A Strategy to Valorize a By-Product of Pine Wood (Pinus pinaster) for Copper Removal from Aqueous Solutions.

This study describes the valorization of a pine wood by-product (Pinus pinaster) in the form of individualized fibers to a complex copper or more broadly metals present in an aqueous solution using a batch process. The adsorption results show that pine fibres activated by sodium carbonate are effective in recovering copper ions from monocontaminated or polycontaminated solutions of varying concentrations in a few minutes. One gram of material captures 2.5 mg of copper present in 100 mL of solution at pH 5 in less than 10 min. The results are perfectly reproducible and independent of pH between 3 and 5. The presence of the Na+ cation at concentrations of 0.1 M has no impact on material performance, unlike that of Ca2+ ions, which competes with Cu2+ ions for active sites. The adsorption process can be considered as rapid, as most of the copper is adsorbed within the first 10 min of exposure. Investigation of modeling possibilities shows some limitations. Indeed, the Weber and Morris and Elovich models show poor possibilities to describe all the kinetic data for copper adsorption on fibres. This may prove that the mechanism is far more complex than simple physisorption, chemisorption and/or diffusion. Complexation by wood fibers can be extended to solutions containing several types of metals. The results of this study show that the field of selective metal recovery could be a new way of valorizing by-products from the wood industry.

Field-Crop Soils in Eastern France: Coldspots of Azole-Resistant Aspergillus fumigatus.

Triazole fungicides are widely used to treat fungal pathogens in field crops, but very few studies have investigated whether fields of these crops constitute hotspots of azole resistance in Aspergillus fumigatus. Soil samples were collected from 22 fields in two regions of eastern France and screened for triazole residues and azole-resistant A. fumigatus (ARAf). Real-time quantitative PCR (qPCR) was used to quantify A. fumigatus in these soil samples. All the plots contained tebuconazole at concentrations from 5.5 to 19.1 ng/g of soil, and 5 of the 22 plots also contained epoxiconazole. Only a few fungal isolates were obtained, and no ARAf was detected. A. fumigatus qPCR showed that this fungal species was, on average, 5000 times more common in soil from flowerbeds containing ARAf than in soil from field crops. Thus, field-crop soils do not appear to promote A. fumigatus development, even if treated with azole fungicides, and cannot be considered hotspots of resistance. Indeed, our results suggest that they are instead a coldspot of resistance and highlight how little is known about the ecological niche of this species.

In situ and ex situ bioassays with Cantareus aspersus for environmental risk assessment of metal(loid) and PAH-contaminated soils.

Environmental risk assessment of contaminated soils requires bioindicators that allow the assessment of bioavailability and toxicity of chemicals. Although many bioassays can determine the ecotoxicity of soil samples in the laboratory, few are available and standardized for on-site application. Bioassays based on specific threshold values that assess the in situ and ex situ bioavailability and risk of metal(loid)s and polycyclic aromatic hydrocarbons (PAHs) in soils to the land snail Cantareus aspersus have never been simultaneously applied to the same soils. The aims of this study were to compare the results provided by in situ and ex situ bioassays and to determine their respective importance for environmental risk assessment. The feasibility and reproducibility of the in situ bioassay were assessed using an international ring test. This study used five plots located at a former industrial site and six laboratories participated in the ring test. The results revealed the impact of environmental parameters on the bioavailability of metal(loid)s and PAHs to snails exposed in the field to structured soils and vegetation compared to those exposed under laboratory conditions to soil collected from the same field site (excavated soils). The risk coefficients were generally higher ex situ than in situ, with some exceptions (mainly due to Cd and Mo), which might be explained by the in situ contribution of plants and humus layer as sources of exposure of snails to contaminants and by climatic parameters. The ring test showed good agreement among laboratories, which determined the same levels of risk in most of the plots. Comparison of the bioavailability to land snails and the subsequent risk estimated in situ or ex situ highlighted the complementarity between both approaches in the environmental risk assessment of contaminated soils, namely, to guide decisions on the fate and future use of the sites (e.g., excavation, embankments, and land restoration). Integr Environ Assess Manag 2022;18:539-554. © 2021 SETAC.

Sorption of 4-n-nonylphenol, 4-n-octylphenol, and 4-tert-octyphenol on cyclodextrin polymers.

Alkylphenols are industrial pollutants commonly present in wastewater. They are difficult to eliminate by conventional treatment processes, ending up in the sludge of wastewater treatment plants. In this study, we propose to use cross-linked cyclodextrin-based polymers (ECP) as sorbents to treat three alkylphenols, namely, one nonylphenol (4-n-NP) and two octylphenols (4-n-OP and 4-tert-OP), present in aqueous solution by a batch method. The experiments were carried out with five cyclodextrin polymers (α-ECP, ß-ECP, γ-ECP, α,ß,γ-ECP, and HP-ß-ECP). Sorption results showed that all polymers, with the exception of α-ECP, had high sorption capacities between 60 and 100% of the alkylphenols in the concentration range studied (between 25 and 100 µg/L). In all cases, HP-ß-ECP has shown the highest removals, regardless of the structure of the molecule. The order obtained was HP-ß-ECP >> ß-ECP ~ α,ß,γ-ECP >> γ-ECP > α-ECP. The 4-tert-OP compound was the best adsorbed, regardless the material and the solution studied. Sorption results also indicated that (i) the sorption efficiency decreased with the increasing of alkylphenol concentration; (ii) sodium chloride had a strong negative effect on the sorption process; and (iii) the performance remained unchanged after five sorption-regeneration cycles. The main sorption mechanism of alkylphenols occurring in ECP was the inclusion within the cyclodextrin cavities. The obtained results proved that cyclodextrin polymers could serve as efficient sorbents for the removal of alkylphenols from real effluents.

Use of Chènevotte, a Valuable Co-Product of Industrial Hemp Fiber, as Adsorbent for Pollutant Removal. Part I: Chemical, Microscopic, Spectroscopic and Thermogravimetric Characterization of Raw and Modified Samples.

FINEAU (2021-2024) is a trans-disciplinary research project involving French, Serbian, Italian, Portuguese and Romanian colleagues, a French agricultural cooperative and two surface-treatment industries, intending to propose chènevotte, a co-product of the hemp industry, as an adsorbent for the removal of pollutants from polycontaminated wastewater. The first objective of FINEAU was to prepare and characterize chènevotte-based materials. In this study, the impact of water washing and treatments (KOH, Na2CO3 and H3PO4) on the composition and structure of chènevotte (also called hemp shives) was evaluated using chemical analysis, X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectroscopy, X-ray computed nanotomography (nano-CT), attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy, solid state NMR spectroscopy and thermogravimetric analysis. The results showed that all these techniques are complementary and useful to characterize the structure and morphology of the samples. Before any chemical treatment, the presence of impurities with a compact unfibrillated structure on the surfaces of chènevotte samples was found. Data indicated an increase in the crystallinity index and significant changes in the chemical composition of each sample after treatment as well as in surface morphology and roughness. The most significant changes were observed in alkaline-treated samples, especially those treated with KOH.

Biosorbents from Plant Fibers of Hemp and Flax for Metal Removal: Comparison of Their Biosorption Properties.

Lignocellulosic fibers extracted from plants are considered an interesting raw material for environmentally friendly products with multiple applications. This work investigated the feasibility of using hemp- and flax-based materials in the form of felts as biosorbents for the removal of metals present in aqueous solutions. Biosorption of Al, Cd, Co, Cu, Mn, Ni and Zn from a single solution by the two lignocellulosic-based felts was examined using a batch mode. The parameters studied were initial metal concentration, adsorbent dosage, contact time, and pH. In controlled conditions, the results showed that: (i) the flax-based felt had higher biosorption capacities with respect to the metals studied than the hemp-based felt; (ii) the highest removal efficiency was always obtained for Cu ions, and the following order of Cu > Cd > Zn > Ni > Co > Al > Mn was found for both examined biosorbents; (iii) the process was rapid and 10 min were sufficient to attain the equilibrium; (iv) the efficiency improved with the increase of the adsorbent dosage; and (v) the biosorption capacities were independent of pH between 4 and 6. Based on the obtained results, it can be considered that plant-based felts are new, efficient materials for metal removal.

Hemp to limit diffusion of difenoconazole in vegetable garden soils.

Triazole molecules are used to manage invasive aspergillosis, a fungal infection mainly due to Aspergillus fumigatus. A. fumigatus is not a phytopathogen, but, as it is widespread in soils, triazole fungicides have an unintended impact on it, selecting resistant populations' in environment. Thus, to maintain our ability to control fungal infections, whether in human health or agriculture, reduce the impact of the use of triazoles in the environment is important, notably limiting their diffusion in soils. Here we tested a hemp-based material as adsorbent to limit the spread of difenoconazole, a triazole fungicide, in vegetable soils. We studied the effects of contact time, material dose, difenoconazole concentration, and organic content of the soil using batch mode and percolation methods. Batch experiments showed that the material exhibited high adsorption capacities toward difenoconazole. Removal from the soil water increased from 46.6% using 0.35 g hemp per kg of soil to 77.0% using 1.75 g hemp per kg, for a contact time of 15 min and an initial difenoconazole concentration of 1.2 mg/L. For a contact time of 240 min, the removal was 93.5%. Percolation experiments showed that the quantity of difenoconazole removed was greater than the amount obtained by batch method: 41.9% of removal with only one passes of solution at a concentration of 12 mg/L is obtained through percolation technique whereas, with similar conditions, only 20% of removal is obtained by batch method, i.e. after 1 min of contact. The removal was strongly dependent on the number of passes: the values increased from 57.0% to 91.0% with increasing the number of passes from 1 to 15. Addition of hemp to soils allows to remove efficiently the difenoconazole fungicide from soil water. Hemp-based felt is a new and safe adsorbent that can be applied in agriculture to limit crop contamination.

Determination of azole fungal residues in soils and detection of Aspergillus fumigatus-resistant strains in market gardens of Eastern France.

Medical azole antifungals are major compounds used to prevent and to treat invasive aspergillosis (IA). Azole fungicides, called DMI (14-alpha demethylase inhibitors), are also widely used for crop protection and have been reported to be linked to azole-resistant A. fumigatus (aR-Af) development in the environment. The aim of this study was to determine whether or not market gardens that spray DMIs in Eastern France are also affected by the presence of aR-Af. Forty aR-Afs were detected in soils in only two of the four market gardens using DMIs, with 23% (7/30) and 10% (3/30) of soils containing aR-Af. A total of 87.5% of these isolates had the TR34/L98H mutation and 22.5% the TR46/Y121F/T289A mutation on the cyp51A gene. Analyses of residual azole concentrations in soils showed the presence of difenoconazole for up to 2 years after spraying, but only in soils of market gardens where aR-Af was detected. It is very important to identify professional activities that could lead to aR-Af development and to develop preventive measures for at-risk patients living near professional activities using DMIs. We have to better understand why, in some cases, the use of DMI is not linked to aR-Af. Measures should be taken to avoid the use of DMI conferring cross-resistance to preserve the efficiency of human therapeutics.

Simultaneous removal of five triazole fungicides from synthetic solutions on activated carbons and cyclodextrin-based adsorbents.

In this study, an adsorption-oriented process for the removal of fungicides from polycontaminated aqueous solutions was applied. To remove triazole fungicides from aqueous mixtures of propiconazole (PROPI), tebuconazole (TEBU), epoxiconazole (EPOXI), bromuconazole (BROMU) and difenoconazole (DIFENO), several materials used as adsorbents were compared using batch experiments, namely two conventional activated carbons (ACs) and five nonconventional cross-linked cyclodextrin (CD)-based materials (α-CDP, ß-CDP, γ-CDP, αßγ-CDP mixture, and hydroxypropyl-ß-CDP). This article presents the abatements obtained. As expected, ACs exhibited the highest levels of triazole fungicide removal: the treatment lowered the five azoles by more than 99%, and adsorption was non-selective. Concerning CD-based materials employed for the first time for the removal of fungicides from polycontaminated aqueous solutions, results were interesting in particular for hydroxypropyl-ß-CDP: 1 g of adsorbent placed in 1 L of solution containing 1 mg of each of five triazoles (5 mg in total) was able to remove over half of the fungicide amount (2.97 mg). The order obtained was the following: BROMU << PROPI ≅ EPOXI < TEBU << DIFENO. This indicates that, in the mixture studied, strong competition prevailed among fungicides for the binding sites.

Desulfurization: Critical step towards enhanced selenium removal from industrial effluents.

Selenium (Se) removal from synthetic solutions and from real Flue Gas Desulfurization (FGD) wastewater generated by a coal-fired power plant was studied for the first time using a commercial iron oxide impregnated strong base anion exchange resin, Purolite® FerrIX A33E. In synthetic solutions, the resin showed high affinity for selenate and selenite, while sulfate exhibited a strong competition for both oxyanions. The FGD wastewater investigated is a complex system that contains Se (∼1200 µg L-1), SO42- (∼1.1 g L-1), Cl- (∼9.5 g L-1), and Ca2+ (∼5 g L-1), alongside a broad spectrum of toxic trace metals including Cd, Cr, Hg, Ni, and Zn. The resin performed poorly against Se in the raw FGD wastewater and showed moderate to good removal of several trace elements such as Cd, Cr, Hg, and Zn. In FGD effluent, sulfate was identified as a powerful competing anion for Se, having high affinity for the exchange active sites of the resin. The desulfurization of the FGD effluent using BaCl2 led to the increase in Se removal from 3% (non-desulfurized effluent) to 80% (desulfurized effluent) by combined precipitation and ion exchange treatment. However, complete desulfurization using equimolar BaCl2 could not be achieved due to the presence of bicarbonate that acts as a sulfate competitor for barium. In addition to selenium and sulfate removal, several toxic metals were efficiently removed (Cd: 91%; Cr: 100%; Zn: 99%) by the combined (desulfurization and ion exchange) treatment.

Cross-linked cyclodextrin-based material for treatment of metals and organic substances present in industrial discharge waters.

In this study, a polymer, prepared by crosslinking cyclodextrin (CD) by means of a polycarboxylic acid, was used for the removal of pollutants from spiked solutions and discharge waters from the surface treatment industry. In spiked solutions containing five metals, sixteen polycyclic aromatic hydrocarbons (PAH) and three alkylphenols (AP), the material exhibited high adsorption capacities: >99% of Co2+, Ni2+ and Zn2+ were removed, between 65 and 82% of the PAHs, as well as 69 to 90% of the APs. Due to the structure of the polymer and its specific characteristics, such as the presence of carboxylic groups and CD cavities, the adsorption mechanism involves four main interactions: ion exchange, electrostatic interactions and precipitation for metal removal, and inclusion complexes for organics removal. In industrial discharge waters, competition effects appeared, especially because of the presence of calcium at high concentrations, which competed with other pollutants for the adsorption sites of the adsorbent.

PAH occurrence in chalk river systems from the Jura region (France). Pertinence of suspended particulate matter and sediment as matrices for river quality monitoring.

This study investigates the variations of polycyclic aromatic hydrocarbon (PAH) levels in surface water, suspended particulate matter (SPM) and sediment upstream and downstream of the discharges of two wastewater treatment plant (WWTP) effluents. Relationships between the levels of PAHs in these different matrices were also investigated. The sum of 16 US EPA PAHs ranged from 73.5 to 728.0 ng L(-1) in surface water and from 85.4 to 313.1 ng L(-1) in effluent. In SPM and sediment, ∑16PAHs ranged from 749.6 to 2,463 µg kg(-1) and from 690.7 µg kg(-1) to 3,625.6 µg kg(-1), respectively. Investigations performed upstream and downstream of both studied WWTPs showed that WWTP discharges may contribute to the overall PAH contaminations in the Loue and the Doubs rivers. Comparison between gammarid populations upstream and downstream of WWTP discharge showed that biota was impacted by the WWTP effluents. When based only on surface water samples, the assessment of freshwater quality did not provide evidence for a marked PAH contamination in either of the rivers studied. However, using SPM and sediment samples, we found PAH contents exceeding sediment quality guidelines. We conclude that sediment and SPM are relevant matrices to assess overall PAH contamination in aquatic ecosystems. Furthermore, we found a positive linear correlation between PAH contents of SPM and sediment, showing that SPM represents an integrating matrix which is able to provide meaningful data about the overall contamination over a given time span.

Unexpected toxic interactions in the freshwater amphipod Gammarus pulex (L.) exposed to binary copper and nickel mixtures.

To document the toxicity of copper and nickel in binary mixtures, freshwater amphipods Gammarus pulex were exposed to the metals given independently or as mixtures. Toxicity to Cu alone was relatively high: 96-h LC10 and LC50 were found at 91 and 196 µg L(-1), respectively. Toxicity to Ni alone was very low, with 96-h LC10 and LC50 of 44,900 and 79,200 µg L(-1), respectively. Mixture toxicities were calculated from single toxicity data using conventional models. Modeled toxicity was then compared with the measured toxicity of the binary mixture. Two kinds of mixtures were tested. Type I mixtures were designed as combinations of Cu and Ni given at the same effect concentrations, when taken independently, to identify possible interactions between copper and nickel. In type II mixtures, Cu concentrations varied from 0 to 600 µg L(-1) while the nickel concentration was kept constant at 500 µg L(-1) to mimic conditions of industrial wastewater discharges. Ni and Cu showed synergic effects in type I mixtures while type II mixtures revealed antagonistic effects. Low doses of Ni reduced Cu toxicity towards G. pulex. These results show that even for simple binary mixtures of contaminants with known chemistry and toxicity, unexpected interactions between the contaminants may occur. This reduces the reliability of conventional additivity models.

Evaluation of the phytotoxicity of polycontaminated industrial effluents using the lettuce plant (Lactuca sativa) as a bioindicator.

Industrial wastewater containing heavy metals is generally decontaminated by physicochemical treatment consisting in insolublizing the contaminants and separating the two phases, water and sludge, by a physical process (filtration, settling or flotation). However, chemical precipitation does not usually remove the whole pollution load and the effluent discharged into the environment can be toxic even if it comes up to regulatory standards. To assess the impact of industrial effluent from 4 different surface treatment companies, we performed standardized bioassays using seeds of the lettuce Lactuca sativa. We measured the rate of germination, and the length and mass of the lettuce plantlet. The results were used to compare the overall toxicity of the different effluents: effluents containing copper and nickel had a much higher impact than those containing zinc or aluminum. In addition, germination tests conducted using synthetic solutions confirmed that mixtures of metals have higher toxicity than the sum of their separate constituents. These biological tests are cheap, easy to implement, reproducible and highlight the effects caused by effluent treated with the methods commonly applied in industry today. They could be routinely used to check the impact of industrial discharges, even when they meet regulatory requirements for the individual metals.

Cationized starch-based material as a new ion-exchanger adsorbent for the removal of C.I. Acid Blue 25 from aqueous solutions.

This article describes the use of a cationized starch-based material as new ion-exchanger adsorbent for the removal of C.I. Acid Blue 25 (AB 25) from aqueous solutions. Batch adsorption studies concerning the effects of contact time, pH and temperature are presented and discussed. Adsorption experimental data showed that: (i) the process was uniform and rapid: adsorption of dye reached equilibrium in 50 min in the wide pH range of dye solutions; (ii) adsorption kinetics followed the pseudo-second order model; (iii) the Langmuir model yielded a much better fit than the Freundlich model for the dye concentration range under study; (iv) this adsorbent exhibited interesting adsorption capacities: on the basis of the Langmuir analysis, the maximum adsorption capacity was determined to be 322 mg of dye per gram of material at 25 degrees C; (v) the adsorption capacity decreased with increasing temperature; and (vi) the negative value of free energy change indicated the spontaneous nature of adsorption.

Adsorption isotherm models for dye removal by cationized starch-based material in a single component system: error analysis.

This article describes the adsorption of an anionic dye, namely C.I. Acid Blue 25 (AB 25), from aqueous solutions onto a cationized starch-based adsorbent. Temperature was varied to investigate its effect on the adsorption capacity. Equilibrium adsorption isotherms were measured for the single component system and the experimental data were analyzed by using Langmuir, Freundlich, Tempkin, Generalized, Redlich-Peterson, and Toth isotherm equations. Five error functions were used to determine the alternative single component parameters by non-linear regression due to the bias in using the correlation coefficient resulting from linearization. The error analysis showed that, compared with other models, the Langmuir model described best the dye adsorption data. Both linear regression method and non-linear error functions provided the best-fit to experimental data with the Langmuir model.

The removal of Basic Blue 3 from aqueous solutions by chitosan-based adsorbent: batch studies.

Chitosan-based adsorbent (CHITOD material) is used for the removal of Basic Blue 3 (BB 3) from aqueous solutions. The adsorption of BB 3 on CHITOD material was studied as a function of time, sorbent mass and concentration. The influence of these parameters on the adsorption capacity was evaluated using the batch method. Results of adsorption experiments and kinetic data showed that (i) the CHITOD adsorbent exhibited high sorption capacities toward BB 3; (ii) the Langmuir equation represented the best fit of experimental data; (iii) the dye sorption on material was exothermic and spontaneous in nature; (iv) the kinetic measurements showed that the process was rapid; (v) the adsorption kinetics followed a pseudo-second order model; and (vi) the sorption was dependent on the presence of sulfonate groups. Non-linear method was also found to be more appropriate method for estimating the isotherm and kinetic parameters.