Synthesis of Cs3Cu2I5 Nanocrystals in a Continuous Flow System.

Achieving the goal of generating all of the world's energy via renewable sources and significantly reducing the energy usage will require the development of novel, abundant, nontoxic energy conversion materials. Here, a cost-efficient and scalable continuous flow synthesis of Cs3Cu2I5 nanocrystals is developed as a basis for the rapid advancement of novel nanomaterials. Ideal precursor solutions are obtained through a novel batch synthesis, whose product served as a benchmark for the subsequent flow synthesis. Realizing this setup enabled a reproducible fabrication of Cs3Cu2I5 nanocrystals. The effect of volumetric flow rate and temperature on the final product's morphology and optical properties are determined, obtaining 21% quantum yield with the optimal configuration. Consequently, the size and morphology of the nanocrystals can be tuned with far more precision and in a much broader range than previously achievable. The flow setup is readily applicable to other relevant nanomaterials. It should enable a rapid determination of a material's potential and subsequently optimize its desired properties for renewable energy generation or efficient optoelectronics.

Effect of crystal facets in plasmonic catalysis.

While the role of crystal facets is well known in traditional heterogeneous catalysis, this effect has not yet been thoroughly studied in plasmon-assisted catalysis, where attention has primarily focused on plasmon-derived mechanisms. Here, we investigate plasmon-assisted electrocatalytic CO2 reduction using different shapes of plasmonic Au nanoparticles - nanocube (NC), rhombic dodecahedron (RD), and octahedron (OC) - exposing {100}, {110}, and {111} facets, respectively. Upon plasmon excitation, Au OCs doubled CO Faradaic efficiency (FECO) and tripled CO partial current density (jCO) compared to a dark condition, with NCs also improving under illumination. In contrast, Au RDs maintained consistent performance irrespective of light exposure, suggesting minimal influence of light on the reaction. Temperature experiments ruled out heat as the main factor to explain such differences. Atomistic simulations and electromagnetic modeling revealed higher hot carrier abundance and electric field enhancement on Au OCs and NCs than RDs. These effects now dominate the reaction landscape over the crystal facets, thus shifting the reaction sites when comparing dark and plasmon-activated processes. Plasmon-assisted H2 evolution reaction experiments also support these findings. The dominance of low-coordinated sites over facets in plasmonic catalysis suggests key insights for designing efficient photocatalysts for energy conversion and carbon neutralization.

Direct Synthesis of CuPd Icosahedra Supercrystals Studied by In Situ X-Ray Scattering.

Nanocrystal self-assembly into supercrystals provides a versatile platform for creating novel materials and devices with tailored properties. While common self-assembly strategies imply the use of purified nanoparticles after synthesis, conversion of chemical precursors directly into nanocrystals and then supercrystals in simple procedures has been rarely reported. Here, the nucleation and growth of CuPd icosahedra and their consecutive assembly into large closed-packed face-centered cubic (fcc) supercrystals are studied. To this end, the study simultaneously and in situ measures X-ray total scattering with pair distribution function analysis (TS-PDF) and small-angle X-ray scattering (SAXS). It is found that the supercrystals' formation is preceded by an intermediate dense phase of nanocrystals displaying short-range order (SRO). It is further shown that the organization of oleic acid/oleylamine surfactants into lamellar structures likely drives the emergence of the SRO phase and later of the supercrystals by reducing the volume accessible to particle diffusion. The supercrystals' formation as well as their disassembly are triggered by temperature. The study demonstrates that ordering of solvent molecules can be crucial in the direct synthesis of supercrystals. The study also provides a general approach to investigate novel preparation routes of supercrystals in situ and across several length scales via X-ray scattering.

pH-dependent structural transitions in cationic ionizable lipid mesophases are critical for lipid nanoparticle function.

Lipid nanoparticles (LNPs) are advanced core-shell particles for messenger RNA (mRNA) based therapies that are made of polyethylene glycol (PEG) lipid, distearoylphosphatidylcholine (DSPC), cationic ionizable lipid (CIL), cholesterol (chol), and mRNA. Yet the mechanism of pH-dependent response that is believed to cause endosomal release of LNPs is not well understood. Here, we show that eGFP (enhanced green fluorescent protein) protein expression in the mouse liver mediated by the ionizable lipids DLin-MC3-DMA (MC3), DLin-KC2-DMA (KC2), and DLinDMA (DD) ranks MC3 ≥ KC2 > DD despite similar delivery of mRNA per cell in all cell fractions isolated. We hypothesize that the three CIL-LNPs react differently to pH changes and hence study the structure of CIL/chol bulk phases in water. Using synchrotron X-ray scattering a sequence of ordered CIL/chol mesophases with lowering pH values are observed. These phases show isotropic inverse micellar, cubic Fd3m inverse micellar, inverse hexagonal [Formula: see text] and bicontinuous cubic Pn3m symmetry. If polyadenylic acid, as mRNA surrogate, is added to CIL/chol, excess lipid coexists with a condensed nucleic acid lipid [Formula: see text] phase. The next-neighbor distance in the excess phase shows a discontinuity at the Fd3m inverse micellar to inverse hexagonal [Formula: see text] transition occurring at pH 6 with distinctly larger spacing and hydration for DD vs. MC3 and KC2. In mRNA LNPs, DD showed larger internal spacing, as well as retarded onset and reduced level of DD-LNP-mediated eGFP expression in vitro compared to MC3 and KC2. Our data suggest that the pH-driven Fd3m-[Formula: see text] transition in bulk phases is a hallmark of CIL-specific differences in mRNA LNP efficacy.

Photodegradation of CuBi2 O4 Films Evidenced by Fast Formation of Metallic Bi using Operando Surface-sensitive X-ray Scattering.

CuBi2 O4 has recently emerged as a promising photocathode for photo-electrochemical (PEC) water splitting. However, its fast degradation under operation currently poses a limit to its application. Here, we report a novel method to study operando the semiconductor-electrolyte interface during PEC operation by surface-sensitive high-energy X-ray scattering. We find that a fast decrease in the generated photocurrents correlates directly with the formation of a metallic Bi phase. We further show that the slower formation of metallic Cu, as well as the dissolution of the electrode in contact with the electrolyte, further affect the CuBi2 O4 activity and morphology. Our study provides a comprehensive picture of the degradation mechanisms affecting CuBi2 O4 electrodes under operation and poses the methodological basis to investigate the photocorrosion processes affecting a wide range of PEC materials.

Lead-Free, Luminescent Perovskite Nanocrystals Obtained through Ambient Condition Synthesis.

Heterovalently substituting toxic lead is an increasingly popular design strategy to obtain environmentally sustainable variants of the exciting material class of halide perovskites. Perovskite nanocrystals (NCs) obtained through solution-based methods exhibit exceedingly high optical quality. Unfortunately, most of these synthesis routes still require reaction under inert gas and at very high temperatures. Herein a novel synthesis routine for lead-free double perovskite (LFDP) NCs is presented. An approach based upon the hot injection and ligand-assisted reprecipitation (LARP) methods to achieve a low-temperature and ambient atmosphere-based synthesis for manganese-doped Cs2 NaBiCl6 NCs is presented. Mn incorporation is critical for the otherwise non-emissive material, with a 9:1 Bi:Mn precursor ratio maximizing the bright orange photoluminescence (PL) and quantum yield (QY). Higher synthesis temperatures slightly increase the material's performance, yet NCs synthesized at room temperature are still emissive, highlighting the versatility of the synthetic approach. While the material's indirect bandgap limits its appeal for optoelectronics, this feature could benefit photocatalysis due to longer carrier lifetimes. Moreover, the developed synthesis is facile and can rapidly be adapted to other more viable material compositions and up-scaled to realize applications directly.

Elucidating the Origins of High Preferential Crystal Orientation in Quasi-2D Perovskite Solar Cells.

Incorporating large organic cations to form 2D and mixed 2D/3D structures significantly increases the stability of perovskite solar cells. However, due to their low electron mobility, aligning the organic sheets to ensure unimpeded charge transport is critical to rival the high performances of pure 3D systems. While additives such as methylammonium chloride (MACl) can enable this preferential orientation, so far, no complete description exists explaining how they influence the nucleation process to grow highly aligned crystals. Here, by investigating the initial stages of the crystallization, as well as partially and fully formed perovskites grown using MACl, the origins underlying this favorable alignment are inferred. This mechanism is studied by employing 3-fluorobenzylammonium in quasi-2D perovskite solar cells. Upon assisting the crystallization with MACl, films with a degree of preferential orientation of 94%, capable of withstanding moisture levels of 97% relative humidity for 10 h without significant changes in the crystal structure are achieved. Finally, by combining macroscopic, microscopic, and spectroscopic studies, the nucleation process leading to highly oriented perovskite films is elucidated. Understanding this mechanism will aid in the rational design of future additives to achieve more defect tolerant and stable perovskite optoelectronics.

In situ small-angle X-ray scattering reveals strong condensation of DNA origami during silicification.

Silicification of DNA origami structures increases their stability and provides chemical protection. Yet, it is unclear whether the whole DNA framework is embedded or if silica just forms an outer shell and how silicification affects the origami's internal structure. Employing in situ small-angle X-ray scattering (SAXS), we show that addition of silica precursors induces substantial condensation of the DNA origami at early reaction times by almost 10 %. Subsequently, the overall size of the silicified DNA origami increases again due to increasing silica deposition. We further identify the SAXS Porod invariant as a reliable, model-free parameter for the evaluation of the amount of silica formation at a given time. Contrast matching of the DNA double helix Lorentzian peak reveals silica growth also inside the origami. The less polar silica forming within the origami structure, replacing more than 40 % of the internal hydration water, causes a hydrophobic effect: condensation. DNA origami objects with flat surfaces show a strong tendency towards aggregation during silicification, presumably driven by the same entropic forces causing condensation. Maximally condensed origami displayed thermal stability up to 60 °C. Our studies provide insights into the silicification reaction allowing for the formulation of optimized reaction protocols.

Exciton Dynamics in MoS2-Pentacene and WSe2-Pentacene Heterojunctions.

We measured the exciton dynamics in van der Waals heterojunctions of transition metal dichalcogenides (TMDCs) and organic semiconductors (OSs). TMDCs and OSs are semiconducting materials with rich and highly diverse optical and electronic properties. Their heterostructures, exhibiting van der Waals bonding at their interfaces, can be utilized in the field of optoelectronics and photovoltaics. Two types of heterojunctions, MoS2-pentacene and WSe2-pentacene, were prepared by layer transfer of 20 nm pentacene thin films as well as MoS2 and WSe2 monolayer crystals onto Au surfaces. The samples were studied by means of transient absorption spectroscopy in the reflectance mode. We found that A-exciton decay by hole transfer from MoS2 to pentacene occurs with a characteristic time of 21 ± 3 ps. This is slow compared to previously reported hole transfer times of 6.7 ps in MoS2-pentacene junctions formed by vapor deposition of pentacene molecules onto MoS2 on SiO2. The B-exciton decay in WSe2 shows faster hole transfer rates for WSe2-pentacene heterojunctions, with a characteristic time of 7 ± 1 ps. The A-exciton in WSe2 also decays faster due to the presence of a pentacene overlayer; however, fitting the decay traces did not allow for the unambiguous assignment of the associated decay time. Our work provides important insights into excitonic dynamics in the growing field of TMDC-OS heterojunctions.

3D-printed SAXS chamber for controlled in situ dialysis and optical characterization.

3D printing changes the scope of how samples can be mounted for small-angle X-ray scattering (SAXS). In this paper a 3D-printed X-ray chamber, which allows for in situ exchange of buffer and in situ optical transmission spectroscopy, is presented. The chamber is made of cyclic olefin copolymers (COC), including COC X-ray windows providing ultra-low SAXS background. The design integrates a membrane insert for in situ dialysis of the 100 µl sample volume against a reservoir, which enables measurements of the same sample under multiple conditions using an in-house X-ray setup equipped with a 17.4 keV molybdenum source. The design's capabilities are demonstrated by measuring reversible structural changes in lipid and polymer systems as a function of salt concentration and pH. In the same chambers optical light transmission spectroscopy was carried out measuring the optical turbidity of the mesophases and local pH values using pH-responsive dyes. Microfluidic exchange and optical spectroscopy combined with in situ X-ray scattering enables vast applications for the study of responsive materials.

Optical Membrane Control with Red Light Enabled by Red-Shifted Photolipids.

Photoswitchable phospholipids, or "photolipids", that harbor an azobenzene group in their lipid tails are versatile tools to manipulate and control lipid bilayer properties with light. So far, the limited ultraviolet-A/blue spectral range in which the photoisomerization of regular azobenzene operates has been a major obstacle for biophysical or photopharmaceutical applications. Here, we report on the synthesis of nano- and micrometer-sized liposomes from tetra-ortho-chloro azobenzene-substituted phosphatidylcholine (termed red-azo-PC) that undergoes photoisomerization on irradiation with tissue-penetrating red light (≥630 nm). Photoswitching strongly affects the fluidity and mechanical properties of lipid membranes, although small-angle X-ray scattering and dynamic light scattering measurements reveal only a minor influence on the overall bilayer thickness and area expansion. By controlling the photostationary state and the photoswitching efficiency of red-azo-PC for specific wavelengths, we demonstrate that shape transitions such as budding or pearling and the division of cell-sized vesicles can be achieved. These results emphasize the applicability of red-azo-PC as a nanophotonic tool in synthetic biology and for biomedical applications.

Modular Assembly of Vibrationally and Electronically Coupled Rhenium Bipyridine Carbonyl Complexes on Silicon.

Hybrid inorganic/organic heterointerfaces are promising systems for next-generation photocatalytic, photovoltaic, and chemical-sensing applications. Their performance relies strongly on the development of robust and reliable surface passivation and functionalization protocols with (sub)molecular control. The structure, stability, and chemistry of the semiconductor surface determine the functionality of the hybrid assembly. Generally, these modification schemes have to be laboriously developed to satisfy the specific chemical demands of the semiconductor surface. The implementation of a chemically independent, yet highly selective, standardized surface functionalization scheme, compatible with nanoelectronic device fabrication, is of utmost technological relevance. Here, we introduce a modular surface assembly (MSA) approach that allows the covalent anchoring of molecular transition-metal complexes with sub-nanometer precision on any solid material by combining atomic layer deposition (ALD) and selectively self-assembled monolayers of phosphonic acids. ALD, as an essential tool in semiconductor device fabrication, is used to grow conformal aluminum oxide activation coatings, down to sub-nanometer thicknesses, on silicon surfaces to enable a selective step-by-step layer assembly of rhenium(I) bipyridine tricarbonyl molecular complexes. The modular surface assembly of molecular complexes generates precisely structured spatial ensembles with strong intermolecular vibrational and electronic coupling, as demonstrated by infrared spectroscopy, photoluminescence, and X-ray photoelectron spectroscopy analysis. The structure of the MSA can be chosen to avoid electronic interactions with the semiconductor substrate to exclusively investigate the electronic interactions between the surface-immobilized molecular complexes.

X-ray studies bridge the molecular and macro length scales during the emergence of CoO assemblies.

The key to fabricating complex, hierarchical materials is the control of chemical reactions at various length scales. To this end, the classical model of nucleation and growth fails to provide sufficient information. Here, we illustrate how modern X-ray spectroscopic and scattering in situ studies bridge the molecular- and macro- length scales for assemblies of polyhedrally shaped CoO nanocrystals. Utilizing high energy-resolution fluorescence-detected X-ray absorption spectroscopy, we directly access the molecular level of the nanomaterial synthesis. We reveal that initially Co(acac)3 rapidly reduces to square-planar Co(acac)2 and coordinates to two solvent molecules. Combining atomic pair distribution functions and small-angle X-ray scattering we observe that, unlike a classical nucleation and growth mechanism, nuclei as small as 2 nm assemble into superstructures of 20 nm. The individual nanoparticles and assemblies continue growing at a similar pace. The final spherical assemblies are smaller than 100 nm, while the nanoparticles reach a size of 6 nm and adopt various polyhedral, edgy shapes. Our work thus provides a comprehensive perspective on the emergence of nano-assemblies in solution.

X-ray-Based Techniques to Study the Nano-Bio Interface.

X-ray-based analytics are routinely applied in many fields, including physics, chemistry, materials science, and engineering. The full potential of such techniques in the life sciences and medicine, however, has not yet been fully exploited. We highlight current and upcoming advances in this direction. We describe different X-ray-based methodologies (including those performed at synchrotron light sources and X-ray free-electron lasers) and their potentials for application to investigate the nano-bio interface. The discussion is predominantly guided by asking how such methods could better help to understand and to improve nanoparticle-based drug delivery, though the concepts also apply to nano-bio interactions in general. We discuss current limitations and how they might be overcome, particularly for future use in vivo.

Nanostructured amorphous gallium phosphide on silica for nonlinear and ultrafast nanophotonics.

Nanophotonics based on high refractive index dielectrics relies on appreciable contrast between the indices of designed nanostructures and their immediate surrounding, which can be achieved by the growth of thin films on low-index substrates. Here we propose the use of high index amorphous gallium phosphide (a-GaP), fabricated by radio-frequency sputter deposition, on top of a low refractive index glass substrate and thoroughly examine its nanophotonic properties. Spectral ellipsometry of the amorphous material demonstrates the optical properties to be considerably close to crystalline gallium phosphide (c-GaP), with low-loss transparency for wavelengths longer than 650 nm. When nanostructured into nanopatches, the second harmonic (SH) response of an individual a-GaP patch is characterized to be more than two orders of magnitude larger than the as-deposited unstructured film, with an anapole-like resonant behavior. Numerical simulations are in good agreement with the experimental results over a large spectral and geometrical range. Furthermore, by studying individual a-GaP nanopatches through non-degenerate pump-probe spectroscopy with sub-10 fs pulses, we find a more than 5% ultrafast modulation of the reflectivity that is accompanied by a slower decaying free carrier contribution, caused by absorption. Our investigations reveal a potential for a-GaP as an adequate inexpensive and CMOS-compatible material for nonlinear nanophotonic applications as well as for photocatalysis.

Chiral Assembly of Gold-Silver Core-Shell Plasmonic Nanorods on DNA Origami with Strong Optical Activity.

The spatial organization of metal nanoparticles has become an important tool for manipulating light in nanophotonic applications. Silver nanoparticles, particularly silver nanorods, have excellent plasmonic properties but are prone to oxidation and are therefore inherently unstable in aqueous solutions and salt-containing buffers. Consequently, gold nanoparticles have often been favored, despite their inferior optical performance. Bimetallic, i.e., gold-silver core-shell nanoparticles, can resolve this issue. We present a method for synthesizing highly stable gold-silver core-shell NRs that are instantaneously functionalized with DNA, enabling chiral self-assembly on DNA origami. The silver shell gives rise to an enhancement of plasmonic properties, reflected here in strongly increased circular dichroism, as compared to pristine gold nanorods. Gold-silver nanorods are ideal candidates for plasmonic sensing with increased sensitivity as needed in pathogen RNA or antibody testing for nonlinear optics and light-funneling applications in surface enhanced Raman spectroscopy. Furthermore, the control of interparticle orientation enables the study of plasmonic phenomena, in particular, synergistic effects arising from plasmonic coupling of such bimetallic systems.

Polymer Lamellae as Reaction Intermediates in the Formation of Copper Nanospheres as Evidenced by In†Situ X-ray Studies.

The classical nucleation theory (CNT) is the most common theoretical framework used to explain particle formation. However, nucleation is a complex process with reaction pathways which are often not covered by the CNT. Herein, we study the formation mechanism of copper nanospheres using in situ X-ray absorption and scattering measurements. We reveal that their nucleation involves coordination polymer lamellae as pre-nucleation structures occupying a local minimum in the reaction energy landscape. Having learned this, we achieved a superior monodispersity for Cu nanospheres of different sizes. This report exemplifies the importance of developing a more realistic picture of the mechanism involved in the formation of inorganic nanoparticles to develop a rational approach to their synthesis.

A Lipid Photoswitch Controls Fluidity in Supported Bilayer Membranes.

Supported lipid bilayer (SLB) membranes are key elements to mimic membrane interfaces on a planar surface. Here, we demonstrate that azobenzene photolipids (azo-PC) form fluid, homogeneous SLBs. Diffusion properties of azo-PC within SLBs were probed by fluorescence microscopy and fluorescence recovery after photobleaching. At ambient conditions, we find that the trans-to-cis isomerization causes an increase of the diffusion constant by a factor of two. Simultaneous excitation with two wavelengths and variable intensities furthermore allows to adjust the diffusion constant D continuously. X-ray reflectometry and small-angle scattering measurements reveal that membrane photoisomerization results in a bilayer thickness reduction of ∼0.4 nm (or 10%). While thermally induced back-switching is not observed, we find that the trans bilayer fluidity is increasing with higher temperatures. This change in diffusion constant is accompanied by a red-shift in the absorption spectra. Based on these results, we suggest that the reduced diffusivity of trans-azo-PC is controlled by intermolecular interactions that also give rise to H-aggregate formation in bilayer membranes.

Polymer Nanoreactors Shield Perovskite Nanocrystals from Degradation.

Halide perovskite nanocrystals (NCs) have shown impressive advances, exhibiting optical properties that outpace conventional semiconductor NCs, such as near-unity quantum yields and ultrafast radiative decay rates. Nevertheless, the NCs suffer even more from stability problems at ambient conditions and due to moisture than their bulk counterparts. Herein, we report a strategy of employing polymer micelles as nanoreactors for the synthesis of methylammonium lead trihalide perovskite NCs. Encapsulated by this polymer shell, the NCs display strong stability against water degradation and halide ion migration. Thin films comprising these NCs exhibit a more than 15-fold increase in lifespan in comparison to unprotected NCs in ambient conditions and even survive over 75 days of complete immersion in water. Furthermore, the NCs, which exhibit quantum yields of up to 63% and tunability of the emission wavelength throughout the visible range, show no signs of halide ion exchange. Additionally, heterostructures of MAPI and MAPBr NC layers exhibit efficient Förster resonance energy transfer (FRET), revealing a strategy for optoelectronic integration.

Probing the Interface Structure of Adhering Cells by Contrast Variation Neutron Reflectometry.

Cellular adhesion is a central element in tissue mechanics, biological cell-cell signaling, and cell motility. In this context, the cell-substrate distance has been investigated in the past by studying natural cells and biomimetic cell models adhering on solid substrates. The amount of water in the membrane substrate gap, however, is difficult to determine. Here, we present a neutron reflectivity (NR) structural study of confluent epithelial cell monolayers on silicon substrates. In order to ensure valid in vitro conditions, we developed a cell culture sample chamber allowing us to grow and cultivate cells under proper cell culture conditions while performing in vitro neutron reflectivity measurements. The cell chamber also enabled perfusion with cell medium and hence allowed for contrast variation in situ by sterile exchange of buffer with different H2O-to-D2O ratio. Contrast variation reduces the ambiguity of data modeling for determining the thickness and degree of hydration of the interfacial cleft between the adherent cells and the substrate. Our data suggest a three-layer interfacial organization. The first layer bound to the silicon surface interface is in agreement with a very dense protein film with a thickness of 9 ± 2 nm, followed by a highly hydrated 24 ± 4 nm thick layer, and a several tens of nanometers thick layer attributed to the composite membrane. Hence, the results provide clear evidence of a highly hydrated intermediate region between the composite cell membrane and the substrate, reminiscent of the basal lamina.