ABSTRACT
Engineering activities aim to satisfy the demands of society. Not only should the economic and technological aspects be considered, but also the socio-environmental impact. In this sense, the development of composites with the incorporation of waste has been highlighted, aiming not only for better and/or cheaper materials, but also optimizing the use of natural resources. To obtain better results using industrial agro waste, we need to treat this waste to incorporate engineered composites and obtain the optimal results for each application desired. The objective of this work is to compare the effect of processing coconut husk particulates on the mechanical and thermal behavior of epoxy matrix composites, since we will need a smooth composite in the near future to be applied by brushes and sprayers with a high quality surface finish. This processing was carried out in a ball mill for 24 h. The matrix was a Bisphenol A diglycidyl ether (DGEBA)/triethylenetetramine (TETA) epoxy system. The tests that were performed were resistance to impact and compression, as well as the linear expansion test. Through this work, it can be observed that the processing of coconut husk powder was beneficial, allowing not only positive improvements to the properties of the composite, but also a better workability and wettability of the particulates, which was attributed to the change in the average size and shape of particulates. That means that the composites with processed coconut husk powders have improved impact strength (46 up to 51%) and compressive strength (88 up to 334%), in comparison with unprocessed particles.
ABSTRACT
Natural lignocellulosic fibers (NLFs) have been extensively investigated and applied as reinforcements for polymers composites owing to improved properties associated with their cost-effectiveness and their sustainable characteristics as compared to synthetic fibers. However, an intrinsic difficulty of the hydrophilic NFL adhesion to a hydrophobic polymer matrix is still a major limitation, which might be overcome via fiber surface treatments. Among the less-known NLFs, sponge gourd (Lufta cylindrica) is a promising reinforcement for polymer composites owing to its natural network of intertwined fibers. The present work investigated for the first time the influence of a chemical treatment using silane as a coupling agent for 30 wt.% sponge gourd incorporated into a polyester matrix composite. The novel composite performance was compared with that of an untreated fiber composite via X-ray diffraction (XRD), Fourier transformed infrared spectroscopy (FTIR), Charpy impact tests, and thermogravimetric analyses (TGA). The XRD results revealed that the silanization increased the crystallinity index by 37%, which attests to the effective fiber-matrix interaction stretching of the C-H bond, as observed in its FTIR band. The silanization also increased the mean impact resistance by 10%. Although the temperatures associated with the beginning of the thermal degradation by the TGA were not affected, both the silane-treated fibers and composite displayed less thermal degradation compared with the untreated fibers. The scanning electron microscopy and energy-dispersive X-ray spectroscopy (SEM/EDS) results disclosed an improved sponge gourd fiber morphology after the silanization, which caused greater adherence to the polyester matrix. These results revealed a promising novel composite compared with other NLF polymer composites in engineering applications.
ABSTRACT
Natural lignocellulosic fibers and corresponding fabrics have been gaining notoriety in recent decades as reinforcement options for polymer matrices associated with industrially applied composites. These natural fibers and fabrics exhibit competitive properties when compared with some synthetics such as glass fiber. In particular, the use of fabrics made from natural fibers might be considered a more efficient alternative, since they provide multidirectional reinforcement and allow the introduction of a larger volume fraction of fibers in the composite. In this context, it is important to understand the mechanical performance of natural fabric composites as a basic condition to ensure efficient engineering applications. Therefore, it is also important to recognize that ramie fiber exhibiting superior strength can be woven into fabric, but is the least investigated as reinforcement in strong, tough polymers to obtain tougher polymeric composites. Accordingly, this paper presents the preparation of epoxy composite containing 30 vol.% Boehmeria nivea fabric by vacuum-assisted resin infusion molding technique and mechanical behavior characterization of the prepared composite. Obtained results are explained based on the fractography studies of tested samples.
ABSTRACT
A relatively unknown natural fiber extracted from the leaves of the fique plant, native of the South American Andes, has recently shown potential as reinforcement of polymer composites for engineering applications. Preliminary investigations indicated a promising substitute for synthetic fibers, competing with other well-known natural fibers. The fabric made from fique fibers have not yet been investigated as possible composite reinforcement. Therefore, in the present work a more thorough characterization of fique fabric as a reinforcement of composites with a polyester matrix was performed. Thermal mechanical properties of fique fabric composites were determined by dynamic mechanical analysis (DMA). The ballistic performance of plain woven fique fabric-reinforced polyester matrix composites was investigated as a second layer in a multilayered armor system (MAS). The results revealed a sensible improvement in thermal dynamic mechanical behavior. Both viscoelastic stiffness and glass transition temperature were increased with the amount of incorporated fique fabric. In terms of ballistic results, the fique fabric composites present a performance similar to that of the much stronger KevlarTM as an MAS second layer with the same thickness. A cost analysis indicated that armor vests with fique fabric composites as an MAS second layer would be 13 times less expensive than a similar creation made with Kevlar™.
