Enhancing Water Treatment Performance of Porous Polysulfone Hollow Fiber Membranes through Atomic Layer Deposition.

Polysulfone (PSF) is one of the most used polymers for water treatment membranes, but its intrinsic hydrophobicity can be detrimental to the membranes' performances. By modifying a membrane's surface, it is possible to adapt its physicochemical properties and thus tune the membrane's hydrophilicity or porosity, which can achieve improved permeability and antifouling efficiency. Atomic layer deposition (ALD) stands as a distinctive technology offering exceedingly even and uniform layers of coatings, like oxides that cover the surfaces of objects with three-dimensional (3D) shapes, porous structures, and particles. In the context of this study, the focus was on titanium dioxide (TiO2), zinc oxide (ZnO), and alumina (Al2O3), which were deposited on polysulfone hollow fiber (HF) membranes via ALD using TiCl4, diethyl zinc (DEZ), and trimethylamine (TMA), respectively, and H2O as precursors. The morphology and mechanical properties of membranes were changed without damaging their performances. The deposition was confirmed mainly by energy-dispersive X-ray spectroscopy (EDX). All depositions offered great performances with a maintained permeability and BSA retention and a 20 to 40° lower water contact angle (WCA) than the raw PSF HF membrane. The deposition of TiO2 offered the best results, showing an enhancement of 50% for the water permeability and 20% for the fouling resistance of the PSF HF membranes.

CaCu3Ti4O12 Perovskite Materials for Advanced Oxidation Processes for Water Treatment.

The many pollutants detected in water represent a global environmental issue. Emerging and persistent organic pollutants are particularly difficult to remove using traditional treatment methods. Electro-oxidation and sulfate-radical-based advanced oxidation processes are innovative removal methods for these contaminants. These approaches rely on the generation of hydroxyl and sulfate radicals during electro-oxidation and sulfate activation, respectively. In addition, hybrid activation, in which these methods are combined, is interesting because of the synergistic effect of hydroxyl and sulfate radicals. Hybrid activation effectiveness in pollutant removal can be influenced by various factors, particularly the materials used for the anode. This review focuses on various organic pollutants. However, it focuses more on pharmaceutical pollutants, particularly paracetamol, as this is the most frequently detected emerging pollutant. It then discusses electro-oxidation, photocatalysis and sulfate radicals, highlighting their unique advantages and their performance for water treatment. It focuses on perovskite oxides as an anode material, with a particular interest in calcium copper titanate (CCTO), due to its unique properties. The review describes different CCTO synthesis techniques, modifications, and applications for water remediation.

Design and Manufacturing of Si-Based Non-Oxide Cellular Ceramic Structures through Indirect 3D Printing.

Additive manufacturing of Polymer-Derived Ceramics (PDCs) is regarded as a disruptive fabrication process that includes several technologies such as light curing and ink writing. However, 3D printing based on material extrusion is still not fully explored. Here, an indirect 3D printing approach combining Fused Deposition Modeling (FDM) and replica process is demonstrated as a simple and low-cost approach to deliver complex near-net-shaped cellular Si-based non-oxide ceramic architectures while preserving the structure. 3D-Printed honeycomb polylactic acid (PLA) lattices were dip-coated with two preceramic polymers (polyvinylsilazane and allylhydridopolycarbosilane) and then converted by pyrolysis respectively into SiCN and SiC ceramics. All the steps of the process (printing resolution and surface finishing, cross-linking, dip-coating, drying and pyrolysis) were optimized and controlled. Despite some internal and surface defects observed by topography, 3D-printed materials exhibited a retention of the highly porous honeycomb shape after pyrolysis. Weight loss, volume shrinkage, roughness and microstructural evolution with high annealing temperatures are discussed. Our results show that the sacrificial mold-assisted 3D printing is a suitable rapid approach for producing customizable lightweight highly stable Si-based 3D non-oxide ceramics.

Improved electrochemical conversion of CO2 to multicarbon products by using molecular doping.

The conversion of CO2 into desirable multicarbon products via the electrochemical reduction reaction holds promise to achieve a circular carbon economy. Here, we report a strategy in which we modify the surface of bimetallic silver-copper catalyst with aromatic heterocycles such as thiadiazole and triazole derivatives to increase the conversion of CO2 into hydrocarbon molecules. By combining operando Raman and X-ray absorption spectroscopy with electrocatalytic measurements and analysis of the reaction products, we identified that the electron withdrawing nature of functional groups orients the reaction pathway towards the production of C2+ species (ethanol and ethylene) and enhances the reaction rate on the surface of the catalyst by adjusting the electronic state of surface copper atoms. As a result, we achieve a high Faradaic efficiency for the C2+ formation of ≈80% and full-cell energy efficiency of 20.3% with a specific current density of 261.4 mA cm-2 for C2+ products.

Fabrication of 3D printed antimicrobial polycaprolactone scaffolds for tissue engineering applications.

Synthetic polymers are widely employed for bone tissue engineering due to their tunable physical properties and biocompatibility. Inherently, most of these polymers display poor antimicrobial properties. Infection at the site of implantation is a major cause for failure or delay in bone healing process and the development of antimicrobial polymers is highly desired. In this study, silver nanoparticles (AgNps) were synthesized in polycaprolactone (PCL) solution by in-situ reduction and further extruded into PCL/AgNps filaments. Customized 3D structures were fabricated using the PCL/AgNps filaments through 3D printing technique. As demonstrated by scanning electron microscopy, the 3D printed scaffolds exhibited interconnected porous structures. Furthermore, X-ray photoelectron spectroscopy analysis revealed the reduction of silver ions. Transmission electron microscopy along with energy-dispersive X-ray spectroscopy analysis confirmed the formation of silver nanoparticles throughout the PCL matrix. In vitro enzymatic degradation studies showed that the PCL/AgNps scaffolds displayed 80% degradation in 20 days. The scaffolds were cytocompatible, as assessed using hFOB cells and their antibacterial activity was demonstrated on Escherichia coli. Due to their interconnected porous structure, mechanical and antibacterial properties, these cytocompatible multifunctional 3D printed PCL/AgNps scaffolds appear highly suitable for bone tissue engineering.

Investigation of polymer-derived Si-(B)-C-N ceramic/reduced graphene oxide composite systems as active catalysts towards the hydrogen evolution reaction.

Hydrogen Evolution Reaction (HER) is an attractive technology for chemical conversion of energy. Replacement of platinum with inexpensive and stable electrocatalysts remains a major bottleneck hampering large-scale hydrogen production by using clean and renewable energy sources. Here, we report electrocatalytically active and ultra-stable Polymer-Derived Ceramics towards HER. We successfully prepared ultrathin silicon and carbon (Si-C) based ceramic systems supported on electrically conducting 2D reduced graphene oxide (rGO) nanosheets with promising HER activity by varying the nature and the composition of the ceramic with the inclusion of nitrogen, boron and oxygen. Our results suggest that oxygen-enriched Si-B-C-N/rGO composites (O-SiBCN/rGO) display the strongest catalytic activity leading to an onset potential and a Tafel slope of - 340 mV and ~ 120 mV dec-1 respectively. O-SiBCN/rGO electrodes display stability over 170 h with minimal increase of 14% of the overpotential compared to ~ 1700% for commercial platinum nanoparticles. Our study provides new insights on the performance of ceramics as affordable and robust HER catalysts calling for further exploration of the electrocatalytic activity of such unconventional materials.

Porous Gelatin Membranes Obtained from Pickering Emulsions Stabilized with h-BNNS: Application for Polyelectrolyte-Enhanced Ultrafiltration.

In recent years, numerous studies have been conducted to develop biopolymer-based membranes, highlighting the challenges to prepare porous structures with control porosity. In this paper an innovative method that relies on the generation of Pickering emulsions was developed to prepare porous membranes from gelatin for filtration purpose. Hexagonal boron nitride nanosheets (h-BNNS) were used to stabilize micro-droplets of castor oil in a continuous homogeneous gelatin solution. Two steps in the membrane preparation process strongly influenced the porous structure. Specifically, the duration of the drying time after emulsion casting and the duration of the cross-linking step affected membrane pore size, hydrophobicity, water swelling, and water permeability. By controlling these two steps, membranes could be designed with pore size between 0.39 and 1.60 µm and display pure water permeability between 150 and 506 L h-1 m-2 bar-1. These membranes have been tested for complexation-ultrafiltration experiments in which iron ions were removed from aqueous solutions with/without poly (acrylic acid) (PAA). Without PAA, the removal of free iron (II) ions was low (not more than 14%). The addition of PAA (200 ppm) allowed obtaining high removal rates (97%) at pH ≥ 5 with 3 bars of transmembrane pressure.

Boron Nitride Based Nanobiocomposites: Design by 3D Printing for Bone Tissue Engineering.

Here, we produced a synthetic polymer having adequate biocompatibility, biodegradability, and bioresorbability, as well as mechanical properties for applications in bone tissue engineering. We used the fused deposition modeling (FDM) based 3D printing approach in order to produce biomimetic biodegradable scaffolds made of polylactic acid (PLA). We strengthened these scaffolds by addition of exfoliated boron nitride (EBN) as filler. We demonstrated the presence of EBN by physicochemical analysis using Raman spectroscopy and X-ray diffraction (XRD). Using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), we found that EBN incorporation did not influence the transition temperature, but reduced the polymer crystallinity. Scanning electron microscopy for morphology evaluation showed a mean scaffold pore size of 500 µm. EBN incorporation did not affect the scaffold mechanical properties (tensile test), but modified the surface roughness. Moreover, contact angle quantification indicated that the surface of PLA/EBN scaffolds was hydrophilic and that of PLA scaffolds hydrophobic. Finally, the results of the cytotoxicity, cell attachment, and proliferation experiments using MG-63 and MC3T3 cells indicated that PLA scaffolds filled with EBN were nontoxic and compatible with osteoblastic cells and also promoted the scaffold mineralization by MG-63 cells. Altogether, our results suggest that this 3D printed nanocomposite scaffold is suitable for tissue engineering.

Enhancement of Podocyte Attachment on Polyacrylamide Hydrogels with Gelatin-Based Polymers.

Biological activities of cells such as survival and differentiation processes are mainly maintained by a specific extracellular matrix (ECM). Hydrogels have recently been employed successfully in tissue engineering applications. In particular, scaffolds made of gelatin methacrylate-based hydrogels (GelMA) showed great potential due to their biocompatibility, biofunctionality, and low mechanical strength. The development of a hydrogel having tunable and appropriate mechanical properties as well as chemical and biological cues was the aim of this work. A synthetic and biological hybrid hydrogel was developed to mimic the biological and mechanical properties of native ECM. A combination of gelatin methacrylate and acrylamide (GelMA-AAm)-based hydrogels was studied, and it showed tunable mechanical properties upon changing the polymer concentrations. Different GelMA-AAm samples were prepared and studied by varying the concentrations of GelMA and AAm (AAm2.5% + GelMA3%, AAm5% + GelMA3%, and AAm5% + GelMA5%). The swelling behavior, biodegradability, physicochemical and mechanical properties of GelMA-AAm were also characterized. The results showed a variation of swelling capability and a tunable elasticity ranging from 4.03 to 24.98 kPa depending on polymer concentrations. Moreover, the podocyte cell morphology, cytoskeleton reorganization and differentiation were evaluated as a function of GelMA-AAm mechanical properties. We concluded that the AAm2.5% + GelMA3% hydrogel sample having an elasticity of 4.03 kPa can mimic the native kidney glomerular basement membrane (GBM) elasticity and allow podocyte cell attachment without the functionalization of the gel surface with adhesion proteins compared to synthetic hydrogels (PAAm). This work will further enhance the knowledge of the behavior of podocyte cells to understand their biological properties in both healthy and diseased states.

Composites Based on Nanoparticle and Pan Electrospun Nanofiber Membranes for Air Filtration and Bacterial Removal.

Often, solid matter is separated from particle-laden flow streams using electrospun filters due to their high specific surface area, good ability to capture aerial particulate matter, and low material costs. Moreover, electrospinning allows incorporating nanoparticles to improve the filter's air filtration efficiency and bacterial removal. Therefore, a new, improved polyacrylonitrile (PAN) nanofibers membrane that could be used to remove air pollutants and also with antibacterial activity was developed. We engineered three different filters that are characterized by the different particles embedded in the PAN nanofibers: titanium dioxide (TiO2), zinc oxide (ZnO), and silver (Ag). Then, their filtration performance was assessed by quantifying the filtration of sodium chloride (NaCl) aerosol particles of 9 to 300 nm in diameter using a scanning mobility particle sizer. The TiO2_F filter displayed the smallest fiber diameter and the highest filtration efficiency (≈100%). Conversely, the Ag_F filter showed the highest quality factor (≈0.06 Pa-1) because of the lower air pressure drop. The resulting Ag_F nanofibers displayed a very good antibacterial activity using an Escherichia coli suspension (108 CFU/mL). Moreover, the quality factor of these membranes was higher than that of the commercially available nanofiber membrane for air filtration.

Enhanced visible light photocatalysis by TiO2-BN enabled electrospinning of nanofibers for pharmaceutical degradation and wastewater treatment.

Boron nitride (BN) nanosheets are promising support materials for catalysts. A series of TiO2-BN enabled electrospun nanofibers were synthesized for the photocatalytic treatment of ibuprofen and secondary wastewater effluent under visible light. X-ray photoelectron spectroscopy confirmed the existence of B-O-Ti bonds between the BN nanosheets and TiO2 nanofibers, resulting in energy rearrangement, narrowed band gaps, and enhanced light utilization efficiency of the TiO2-BN nanocomposites in the visible light spectrum. Transient photocurrent measurements revealed that the BN enhanced the transport of photogenerated holes from the bulk TiO2 nanofibers to its surface, resulting in more efficient separation and less recombination of the charge carriers. A kinetic study of ibuprofen degradation indicated the enhanced photocatalytic performance of TiO2-BN catalysts with a higher BN content in the nanocomposites. The kinetic rate constant of the TiO2-10% BN catalysts was 10 times higher than that of the pure TiO2 nanofibers. The degradation of organic contaminants in wastewater followed the same trend as ibuprofen and improved with increasing BN content. The stability of the TiO2-BN nanocomposites as an effective solar photocatalyst was demonstrated by multiple cycles of wastewater treatment. The results proved that TiO2-BN is an appealing photocatalyst under visible light.

On the Use of MOFs and ALD Layers as Nanomembranes for the Enhancement of Gas Sensors Selectivity.

Improving the selectivity of gas sensors is crucial for their further development. One effective route to enhance this key property of sensors is the use of selective nanomembrane materials. This work aims to present how metal-organic frameworks (MOFs) and thin films prepared by atomic layer deposition (ALD) can be applied as nanomembranes to separate different gases, and hence improve the selectivity of gas sensing devices. First, the fundamentals of the mechanisms and configuration of gas sensors will be given. A selected list of studies will then be presented to illustrate how MOFs and ALD materials can be implemented as nanomembranes and how they can be implemented to improve the operational performance of gas sensing devices. This review comprehensively shows the benefits of these novel selective nanomaterials and opens prospects for the sensing community.

Enhanced sieving from exfoliated MoS2 membranes via covalent functionalization.

Nanolaminate membranes made of two-dimensional materials such as graphene oxide are promising candidates for molecular sieving via size-limited diffusion in the two-dimensional capillaries, but high hydrophilicity makes these membranes unstable in water. Here, we report a nanolaminate membrane based on covalently functionalized molybdenum disulfide (MoS2) nanosheets. The functionalized MoS2 membranes demonstrate >90% and ~87% rejection for micropollutants and NaCl, respectively, when operating under reverse osmotic conditions. The sieving performance and water flux of the functionalized MoS2 membranes are attributed both to control of the capillary widths of the nanolaminates and to control of the surface chemistry of the nanosheets. We identify small hydrophobic functional groups, such as the methyl group, as the most promising for water purification. Methyl- functionalized nanosheets show high water permeation rates as confirmed by our molecular dynamic simulations, while maintaining high NaCl rejection. Control of the surface chemistry and the interlayer spacing therefore offers opportunities to tune the selectivity of the membranes while enhancing their stability.

Efficient nanoparticles removal and bactericidal action of electrospun nanofibers membranes for air filtration.

Human exposure to air pollution and especially to nanoparticles is increasing due to the combustion of carbon-based energy vectors. Fibrous filters are among the various types of equipment potentially able to remove particles from the air. Nanofibers are highly effective in this area; however, their utilization is still a challenge due to the lack of studies taking into account both nanoparticle collection efficiency and antibacterial effect. The aim of this work is to produce and evaluate novel silver/polyacrylonitrile (Ag/PAN) electrospun fibers deposited on a nonwoven substrate to be used as air filters to remove nanoparticles from the air and also showing antibacterial activity. In order to determine the optimum manufacturing conditions, the effects of several electrospinning process parameters were analyzed such as solution concentration, collector to needle distance, flow rate, voltage, and duration. Ag/PAN nanofibers were characterized by X-ray diffraction (XRD), Transmission Electron Microscopy (TEM), Fourier Transform Infra-Red spectroscopy (FTIR), Energy-dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS), and Scanning Electron Microscopy (SEM). In addition, filtration performances were determined by measuring the pressure drop and collection efficiency of sodium chloride (NaCl) aerosol particles (9 to 300 nm diameters) using Scanning Mobility Particle Sizers (SMPS). Filters with high filtration efficiency (≈100%) and high-quality factor (≈0.05 Pa-1) were obtained even adding different concentrations of Ag nanoparticles (AgNPs) to PAN nanofibers. The resultant Ag/PAN nanofibers showed excellent antibacterial activity against 104 CFU/mL E. coli bacteria.

Role of Sulfur Vacancies and Undercoordinated Mo Regions in MoS2 Nanosheets toward the Evolution of Hydrogen.

Low-dimensional materials have been examined as electrocatalysts for the hydrogen evolution reaction (HER). Among them, two-dimensional transition metal dichalcogenides (2D-TMDs) such as MoS2 have been identified as potential candidates. However, the performance of TMDs toward HER in both acidic and basic media remains inferior to that of noble metals such as Pt and its alloys. This calls for investigating the influence of controlled defect engineering of 2D TMDs on their performance toward hydrogen production. Here, we explored the HER activity from defective multilayered MoS2 over a large range of surface S vacancy concentrations up to 90%. Amorphous MoS2 and 2H MoS2 with ultrarich S vacancies demonstrated the highest HER performance in acid and basic electrolytes, respectively. We also report that the HER performance from multilayered MoS2 can be divided into two domains corresponding to "point defects" at low concentrations of surface S vacancies (Stage 1) and large regions of undercoordinated Mo atoms for high concentrations of surface S vacancies (Stage 2). The highest performance is obtained for Stage 2 in the presence of undercoordinated Mo atoms with a TOF of ∼2 s-1 at an overpotential of 160 mV in 0.1 M KOH which compares favorably to the best results in the literature. Overall, our work provides deeper insight on the HER mechanism from defected MoS2 and provides guidance for the development of defect-engineered TMD-based electrocatalysts.

Fracture Mechanics and Oxygen Gas Barrier Properties of Al2O3/ZnO Nanolaminates on PET Deposited by Atomic Layer Deposition.

Rapid progress in the performance of organic devices has increased the demand for advances in the technology of thin-film permeation barriers and understanding the failure mechanisms of these material systems. Herein, we report the extensive study of mechanical and gas barrier properties of Al2O3/ZnO nanolaminate films prepared on organic substrates by atomic layer deposition (ALD). Nanolaminates of Al2O3/ZnO and single compound films of around 250 nm thickness were deposited on polyethylene terephthalate (PET) foils by ALD at 90 °C using trimethylaluminium (TMA) and diethylzinc (DEZ) as precursors and H2O as the co-reactant. STEM analysis of the nanolaminate structure revealed that steady-state film growth on PET is achieved after about 60 ALD cycles. Uniaxial tensile strain experiments revealed superior fracture and adhesive properties of single ZnO films versus the single Al2O3 film, as well as versus their nanolaminates. The superior mechanical performance of ZnO was linked to the absence of a roughly 500 to 900 nm thick sub-surface growth observed for single Al2O3 films as well as for the nanolaminates starting with an Al2O3 initial layer on PET. In contrast, the gas permeability of the nanolaminate coatings on PET was measured to be 9.4 × 10-3 O2 cm³ m-2 day-1. This is an order of magnitude less than their constituting single oxides, which opens prospects for their applications as gas barrier layers for organic electronics and food and drug packaging industries. Direct interdependency between the gas barrier and the mechanical properties was not established enabling independent tailoring of these properties for mechanically rigid and impermeable thin film coatings.

Adsorption and photocatalytic oxidation of ibuprofen using nanocomposites of TiO2 nanofibers combined with BN nanosheets: Degradation products and mechanisms.

This study investigated the adsorption and photocatalytic activity of titanium dioxide (TiO2)-boron nitride (BN) nanocomposites for the removal of contaminants of emerging concern in water using ibuprofen as a model compound. TiO2 nanofibers wrapped by BN nanosheets were synthesized by electrospinning method. Characterization of the nanocomposite photocatalysts indicated that the BN nanosheets improved the light absorbance and reduced the recombination of the photoexcited charge carriers (e- and h+). The photocatalytic oxidation products and mechanisms of ibuprofen by the TiO2-BN catalysts were elucidated using a multiple analysis approach by high performance liquid chromatography, ultraviolet absorbance, dissolved organic carbon, fluorescence excitation-emission matrices, and electrospray ionization-liquid chromatography-tandem mass spectrometry. The experimental results revealed that the photocatalytic oxidation by the TiO2-BN nanocomposites is a multi-step process and the interactions between ibuprofen molecules and the TiO2-BN nanocomposites govern the adsorption process. The increasing BN nanosheet content in the TiO2 nanofibers facilitated the breakdown of ibuprofen degradation intermediates (hydroxyibuprofen, carboxyibuprofen, and oxypropyl ibuprofen). Kinetic modeling indicated both adsorption and photocatalytic oxidation of ibuprofen by the TiO2-BN nanocomposites followed the first-order kinetic model. The photocatalytic oxidation rate increased with the increasing BN content in the nanocomposite catalysts, which was attributed to the enhanced light absorption capacity and the separation efficiency of the photoexcited electron (e-)-hole (h+) pairs. Multiple photocatalytic cycles were conducted to investigate the reusability and regeneration of the nanofibers for ibuprofen degradation.

Boron Nitride as a Novel Support for Highly Stable Palladium Nanocatalysts by Atomic Layer Deposition.

The ability to prepare controllable nanocatalysts is of great interest for many chemical industries. Atomic layer deposition (ALD) is a vapor phase technique enabling the synthesis of conformal thin films and nanoparticles (NPs) on high surface area supports and has become an attractive new route to tailor supported metallic NPs. Virtually all the studies reported, focused on Pd NPs deposited on carbon and oxide surfaces. It is, however, important to focus on emerging catalyst supports such as boron nitride materials, which apart from possessing high thermal and chemical stability, also hold great promises for nanocatalysis applications. Herein, the synthesis of Pd NPs on boron nitride (BN) film substrates is demonstrated entirely by ALD for the first time. X-ray photoelectron spectroscopy indicated that stoichiometric BN formed as the main phase, with a small amount of BNxOy, and that the Pd particles synthesized were metallic. Using extensive transmission electron microscopy analysis, we study the evolution of the highly dispersed NPs as a function of the number of ALD cycles, and the thermal stability of the ALD-prepared Pd/BN catalysts up to 750 °C. The growth and coalescence mechanisms observed are discussed and compared with Pd NPs grown on other surfaces. The results show that the nanostructures of the BN/Pd NPs were relatively stable up to 500 °C. Consequent merging has been observed when annealing the samples at 750 °C, as the NPs' average diameter increased from 8.3 ± 1.2 nm to 31 ± 4 nm. The results presented open up exciting new opportunities in the field of catalysis.

Exfoliation of Hexagonal Boron Nitride (h-BN) in Liquide Phase by Ion Intercalation.

A green approach to prepare exfoliated hexagonal boron nitride nanosheets (h-BNNS) from commercially pristine h-BN involving a two-step procedure was investigated. The first step involves the dispersion of pristine h-BN within an aqueous solution containing gelatin and potassium or zinc chloride using a sonication method. The second involves the removal of larger exfoliated h-BNNS through a centrifugation procedure. The exfoliation was caused not only by the sonication effect but also by intercalation of K⁺ and Zn2+ ions. Transmission electronic microscopy, X-ray diffraction and Raman spectroscopy techniques show that the obtained h-BNNS generally display a thickness of about a few (2⁻3) layers with an exfoliation efficiency as high as 16.3 ± 0.4%.

Atomic layer deposition for biosensing applications.

Atomic layer deposition (ALD) is a thin film deposition technique currently used in various nanofabrication processes for microelectronic applications. The ability to coat high aspect ratio structures with a wide range of materials, the excellent conformality, and the exquisite thickness control have made ALD an essential tool for the fabrication of many devices, including biosensors. This mini-review aims to provide a summary of the different ways ALD has been used to prepare biosensor devices. The materials that have been deposited by ALD, the use of the ALD layers prepared and the different types of biosensors fabricated are presented. A selected list of studies will be used to illustrate how the ALD route can be implemented to improve the operational performance of biosensors. This work comprehensively shows the benefits of ALD and its application in various facets of biosensing and will help in exploiting the numerous prospects of this emerging and growing field.