Toward Sensor Measurement Reliability in Blockchains.

In this work, a secure architecture to send data from an Internet of Things (IoT) device to a blockchain-based supply chain is presented. As is well known, blockchains can process critical information with high security, but the authenticity and accuracy of the stored and processed information depend primarily on the reliability of the information sources. When this information requires acquisition from uncontrolled environments, as is the normal situation in the real world, it may be, intentionally or unintentionally, erroneous. The entities that provide this external information, called Oracles, are critical to guarantee the quality and veracity of the information generated by them, thus affecting the subsequent blockchain-based applications. In the case of IoT devices, there are no effective single solutions in the literature for achieving a secure implementation of an Oracle that is capable of sending data generated by a sensor to a blockchain. In order to fill this gap, in this paper, we present a holistic solution that enables blockchains to verify a set of security requirements in order to accept information from an IoT Oracle. The proposed solution uses Hardware Security Modules (HSMs) to address the security requirements of integrity and device trustworthiness, as well as a novel Public Key Infrastructure (PKI) based on a blockchain for authenticity, traceability, and data freshness. The solution is then implemented on Ethereum and evaluated regarding the fulfillment of the security requirements and time response. The final design has some flexibility limitations that will be approached in future work.

Near-Field Communication Tag for Colorimetric Glutathione Determination with a Paper-Based Microfluidic Device.

Here, we propose a microfluidic paper-based analytical device (µPAD) implemented with a near-field communication (NFC) tag as a portable, simple and fast colorimetric method for glutathione (GSH) determination. The proposed method was based on the fact that Ag+ could oxidize 3,3',5,5'-tetramethylbenzidine (TMB) into oxidized blue TMB. Thus, the presence of GSH could cause the reduction of oxidized TMB, which resulted in a blue color fading. Based on this finding, we developed a method for the colorimetric determination of GSH using a smartphone. A µPAD implemented with the NFC tag allowed the harvesting of energy from a smartphone to activate the LED that allows the capture of a photograph of the µPAD by the smartphone. The integration between electronic interfaces into the hardware of digital image capture served as a means for quantitation. Importantly, this new method shows a low detection limit of 1.0 µM. Therefore, the most important features of this non-enzymatic method are high sensitivity and a simple, fast, portable and low-cost determination of GSH in just 20 min using a colorimetric signal.

Editorial: Functional Nanomaterials for Sensor Applications.

Functional nanomaterials have become one of the most fascinating fields in nanotechnology [...].

RESEKRA: Remote Enrollment Using SEaled Keys for Remote Attestation.

This paper presents and implements a novel remote attestation method to ensure the integrity of a device applicable to decentralized infrastructures, such as those found in common edge computing scenarios. Edge computing can be considered as a framework where multiple unsupervised devices communicate with each other with lack of hierarchy, requesting and offering services without a central server to orchestrate them. Because of these characteristics, there are many security threats, and detecting attacks is essential. Many remote attestation systems have been developed to alleviate this problem, but none of them can satisfy the requirements of edge computing: accepting dynamic enrollment and removal of devices to the system, respecting the interrupted activity of devices, and last but not least, providing a decentralized architecture for not trusting in just one Verifier. This security flaw has a negative impact on the development and implementation of edge computing-based technologies because of the impossibility of secure implementation. In this work, we propose a remote attestation system that, through using a Trusted Platform Module (TPM), enables the dynamic enrollment and an efficient and decentralized attestation. We demonstrate and evaluate our work in two use cases, attaining acceptance of intermittent activity by IoT devices, deletion of the dependency of centralized verifiers, and the probation of continuous integrity between unknown devices just by one signature verification.

Sensing Capacity in Dysprosium Metal-Organic Frameworks Based on 5-Aminoisophthalic Acid Ligand.

Two novel metal-organic frameworks (MOFs), based on dysprosium as the metal and the 5-aminoisophthalic acid (5aip) ligand, have been solvothermally synthesized, with the aim of studying and modulating their luminescence properties according to the variation of solvent in the structure. These materials display intense photo-luminescence properties in the solid state at room temperature. Interestingly, one fascinating sensory capacity of compound 2 regards obtaining a variation of the signal, depending on the solvent to which it is exposed. These results pave the way for a new generation of sensitive chemical sensors.

Reconfigurable Electronic Platforms: A Top-Down Approach to Learn about Design and Integration of Electronic Systems.

This case report presents a real example of a study which introduces the use of reconfigurable platforms in the teaching of electronics engineering to establish a bridge between theory and practice. This gap is one of the major concerns of the electronics engineering students. Different strategies, such as simulation tools or breadboard implementations, have been followed so far to make it easier for students to practice what they study in lectures. However, many students still claim to have problems when they face real practical implementations. The use of reconfigurable platforms as a teaching tool is proposed to provide the students the possibility of fast experimentation, reducing both development time and the learning curve. In addition, reconfigurable platforms available on the market make this methodology suitable to be applied throughout the different courses of their curricula. The feasibility of this approach is demonstrated in a course at the M.Eng. level, where the objective is the study, design and development of electronic sensor nodes. We firmly consider, based on the students' results and reflections collected during the course, that this methodology helps students to address the theoretical framework from a practical viewpoint, as well as to acquire some of the fundamental skills for their professional careers, such as the usage of communication protocols and embedded systems programming, in a more intuitive way when compared to traditional teaching methodologies.

Selectivity of Relative Humidity Using a CP Based on S-Block Metal Ions.

Herein, we present the syntheses of a novel coordination polymer (CP) based on the perylene-3,4,9,10-tetracarboxylate (pery) linkers and sodium metal ions. We have chosen sodium metal center with the aim of surmising the effect that the modification of the metal ion may have on the relative humidity (RH) experimental measurements of the material. We confirm the role of the ions in the functionalization of the deposited layer by modifying their selectivity towards moisture content, paving the way to the generation of sensitive and selective chemical sensors.

Camera-LiDAR Multi-Level Sensor Fusion for Target Detection at the Network Edge.

There have been significant advances regarding target detection in the autonomous vehicle context. To develop more robust systems that can overcome weather hazards as well as sensor problems, the sensor fusion approach is taking the lead in this context. Laser Imaging Detection and Ranging (LiDAR) and camera sensors are two of the most used sensors for this task since they can accurately provide important features such as target´s depth and shape. However, most of the current state-of-the-art target detection algorithms for autonomous cars do not take into consideration the hardware limitations of the vehicle such as the reduced computing power in comparison with Cloud servers as well as the reduced latency. In this work, we propose Edge Computing Tensor Processing Unit (TPU) devices as hardware support due to their computing capabilities for machine learning algorithms as well as their reduced power consumption. We developed an accurate and small target detection model for these devices. Our proposed Multi-Level Sensor Fusion model has been optimized for the network edge, specifically for the Google Coral TPU. As a result, high accuracy results are obtained while reducing the memory consumption as well as the latency of the system using the challenging KITTI dataset.

Optimization of Cost-Effective and Reproducible Flexible Humidity Sensors Based on Metal-Organic Frameworks.

In this letter, we present the extension of a previous work on a cost-effective method for fabricating highly sensitive humidity sensors on flexible substrates with a reversible response, allowing precise monitoring of the humidity threshold. In that work we demonstrated the use of three-dimensional metal-organic framework (MOF) film deposition based on the perylene-3,4,9,10-tetracarboxylate linker, potassium as metallic center and the interspacing of silver interdigitated electrodes (IDEs) as humidity sensors. In this work, we study one of the most important issues in efficient and reproducible mass production, which is to optimize the most important processes' parameters in their fabrication, such as controlling the thickness of the sensor's layers. We demonstrate this method not only allows for the creation of humidity sensors, but it also is possible to change the humidity value that changes the actuator state.

Carbon Dots as Sensing Layer for Printed Humidity and Temperature Sensors.

This work presents an innovative application of carbon dots (Cdots) nanoparticles as sensing layer for relative humidity detection. The developed sensor is based on interdigitated capacitive electrodes screen printed on a flexible transparent polyethylene terephthalate (PET) film. Cdots are deposited on top of these electrodes. An exhaustive characterization of the nanoparticles has been conducted along with the fabrication of the sensor structure. The accompanied experiments give all the sensibility to the Cdots, showing its dependence with temperature and exciting frequency. To the best of our knowledge, this work paves the path to the use of these kind of nanoparticles in printed flexible capacitive sensors aimed to be employed in the continuously expanding Internet of Things ecosystem.

treNch: Ultra-Low Power Wireless Communication Protocol for IoT and Energy Harvesting.

Although the number of Internet of Things devices increases every year, efforts to decrease hardware energy demands and to improve efficiencies of the energy-harvesting stages have reached an ultra-low power level. However, no current standard of wireless communication protocol (WCP) can fully address those scenarios. Our focus in this paper is to introduce treNch, a novel WCP implementing the cross-layer principle to use the power input for adapting its operation in a dynamic manner that goes from pure best-effort to nearly real time. Together with the energy-management algorithm, it operates with asynchronous transmissions, synchronous and optional receptions, short frame sizes and a light architecture that gives control to the nodes. These features make treNch an optimal option for wireless sensor networks with ultra-low power demands and severe energy fluctuations. We demonstrate through a comparison with different modes of Bluetooth Low Energy (BLE) a decrease of the power consumption in 1 to 2 orders of magnitude for different scenarios at equal quality of service. Moreover, we propose some security optimizations, such as shorter over-the-air counters, to reduce the packet overhead without decreasing the security level. Finally, we discuss other features aside of the energy needs, such as latency, reliability or topology, brought again against BLE.

Printed and Flexible Microheaters Based on Carbon Nanotubes.

This work demonstrates a cost-effective manufacturing method of flexible and fully printed microheaters, using carbon nanotubes (CNTs) as the heating element. Two different structures with different number of CNT layers have been characterized in detail. The benchmarking has been carried out in terms of maximum operating temperature, as well as nominal resistance and input power for different applied voltages. Their performances have been compared with previous reports for similar devices, fabricated with other technologies. The results have shown that the heaters presented can achieve high temperatures in a small area at lower voltages and lower input power. In particular, the fully printed heaters fabricated on a flexible substrate covering an area of 3.2 mm2 and operating at 9.5 V exhibit a maximum temperature point above 70 °C with a power consumption below 200 mW. Therefore, we have demonstrated that this technology paves the way for a cost-effective large-scale fabrication of flexible microheaters aimed to be integrated in flexible sensors.

Rational design of an unusual 2D-MOF based on Cu(i) and 4-hydroxypyrimidine-5-carbonitrile as linker with conductive capabilities: a theoretical approach based on high-pressure XRD.

Herein, we present, for the first time, a 2D-MOF based on copper and 4-hydroxypyrimidine-5-carbonitrile as the linker. Each MOF layer is perfectly flat and neutral, as is the case for graphene. High pressure X-ray diffraction measurements reveal that this layered structure can be modulated between 3.01 to 2.78 Å interlayer separation, with an evident piezochromism and varying conductive properties. An analysis of the band structure indicates that this material is conductive along different directions depending on the application of pressure or H doping. These results pave the way for the development of novel layered materials with tunable and efficient properties for pressure-based sensors.

Comparison of Laser-Synthetized Nanographene-Based Electrodes for Flexible Supercapacitors.

In this paper, we present a comparative study of a cost-effective method for the mass fabrication of electrodes to be used in thin-film flexible supercapacitors. This technique is based on the laser-synthesis of graphene-based nanomaterials, specifically, laser-induced graphene and reduced graphene oxide. The synthesis of these materials was performed using two different lasers: a CO2 laser with an infrared wavelength of λ = 10.6 µm and a UV laser (λ = 405 nm). After the optimization of the parameters of both lasers for this purpose, the performance of these materials as bare electrodes for flexible supercapacitors was studied in a comparative way. The experiments showed that the electrodes synthetized with the low-cost UV laser compete well in terms of specific capacitance with those obtained with the CO2 laser, while the best performance is provided by the rGO electrodes fabricated with the CO2 laser. It has also been demonstrated that the degree of reduction achieved with the UV laser for the rGO patterns was not enough to provide a good interaction electrode-electrolyte. Finally, we proved that the specific capacitance achieved with the presented supercapacitors can be improved by modifying the in-planar structure, without compromising their performance, which, together with their compatibility with doping-techniques and surface treatments processes, shows the potential of this technology for the fabrication of future high-performance and inexpensive flexible supercapacitors.

Portable Instrument for Hemoglobin Determination Using Room-Temperature Phosphorescent Carbon Dots.

A portable reconfigurable platform for hemoglobin determination based on inner filter quenching of room-temperature phosphorescent carbon dots (CDs) in the presence of H2O2 is described. The electronic setup consists of a light-emitting diode (LED) as the carbon dot optical exciter and a photodiode as a light-to-current converter integrated in the same instrument. The reconfigurable feature provides adaptability to use the platform as an analytical probe for CDs coming from different batches with some variations in luminescence characteristics. The variables of the reaction were optimized, such as pH, concentration of reagents, and response time; as well as the variables of the portable device, such as LED voltage, photodiode sensitivity, and adjustment of the measuring range by a reconfigurable electronic system. The portable device allowed the determination of hemoglobin with good sensitivity, with a detection limit of 6.2 nM and range up to 125 nM.

Fabrication and Characterization of Humidity Sensors Based on Graphene Oxide-PEDOT:PSS Composites on a Flexible Substrate.

In this paper, we present a simple, fast, and cost-effective method for the large-scale fabrication of high-sensitivity humidity sensors on flexible substrates. These sensors consist of a micro screen-printed capacitive structure upon which a sensitive layer is deposited. We studied two different structures and three different sensing materials by modifying the concentration of poly(3,4-ethylenedioxythiophene)/polystyrene sulfonate (PEDOT:PSS) in a graphene oxide (GO) solution. The results show that the aggregation of the PEDOT:PSS to the GO can modify its electrical properties, boosting the performance of the capacitive sensors in terms of both resistive losses and sensitivity to relative humidity (RH) changes. Thus, in an area less than 30 mm2, the GO/PEDOT:PSS-based sensors can achieve a sensitivity much higher (1.22 nF/%RH at 1 kHz) than other similar sensors presented in the literature which, together with their good thermal stability, time response, and performance over bending, demonstrates that the manufacturing approach described in this work paves the way for the mass production of flexible humidity sensors in an inexpensive way.

Inexpensive Graphene Oxide Heaters Lithographed by Laser.

In this paper, we present a simple and inexpensive method for the fabrication of high-performance graphene-based heaters on different large-scale substrates through the laser photothermal reduction of graphene oxide (laser-reduced graphene-oxide, LrGO). This method allows an efficient and localized high level of reduction and therefore a good electrical conductivity of the treated films. The performance of the heaters is studied in terms of steady-state temperature, power consumption, and time response for different substrates and sizes. The results show that the LrGO heaters can achieve stable steady-state temperatures higher than 200 °C when a voltage of 15 V is applied, featuring a time constant of around 4 s and a heat transfer coefficient of ~200 °C cm2/W. These characteristics are compared with other technologies in this field, demonstrating that the fabrication approach described in this work is competitive and promising to fabricate large-scale flexible heaters with a very fast response and high steady-state temperatures in a cost-effective way. This technology can be easily combined with other fabrication methods, such as screen printing or spray-deposition, for the manufacturing of complete sensing systems where the temperature control is required to adjust functionalities or to tune sensitivity or selectivity.

Laser-Fabricated Reduced Graphene Oxide Memristors.

Finding an inexpensive and scalable method for the mass production of memristors will be one of the key aspects for their implementation in end-user computing applications. Herein, we report pioneering research on the fabrication of laser-lithographed graphene oxide memristors. The devices have been surface-fabricated through a graphene oxide coating on a polyethylene terephthalate substrate followed by a localized laser-assisted photo-thermal partial reduction. When the laser fluence is appropriately tuned during the fabrication process, the devices present a characteristic pinched closed-loop in the current-voltage relation revealing the unique fingerprint of the memristive hysteresis. Combined structural and electrical experiments have been conducted to characterize the raw material and the devices that aim to establish a path for optimization. Electrical measurements have demonstrated a clear distinction between the resistive states, as well as stable memory performance, indicating the potential of laser-fabricated graphene oxide memristors in resistive switching applications.

Wearable System for Biosignal Acquisition and Monitoring Based on Reconfigurable Technologies.

Wearable monitoring devices are now a usual commodity in the market, especially for the monitoring of sports and physical activity. However, specialized wearable devices remain an open field for high-risk professionals, such as military personnel, fire and rescue, law enforcement, etc. In this work, a prototype wearable instrument, based on reconfigurable technologies and capable of monitoring electrocardiogram, oxygen saturation, and motion, is presented. This reconfigurable device allows a wide range of applications in conjunction with mobile devices. As a proof-of-concept, the reconfigurable instrument was been integrated into ad hoc glasses, in order to illustrate the non-invasive monitoring of the user. The performance of the presented prototype was validated against a commercial pulse oximeter, while several alternatives for QRS-complex detection were tested. For this type of scenario, clustering-based classification was found to be a very robust option.

A Potassium Metal-Organic Framework based on Perylene-3,4,9,10-tetracarboxylate as Sensing Layer for Humidity Actuators.

We have synthesized a novel three-dimensional metal-organic-framework (MOF) based on the perylene-3,4,9,10-tetracarboxylate linker and potassium as metallic centre. We report the formation of this K-based MOF using conventional routes with water as solvent. This material displays intense green photoluminescence at room temperature, and displays an aggregation dependent quenching. Correlation of the optical properties with the crystalline packing was confirmed by DFT calculations. We also demonstrate its potential to build humidity actuators with a reversible and reproducible response, with a change of 5 orders of magnitudes in its impedance at about 40% relative humidity (RH). This 3D-MOF is based on an interesting perylene derivative octadentate ligand, a moiety with interesting fluorescent properties and known component in organic semiconductors. To the best of our knowledge, this is the first time to build such a printed and flexible actuator towards humidity with a reversible response, enabling precise humidity threshold monitoring.