin specimens (n = 10). A toothbrushing machine was used to simulate wear, which was indirectly measured by mass loss using a scale. Cell culture media conditioned with toothpaste were used to assess the cytotoxicity. Confluent cells were kept in contact with the conditioned media or control for 24 h. The cell viability was measured using the 3-(bromide, 4,5-dimethylthiazol-2yl)-2,5-diphenyltetrazolium (MTT)-reduction assay. The obtained data on the pH, weight loss, and cell viability were compared by ANOVA/Tukey's tests (p < 0.05). RESULTS: With the exception of the bleaching effect paste, the Oral B® paste produced the highest frequencies of irritation reports, tooth sensitivity, taste discomfort, and texture discomfort in the clinical study; patients also reported rougher teeth, soft tissue peeling, dry mouth, thrush, tingling, and taste changes in response to this paste. The in vitro analysis demonstrated that Oral B® had the lowest pH, the highest abrasivity, and produced the lowest cell viability (p < 0.01). CONCLUSION: Results suggest that low pH toothpastes that are highly abrasive and cytotoxic may cause undesirable reactions in patients. CLINICAL RELEVANCE: Toothpaste's properties should be well known for indication to patient therefore minimizing discomfort reports.

Evaluation of the mechanical properties of acetic-cure silicone with the addition of magnesium silicate / Avaliação das propriedades mecânicas de silicone de cura acética, com a adição de silicato de magnésio

Current study evaluates the mechanical properties (tensile and tear strength) of an acetic- cure silicone with the addition of 10 or 20% vol. magnesium silicate. Magnesium silicate was added to the silicone at concentrations of 10 (MS-10) and 20% (MS-20) volume, followed by the analysis of tensile strength, maximal elongation during tensile and tear strength. Results were compared to control group of silicone without additives (CG). Mean rates were determined and compared by analysis of variance and Tukey's test (p < 0.05). Control group had the greatest elongation when subjected to tensile strength (650%), whereas the MS-10 group statistically showed a better tensile strength (8.8 MPa) when compared to CG (7.5 MPa) and MS -20 (7.5 MPa) groups. Both magnesium silicate groups exhibited statistically similar tear strength, whereas MS-20 group demonstrated statistically greater tear strength. The addition of 10% magnesium silicate increased tensile strength, but tear strength and elongation were similar to control. The addition of 20% magnesium silicate did not affect tensile but increased tear strength.

O objetivo deste estudo foi avaliar as propriedades mecânicas (resistência à tração e ao rasgamento) de um silicone de cura acética com adição de 10 ou 20% em volume de silicato de magnésio. O silicato de magnésio foi adicionado ao silicone em concentrações de 10 (MS-10) e 20% (MS-20), em volume, avaliado por análise de resistência à tração, deformação máxima em tração e resistência ao rasgamento. Os resultados foram comparados com um grupo de controle sem aditivos de silicone (GC). Os valores médios foram determinados e comparados através de análise de variância e teste de Tukey (p < 0,05). O grupo de controle apresentou o maior alongamento quando submetido à tensão (650%). O grupo MS-10 exibiu estatisticamente melhor resistência à tração (8,8 MPa) em relação ao GC (7,5 MPa) e MS-20 (7,5 MPa) grupos. Ambos os grupos de silicato de magnésio exibiram médias de resistência ao rasgamento estatisticamente semelhantes, enquanto que o grupo de EM-20 demonstrou estatisticamente maior resistência ao rasgamento em comparação com o grupo de controle. A adição de 10% de silicato de magnésio em volume propiciou maiores valores de resistência ao rasgamento e resistência à tração. A adição de 20% de silicato de magnésio não afetou a resistência à tração, mas produziu aumento na resistência ao rasgamento.

Surface treatment of dental porcelain: CO2 laser as an alternative to oven glaze.

This work tested continuous CO2 laser as a surface treatment to dental porcelain and compared it to oven glaze (auto-glaze) by means of roughness and color parameters. Three commercial veneering porcelains with different crystalline content were tested: VM7, VM9, and VM13. Porcelain discs (3.5 × 2.0 mm, diameter × height) were sintered and had one side ground by a diamond bur (45 µm) simulating a chairside adjustment in a clinical office. Specimens (n = 7) were divided into the following groups: C--control (no treatment), G--auto-glaze (oven), and L--surface continuous irradiation with CO2 laser (Gem Laser, Coherent; λ = 10.6 µm). Laser was tested in three exposure times (3, 4, or 5 min) and two irradiances (45 and 50 W/cm(2)). Roughness parameters (Ra, Rz, and Rpm/Rz) were measured using a rugosimeter (Surftest 301, Mitutoyo). Color differences (ΔE) between the G and L groups were calculated (VITA Easyshade); ΔE values up to 3.3 were considered as not perceivable. A surface analysis was conducted by stereomicroscopy (Olympus SZ61) and SEM (Stereoscan 440, LEO). Crystalline content of specimens from groups C and L (50 W/cm(2), 5 min) was assessed by X-ray diffraction and then compared. Surface roughness (Ra and Rz) observed for laser-irradiated groups was similar to G for all studied porcelains. Rpm/Rz ratios were near 1.0 for all groups that indicated a sharp ridge profile for all specimens. Only one laser condition studied (50 W/cm(2), 3 min) from VM7 porcelain resulted in color difference (ΔE = 3.5) to G. Specimens irradiated with 50 W/cm(2) for 5 min presented the smoother surface observed by SEM, comparable to G. X-ray diffraction data revealed an increase in leucite crystallite size for VM9 and VM13 porcelains after laser treatment. Regarding roughness, continuous CO2 laser applied on porcelain surface was as effective as conventional oven auto-glaze.

Bond strenght of zirconia submitted to different surface treatments

To evaluate the shear bond strength of a recent adhesive system used in the cementation of zirconia.Material and Methods:Overall, 72 zirconia specimens (Zirconzhan) were divided and randomized into 3 groups according to the type of surface treatment: G1 no treatment + adhesive system; G2 blasted with aluminum oxide + adhesive system and G3 tribochemical treatment (Rocatec Plus) + adhesive system. Half of each group (n = 12) had bond strength evaluated on two occasions: 24 hours after cementation, kept stored in distilled water at 37 ° C without thermal cycling, and after thermal cycling (5000 cycles, 5°C-55°C). Data were analyzed by ANOVA with Tukey's post-test (α≤0.05).Results:At first moment, G1 and G3 showed higher bond strength (8.64 ± 3.43 MPa and 6.55 ± 2.27 MPa) compared to G2, with no statistically significant difference between them. After thermal cycling, G3 showed higher bond strength (7.70 ± 1.82 MPa).Conclusion:Initially, only the adhesive system promoted higher bond strength, but after thermal cycling,bond strength decreased. The best treatment to promote high bond strength to zirconia is to associate tribochemical treatment with the adhesive system; most failures observed after thermal cycling were mixed and cohesive, showing a mechanical imbrication of the adhesive system, suggesting that there is no chemical bond; and the surface of the group with greater bond strength after thermal cycling showed more surface irregularities compared to the other groups...

Effect of lingual enamel sandblasting with aluminum oxide of different particle sizes in combination with phosphoric acid etching on indirect bonding of lingual brackets.

OBJECTIVE: To compare bond strength and bond failure location of lingual brackets indirectly bonded after lingual enamel sandblasting with 27-, 50-, and 90-µm aluminum oxide particles followed by 37% phosphoric acid etching. MATERIAL AND METHODS: Eighty maxillary premolars were randomly divided into four equal groups according to the method of lingual enamel surface conditioning: Group 1 (control) was etched with 37% phosphoric acid, and group 2, group 3, and group 4 were sandblasted with 27-, 50-, and 90-µm aluminum oxide particles, respectively, prior to acid etching. Lingual brackets were indirectly bonded using the same protocol and adhesive (Sondhi) in all groups. The maximum shear bond strength required to debond the brackets was measured using a testing machine, and the bond failure location was classified according to the adhesive remnant index (ARI). Analysis of variance was used to compare the mean bond strength between groups. The differences between ARI scores were evaluated using the Kruskal-Wallis test. RESULTS: There were no statistically significant differences in mean shear bond strength or ARI scores between the four enamel-conditioning procedures. CONCLUSION: Lingual enamel sandblasting using different particle sizes of aluminum oxide prior to phosphoric acid etching did not increase the shear bond strength of indirectly bonded brackets and did not affect the amount of adhesive remnant on the enamel.

Effect of adhesion boosters on indirect bracket bonding.

OBJECTIVE: To determine the influence of two adhesion boosters on shear bond strength and on the bond failure location of indirectly bonded brackets. MATERIALS AND METHODS: Sixty bovine incisors were randomly divided into three groups (n = 20), and their buccal faces were etched using 37% phosphoric acid. In group 1 (control), brackets were indirectly bonded using only Sondhi adhesive. In groups 2 and 3, the adhesion boosters Enhance Adhesion Booster and Assure Universal Bonding Resin, respectively, were applied before bonding with Sondhi. Maximum bond strength was measured with a universal testing machine, and the location of bond failure was evaluated using the Adhesive Remnant Index (ARI). One-way analysis of variance followed by the Tukey test (P < .05) was used to compare the shear bond strength among groups, and the differences in ARI scores were evaluated using the Kruskal-Wallis test (P < .05). The Pearson correlation coefficient was calculated to determine whether there was any correlation between bond strength and ARI scores. RESULTS: The mean shear bond strength in group 3 was significantly higher (P < .01) than in the other groups. Evaluation of the locations of bond failure revealed differences (P < .05) among the three groups. There was a moderate correlation between bond strength and ARI scores within group 3 (r  =  0.5860, P < .01). CONCLUSION: In vitro shear bond strength was acceptable in all groups. The use of the Assure adhesion booster significantly increased both the shear bond strength of indirectly bonded brackets and the amount of adhesive that remained on the enamel after bracket debonding.