ABSTRACT
Background: Although xenografts have shown successful results in GBR procedures due to their osteoconductive properties, many authors have opted to add co-adjuvant drugs to favor osteogenesis and differentiate cells into an osteoblastic lineage. Metformin has been shown to have bone-protective properties, regulating osteoclast differentiation, as well as the ability to promote osteoblast mineralization and differentiation. The present study aimed to evaluate the effect of the local application of a 1% metformin solution on bone neoformation in the treatment of an experimental bone defect in a guided bone regeneration animal model with a particulated bovine hydroxyapatite xenograft with hyaluronate. Methods: With this purpose in mind, two critical defects with 8 mm diameter and 0.5 mm depth were created in eight male New Zealand rabbit calvarias. Titanium cylinders were fixed in each defect and filled with particulate hydroxyapatite of bovine origin and sodium hyaluronate, with sterile injectable saline added to the control group and sterile 1% metformin solution added to the test group. At 6 weeks, the animals were euthanized, and samples were obtained and prepared for histomorphometric analysis. Results: A higher percentage of new bone formation was observed in the metformin samples than in the control samples, both in the region closest to the animal's calvaria and in the most distal region analyzed. A higher average bone-biomaterial contact percentage was observed in the samples, with metformin in both the proximal and distal regions. There was no statistically significant difference in the mean value in either region in both parameters. Conclusion: The local application of a 1% metformin solution in an animal model of guided bone regeneration with particulate bovine hydroxyapatite and hyaluronate resulted in greater bone neoformation and xenograft osseointegration than in the control group.
ABSTRACT
METHODS: Three models of a single internal connection bone level-type implant inserted into a posterior mandible bone section were constructed using a 3D finite element software: one control model without marginal bone loss and two test models, both with a circumferential peri-implant bone defect, one with a 3 mm high defect and the other one 6 mm high. A 150 N static load was tested on the central fossa at 6° relative to the axial axis of the implant. RESULTS: The results showed differences in the magnitude of strain and stress transferred to the bone between models, being the higher strain found in the trabecular bone around the implant with greater marginal bone loss. Stress distribution differed between models, being concentrated at the cortical bone in the control model and at the trabecular bone in the test models. CONCLUSION: Marginal bone loss around dental implants under occlusal loading influences the magnitude and distribution of the stress transferred and the deformation of peri-implant bone, being higher as the bone loss increases.
Subject(s)
Alveolar Bone Loss/surgery , Dental Implants/adverse effects , Mandible/surgery , Biomechanical Phenomena , Bone and Bones/physiology , Bone and Bones/surgery , Computer Simulation , Dental Stress Analysis , Finite Element Analysis , Humans , Models, Biological , Prostheses and Implants/adverse effects , Software , Stress, MechanicalABSTRACT
BACKGROUND: Implantoplasty reduces both implant diameter and the thickness of its walls, subsequently reducing the ability of the implant to resist fracture in response to functional load. In combination with an increase in the crown-implant ratio due to bone loss, this could increase the lever effect, which in presence of high masticatory forces or parafunctional habits, could lead to complications such as fracture of the implant or loosening of the prosthetic screw. OBJECTIVES: To determine the elastic limits of internal connection, dental implants of different designs and diameters after an implantoplasty. MATERIALS AND METHODS: This in vitro study included 315 tapered internal connection titanium dental implants, the threads of which were removed with an industrial milling machine-for standardized implantoplasty (IMP1; n = 105)-or with the conventional approach-manually, using high-speed burs (IMP2; n = 105). The remaining 105 implants were used as controls. The final implant diameters were recorded. The quality of the newly polished surfaces was assessed by scanning electron microscopy. All implants were subjected to a mechanical pressure resistance test. A Tukey's test for multiple comparisons was used to detect differences in the elastic limit and final implant diameters between the implant groups. RESULTS: There were statistically significant differences in the elastic limit between the IMP1, IMP2, and control groups (p < 0.05). Furthermore, the implant diameter was significantly smaller in the IMP1 and IMP2 groups (p < 0.05). Scanning electron microscopy revealed smooth implant surfaces in the IMP1 and IMP2 groups, with some titanium particles visible in the IMP1 group. CONCLUSIONS: Implantoplasty significantly decreased the elastic limit of internal connection titanium dental implants, especially in those with a smaller diameter (3-3.5 mm).
Subject(s)
Dental Implants , Crowns , Materials Testing , Microscopy, Electron, Scanning , TitaniumABSTRACT
La estabilidad primaria es un requisito importante para la supervivencia y éxito de los implantes durante la osteointegración. En los últimos años, los implantes inmediatos postextracción han demostrado ser una opción de tratamiento exitosa y predecible para la reposición de dientes con mal pronóstico, pero surge la duda de si dichos implantes alcanzan valores de estabilidad primaria comparables a aquellos colocados en hueso maduro. Comparar la estabilidad primaria de implantes inmediatos colocados en alveolos postextracción con la de implantes colocados en hueso maduro. Se llevó a cabo un estudio clínico retrospectivo, con los datos recogidos sobre 175 implantes, colocados en 175 pacientes. Todos los implantes colocados pertenecían al modelo Essential Cone (Klockner Implant System) y se dividieron en dos grupos: implantes inmediatos (Grupo A, n=31) e implantes colocados en hueso maduro (Grupo B, n=144). La estabilidad primaria de todos los implantes se midió mediante torque de inserción y análisis de frecuencia de resonancia con Osstell ISQ. No se encontraron diferencias estadísticamente significativas respecto a la estabilidad medida a través del torque de inserción (26,29+10,07 Vs 25,76+9,72 N/cm) pero sí que se encontraron diferencias significativas en la medida de la estabilidad primaria mediante AFR, siendo inferiores los valores correspondientes a los implantes colocados en los alveolos post exodoncia (60,74 ± 6,17 en sentido VL y 62,19 ± 7.64 en sentido MD frente a 68,34 ± 6.26 en sentido VL y 69,29 ± 7.98 en sentido MD obtenidos en los implantes colocados en hueso maduro). El torque de inserción de los implantes inmediatos es similar al de los implantes colocados en hueso maduro, pero sus valores ISQ son significativamente inferiores, lo que demuestra un mayor grado de micromovimiento, y por consiguiente, un mayor riesgo de fracaso durante el período de osteointegración.
Primary stability is an important requirement for the survival and success of implants during osseointegration. In recent years, immediate post-extraction implants have proven to be a successful and predictable treatment option for the replacement of teeth with a poor prognosis, but the question arises as to whether these implants reach primary stability values comparable to those placed in mature bone. The objective of the study was to compare the primary stability of immediate implants placed in post-extraction alveoli with that of implants placed in mature bone. A retrospective clinical study was carried out, with data collected on 175 implants, placed in 175 patients. All implants placed belonged to the Essential Cone model (Klockner Implant System) and were divided into two groups: immediate implants (Group A, n = 31) and implants placed in mature bone (Group B, n = 144). The primary stability of all implants was measured by insertion torque and resonance frequency analysis with Osstell ISQ. No statistically significant differences were found regarding the stability measured through the insertion torque (26.29 + 10.07 Vs 25.76 + 9.72 N / cm) but significant differences were found in the measurement of primary stability by means of AFR, the values corresponding to implants placed in the post-exodontic alveoli being lower (60.74 ± 6.17 in the VL direction and 62.19 ± 7.64 in the MD direction versus 68.34 ± 6.26 in the VL direction and 69.29 ± 7.98 in the MD direction obtained in implants placed in mature bone). The insertion torque of immediate implants is similar to that of implants placed in mature bone, but their ISQ values are significantly lower, which demonstrates a higher degree of micromotion, and therefore, a greater risk of failure during the period of osseointegration.
Subject(s)
Dental Prosthesis Retention , Dental Implantation, Endosseous/methods , Tooth Extraction , Vibration , Case-Control Studies , Retrospective Studies , Osseointegration , Torque , Immediate Dental Implant Loading , Resonance Frequency AnalysisABSTRACT
BACKGROUND: This study aimed to evaluate the effect of the implant design and the presence of cortical bone in the primary stability, as well as analyze the differences between the stability measurements obtained by two different resonance frequency analysis (RFA) devices. MATERIAL AND METHODS: A total of 80 Klockner implants of two different models [40 Essential Cone implants (group A) and 40 Vega implants (group B)] were used. The implants were placed in two polyurethane blocks that simulated the mechanical properties of the maxillary bone. One block featured a layer of cortical bone that was absent from the other block. The primary stability of all implants was measured by insertion torque and RFA using two different devices: Penguin RFA and Osstell IDX. RESULTS: Primary stability was superior in the cortical bone in both torque and RFA. In the block containing cortical bone, group A implants obtained a greater insertion torque than did group B. The insertion torque was lesser in the bone lacking cortex. Regarding the ISQ of the implants, group A presented higher values in the block with cortical bone, but the values were lower in the block without cortical bone. There were no significant differences between the values obtained from the Osstell IDX and Penguin RFA. CONCLUSIONS: The presence of cortical bone positively influences the primary stability of dental implants. The design of the implant also has a statistically significant influence on implant primary stability, although the impact depends on whether there is coronal cerclage or not. There were no statistically significant differences in the implant stability measurements obtained by two different devices. Key words:Implant stability, resonance frequency analysis, torque, osstell, penguin, cortical.
ABSTRACT
BACKGROUND/PURPOSE: The use of osteotomes as a technique for densification and expansion of the residual ridge is one of the most widely used procedures to achieve adequate peri-implant bone quantity and density. The aim of this study was to evaluate the influence of time and the elastic deformation of peri-implant bone in the primary stability of implants placed using osteotomes. MATERIALS AND METHODS: In each of 10 fresh fragments of cow rib, two implants were placed using osteotomes. The insertion torque and initial implant stability quotient (ISQ) values were measured. In the control implants, the immediate removal torque was measured, while in the test implants, after 15â¯min of placement, ISQ values were measured again, and the removal torque was measured. RESULTS: There were significant differences between the ISQ values and between the insertion torque and removal torque at 15â¯min. The ISQ values (perpendicular/parallel) increased between the initial moment (64.4⯱â¯9/70.3⯱â¯5.9) and 15â¯min (66/71.4⯱â¯6.4). The removal torque at 15â¯min (12.4⯱â¯5.8) was lower than the insertion torque (15.9⯱â¯5.9). Compression of the trabeculae in contact with the implant placed using osteotomes was observed, as well as a greater number of trabecular fractures in the implants placed using conventional drilling. CONCLUSION: There is an increase in ISQ values of dental implants placed using osteotomes after 15â¯min of placement.
