Label-Free, Flow-Imaging Methods for Determination of Cell Concentration and Viability.

PURPOSE: To investigate the potential of two flow imaging microscopy (FIM) techniques (Micro-Flow Imaging (MFI) and FlowCAM) to determine total cell concentration and cell viability. METHODS: B-lineage acute lymphoblastic leukemia (B-ALL) cells of 2 different donors were exposed to ambient conditions. Samples were taken at different days and measured with MFI, FlowCAM, hemocytometry and automated cell counting. Dead and live cells from a fresh B-ALL cell suspension were fractionated by flow cytometry in order to derive software filters based on morphological parameters of separate cell populations with MFI and FlowCAM. The filter sets were used to assess cell viability in the measured samples. RESULTS: All techniques gave fairly similar cell concentration values over the whole incubation period. MFI showed to be superior with respect to precision, whereas FlowCAM provided particle images with a higher resolution. Moreover, both FIM methods were able to provide similar results for cell viability as the conventional methods (hemocytometry and automated cell counting). CONCLUSION: FIM-based methods may be advantageous over conventional cell methods for determining total cell concentration and cell viability, as FIM measures much larger sample volumes, does not require labeling, is less laborious and provides images of individual cells.

The Impact of Inadequate Temperature Storage Conditions on Aggregate and Particle Formation in Drugs Containing Tumor Necrosis Factor-Alpha Inhibitors.

PURPOSE: To measure aggregate and particle formation in tumor necrosis factor-alpha (TNF-α) inhibitors etanercept, adalimumab and certolizumab pegol product samples after exposure to freezing temperature conditions similar to storage conditions previously observed in patients' homes. METHODS: TNF-α inhibitors in their original primary and secondary packaging were exposed to 32 freeze-thaw cycles (-10°C for 120min/5°C for 60 min) or continuous low storage temperature (-20°C for 96 h) before thawing at 2-8°C. Non-stressed products were used as controls. The products were analyzed by high pressure size exclusion chromatography (HP-SEC), dynamic light scattering (DLS), nanoparticle tracking analysis (NTA), micro-flow imaging (MFI) and second derivative ultraviolet (UV) spectroscopy. RESULTS: Ten out of twenty-one stressed product samples (47.6%) showed increased particle numbers in the submicron and micron size range when compared to controls. For each product, DLS, MFI and NTA detected an increase in particle level in at least one stressed syringe (both continuous freezing and freeze-thaw), whereas HP-SEC and UV spectroscopy showed no differences between stressed and non-stressed products. CONCLUSION: TNF-α inhibitors are relatively resistant to freezing temperatures similar to storage conditions previously observed in patients' homes. However, almost half of the stressed product samples showed formation of particles in the submicron and micron size range.

Determination of the Porosity of PLGA Microparticles by Tracking Their Sedimentation Velocity Using a Flow Imaging Microscope (FlowCAM).

PURPOSE: To investigate whether particle sedimentation velocity tracking using a flow imaging microscope (FlowCAM) can be used to determine microparticle porosity. METHODS: Two different methods were explored. In the first method the sedimentation rate of microparticles was tracked in suspending media with different densities. The porosity was calculated from the average apparent density of the particles derived by inter- or extrapolation to the density of a suspending medium in which the sedimentation velocity was zero. In the second method, the microparticle size and sedimentation velocity in one suspending fluid were used to calculate the density and porosity of individual particles by using the Stokes' law of sedimentation. RESULTS: Polystyrene beads of different sizes were used for the development, optimization and validation of the methods. For both methods we found porosity values that were in excellent agreement with the expected values. Both methods were applied to determine the porosity of three PLGA microparticle batches with different porosities (between about 4 and 52%). With both methods we obtained microparticle porosity values similar to those obtained by mercury intrusion porosimetry. CONCLUSIONS: We developed two methods to determine average microparticle density and porosity by sedimentation velocity tracking, using only a few milligrams of powder.

Incorporation of bioactive glass in calcium phosphate cement: material characterization and in vitro degradation.

Calcium phosphate cements (CPCs) have been widely used as an alternative to biological grafts due to their excellent osteoconductive properties. Although degradation has been improved by using poly(D,L-lactic-co-glycolic) acid (PLGA) microspheres as porogens, the biological performance of CPC/PLGA composites is insufficient to stimulate bone healing in large bone defects. In this context, the aim of this study was to investigate the effect of incorporating osteopromotive bioactive glass (BG; up to 50 wt %) on setting properties, in vitro degradation behavior and morphological characteristics of CPC/BG and CPC/PLGA/BG. The results revealed that the initial and final setting time of the composites increased with increasing amounts of incorporated BG. The degradation test showed a BG-dependent increasing effect on pH of CPC/BG and CPC/PLGA/BG pre-set scaffolds immersed in PBS compared to CPC and CPC/PLGA equivalents. Whereas no effects on mass loss were observed for CPC and CPC/BG pre-set scaffolds, CPC/PLGA/BG pre-set scaffolds showed an accelerated mass loss compared with CPC/PLGA equivalents. Morphologically, no changes were observed for CPC and CPC/BG pre-set scaffolds. In contrast, CPC/PLGA and CPC/PLGA/BG showed apparent degradation of PLGA microspheres and faster loss of integrity for CPC/PLGA/BG pre-set scaffolds compared with CPC/PLGA equivalents. Based on the present in vitro results, it can be concluded that BG can be successfully introduced into CPC and CPC/PLGA without exceeding the setting time beyond clinically acceptable values. All injectable composites containing BG had suitable handling properties and specifically CPC/PLGA/BG showed an increased rate of mass loss. Future investigations should focus on translating these findings to in vivo applications.

Incorporation of bioactive glass in calcium phosphate cement: An evaluation.

Bioactive glasses (BGs) are known for their unique ability to bond to living bone. Consequently, the incorporation of BGs into calcium phosphate cement (CPC) was hypothesized to be a feasible approach to improve the biological performance of CPC. Previously, it has been demonstrated that BGs can successfully be introduced into CPC, with or without poly(d,l-lactic-co-glycolic) acid (PLGA) microparticles. Although an in vitro physicochemical study on the introduction of BG into CPC was encouraging, the biocompatibility and in vivo bone response to these formulations are still unknown. Therefore, the present study aimed to evaluate the in vivo performance of BG supplemented CPC, either pure or supplemented with PLGA microparticles, via both ectopic and orthotopic implantation models in rats. Pre-set scaffolds in four different formulations (1: CPC; 2: CPC/BG; 3: CPC/PLGA; and 4: CPC/PLGA/BG) were implanted subcutaneously and into femoral condyle defects of rats for 2 and 6 weeks. Upon ectopic implantation, incorporation of BG into CPC improved the soft tissue response by improving capsule and interface quality. Additionally, the incorporation of BG into CPC and CPC/PLGA showed 1.8- and 4.7-fold higher degradation and 2.2- and 1.3-fold higher bone formation in a femoral condyle defect in rats compared to pure CPC and CPC/PLGA, respectively. Consequently, these results highlight the potential of BG to be used as an additive to CPC to improve the biological performance for bone regeneration applications. Nevertheless, further confirmation is necessary regarding long-term in vivo studies, which also have to be performed under compromised wound-healing conditions.

Biomimetic modification of synthetic hydrogels by incorporation of adhesive peptides and calcium phosphate nanoparticles: in vitro evaluation of cell behavior.

The ultimate goal of this work was to develop a biocompatible and biomimetic in situ crosslinkable hydrogel scaffold with an instructive capacity for bone regenerative treatment. To this end, synthetic hydrogels were functionalized with two key components of the extracellular matrix of native bone tissue, i.e. the three-amino acid peptide sequence RGD (which is the principal integrin-binding domain responsible for cell adhesion and survival of anchorage-dependent cells) and calcium phosphate (CaP) nanoparticles in the form of hydroxyapatite (which are similar to the inorganic phase of bone tissue). Rat bone marrow osteoblast-like cells (OBLCs) were encapsulated in four different biomaterials (plain oligo(poly(ethylene glycol) fumarate) (OPF), RGD-modified OPF, OPF enriched with CaP nanoparticles and RGD-modified OPF enriched with CaP nanoparticles) and cell survival, cell spreading, proliferation and mineralized matrix formation were determined via cell viability assay, histology and biochemical analysis for alkaline phosphatase activity and calcium. This study showed that RGD peptide sequences promoted cell spreading in OPF hydrogels and hence play a crucial role in cell survival during the early stage of culture, whereas CaP nanoparticles significantly enhanced cell-mediated hydrogel mineralization. Although cell spreading and proliferation activity were inhibited, the combined effect of RGD peptide sequences and CaP nanoparticles within OPF hydrogel systems elicited a better biological response than that of the individual components. Specifically, both a sustained cell viability and mineralized matrix production mediated by encapsulated OBLCs were observed within these novel biomimetic composite systems.