Fabrication of quantum dot-immobilized Y2O3 microspheres with effective photoluminescence for cancer radioembolization therapy.

Microspheres composed of Y-containing materials are effective agents for cancer radioembolization therapy using ß-rays. The distribution and dynamics of these microspheres in tissues can be easily determined by providing the microspheres with an imaging function. In addition, the use of quantum dots will enable the detection of microspheres at the individual particle level with high sensitivity. In this study, core - shell quantum dots were bound to chemically modified yttria microspheres under various conditions, and the effect of reaction conditions on the photoluminescence properties of the microspheres was investigated. The quantum dots were immobilized on the surfaces of the microspheres through dehydration - condensation reactions between the carboxy groups of quantum dots and the amino groups of silane-treated microspheres. As the reaction time increased, the photoluminescence peak blue shifted, and the photoluminescence intensity and lifetime decreased. Therefore, a moderate period of the immobilization process was optimal for imparting effective photoluminescence properties. This study is expected to facilitate particle-level tracking of microsphere dynamics in biological tissues for the development of minimally invasive cancer radiotherapy of deep-seated tumors.

We have established a method to immobilize quantum dots on yttria microspheres for cancer radiotherapy and revealed that photoluminescence intensity can be optimized by controlling the immobilization treatment time.

Preparation and characterizations of antibacterial poly(methyl methacrylate) bone cement via copolymerization with a quaternary ammonium monomer of dimethylaminotriclosan methacrylate.

Poly (methyl methacrylate) (PMMA) bone cement relies on the loaded antibiotic to realize the antibacterial purpose. But the exothermic behavior during setting often makes temperature-sensitive antibiotics inactivated. It is necessary to develop new material candidates to replace antibiotics. In this study, a new quaternary ammonium methacrylate (QAM) monomer called dimethylaminetriclosan methacrylate (DMATCM) was designed by the quaternization between 2-(Dimethylamino)ethyl methacrylate and triclosan, then employed as the modifier to explore the feasibility of equipping bone cement with antibacterial activity, and to investigate the variations on the physical and biological performances brought by the substitution ratio of DMATCM to MMA. Results showed that DMATCM opened its C=C bonding to participate in the MMA polymerization, and the quaternary ammonium group helped it to perform broad-spectrum antibacterial property against both Gram-positive Staphylococcus aureus and Gram-negative Escherichia coli. With an increased substitution ratio of DMATCM to MMA, the glass transition temperatures, the maximum exothermic temperatures, and the contact angles of bone cements declined, but the residual monomer contents, the fluid uptakes, and the setting times under Vical indentation increased. Long-term soaking made almost no changes to the weight loss and the mechanical properties of DMATCM-modified cements with lower substitution ratios of 0∼20%, and the activation rather enhanced the strengths of uncured AMBC-4 and AMBC-5 samples. Owing to more DMATCM exposed on the cement surface, the inhibition ring diameter produced by modified cement was improved to a maximum of 28.09 mm, and MC3T3-E1 cells performed the cell viabilities all beyond 70% and healthy adhesion after 72 h co-culturing. Taking all measured properties and ISO standards into account, the antibacterial bone cement under the ratio of 10% performed better, besides its good bactericidal effect, the other properties satisfied the requirements for clinical application.

Enhancement of apatite formation on Ti-50Zr alloy in simulated body environment.

Ti-50Zr alloy is 2.5 times as strong as pure Ti and has a lower Young's modulus, making it a useful material for repairing bone and teeth. However, Ti-50Zr alloy has a limited ability to bond with bone in vivo. Under biological conditions, apatite formation at the surface of a Ti or alloy implant is necessary for its bonding with bone. Various approaches to surface modification have been proposed to impart bone-bonding ability to Ti-50Zr alloy; however, there remains a need for further improvements to the alloy's apatite-forming ability. Hence, in this study, we compared apatite formation at the surface of alloy substrates in simulated body fluid, after various surface treatments. Treatment with 5 M NaOH followed by 1 M CaCl2 was the most effective procedure, whereas a sample subjected to a hot water post-treatment formed less apatite. Notably, no apatite formed on samples treated with 10 M NaOH.

In vitro and in vivo pharmacological profile of OPC-61815, a water-soluble phosphate ester pro-drug of tolvaptan.

Tolvaptan is an orally active vasopressin V2 receptor antagonist and used for the treatment of volume overload in some disease as an aquaretic. Tolvaptan sodium phosphate (OPC-61815) is a pro-drug of tolvaptan that was designed to improve water solubility and enable intravenous use. The conversion of OPC-61815 to tolvaptan was evaluated for in vitro and in vivo pharmacokinetic studies. The pharmacodynamics of OPC-61815 were evaluated for in vitro receptor binding affinity, in vivo aquaretic and anti-edematous action. The solubility of OPC-61815 in water at 25 °C was 72.4 mg/mL and more than 100,000 times the solubility of tolvaptan. OPC-61815 was hydrolyzed to tolvaptan by human tissue S9 fractions and main enzyme of hydrolysis was alkaline phosphatase. After intravenous administration of OPC-61815 to rats and dogs, tolvaptan was detected in plasma within 5 min and the bioavailability of tolvaptan was 57.7% and 50.9%, respectively. Binding affinity of OPC-61815 for the human V2 receptor was 1/14 weaker than that of tolvaptan. OPC-61815 exerted dose-dependent aquaretic action in rats and dogs and a corresponding anti-edematous action in rat edema models. These results suggest that OPC-61815, a water-soluble phosphate ester pro-drug of tolvaptan, is an effective aquaretic by converting to tolvaptan after intravenous administration.

Preparation of bioactive and antibacterial PMMA-based bone cement by modification with quaternary ammonium and alkoxysilane.

Bone cement based on poly(methyl methacrylate) (PMMA) powder and methyl methacrylate (MMA) liquid is a very popular biomaterial used for the fixation of artificial joints. However, there is a risk of this cement loosening from bone because of a lack of bone-bonding bioactivity. Apatite formation in the body environment is a prerequisite for cement bioactivity. Additionally, suppression of infection during implantation is required for bone cements to be successfully introduced into the human body. In this study, we modified PMMA cement with γ-methacryloxypropyltrimetoxysilane and calcium acetate to introduce bioactive properties and 2-(tert-butylamino)ethyl methacrylate (TBAEMA) to provide antibacterial properties. The long-term antibacterial activity is attributed to the copolymerization of TBAEMA and MMA. As the TBAEMA content increased, the setting time increased and the compressive strength decreased. After soaking in simulated body fluid, an apatite layer was detected within 7 days, irrespective of the TBAEMA content. The cement showed better antibacterial activity against Gram-negative E. Coli than Gram-positive bacteria; however, of the Gram-positive bacteria investigated, B. subtilis was more susceptible than S. aureus.

Fabrication and properties of alginate/calcium phosphate hybrid beads: A comparative study.

BACKGROUND: Microbeads for bone repair have been widely studied because they can be conveniently used in clinical applications. OBJECTIVE: This study concerns the preparation, physical properties and in vitro characterisation of different types of alginate/calcium phosphate (CaP) ceramic microbeads, which were designed for use as drug delivery systems and bone-regeneration matrices. METHODS: Hybrid microbeads were successfully prepared from sodium alginate and various CaP, namely 𝛼-tricalcium phosphate, 𝛽-tricalcium phosphate and hydroxyapatite using the liquid droplet method. RESULTS: Porosity, swelling properties and in vitro degradation of the microbeads in the aqueous environment were significantly changed by the added CaP. The compressive strength of the blocks fabricated from the beads was around 120 MPa irrespective of the type of CaP. The initial release rate of the model drug methylene blue was suppressed by the addition of CaP. CONCLUSION: The alginate-CaP composite beads hold promising potential as an encapsulation carrier of drugs and component of bone substitutes.

Effect of Calcium Acetate Content on Apatite-Forming Ability and Mechanical Property of PMMA Bone Cement Modified with Quaternary Ammonium.

Polymethyl methacrylate (PMMA)-based bone cement is a popular biomaterial used for fixation of artificial joints. A next-generation bone cement having bone-bonding ability, i.e., bioactivity and antibacterial property is desired. We previously revealed that PMMA cement added with 2-(tert-butylamino)ethyl methacrylate, γ-methacryloxypropyltrimethoxysilane and calcium acetate showed in vitro bioactivity and antibacterial activity. This cement contains calcium acetate at 20% of the powder component. Lower content of the calcium acetate is preferable, because the release of a lot of calcium salt may degrade mechanical properties in the body environment. In the present study, we investigate the effects of calcium acetate content on the setting property and mechanical strength of the cement and apatite formation in simulated body fluid (SBF). The setting time increased and the compressive strength decreased with an increase in calcium acetate content. Although the compressive strength decreased after immersion in SBF for 7 d, all the cements still satisfied the requirements of ISO5833. Apatite was formed in SBF within 7 d on the samples where the calcium acetate content was 5% or more. Therefore, it was found that PMMA cement having antibacterial properties and bioactivity can be obtained even if the amount of the calcium acetate is reduced to 5%.

Compositional dependence of the apatite formation ability of Ti-Zr alloys designed for hard tissue reconstruction.

Ti-Zr alloys are expected to be novel biomaterials with low stress shielding owing to their lower Young's moduli than pure Ti. The drawback of metallic biomaterials is that their bone-bonding abilities are relatively low. NaOH and heat treatments have been performed to provide Ti-50Zr with apatite-forming ability in the body environment, which is essential for bone bonding. However, the systematic compositional dependence of apatite formation has not been revealed. In the present study, NaOH treatment of Ti-Zr alloys with various compositions and bone-bonding abilities was assessed in vitro by apatite formation in simulated body fluid (SBF). The corrosion current density in NaOH aqueous solution and the amount of Na incorporated into the surface tended to decrease with increasing Zr content. The apatite-forming ability of the treated alloy significantly decreased when the Zr content was ≥60 atom%. This phenomenon is attributed to the (1) low OH content on the surface, (2) low Na incorporation into the treated alloy surface, which enhances apatite formation, and (3) low ability of P adsorption to the Ti-Zr alloy in SBF following Ca adsorption to trigger apatite nucleation. Although the adhesion of the titanate/zirconate layer formed on the surfaces to the substrates increased as Zr content increased, the adhesion between the apatite and the substrate was still low.

Setting behavior, apatite-forming ability, mechanical strength of polymethylmethacrylate bone cement through bioactivity modification of phosphate functional groups combined with Ca2+ ions.

Bioactivity modification helps polymethylmethacrylate (PMMA) bone cement to reinforce its interfacial adhesion to bone tissues through the chemical bonding of apatite. Since Si-OH groups combined with Ca2+ ions have succeeded in inducing apatite formation, more combinations of functional groups and active ions are being explored. In this study, Bis[2-(methacryloyloxy)ethyl] phosphate (B2meP) containing phosphate (=PO4H) groups and Ca(CH3COO)2 supplying Ca2+ ion were adopted to investigate the feasibility of equipping PMMA bone cement with apatite-forming ability in vitro, more effects under designed contents on setting behavior, injectability, contact angle, cytotoxicity and mechanical strength were also investigated. Results showed B2meP copolymerized with MMA and became one section of PMMA chains, surface = PO4H groups and released Ca2+ ions pushed spherical apatite individuals nucleating and agglomerating into layer horizontally, Increasing B2meP content lowered the contact angle and the peak temperature, enhanced the cell viability of MC3T3-E1, but prolonged apatite forming period. Injectability rate performed a similar trend to setting time. Lower adding content and deposited apatite layer contributed to reduce the strength loss in soaking. Taking biological performance and other properties into balance, cement added with B2meP of 10 wt% in MMA and Ca(CH3COO)2 of 20 wt% in PMMA performed better.

Structural control of magnetite nanoparticles for hyperthermia by modification with organic polymers: effect of molecular weight.

Hyperthermia treatment using appropriate magnetic materials in an alternating magnetic field to generate heat has been recently proposed as a low-invasive cancer treatment method. Magnetite (Fe3O4) nanoparticles are expected to be an appropriate type of magnetic thermal seed for this purpose, and the addition of organic substances during the synthesis process has been studied for controlling particle size and improving biological functions. However, the role of the properties of the organic polymer chosen as the modifier in the physical properties of the thermal seed has not yet been comprehensively revealed. Therefore, this study clarifies these points in terms of the molecular weight and the charge of the functional groups of the added polymers. Excepting polyethyleneimine, the Fe3O4 crystallite size decreased with increasing polymer molecular weight. Neutral polymers did not suppress the Fe3O4 formation regardless of the difference in molecular weight, while suppression of the Fe3O4 formation was observed for low molecular weight anionic polymers and high molecular weight cationic polymers. Samples with a small amount of Fe3O4 or with crystallite size less than 10 nm induced low heat generation under an alternating magnetic field.

Cytocompatible and Antibacterial Properties of Chitosan-Siloxane Hybrid Spheres.

Microporous spheres in a hybrid system consisting of chitosan and γ-glycidoxypropyltrimethoxysilane (GPTMS) have advantages in a range of applications, e.g., as vehicles for cell transplantation and soft tissue defect filling materials, because of their excellent cytocompatibility with various cells. In this study, microporous chitosan-GPTMS spheres were prepared by dropping chitosan-GPTMS precursor sols, with or without a cerium chloride, into liquid nitrogen using a syringe pump. The droplets were then freeze dried to give the pores of size 10 to 50 µm. The cell culture tests showed that L929 fibroblast-like cells migrated into the micropores larger than 50 µm in diameter, whereas MG63 osteoblast-like cells proliferated well and covered the granule surfaces. The spheres with cerium chloride showed antibacterial properties against both gram-negative and gram-positive bacteria.

In situ synthesis of magnetic iron oxide nanoparticles in chitosan hydrogels as a reaction field: Effect of cross-linking density.

Magnetic iron oxides such as magnetite and γ-hematite have attracted considerable attention as thermoseeds for hyperthermia treatment because of their ability to generate heat under an alternating magnetic field. Control of the particle size and their combination with biocompatible polymers are expected to be beneficial for optimization of the nanoparticles. These processes can be accomplished through the synthesis of magnetite in gels, as the network structure of the polymer gel can control the grain growth of the magnetite. However, the effect of the cross-linking density of the gels remains unclear. In this study, we synthesized magnetic iron oxides in situ in chitosan hydrogels with different cross-linking densities and examined the crystalline structure and heat generation under alternating magnetic field. The crystalline phase and amount of magnetite were observed to be dependent on the cross-linking density of the gel, and the heat generation of the nanoparticles was governed by their crystalline structure and particle size rather than solely the amount of formed iron oxide.

In vitro apatite mineralization and heat generation of magnetite-reduced graphene oxide nanocomposites for hyperthermia treatment.

Nanocomposites of magnetite (Fe3O4) and reduced graphene oxide (rGO) generate heat under an alternating magnetic field and therefore have potential applications as thermoseeds for cancer hyperthermia treatment. However, the properties of such nanocomposites as biomaterials have not been sufficiently well characterized. In this study, the osteoconductivity of Fe3O4-rGO nanocomposites of various compositions was evaluated in vitro in terms of their apatite-forming ability in simulated body fluid (SBF). Furthermore, the heat generation of the nanocomposites was measured under an alternating magnetic field. The apatite-forming ability in SBF improved as the Fe3O4 content in the nanocomposite was increased. As the Fe3O4 content was increased, the nanocomposite not only rapidly raised the surrounding temperature to approximately 100 °C, but the specific absorption rate also increased. We assumed that the ionic interaction between the Fe3O4 and rGO was enhanced and that Brown relaxation was suppressed as the proportion of rGO in the nanocomposite was increased. Consequently, a high content of Fe3O4 in the nanocomposite was effective for improving both the osteoconductivity and heat generation characteristics for hyperthermia applications.

Structural Effects of Sulfur-Containing Functional Groups on Apatite Formation on Ca2+-Modified Copolymers in a Simulated Body Environment.

Chemical modification with specific functional groups has been the conventional method to develop bone-bonding bioactive organic-inorganic hybrids. These materials are attractive as bone substitutes because they are flexible and have a Young's modulus similar to natural bone. Immobilization of sulfonic acid groups (-SO3H) onto the polymer chain is expected to produce such hybrids because these groups induce apatite formation in a simulated body fluid (SBF) and enhance the activity of osteoblast-like cells. Sulfinic acid groups (-SO2H), which are derivatives of -SO3H, can also induce apatite nucleation. However, the structural effects of such sulfur-containing functional groups on apatite formation have not been elucidated. In the present study, apatite formation on Ca2+-modified copolymers containing -SO2H or -SO3H was investigated in a simulated body environment. The copolymer containing Ca2+ and -SO3H promoted Ca2+ release into the SBF and formed apatite faster (1 day) than the copolymer containing Ca2+ and -SO2H (14 days). In contrast, when they were not modified with Ca2+, the copolymer containing only -SO2H deposited the apatite faster (7 days) than that containing only -SO3H (>7 days) in the solution with Ca2+ concentration 1.5 times that of SBF. The former adsorbed larger amounts of Ca2+ than the latter. The measured stability constant of the complex indicated that the interaction of -SO2-···Ca2+ was more stable than that of -SO3-···Ca2+. It was found that both the release and adsorption of Ca2+ governed by the stability played an important role in induction of the apatite formation and that the apatite-forming ability of sulfur-containing functional groups drastically changed by the coexistence of Ca2+.

Structural effects of phosphate groups on apatite formation in a copolymer modified with Ca2+ in a simulated body fluid.

Organic-inorganic composites are novel bone substitutes that can ameliorate the mismatch of Young's moduli between natural bone and implanted ceramics. Phosphate groups contribute to the formation of apatite in a simulated body fluid (SBF) and the adhesion of osteoblast-like cells. Therefore, modification of a polymer with these functional groups is expected to enhance the ability of the organic-inorganic composite to bond with bone. Two phosphate groups have been used, phosphonic acid (-C-PO3H2) and phosphoric acid (-O-PO3H2). However, the effects of structural differences between these phosphate groups have not been clarified. In this study, the apatite formation of copolymers modified with Ca2+ and either -C-PO3H2 or -O-PO3H2 was examined. The mechanism of apatite formation is discussed based on analytical and computational approaches. The copolymers containing -O-PO3H2, but not those containing -C-PO3H2, formed apatite in the SBF, although both released similar amounts of Ca2+ into the SBF. Adsorption of HPO4 2- from -O-PO3H2 in the SBF following Ca2+ adsorption was confirmed by zeta-potential measurement and X-ray photoelectron spectroscopy. The measurement of the complex formation constant revealed that the -O-PO3 2-Ca2+ complex was thermodynamically unstable enough to convert into CaHPO4, which was not the case with -C-PO3 2-Ca2+. The formation of CaHPO4-based clusters was found to be a key factor for apatite nucleation. In conclusion, this study revealed that modification with -O-PO3H2 was more effective for enhancing apatite formation compared with -C-PO3H2.

Development of hafnium metal and titanium-hafnium alloys having apatite-forming ability by chemical surface modification.

Hafnium (Hf) has attracted considerable attention as a component of biomedical titanium (Ti) alloys with low Young's moduli and/or shape-memory functionalities, because its cytotoxicity is as low as that of Ti. The drawback of metals is that their bone-bonding ability is generally low. It is known that apatite formation in the body is a prerequisite for bone-bonding. Although several chemical treatments have been proposed for preparing Ti for bone-bonding, there have been no similar investigations for Hf. In the present study, NaOH- and heat-treatments were applied to pure Hf and Ti-Hf alloys and their bone-bonding ability was assessed in vitro with the use of simulated body fluid (SBF). After NaOH- and heat-treatments, anatase formed on alloys with low Hf content (20-40% (atom%) Hf); mixtures of sodium titanate and hafnium titanate formed on alloys with similar Ti and Hf content (60% Hf); and hafnium oxide formed on alloys with high Hf content (80% Hf and pure Hf). Precipitates of apatite were observed on all the metals in SBF, except for the alloy with 60% Hf. We speculated that the hafnium titanate formed on this alloy had a low apatite-forming ability owing to its high negative surface charge, which inhibited P adsorption. The apatite-forming abilities of the Ti-Hf alloys strongly depended on their Hf content. The present results indicate that Hf-based materials have good potential for bone-bonding. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 2519-2523, 2018.

Effect of metallographic structure and machining process on the apatite-forming ability of sodium hydroxide- and heat-treated titanium.

Although titanium (Ti) is clinically used for hard tissue reconstruction, it has low bone-bonding ability, i.e. bioactivity. Materials able to deposit apatite on their surfaces within the body is considered to exhibit bioactivity. Effects of the metallographic structure and machining process of Ti on its apatite-forming ability remains unclear. In this study, Ti substrates subjected to various preheating and machining processes were then subjected to NaOH and heat treatments. The apatite-forming abilities of resulting Ti were examined in simulated body fluid (SBF). Preheating of the Ti decreased its reactivity with NaOH solution. When quenched or annealed Ti was subjected to NaOH and heat treatments, the induction period for apatite formation in SBF slightly increased. This was attributed to a decrease in sodium titanate and increase in rutile on the Ti surface after the treatments. Substrates subjected to wire-electrical-discharge machining did not form apatite. This was attributed to the inhibition of PO43- adsorption on their surfaces following Ca2+ adsorption, which is an essential process for apatite nucleation. Contamination of Ti surface by components of the brass wire used in the machining contributed to the inhibition. The bioactivity of surface-modified Ti was therefore significantly affected by its thermal treatment and machining process.

Preparation of chitosan-hydroxyapatite composite mono-fiber using coagulation method and their mechanical properties.

Autograft has been carried out for anterior cruciate ligament (ACL) reconstruction surgery. However, it has negative aspect because patients lose their healthy ligaments from other part. We focus on a chitosan-hydroxyapatite (HAp) composite fiber as a scaffold of ligament regeneration. Chitosan- HAp composite fiber was made by using coagulation method. Chitosan-NaH2PO4 solution was coagulated with coagulation bath including calcium ion to get the mono-fiber and then treated with sodium hydroxide solution to form HAp in fiber matrix. The mechanical property of the fiber was improved by the stretching of the wet one because of the orientation of chitosan molecule and the interaction between chitosan and HAp. Maximum stress was improved with increasing of sodium dihydrogen phosphate until 0.03M. The swelling ratio of the fiber was inhibited by composited with HAp. Additionally, bone-bonding ability was confirmed by SBF soaking tests.

Characterization and degradation study of chitosan-siloxane hybrid microspheres synthesized using a microfluidic approach.

Chitosan microspheres can address challenges associated with poor bioavailability or unsustained drug release when used as drug delivery systems thanks to their mucoadhesiveness, which allows the drug dosage to be retained in the gastrointestinal track for extended periods. Chitosan-3-glycidoxypropyltrimethoxysilane-ß-glycerophosphate (chitosan-GPTMS-ß-GP) hybrid microspheres were synthetized through sol-gel processing using a microfluidic approach. Microspheres with uniform spherical shapes and sizes of approximately 650µm were obtained. The microstructures of the microspheres consisted of four different siloxane structures. The degradation behaviors of the hybrid microspheres were examined under acidic pH conditions mimicking those found in the gastrointestinal track. Microspheres with different GPTMS molar ratios were incubated under several pH conditions for 2weeks. The microspheres incubated at pH7.4 extended the lowest weight loss (27%-32%), whereas those incubated at pH1.7 and pH5.4 showed greater weight losses of 43-59% and 69-77%, respectively. The inhibition of the degradation at low pH was dependent on the siloxane network in the chitosan matrix. Phosphate was mostly released in early stages, and the released amount of silicon was dependent on the composition. GPTMS was released with a chitosan chain via the hydrolysis of a chitosan molecule. The pelargonidin was incorporated in the microspheres and the slow releasing was observed at acidic condition. The resistance of these hybrid microspheres to low-pH conditions for longer than a full digestion cycle is promising for gastrointestinal drug delivery applications.

Enhanced biosafety of silica coated gadolinium based nanoparticles.

One of the most important and novel approaches of biomedical engineering is the development of new, effective and non-invasive medical diagnosis abilities, and treatments that have such requirements as advanced technologies for tumor imaging. Gadolinium (Gd) compounds can be used as MRI contrast agents, however the release of Gd3+ ions presents some adverse side effects such as renal failure, pancreatitis or local necrosis. The main aim of the work was the development and optimization of Gadolinium based nanoparticles coated with silica to be used as bioimaging agent. Gd based nanoparticles were prepared through a precipitation method and afterwards, these nanoparticles were covered with silica, using Stöber method with ammonia and functionalized with 3-Aminopropyltriethoxysilane (APTES). Results showed that nanoparticles were homogeneous regarding chemical composition, silica layer thickness, total size and morphology. Also, silica coating was successfully not degraded after 4 weeks at pH 5.5, 6.0 and 7.4, contrary to GdOHCO3 nanoparticles that degraded. Regarding the in vitro cell tests, very good cell proliferation and viability were observed. In conclusion, the results showed that Gd based nanoparticles coated with silica for imaging applications were successfully obtained under a well-controlled method. Furthermore, silica coating may enhance magnetic nanoparticles biosafety because it avoids GdOHCO3 degradation into harmful products (such as Gd3+ ions) at physiological conditions.