Evaluation of polybenzimidazole-based polymers for the removal of uranium, thorium and palladium from aqueous medium.

Four types of polybenzimidazole (PBI)-based polymers (m-PBI, p-PBI, pyridine-based m-PBI and alkylated m-PBI) have been prepared and characterized. Extraction behaviour of heavy metal ions, viz. U(VI), Th(IV) and Pd(II), with these polymers was investigated. Distribution ratios for the extraction of these metal ions were measured as a function of nitric acid concentration. Extraction data reveal that, in general, p-PBI exhibits a higher distribution ratio for U(VI), Th(IV) and Pd(II) compared with the other polymeric resins evaluated in the present study. Column chromatography experiments were carried out with a solution of U(VI), Th(IV) and Pd(II) in dilute nitric acid media using columns packed with m- and p-PBI polymeric material for understanding the sorption and elution behaviour. The p-PBI-based resin has shown higher palladium sorption capacity (1.8 mmol g-1). The studies also established that p-PBI resin is a potential candidate material for the recovery of U(VI) and Th(IV) (capacity 0.22 mmol g-1 and 0.13 mmol g-1) from an aqueous stream, e.g. mine water samples.

Facile Synthesis of Mesoporous MnCO3 for Supercapacitor Applications.

We report a rapid and facile synthesis of MnCO3 with uniform mesopores for supercapacitor applications. Mesoporous MnCO3 was synthesised by a co-precipitation method using MnSO4 and (NH4)HCO3 as manganese and carbonate source, respectively. Powder X-ray diffraction study confirmed the formation of rhodochrosite phase of MnCO3. X-ray photoelectron spectroscopic study ascertained the oxidation state of Mn as 2+ in MnCO3. Scanning and Transmission electron microscopic studies revealed that nanograins of size less than 10 nm agglomerated into submicron sized spherical particles of MnCO3. N2 sorption studies displayed a typical type-IV isotherm with H2 hysteresis, demonstrating mesoporosity of as-prepared MnCO3. Furthermore, the mesoporous MnCO3 particles were evaluated for their capacitance properties by cyclic voltammetry and galvanostatic charge-discharge cycling in aqueous 0.1 M Mg(ClO4)2 electrolyte. The fabricated mesoporous MnCO3 electrodes delivered a specific capacitance of 144 F g-1 at a current density of 0.34 A g-1. It also exhibited good rate capability, high reversibility and cyclic stability over 1000 cycles.

Structural, Morphological and Antibacterial Investigation of Ag-Impregnated Sol-Gel-Derived 45S5 NanoBioglass Systems.

An increasing percentage of ageing population requires 30-year survivability of orthopedic devices that is not possible with the current bioinert materials, having a maximum of 15-year survivability. To satisfy this growing need, a shift is needed from replacement of tissues to regeneration of tissues. This is highly possible through the use of silica-bioactive glasses. However, a failure of implant can occur due to infections even by using such materials. Advances in using silver for antibacterial applications have been commercialized. However, higher concentrations of silver also lead to toxic effects. In this study, nanoBioglass 45S5 (NBG) and Ag-NBG were synthesized by using sol-gel method followed by solution-phase method, respectively. The bioactive crystals such as Na2Ca2Si3O9, CaCO3, and AgPO3, very much needed in the field of bone tissue engineering and in antibacterial strategies, were obtained in the NBG Matrix. The morphological investigation of NBG with 1 mM Ag+ concentrations shows the nanospikes arrangement of size 30-40 nm with spherical porous structure of size 10-20 nm, which supports the formation of collagen molecular fibrils on the surface of NBG matrices and enhances osseointegration. Both gram-positive and gram-negative strains show higher antibacterial activity for nanoBioglass with 1 mM Ag+ concentration.

In-vitro biocompatibility and corrosion resistance of strontium incorporated TiO2 nanotube arrays for orthopaedic applications.

This article investigates the in-vitro biocompatibility and corrosion behaviour of strontium ion incorporated TiO2 nanotube arrays formed by anodization method for orthopaedic applications. The morphological studies were carried out using field emission scanning electron microscopy, atomic force microscopy, attenuated total reflectance fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and thin film X-ray diffraction techniques. The morphological investigation indicated that the length and the average diameter of nanotube were 2.1 ± 0.3 µm and 110 ± 4 nm, respectively. The wettability measurements showed that the TiO2 nanotube arrays have super wettability, as well as, strontium ion incorporated TiO2 nanotube arrays exhibited hydrophilic behaviour. Excellent in-vitro bioactivity was observed for TiO2 nanotube arrays with strontium ions. Electrochemical studies in Hank's solution showed that the TiO2 nanotube arrays with strontium ions have enhanced corrosion resistance.

Studies to control biofilm formation by coupling ultrasonication of natural waters and anodization of titanium.

The main objective of this study was to investigate the combined effect of ultrasonication of natural waters and anodization of titanium on microbial density and biofilm formation tendency on titanium surfaces. Application of 24 kHz, 400 W high power ultrasound through a 14 mm horn type SS (stainless steel) Sonicator with medium amplitude of 60% for 30 min brought about three order decrease in total bacterial density of laboratory tap water, cooling tower water and reservoir water and two order decrease in seawater. Studies on the effect of ultrasonication on dilute pure cultures of Gram-negative and Gram-positive bacteria showed five order and three order decrease for Pseudomonas sp. and Flavobacterium sp. respectively and two order and less than one order decrease for Bacillus sp. and Micrococcus sp. respectively. Ultrasonication increased lag phase and reduced logarithmic population increase and specific growth rate of Gram-negative bacteria whereas for Gram-positive bacteria specific growth rate increased. Studies on the biofilm formation tendency of these ultrasonicated mediums on titanium surface showed one order reduction under all conditions. Detailed biofilm imaging by advanced microscopic techniques like AFM, SEM and epifluorescence microscopy clearly visualized the lysed/damaged cells and membrane perforations due to ultrasonication. Combination of ultrasonication and anodization brought about maximum decrease in bacterial density and biofilm formation with greater than two order decrease in seawater, two order decrease in Bacillus sp. culture and more than four order decrease in Flavobacterium sp. culture establishing the synergistic effect of anodization and ultrasonication in this study.

Synthesis of hydroxyapatite nanoparticles by a novel ultrasonic assisted with mixed hollow sphere template method.

Hydroxyapatite (HAP) is the main inorganic component of bone material and is widely used in various biomedical applications due to its excellent bioactivity and biocompatibility. In this paper, we have reported the synthesis of hydroxyapatite nanoparticles by a novel ultrasonic assisted mixed template directed method. In this method glycine-acrylic acid (GLY-AA) hollow spheres were used as an organic template which could be prepared by mixing of glycine with acrylic acid. The as-synthesized HAP nanoparticles were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscope (SEM) and tunnelling electron microscope (TEM) to investigate the nature of bonding, crystallinity, size and shape. The thermal stability of as-synthesized nanoparticles was also investigated by the thermo gravimetric analysis (TGA). The effect of ultrasonic irradiation time on the crystallinity and size of the HAP nanoparticles in presence of glycine-acrylic acid hollow spheres template were investigated. From the inspection of the above results it is confirmed that the crystallinity and size of the HAP nanoparticles decrease with increasing ultrasonic irradiation time. Hence the proposed synthesis strategy provides a facile pathway to obtain nano sized HAP with high quality, suitable size and morphology.

Studies on microbiologically influenced corrosion of SS304 by a novel manganese oxidizer, Bacillus flexus.

A manganese oxidizing bacterium was isolated from the surface of steel scraps and biochemical tests and 16S rRNA sequencing analysis confirmed the isolate as Bacillus flexus. Potentiodynamic polarization curves showed ennoblement of open circuit potential, increased passive current, a lowering of breakdown potential, active re-passivation potential and enhanced cathodic current in the presence of B. flexus. Adhesion studies with B. flexus on SS304 specimens with different surface treatments demonstrated decreased adhesion on passivated and FeCl(3) treated specimens due to the removal of MnS inclusions. The present study provides evidence that surface treatment of stainless steels can reduce adhesion of this manganese oxidizing bacterium and decrease the probability of microbiologically influenced corrosion.