Carbon Dots: A Bright Future as Anticounterfeiting Encoding Agents.

Counterfeit products and data vulnerability present significant challenges in contemporary society. Hence, various methods and technologies are explored for anticounterfeiting encoding, with luminescent tracers, particularly luminescent carbon dots (CDs), emerging as a notable solution. CDs offer promising contributions to product security, environmental sustainability, and the circular economy. This critical review aims to highlight the luminescence responsiveness of CDs to physical and chemical stimuli, achieved through nanoengineering their chemical structure. The discussion will delve into the various tunable luminescence mechanisms and decay times of CDs, investigating preferential excitations such as up-conversion, delayed fluorescence, fluorescence, room temperature phosphorescence, persistent luminescence, energy and charge transfer, as well as photo-chemical interactions. These insights are crucial for advancing anticounterfeiting solutions. Following this exploration, a systematic review will focus on the research of luminescent CDs' smart encoding applications, encompassing anticounterfeiting, product tracing, quality certification, and information encryption. Finally, the review will address key challenges in implementing CDs-based technology, providing specific insights into strategies aimed at maximizing their stability and efficacy in anticounterfeiting encoding applications.

Impact of atomic layer deposited TiO2 on the photocatalytic efficiency of TiO2/w-VA-CNT nanocomposite materials.

Titanium oxide (TiO2) has been widely investigated as a photocatalytic material, and the fact that its performance depends on its crystalline structure motivates further research on the relationship between preparation methods and material properties. In this work, TiO2 thin films were grown on non-functionalized wave-like patterned vertically aligned carbon nanotubes (w-VA-CNTs) via the atomic layer deposition (ALD) technique. Grazing incidence X-ray diffraction (GIXRD) analysis revealed that the structure of the TiO2/VA-CNT nanocomposites varied from amorphous to a crystalline phase with increasing deposition temperature, suggesting a "critical deposition temperature" for the anatase crystalline phase formation. On the other hand, scanning transmission electron microscopy (STEM) studies revealed that the non-functionalized carbon nanotubes were conformally and homogeneously coated with TiO2, forming a nanocomposite while preserving the morphology of the nanotubes. X-ray photoelectron spectroscopy (XPS) provided information about the surface chemistry and stoichiometry of TiO2. The photodegradation experiments under ultraviolet (UV) light on a model pollutant (Rhodamine B, RhB) revealed that the nanocomposite comprised of anatase crystalline TiO2 grown at 200 °C (11.2 nm thickness) presented the highest degradation efficiency viz 55% with an illumination time of 240 min. Furthermore, its recyclability was also demonstrated for multiple cycles, showing good recovery and potential for practical applications.

Tuning Green to Red Color in Erbium Niobate Micro- and Nanoparticles.

Tetragonal Er0.5Nb0.5O2 and monoclinic ErNbO4 micro- and nanoparticles were prepared by the citrate sol-gel method and heat-treated at temperatures between 700 and 1600 °C. ErNbO4 revealed a spherical-shaped crystallite, whose size increased with heat treatment temperatures. To assess their optical properties at room temperature (RT), a thorough spectroscopic study was conducted. RT photoluminescence (PL) spectroscopy revealed that Er3+ optical activation was achieved in all samples. The photoluminescence spectra show the green/yellow 2H11/2, 4S3/2→4I15/2 and red 4F9/2→4I15/2 intraionic transitions as the main visible recombination, with the number of the crystal field splitting Er3+ multiplets reflecting the ion site symmetry in the crystalline phases. PL excitation allows the identification of Er3+ high-energy excited multiplets as the preferential population paths of the emitting levels. Independently of the crystalline structure, the intensity ratio between the green/yellow and red intraionic transitions was found to be strongly sensitive to the excitation energy. After pumping the samples with a resonant excitation into the 4G11/2 excited multiplet, a green/yellow transition stronger than the red one was observed, whereas the reverse occurred for higher excitation photon energies. Thus, a controllable selective excited tunable green to red color was achieved, which endows new opportunities for photonic and optoelectronic applications.

THORACIC SYMPATHECTOMY: SEDATION EXPERIENCE.

Introduction/Study Goals: Thoracic sympathectomy is considered to be the most effective treatment for hyperhidrosis, a procedure traditionally performed under general anesthesia. Nowadays it's a minimally invasive procedure, which makes it possible to perform under sedation with local anesthesia. The goal in this study was to assess the efficacy and safety of this anesthetic technique in video-assisted thoracic sympathectomy. MATERIAL AND METHODS: The study took place in Centro Hospitalar Universitário Lisboa Norte, between June 2017 and September 2019. The anesthetic technique consisted in a propofol infusion titrated to achieve a moderate to deep sedation, in addition to local anesthesia with lidocaine 2% and ropivacaine 0,75% on surgical incisions. All patients were assessed subsequently for pain and anesthetic or surgical complications, with a 30-day follow-up. RESULTS: From a final sample of 63 patients, most were female (70%), with age ranging between 15 and 57 years old. There were no intra-operative complications. On the immediate postoperative period there were only two cases of poorly controlled pain. CONCLUSION: Results showed efficiency and safety with sedation associated with local anaesthesia as an anaesthetic technique for video-assisted thoracic sympathectomy. This anaesthetic approach avoids possible complications associated with general anaesthesia and one lung ventilation, with good analgesic efficacy. However, there is still the need for a bigger sample to confirm the obtained results and to strengthen sedation as an anesthetic approach in thoracic sympathectomy.

Switching from a traditional undergraduate programme in (clinical) pharmacology and therapeutics to a problem-based learning programme.

PURPOSE: The pharmacology and clinical pharmacology and therapeutics (CPT) education during the undergraduate medical curriculum of NOVA Medical School, Lisbon, Portugal, was changed from a traditional programme (i.e. discipline-based, lectures) to a problem-based learning (PBL) programme (i.e. integrated, case-based discussions) without an increase in teaching hours. The aim of this study was to investigate whether this change improved the prescribing competencies of final-year medical students. METHODS: Final-year students from both programmes (2015 and 2019) were invited to complete a validated prescribing assessment and questionnaire. The assessment comprised 24 multiple-choice questions in three subdomains (working mechanism, side-effects and interactions/contraindications), and five clinical case scenarios of common diseases. The questionnaire focused on self-reported prescribing confidence, preparedness for future prescribing task and education received. RESULTS: In total, 36 (22%) final-year medical students from the traditional programme and 54 (23%) from the PBL programme participated. Overall, students in the PBL programme had significantly higher knowledge scores than students in the traditional programme (76% (SD 9) vs 67% (SD 15); p = 0.002). Additionally, students in the PBL programme made significantly fewer inappropriate therapy choices (p = 0.023) and fewer erroneous prescriptions than did students in the traditional programme (p = 0.27). Students in the PBL programme felt more confident in prescribing, felt better prepared for prescribing as junior doctor and completed more drug prescriptions during their medical training. CONCLUSION: Changing from a traditional programme to an integrated PBL programme in pharmacology and CPT during the undergraduate medical curriculum may improve the prescribing competencies of final-year students.

Giant Pleural Tumor And Severe Hypoglycemia: Doege-Potter Syndrome In A Previously Healthy Female.

AIntroduction: Doege-Potter's syndrome is a rare paraneoplastic syndrome, consisting in hypoglycemia and solitary fibrous tumor of the pleura. These tumors represent < 5% of all pleural tumours and can only be cured by surgery. In this article, we report a case of a patient presenting with severe hypoglycemia, as the only symptom, and a mass occupying the entire left hemithorax. Case presentation: A54 year old female with severe hypoglycemia, a chest radiography with almost total opacification of the left hemithorax and a computed tomography scan with a mass in the left hemithorax. Surgery was performed and a mass with 30cm × 18cm × 11cm weighing 3195g was resected. The postoperative course was uneventful with immediate resolution of the hypoglycemia. The immunohistochemistry diagnosis was solitary fibrous tumor of the pleura. Conclusions: Solitary fibrous tumor of the pleura are very rare. Less than 5% are associated with hypoglycemia, taking the form of Doege-Potter Syndrome. Radiation therapy and chemotherapy have shown low response rate and complete surgical resection is the only procedure that offers cure. This case reports describes a rare giant solitary fibrous tumor of the pleura with severe hypoglycemia, successfully treated by surgery. Long-term follow-up of the patient after the surgery is necessary for detection of any possible recurrence.

Iridium(III)porphyrin arrays with tuneable photophysical properties.

The photophysical properties of iridium(III) porphyrins complexes with two different axial ligands (Cl(CO) and bipyridine (bpy)) in solution and in cellulose acetate polymer matrix were investigated. The axial ligands substitution was made aiming to evaluate the photophysical properties and the solubility in different solvents. Therefore, dissimilar from the free porphyrin, non-polar solvents (as toluene) favours the quantum yield of iridium(III)porphyrins and ligands with a more extended π-conjugated compound as bpy results in higher yields. Moreover, despite all the porphyrins reveals a negative solvatochromism, the substitution of Cl(CO) ligand by bpy ligand exhibits similar solubility either on non-polar or polar solvents. The observed photoluminescence (PL) at room temperature appears at NIR region in contrast to the previously reported iridium(III) porphyrins. Comparing with free porphyrin H2TTP, the red/NIR PL spectra of the iridium(III)porphyrins (either in solution and in the polymer matrix) reveals remarkable changes. Particularly, a more significative decrease of the red/NIR intensity ratio was detected for [Ir(ttp)(bpy)2] 2 where the maxima of the NIR emission can be adjusted under suitable excitation wavelength.

Optical properties of hydrothermally synthesised and thermally annealed ZnO/ZnO2 composites.

ZnO/ZnO2 composites grown by hydrothermal synthesis at low temperature (180 °C) and thermally annealed at 300 °C were fully analysed by morphological, structural and optical techniques. X-ray diffraction patterns (XRD) and Raman spectroscopy clearly evidence the presence of both crystalline phases in the ZnO/ZnO2 sample. The differential scanning calorimetry analysis and thermogravimetric profiles indicate an exothermic event with a peak temperature ca. 225 °C, which is accompanied by a 8.5% weight loss, being attributed to the crystallization of ZnO from ZnO2. Upon a thermal annealing treatment at 300 °C the ZnO2 phase was completely converted into ZnO, as measured by XRD and Raman spectroscopy. Photoluminescence investigations reveal that the emission is dominated by a broad band recombination in both samples, due to the overlapping of different emitting centres, and that the peak position of the PL emission is dependent on the excitation density. The ZnO/ZnO2 sample exhibits a widening of the bandgap when compared to the one only containing ZnO, likely related to the presence of the additional ZnO2 phase and suggesting a bandgap energy of ~3.42 eV for this compound. Surface analysis revealed that the sample exhibits a surface area of 90 m2 g-1, which decreases to 30 m2 g-1 after the thermal annealing and the full conversion into ZnO. This difference in the surface area showed particular relevance in the stability of the measured optical properties. Particularly, the intensity of the photoluminescence signal was seen to be higher in the ZnO/ZnO2 sample and strongly dependent on the measurement atmosphere, highlighting its potential to be employed in the fabrication of optical-based sensing systems for environmental applications, namely in gas sensors.

ZnAl2O4 decorated Al-doped ZnO tetrapodal 3D networks: microstructure, Raman and detailed temperature dependent photoluminescence analysis.

3D networks of Al-doped ZnO tetrapods decorated with ZnAl2O4 particles synthesised by the flame transport method were investigated in detail using optical techniques combined with morphological/structural characterisation. Low temperature photoluminescence (PL) measurements revealed spectra dominated by near band edge (NBE) recombination in the UV region, together with broad visible bands whose peak positions shift depending on the ZnO : Al mixing ratios. A close inspection of the NBE region evidences the effective doping of the ZnO structures with Al, as corroborated by the broadening and shift of its peak position towards the expected energy associated with the exciton bound to Al. Both temperature and excitation density-dependent PL results pointed to an overlap of multiple optical centres contributing to the broad visible band, with the peak position dependent on the Al content. While in the reference sample the wavelength of the green band remained unchanged with temperature, in the case of the composites, the deep level emission showed a blue shift with increasing temperature, likely due to distinct thermal quenching of the overlapping emitting centres. This assumption was further validated by the time-resolved PL data, which clearly exposed the presence of more than one optical centre in this spectral region. PL excitation analysis demonstrated that the luminescence features of the Al-doped ZnO/ZnAl2O4 composites revealed noticeable changes not only in deep level recombination, but also in the material's bandgap when compared with the ZnO reference sample. At room temperature, the ZnO reference sample exhibited free exciton resonance at ∼3.29 eV, whereas the peak position for the Al-doped ZnO/ZnAl2O4 samples occurred at ∼3.38 eV due to the Burstein-Moss shift, commonly observed in heavily doped semiconductors. Considering the energy shift observed and assuming a parabolic conduction band, a carrier concentration of ∼1.82 ×1019 cm-3 was estimated for the Al-doped ZnO/ZnAl2O4 samples.

Probing surface states in C60 decorated ZnO microwires: detailed photoluminescence and cathodoluminescence investigations.

ZnO microwires synthesised by the flame transport method and decorated with C60 clusters were studied in detail by photoluminescence (PL) and cathodoluminescence (CL) techniques. The optical investigations suggest that the enhanced near band edge recombination observed in the ZnO/C60 composites is attributed to the reduction of the ZnO band tail states in the presence of C60. Well-resolved free and bound excitons recombination, as well as 3.31 eV emission, are observed with increasing amount of C60 flooding when compared with the ZnO reference sample. Moreover, a shift of the broad visible emission to lower energies occurs with increasing C60 content. In fact, this band was found to be composed by two optical centres peaked in the green and orange/red spectral regions, presenting different lifetimes. The orange/red band exhibits faster lifetime decay, in addition to a more pronounced shift to lower energies, while the peak position of the green emission only shows a slight change. The overall redshift of the broad visible band is further enhanced by the change in the relative intensity of the mentioned optical centres, depending on the excitation intensity and on the C60 flooding. These results suggest the possibility of controlling/tuning the visible emission outcome by increasing the C60 amount on the ZnO surface due to the surface states present in the semiconductor. An adequate control of such phenomena may have quite beneficial implications when sensing applications are envisaged.

ZnO decorated laser-induced graphene produced by direct laser scribing.

A scalable laser scribing approach to produce zinc oxide (ZnO) decorated laser-induced graphene (LIG) in a unique laser-processing step was developed by irradiating a polyimide sheet covered with a Zn/ZnO precursor with a CO2 laser (10.6 µm) under ambient conditions. The laser scribing parameters revealed a strong impact on the surface morphology of the formed LIG, on ZnO microparticles' formation and distribution, as well as on the physical properties of the fashioned composites. The ZnO microparticles were seen to be randomly distributed along the LIG surface, with the amount and dimensions depending on the used laser processing conditions. Besides the synthesis conditions, the use of different precursors also resulted in distinct ZnO growth's yields and morphologies. Raman spectroscopy revealed the existence of both wurtzite-ZnO and sp2 carbon in the majority of the produced samples. Broad emission bands in the visible range and the typical ZnO near band edge (NBE) emission were detected by photoluminescence studies. The spectral shape of the luminescence signal was seen to be extremely sensitive to the employed processing parameters and precursors, highlighting their influence on the composites' optical defect distribution. The sample produced from the ZnO-based precursor evidenced the highest luminescence signal, with a dominant NBE recombination. Electrochemical measurements pointed to the existence of charge transfer processes between LIG and the ZnO particles.

Hierarchical Aerographite 3D flexible networks hybridized by InP micro/nanostructures for strain sensor applications.

In the present work, we report on development of three-dimensional flexible architectures consisting of an extremely porous three-dimensional Aerographite (AG) backbone decorated by InP micro/nanocrystallites grown by a single step hydride vapor phase epitaxy process. The systematic investigation of the hybrid materials by scanning electron microscopy demonstrates a rather uniform spatial distribution of InP crystallites without agglomeration on the surface of Aerographite microtubular structures. X-ray diffraction, transmission electron microscopy and Raman scattering analysis demonstrate that InP crystallites grown on bare Aerographite are of zincblende structure, while a preliminary functionalization of the Aerographite backbone with Au nanodots promotes the formation of crystalline In2O3 nanowires as well as gold-indium oxide core-shell nanostructures. The electromechanical properties of the hybrid AG-InP composite material are shown to be better than those of previously reported bare AG and AG-GaN networks. Robustness, elastic behavior and excellent translation of the mechanical deformation to variations in electrical conductivity highlight the prospects of AG-InP applications in tactile/strain sensors and other device structures related to flexible electronics.

Buckminsterfullerene hybridized zinc oxide tetrapods: defects and charge transfer induced optical and electrical response.

Buckminster fullerene (C60) based hybrid metal oxide materials are receiving considerable attention because of their excellent fundamental and applied aspects, like semiconducting, electron transfer, luminescent behaviors, etc. and this work briefly discusses the successful fabrication of C60 decorated ZnO tetrapod materials and their detailed structure-property relationships including device sensing applications. The electron microscopy investigations indicate that a quite dense surface coverage of ZnO tetrapods with C60 clusters is achieved. The spectroscopy studies confirmed the identification of the C60 vibrational modes and the C60 induced changes in the absorption and luminescence properties of the ZnO tetrapods. An increased C60 concentration on ZnO results in steeper ZnO bandgap absorption followed by well-defined free exciton and 3.31 eV line emissions. As expected, higher amounts of C60 increase the intensity of C60-related visible absorption bands. Pumping the samples with photons with an energy corresponding to these absorption band maxima leads to additional emission from ZnO showing an effective charge transfer phenomenon from C60 to the ZnO host. The density of states model obtained from DFT studies for pure and C60 coated ZnO surfaces confirms the experimental observations. The fabricated C60-ZnO hybrid tetrapod based micro- and nanodevices showed interesting ethanol gas sensing characteristics.

Effect of N2 and H2 plasma treatments on band edge emission of ZnO microrods.

ZnO microrods were grown by laser assisted flow deposition technique in order to study their luminescence behaviour in the near band edge spectral region. Transmission electron microscopy analysis put in evidence the high crystallinity degree and microrod's compositional homogeneity. Photoluminescence revealed a dominant 3.31 eV emission. The correlation between this emission and the presence of surface states was investigated by performing plasma treatments with hydrogen and nitrogen. The significant modifications in photoluminescence spectra after the plasma treatments suggest a connexion between the 3.31 eV luminescence and the surface related electronic levels.

Luminescence studies on green emitting InGaN/GaN MQWs implanted with nitrogen.

We studied the optical properties of metalorganic chemical vapour deposited (MOCVD) InGaN/GaN multiple quantum wells (MQW) subjected to nitrogen (N) implantation and post-growth annealing treatments. The optical characterization was carried out by means of temperature and excitation density-dependent steady state photoluminescence (PL) spectroscopy, supplemented by room temperature PL excitation (PLE) and PL lifetime (PLL) measurements. The as-grown and as-implanted samples were found to exhibit a single green emission band attributed to localized excitons in the QW, although the N implantation leads to a strong reduction of the PL intensity. The green band was found to be surprisingly stable on annealing up to 1400°C. A broad blue band dominates the low temperature PL after thermal annealing in both samples. This band is more intense for the implanted sample, suggesting that defects generated by N implantation, likely related to the diffusion/segregation of indium (In), have been optically activated by the thermal treatment.

Effect of Eu-implantation and annealing on the GaN quantum dots excitonic recombination.

Undoped self-assembled GaN quantum dots (QD) stacked in superlattices (SL) with AlN spacer layers were submitted to thermal annealing treatments. Changes in the balance between the quantum confinement, strain state of the stacked heterostructures and quantum confined Stark effect lead to the observation of GaN QD excitonic recombination above and below the bulk GaN bandgap. In Eu-implanted SL structures, the GaN QD recombination was found to be dependent on the implantation fluence. For samples implanted with high fluence, a broad emission band at 2.7 eV was tentatively assigned to the emission of large blurred GaN QD present in the damage region of the implanted SL. This emission band is absent in the SL structures implanted with lower fluence and hence lower defect level. In both cases, high energy emission bands at approx. 3.9 eV suggest the presence of smaller dots for which the photoluminescence intensity was seen to be constant with increasing temperatures. Despite the fact that different deexcitation processes occur in undoped and Eu-implanted SL structures, the excitation population mechanisms were seen to be sample-independent. Two main absorption bands with maxima at approx. 4.1 and 4.7 to 4.9 eV are responsible for the population of the optically active centres in the SL samples.

Carotid body function in aged rats: responses to hypoxia, ischemia, dopamine, and adenosine.

The carotid body (CB) is the main arterial chemoreceptor with a low threshold to hypoxia. CB activity is augmented by A(2)-adenosine receptors stimulation and attenuated by D(2)-dopamine receptors. The effect of aging on ventilatory responses mediated by the CB to hypoxia, ischemia, and to adenosine and dopamine administration is almost unknown. This study aims to investigate the ventilatory response to ischemia and to adenosine, dopamine, and their antagonists in old rats, as well as the effect of hypoxia on adenosine 3',5'-cyclic monophosphate (cAMP) accumulation in the aged CB. In vivo experiments were performed on young and aged rats anesthetized with pentobarbitone and breathing spontaneously. CB ischemia was induced by bilateral common carotid occlusions. cAMP content was measured in CB incubated with different oxygen concentrations. Hyperoxia caused a decrease in cAMP in the CB at all ages, but no differences were found between normoxia and hypoxia or between young and old animals. The endogenous dopaminergic inhibitory tonus is slightly reduced. However, both the ventilation decrease caused by exogenous dopamine and the increase mediated by A(2A)-adenosine receptors are not impaired in aged animals. The bradycardia induced by adenosine is attenuated in old rats. The CB's peripheral control of ventilation is preserved during aging. Concerns have also arisen regarding the clinical usage of adenosine to revert supraventricular tachycardia and the use of dopamine in critical care situations involving elderly people.