Mid-troposphere transport of Middle-East dust over the Arabian Sea and its effect on rainwater composition and sensitive ecosystems over India.

The importance of mineral dust and aerosols in the transfer of bio-essential elements to terrestrial and marine ecosystems far removed from the source region is well known. Aerosol concentrations measured at the surface over the west coast of India during the SW monsoon period (June to September) are usually very low as pristine maritime air from the Southern Indian Ocean blows over this region. However, we find very high levels of mineral dust and dust derived nutrients in rainwater collected during the SW monsoon period. We show that the dry, warm and dusty Red Sea Wind and Shamal Wind from the Middle-East override the moist oceanic Low-Level Jet (Findlater Jet) of the SW monsoon and transport large quantities of dust at heights between 2 km and 5 km over the Indian Peninsula. A substantial portion is the desert dust is scavenged and wet-deposited over the Western Ghats of India where it neutralizes the acidity of rainwater and provides substantial amounts of nutrients that have the potential to impact sensitive ecosystems in this region. After the Red Sea and Shamal Winds subside in September, the alkaline rainwater reverts to the acidic range due to soluble ions derived from local carbonaceous aerosols.

Biomineralisation of manganese on titanium surfaces exposed to seawater.

A 2-year long study was carried out to isolate and characterise various bacterial species present in the biofilm formed on titanium surfaces exposed to seawater and to assess the manganese oxidizing potential of the marine isolates. The amount of manganese present in the biofilm was also measured using atomic absorption spectrometry (AAS). The results showed that titanium was susceptible to biofouling. More than 50% of the culturable marine bacterial isolates were capable of bringing about oxidation of Mn(II). All these manganese oxidizing bacteria were heterotrophic. Autotrophic manganese oxidizing bacteria such as Leptothrix was not isolated in the present study. The AAS results confirmed that the manganese content in the biofilms increased with increasing exposure time. Hence, the study indicates that the titanium surfaces when exposed to seawater were colonised by a large number of heterotrophic bacteria, which have the ability of bringing about biomineralisation of manganese.

Simulation of normal, carrier and affected controls for large-scale genotyping of cattle for factor XI deficiency.

An insertion mutation within exon 12 of the factor XI gene has been described in Holstein cattle. This has opened the prospect for large-scale screening of cattle using the polymerase chain reaction (PCR) technique for the rapid identification of heterozygous animals. To facilitate such a screening process, the mutant and normal alleles of factor XI gene, represented by 244- and 320-bp PCR amplified fragments, were individually cloned in Escherichia coli using a multicopy plasmid cloning vehicle to generate pFXI-N and pFXI-M, respectively. The authenticity of the inserts was confirmed by nucleotide sequencing. A nested PCR method was developed, by which PCR amplicons generated from primers with annealing sites on the recombinant plasmids and by flanking the insert were used as templates for amplification of the diagnostic products using factor XI gene-specific primers. An equimolar mixture of both PCR amplicons, originating from pFXI-N and pFXI-M, constituted the carrier control while the individual amplicons were the affected and normal controls. The controls were used as references for in-gel comparison to screen a population of 307 cattle and 259 water buffaloes; the frequency of the mutant allele was found to be 0. No DNA size standards were required in this study. The simulated control DNA samples representing normal, carrier and affected cattle have the potential to help in large-scale screening of a cattle population for individuals that are carriers or affected by factor XI deficiency.

Multiple myeloma presenting as stridor: A case report.

Extrame dullary plasmacytoma of larynx is extremely rare. We report a case of multiple myeloma which presented as extrame dullary manifestation in larynx. The rarity of incidence and difficulty in diagnosis of the disease is discussed.

Simulation of normal, carrier and affected controls for large-scale genotyping of cattle for factor XI deficiency

An insertion mutation within exon 12 of the factor XI gene has been described in Holstein cattle. This has opened the prospect for large-scale screening of cattle using the polymerase chain reaction (PCR) technique for the rapid identification of heterozygous animals. To facilitate such a screening process, the mutant and normal alleles of factor XI gene, represented by 244- and 320-bp PCR amplified fragments, were individually cloned in Escherichia coli using a multicopy plasmid cloning vehicle to generate pFXI-N and pFXI-M, respectively. The authenticity of the inserts was confirmed by nucleotide sequencing. A nested PCR method was developed, by which PCR amplicons generated from primers with annealing sites on the recombinant plasmids and by flanking the insert were used as templates for amplification of the diagnostic products using factor XI gene-specific primers. An equimolar mixture of both PCR amplicons, originating from pFXI-N and pFXI-M, constituted the carrier control while the individual amplicons were the affected and normal controls. The controls were used as references for in-gel comparison to screen a population of 307 cattle and 259 water buffaloes; the frequency of the mutant allele was found to be 0. No DNA size standards were required in this study. The simulated control DNA samples representing normal, carrier and affected cattle have the potential to help in large-scale screening of a cattle population for individuals that are carriers or affected by factor XI deficiency.

Photocatalytic inhibition of microbial adhesion by anodized titanium.

Biofouling is one of the concerns in the use of titanium for seawater cooled condensers of power plants. Earlier studies have shown that anodized titanium and its alloys with a thin film of anatase (TiO(2)) on its surface can inhibit attachment of Pseudomonas sp. when illuminated with near-UV light (350 - 380 nm). In the present study, a comparison of the photocatalytic inhibition of microbial attachment on titanium surfaces anodized at different voltages was carried out. Thin films of anatase of varying thickness were produced on titanium grade-2 by anodizing in dilute orthophosphoric acid solution at 30 V, 50 V and 100 V. The photocatalytic efficiency of these anodized surfaces was measured by the methylene blue degradation method. The anodised surfaces were exposed to liquid cultures of Gram-negative Pseudomonas sp., Gram-positive Micrococcus sp. and to a mixed algal culture. Photocatalytic inhibition of microbial attachment was maximum on the titanium surface anodized at 30 V, followed by the surface anodized at 50 V and then at 100 V. The photocatalytic inhibition of microbial attachment was also found to be dependent on the cell wall characteristics of the organism. The Gram-negative Pseudomonas sp. with a lipoproteinaceous outer membrane was the most susceptible to the photocatalytic effect, while the Gram-positive Micrococcus sp. with peptidoglycan cell wall showed moderate susceptibility and the algae with siliceous cell wall showed no susceptibility at all.

Influence of surface characteristics and microstructure on adhesion of bacterial cells onto a type 304 stainless steel.

A study was carried out to understand the influence of the surface characteristics/microstructure of a type 304 stainless steel on bacterial adhesion by exposing solution-annealed, sensitized and air-oxidized stainless steel specimens in a culture of Pseudomonas sp. in dilute nutrient broth. Epifluorescence microscopy of the exposed surfaces revealed that the pattern of adhesion as well as number density of bacterial cells was different depending on the metallurgical condition of the substratum. Among the specimens with different microstructures, the sensitized specimens had the highest bacterial density, followed by the solution annealed and the oxidized specimens. The same trend was shown by the total viable counts on the various surfaces, estimated by a plate count technique. The study assumes significance in the context of the widely reported observation of preferential attack of the welded region during microbiologically influenced corrosion of fabricated components.