Valorisation of agri-food waste to fertilisers is a challenge in implementing the circular economy concept in practice.

The area of agricultural wastes valorisation to fertilizers is attracting growing attention because of the increasing fertilizer prices of fertilizers and the higher costs of waste utilization. Despite the scientific and political interest in the concept of circular economy, few studies have considered the practical approach towards the implementation of elaborated technologies. This article outlines innovative strategies for the valorisation of different biobased wastes into fertilizers. The present work makes a significant contribution to the field of new ideas for waste biomass management to recover significant fertilizer nutrients. These results emphasize the importance of the biomass use as a base of renewable resources, which has recently gained special importance, especially in relation to the outbreak of pandemia and war. Broken supply chains and limited access to deposits of raw materials used in fertilizer production (natural gas, potassium salts) meant that now, as never before, it has become more important and feasible to implement the idea of a circular economy and a green deal. We have obtained satisfactory results that demonstrate that appropriate management of biological waste (originating from agriculture, food processing, aquaculture, forest, pharmaceutical industry, and other branches of industry, sewage sludge) will not only reduce environmental nuisance (reducing waste heaps), but will also allow recovery of valuable materials, such as nitrogen (especially valuable amino acids), phosphorus, potassium, microelements, and biologically active substances with properties that stimulate plant growth. The results reported here provide information on production of biobased plant protection products (bioagrochemicals) from agri-food waste. This work reports an overview of biopesticides and biofertilisers production technologies and summarizes their properties and the mechanisms of action.

Biosorption as a method of biowaste valorization to feed additives: RSM optimization.

The aim of this work was to prepare an innovative microelemental feed additive for laying hens, based on waste biomass from the agricultural sector (alfalfa and goldenrod after CO2 extraction in supercritical state). The process was optimized by Response Surface Methodology (RSM) and the most favourable enrichment conditions were selected for Cu(II), Mn(II) and Zn(II) ions: pH - 5, sorbate concentration of Cu(II), Mn(II), Zn(II) - 10.0 mg/L for alfalfa and 10.7 mg/L for goldenrod and biomass dose - 0.1 g/L. Physicochemical properties of biomass were studied and functional groups involved in the binding of Cu(II), Mn(II), Zn(II) ions were determined (mainly carboxylic and hydroxylic groups). An interesting and unique element of this work is the verification of the properties of prepared feed additives in conditions simulating the digestive tract of animals. The release of components in solutions simulating conditions in the intestine and stomach (pH 11 and pH 1) was tested (in vitro tests). The best desorption results were achieved at a strongly acidic pH which corresponds to the stomach environment: 9.80, 14.4% Cu(II), 69.0, 66.9% (Zn), 46.5, 31.9 Mn(II) for alfalfa and goldenrod, respectively. It was concluded that the biomass enriched with micronutrients in biosorption has the potential as a feed additive for sustainable agriculture.

Efficient removal of mercury (II) from water by use of cryogels and comparison to commercial adsorbents under environmentally relevant conditions.

Mercury is a toxic element, which can be found in air, water and soil in several inorganic and organic forms. Mercury pollution comes from a variety of industrial sources, including vinyl-chloride, pulp and paper, fertilizers and pharmaceuticals industry, gold mining and cement production. Gels have increasingly attracted the interest over the past decades and one of the investigated applications is the fast removal of organic substances, metals and other cations and anions from water. In this work, two types of cryogels were synthesized at sub-zero temperature by free-radical polymerization technique, characterized by using a set of complimentary methods and used for the removal of mercury from aqueous solutions of different chemistry. Kinetics and equilibrium studies were performed in ultra-pure water solutions in order to study the mechanisms in the presence nitrate and chloride ions. The cryogels exhibited excellent efficiency towards mercury removal from all model solutions. Moreover, the cryogels were tested in different water matrixes (tap, river and sea water) and compared to commercial adsorbents (activated carbon, strong acid resin and zeolite Y). Cryogels were able to remove mercury much faster than commercial adsorbents with the exception of seawater where activated carbon was superior.

Analysis of tar compounds and quantification of naphthalene from thermal treatment of household biowaste.

Household biowaste represent the organic fraction of municipal solid waste and are an underutilized resource. Although previous studies have performed pyrolysis of organic waste, the vast majority has been on specific presorted feedstock or conventional lignocellulosic streams. Therefore, there is a lack of pyrolysis applications on representative food waste as retrieved from households and this can be attributed primarily to their high water content and their degradability. But via the intermediate step of drying, long-term storage and thermal treatment have become possible. In the framework of this study, household biowaste were pyrolyzed for the production of carbonaceous materials with a main focus on the analysis of produced tar compounds. Tars can be corrosive or cause clogging and disrupt the operation of pyrolysis and gasification plants. Their analysis has faced several difficulties due to inconsistency in the methodologies that have been applied by various groups. The tar protocol has provided a solid framework for consistent analysis of tars but until now has been solely used for the case of gasification. This study aimed to apply the tar protocol for pyrolysis and to enhance the detectability of the method for a wider range of tars by means of elemental analysis, attenuated total reflectance (ATR) and gas chromatography-mass spectrometry (GC-MS). GC- MS was performed by means of a specific column for PAHs identification and calibration methods were developed for the proper quantification of naphthalene which is the dominant tar compound. The results of the analysis showed that naphthalene concentration increased from torrefaction to carbonization but then decreased significantly for high temperature pyrolysis at 860 °C.

Thermodynamic modelling of an onsite methanation reactor for upgrading producer gas from commercial small scale biomass gasifiers.

Small scale biomass gasifiers have the advantage of having higher electrical efficiency in comparison to other conventional small scale energy systems. Nonetheless, a major drawback of small scale biomass gasifiers is the relatively poor quality of the producer gas. In addition, several EU Member States are seeking ways to store the excess energy that is produced from renewables like wind power and hydropower. A recent development is the storage of energy by electrolysis of water and the production of hydrogen in a process that is commonly known as "power-to-gas". The present manuscript proposes an onsite secondary reactor for upgrading producer gas by mixing it with hydrogen in order to initiate methanation reactions. A thermodynamic model has been developed for assessing the potential of the proposed methanation process. The model utilized input parameters from a representative small scale biomass gasifier and molar ratios of hydrogen from 1:0 to 1:4.1. The Villar-Cruise-Smith algorithm was used for minimizing the Gibbs free energy. The model returned the molar fractions of the permanent gases, the heating values and the Wobbe Index. For mixtures of hydrogen and producer gas on a 1:0.9 ratio the increase of the heating value is maximized with an increase of 78%. For ratios higher than 1:3, the Wobbe index increases significantly and surpasses the value of 30 MJ/Nm3.

Study and assessment of segregated biowaste composting: The case study of Attica municipalities.

This work aims to assess the operation of the first large scale segregated biowaste composting scheme in Greece to divert Household Food Waste (HFW) from landfill and produce a material which can be recovered and used as compost. The source separation and collection of HFW was deployed in selected areas in Attica Region serving about 3700 households. Sorted HFW is collected & transported to the Mechanical and Biological Treatment (MBT) plant in Attica Region that has been designed to produce Compost Like Output (CLO) from mixed MSW. The MBT facility has been adjusted in order to receive and treat aerobically HFW mixed with shredded green waste in a dedicated composting tunnel. The composting process was monitored against temperature, moisture and oxygen content indicating that the biological conditions are sufficiently developed. The product quality was examined and assessed against the quality specifications of EU End of Waste Criteria for biowaste subjected to composting aiming to specify whether the HFW that has undergone recovery ceases to be waste and can be classified as compost. More specifically, the heavy metals concentrations (Cr, Cu, Ni, Cd, Pb, Zn and Hg) are within the set limits and much lower compared to the CLO material that currently is being produced at the MBT plant. In regard to the hygienic requirements of the product it has been found that the process conditions result in a pathogen free material (i.e. E. Coli and Salmonella) which does not favor the growth of viable weeds and plant propagules, while it acquires sufficient organic matter content for soil fertilization. Noticeable physical impurities (mainly fractions of glass) have been detected exceeding the quality control threshold limit of 0.5% w/w (plastics, metals and glass). The latter is related to the missorted materials and to the limited pre-treatment configurations prior to composting. The above findings indicate that effective source separation of biowaste is prerequisite for good quality production and marketing of compost and special consideration should be made to minimize glass impurities prior composting (i.e. awareness raising and pretreatment stage). Therefore, it is feasible to gradually replace the production of questionable quality CLO in MBTs with biowaste compost which is in line with the required quality control standards especially when heavy metals concentrations is concerned.

Thermochemical valorization and characterization of household biowaste.

Valorization of municipal solid waste (MSW), by means of energy and material recovery, is considered to be a crucial step for sustainable waste management. A significant fraction of MSW is comprised from food waste, the treatment of which is still a challenge. Therefore, the conventional disposal of food waste in landfills is being gradually replaced by recycling aerobic treatment, anaerobic digestion and waste-to-energy. In principle, thermal processes like combustion and gasification are preferred for the recovery of energy due to the higher electrical efficiency and the significantly less time required for the process to be completed when compared to biological process, i.e. composting, anaerobic digestion and transesterification. Nonetheless, the high water content and the molecular structure of biowaste are constraining factors in regard to the application of thermal conversion pathways. Investigating alternative solutions for the pre-treatment and more energy efficient handling of this waste fraction may provide pathways for the optimization of the whole process. In this study, by means of utilizing drying/milling as an intermediate step, thermal treatment of household biowaste has become possible. Household biowaste has been thermally processed in a bench scale reactor by means of torrefaction, carbonization and high temperature pyrolysis. According to the operational conditions, fluctuating fractions of biochar, bio-oil (tar) and syngas were recovered. The thermochemical properties of the feedstock and products were analyzed by means of Simultaneous Thermal Analysis (STA), Ultimate and Proximate analysis and Attenuated Total Reflectance (ATR). The analysis of the products shows that torrefaction of dried household biowaste produces an energy dense fuel and high temperature pyrolysis produces a graphite-like material with relatively high yield.

Utilisation of biomass gasification by-products for onsite energy production.

Small scale biomass gasification is a sector with growth and increasing applications owing to the environmental goals of the European Union and the incentivised policies of most European countries. This study addresses two aspects, which are at the centre of attention concerning the operation and development of small scale gasifiers; reuse of waste and increase of energy efficiency. Several authors have denoted that the low electrical efficiency of these systems is the main barrier for further commercial development. In addition, gasification has several by-products that have no further use and are discarded as waste. In the framework of this manuscript, a secondary reactor is introduced and modelled. The main operating principle is the utilisation of char and flue gases for further energy production. These by-products are reformed into secondary producer gas by means of a secondary reactor. In addition, a set of heat exchangers capture the waste heat and optimise the process. This case study is modelled in a MATLAB-Cantera environment. The model is non-stoichiometric and applies the Gibbs minimisation principle. The simulations show that some of the thermal energy is depleted during the process owing to the preheating of flue gases. Nonetheless, the addition of a secondary reactor results in an increase of the electrical power production efficiency and the combined heat and power (CHP) efficiency.

Combination of decentralized waste drying and SSF techniques for household biowaste minimization and ethanol production.

The results of the demonstration of an innovative household biowaste management and treatment scheme established in two Greek Municipalities for the production of lignocellulosic ethanol using dehydrated household biowaste as a substrate, are presented within this research. This is the first time that biowaste drying was tested at a decentralized level for the production of ethanol using the Simultaneous Saccharification and Fermentation (SSF) process, at a pilot scale in Greece. The decentralized biowaste drying method proved that the household biowaste mass and volume reduction may reach 80% through the dehydration process used. The chemical characteristics related to lignocellulosic ethanol production have proved to differ substantially between seasons thus; special attention should be given to the process applied for ethanol production mainly regarding the enzyme quality and quantity used during the pretreatment stage. The maximum ethanol production achieved was 29.12g/L, approximately 60% of the maximum theoretical yield based on the substrate's sugar content. The use of the decentralized waste drying as an alternative approach for household biowaste minimization and the production of second generation ethanol is considered to be a promising approach for efficient biowaste management and treatment in the future.

ACL Reconstruction Decision Support. Personalized Simulation of the Lachman Test and Custom Activities.

INTRODUCTION: This article is part of the Focus Theme of Methods of Information in Medicine on "Methodologies, Models and Algorithms for Patients Rehabilitation". OBJECTIVES: The objective of the proposed approach is to develop a clinical decision support system (DSS) that will help clinicians optimally plan the ACL reconstruction procedure in a patient specific manner. METHODS: A full body model is developed in this study with 23 degrees of freedom and 93 muscles. The knee ligaments are modeled as non-linear spring-damper systems and a tibiofemoral contact model was utilized. The parameters of the ligaments were calibrated based on an optimization criterion. Forward dynamics were utilized during simulation for predicting the model's response to a given set of external forces, posture configuration and physiological parameters. RESULTS: The proposed model is quantified using MRI scans and measurements of the well-known Lachman test, on several patients with a torn ACL. The clinical potential of the proposed framework is demonstrated in the context of flexion-extension, gait and jump actions. The clinician is able to modify and fine tune several parameters such as the number of bundles, insertion position on the tibia or femur and the resting length that correspond to the choices of the surgical procedure and study their effect on the biomechanical behavior of the knee. CONCLUSION: Computational knee models can be used to predict the effect of surgical decisions and to give insight on how different parameters can affect the stability of the knee. Special focus has to be given in proper calibration and experimental validation.

Design of an innovative, ecological portable waste compressor for in-house recycling of paper, plastic and metal packaging waste.

Waste management in Greece relies heavily on unsustainable waste practices (mainly landfills and in certain cases uncontrolled dumping of untreated waste). Even though major improvements have been achieved in the recycling of municipal solid waste during recent years, there are some barriers that hinder the achievement of high recycling rates. Source separation of municipal solid waste has been recognised as a promising solution to produce high-quality recycled materials that can be easily directed to secondary materials markets. This article presents an innovative miniature waste separator/compressor that has been designed and developed for the source separation of municipal solid waste at a household level. The design of the system is in line with the Waste Framework Directive (2008/98/EC), since it allows for the separate collection (and compression) of municipal solid waste, namely: plastic (polyethylene terephthalate and high-density polyethylene), paper (cardboard and Tetrapak) and metal (aluminium and tin cans). It has been designed through the use of suitable software tools (LS-DYNA, INVENTROR and COMSOL). The results from the simulations, as well as the whole design process and philosophy, are discussed in this article.

Leaching properties of slag generated by a gasification/vitrification unit: the role of pH, particle size, contact time and cooling method used.

The environmental impact from the operation of thermal waste treatment facilities mainly originates from the air emissions, as well as the generated solid residues. The objective of this paper is to examine the slag residue generated by a demonstration plasma gasification/vitrification unit and investigate the composition, the leaching properties of the slag under different conditions, as well as the role of the cooling method used. The influence of pH, particle size and contact time on the leachability of heavy metals are discussed. The main outcome is that the vitrified slag is characterized as inert and stable and can be safely disposed at landfills or used in the construction sector. Finally, the water-cooled slag showed better resistance in relation to heavy metal leachability compared to the air-cooled slag.

Unobtrusive behavioral and activity-related multimodal biometrics: The ACTIBIO Authentication concept.

Unobtrusive Authentication Using ACTIvity-Related and Soft BIOmetrics (ACTIBIO) is an EU Specific Targeted Research Project (STREP) where new types of biometrics are combined with state-of-the-art unobtrusive technologies in order to enhance security in a wide spectrum of applications. The project aims to develop a modular, robust, multimodal biometrics security authentication and monitoring system, which uses a biodynamic physiological profile, unique for each individual, and advancements of the state of the art in unobtrusive behavioral and other biometrics, such as face, gait recognition, and seat-based anthropometrics. Several shortcomings of existing biometric recognition systems are addressed within this project, which have helped in improving existing sensors, in developing new algorithms, and in designing applications, towards creating new, unobtrusive, biometric authentication procedures in security-sensitive, Ambient Intelligence environments. This paper presents the concept of the ACTIBIO project and describes its unobtrusive authentication demonstrator in a real scenario by focusing on the vision-based biometric recognition modalities.

The impact of total mesorectal excision in middle and low rectal carcinomas.

PURPOSE: The incidence of locoregional recurrence in rectal cancer has declined since total mesorectal excision (TME) has been widely adopted. The purpose of this study was to investigate the long-term survival and the incidence of locoregional recurrences in patients with middle and low rectal carcinomas undergoing TME. METHODS: The medical records of 126 patients with middle and low rectal carcinomas treated from 1987-2007 were retrospectively reviewed. Of them 80 had undergone total mesorectal excision (TME-group) and 46 surgery with conventional methods (CON-group). Clinical variables were correlated to morbidity, hospital mortality, recurrence, sites of recurrence, and survival. RESULTS: The groups were comparable except for type of surgery and sites of recurrence. Five-year overall survival rate for TME group was 75% and for CON-group 47% (p=0.0346). Although the groups were not different for the total number of recurrences, the number of locoregional recurrences was significantly lower in TME group (p=0.004). CONCLUSION: TME appears to improve long-term survival in patients with middle and low rectal carcinomas. The incidence of locoregional recurrence is also reduced by TME.

Performance of a new household composter during in-home testing.

This article presents the methodology and the results of the performance testing of a prototype system for the production of high quality compost from biodegradable household waste separated at the source. Selected households in three municipalities of the Attica Region in Greece constituted the users of the home composter. The results indicated the effective operational performance of the prototype household composter in practice (use of the system by the householders on a daily basis), as well as the high level of response of the householders in adopting the composting practice in their daily activities as common practice. The compost that was produced in the households was characterized by high quality, which is in accordance with the quality standards that are set for its use. In only a few cases (in the first cycle of the pilot implementation) the quality of the compost was not high due to the fact that some householders were not yet familiar with the use of the composter, but these operational problems were solved and the compost that was later produced was considered high quality.

Preliminary study for the management of construction and demolition waste.

This paper refers to the management of the construction and demolition (C&D) waste since, according to the EU Waste Strategy, C&D waste is considered to be one of the priority waste streams and appropriate actions need to be taken with respect to its effective management. Initially, the paper presents the state-of-the-art of the problem of C&D waste, including the amount and composition of C&D waste in EU countries, differences in the characteristics of this waste stream depending on its origin, as well as collection and management practices that are applied. A methodology is described for the estimation of the quantities of the waste stream under examination, since in most cases quantitative primary data is not available. Next, the fundamentals for the development of an integrated scheme for the management of C&D waste are presented and discussed, such as appropriate demolition procedures and location of waste management (off-site waste management, on-site waste management, direct on-site recovery, centralized on-site recovery). Finally, taking into consideration all relevant parameters, alternative systems that could be applied for the management of the C&D waste are suggested.

Multi-criteria analysis for the determination of the best WEEE management scenario in Cyprus.

Waste from electrical and electronic equipment (WEEE) constitutes one of the most complicated solid waste streams in terms of its composition, and, as a result, it is difficult to be effectively managed. In view of the environmental problems derived from WEEE management, many countries have established national legislation to improve the reuse, recycling and other forms of recovery of this waste stream so as to apply suitable management schemes. In this work, alternative systems are examined for the WEEE management in Cyprus. These systems are evaluated by developing and applying the Multi-Criteria Decision Making (MCDM) method PROMETHEE. In particular, through this MCDM method, 12 alternative management systems were compared and ranked according to their performance and efficiency. The obtained results show that the management schemes/systems based on partial disassembly are the most suitable for implementation in Cyprus. More specifically, the optimum scenario/system that can be implemented in Cyprus is that of partial disassembly and forwarding of recyclable materials to the native existing market and disposal of the residues at landfill sites.

Analysis of results from the operation of a pilot plasma gasification/vitrification unit for optimizing its performance.

Plasma gasification/vitrification is an innovative and environmentally friendly method of waste treatment. A demonstration plasma gasification/vitrification unit was developed and installed in Viotia region in order to examine the efficiency of this innovative technology in dealing with hazardous waste. The preliminary results from the trial runs of the plasma unit, as well as the study of the influence of certain parameters in the system performance are presented and analyzed in this paper, contributing to the improvement of the operation performance. Finally, data on the final air emissions and the vitrified ash toxicity characteristic leaching procedure (TCLP) results are provided in order to assess the environmental performance of the system. The produced slag was found to be characterized by extremely low leaching properties and can be utilized as construction material, while the values of the polluting parameters of the air emissions were satisfactory.

Multi-criteria decision aid approach for the selection of the best compromise management scheme for ELVs: the case of Cyprus.

Each alternative scheme for treating a vehicle at its end of life has its own consequences from a social, environmental, economic and technical point of view. Furthermore, the criteria used to determine these consequences are often contradictory and not equally important. In the presence of multiple conflicting criteria, an optimal alternative scheme never exists. A multiple-criteria decision aid (MCDA) method to aid the Decision Maker (DM) in selecting the best compromise scheme for the management of End-of-Life Vehicles (ELVs) is presented in this paper. The constitution of a set of alternatives schemes, the selection of a list of relevant criteria to evaluate these alternative schemes and the choice of an appropriate management system are also analyzed in this framework. The proposed procedure relies on the PROMETHEE method which belongs to the well-known family of multiple criteria outranking methods. For this purpose, level, linear and Gaussian functions are used as preference functions.