Stress distribution on implant- supported zirconia crown of maxillary first molar: effect of oblique load on natural and antagonist tooth.

This study evaluated the stress distribution on an implant-supported zirconia crown of a mandibular first molar subjected to oblique loading by occlusal contact with the natural maxillary first molar by using the 3D finite element method. Two virtual models were made to simulate the following situations: (1) occlusion between maxillary and mandibular natural first molars; (2) occlusion between zirconia implant-supported ceramic crown on a mandibular first molar and maxillary natural first molar. The models were designed virtually in a modeling program or CAD (Computer Aided Design) (Rhinoceros). An oblique load of 100 N was uniformly applied to the zirconia framework of the crown. The results were obtained by the Von Mises criterion of stress distribution. Replacement of the mandibular tooth by an implant caused a slight increase in stress on portions of the maxillary tooth roots. The crown of the maxillary model in occlusion with natural antagonist tooth showed 12% less stress when compared with the maxillary (model in occlusion with the) implant-supported crown. The mandibular crown of the implant show 35% more stress when compared with the mandibular antagonist crown on the natural tooth. The presence of the implant to replace the mandibular tooth increased the stresses on the maxillary tooth, especially in the region of the mesial and distal buccal roots.

Influence of Abutment Design on Biomechanical Behavior to Support a Screw-Retained 3-Unit Fixed Partial Denture.

This study aimed to evaluate the biomechanical behavior of Morse taper implants using different abutments (CMN abutment [(CMN Group] and miniconical abutments [MC Group]), indicated to support a screw-retained 3-unit fixed partial denture. For the in vitro test, polyurethane blocks were fabricated for both groups (n = 10) and received three implants in the "offset" configuration and their respective abutments (CMN or MC) with a 3-unit fixed partial denture. Four strain gauges were bonded to the surface of each block. For the finite element analysis, 3D models of both groups were created and exported to the analysis software to perform static structural analysis. All structures were considered homogeneous, isotropic, and elastic. The contacts were considered non-linear with a friction coefficient of 0.3 between metallic structures and considered bonded between the implant and substrate. An axial load of 300 N was applied in three points (A, B, and C) for both methods. The microstrain and the maximum principal stress were considered as analysis criteria. The obtained data were submitted to the Mann-Whitney, Kruskal-Wallis, and Dunn's multiple comparison test (α = 5%). The results obtained by strain gauge showed no statistical difference (p = 0.879) between the CMN (645.3 ± 309.2 µÎµ) and MC (639.3 ± 278.8 µÎµ) and allowed the validation of computational models with a difference of 6.3% and 6.4% for the microstrains in the CMN and MC groups, respectively. Similarly, the results presented by the computational models showed no statistical difference (p = 0.932) for the CMN (605.1 ± 358.6 µÎµ) and MC (598.7 ± 357.9 µÎµ) groups. The study concluded that under favorable conditions the use of CMN or MP abutments to support a fixed partial denture can be indicated.

Metal Alloys in Dentistry: An Outdated Material or Required for Oral Rehabilitation?

ABSTRACT: The present study aims to describe through a literature review, the main types of noble and non-noble alloys in dentistry looking to identify the adhesion mechanisms, compositions and mechanical properties, and its applicability as a rehabilitation resource nowadays. A bibliographic search was conducted in the main health databases PUBMED (www.pubmed.gov) and Scholar Google (www.scholar.google.com.br), in which studies published from 1971 to 2021 were collected. Laboratory studies, case reports, systematic and literature reviews, which were developed in living individuals. Articles that did not deal with metal alloys and its use in dentistry were excluded. Through the review, it was possible to ver ify that all works presented the metal alloys and their main properties, indicating that they are divided into three main types: hi gh noble alloys, noble alloys and base metal alloys differing in their levels of constituent noble metals. Several alloys and meta ls are available for the dental market each presenting advantages and disadvantages, mainly based on its specific composition.Continuous research and development are resulting in the production of new technologies and products, giving dental surgeons even more options in the design and manufacture of restorations using metal alloys and understanding that these resources will still be viable alternatives in oral rehabilitations. However, further studies on metal alloys are needed to better understand this subject.

RESUMEN: El presente trabajo tuvo como objetivo describir a través de una revisión de la literatura, los principales tipos de aleaciones nobles y no nobles utilizados en odontología buscando identificar los mecanismos de adhesión, composiciones y propiedades mecánicas, así como reflejar su aplicabilidad como recurso rehabilitador en la actualidad. Realizamos una búsqueda bibliográfica em las principales bases de datos de salud PUBMED (www.pubmed.gov) y Scholar Google (www.scholar.google.com.br), en la que se recopilaron estudios publicados desde 1971 hasta 2021. Estudios de laboratorio, informes de casos, revisiones sistemáticas y bibliográficas, que se desarrollaron en individuos vivos. Sin embargo, se excluyeron los artículos que no trataban sobre aleaciones metálicas y su uso en odontología. Se pudo observar que todos los trabajos presentaban las aleaciones metálicas y sus principales propiedades indicando que se estas dividen en tres tipos principales: aleaciones altamente nobles, aleaciones nobles y aleaciones de metales base que difierenen sus niveles de metales nobles constituyentes. Hay varias aleaciones y metales disponibles para el mercado dental, cada uno presenta ventajas y desventajas, principalmente en función de su composición específica. La investigación y el desarrollo continuo están dando como resultado la producción de nuevas tecnologías y productos, brindando a los cirujanos dentistas aún más opciones en el diseño y fabricación de las restauraciones, utilizando aleaciones metálicas y, permite concluir que estos recursos seguirán siendo alternativas viables en los tratamientos de rehabilitación. Sin embargo, se necesitan más estudios sobre el tema abordado en el trabajo, para una comprensión más profunda del tema.

Open tray impression technique using a silica-nylon mesh for splitting implants: a case report / Técnica de moldagem de moldeira aberta com malha de sílica-nylon para esplintagem de implantes: relato de caso clínico / La técnica de impresiones en cubeta abierta con malla de sílice-nylon para ferulización de implantes: reporte de caso clínico

This article describes an alternative open tray technique for implant impressions using a novel reinforced silica-nylon mesh covered with acrylic resin as a splitting system in assembling the abutment complex. The purpose of the procedure is to simplify the technique and improve the resin contraction during clinical procedure, and also optimizes and reduces the chairside time for the patient. The clinical report was supported by an in vitrostudy where an analysis tool, Strain Gauge Analysis, was used to prove the clinical effectiveness of the technique. The peri-implant strain was determined on polyurethane casts with the torqued prosthesis, and statistically there was no difference in strain under torque of transfers or in the final prosthesis. The nylon mesh attached to acrylic resin represents a promising option for open tray impression technique, creating a resistant union to transfer in an excellent procedure time(AU)

Este artigo descreve uma alternativa para a técnica de moldeira aberta para moldagem de implantes utilizando uma nova malha de reforço de sílica-nylon coberta por resina acrílica para ferulização dos componentes protéticos. O propósito deste procedimento é simplificar a técnica e compensar a contração da resina durante os procedimentos clínicos, e também otimizar e reduzir o tempo de atendimento do paciente. O relato de caso foi amparado com um estudo in vitroonde uma ferramenta de análise de extensometria, Análise de Strain Gauge, foi utilizada para avaliar a efetividade clínica da técnica. A deformação peri-implantar foi determinada nas bases de poliuretano com a prótese instalada, e estatisticamente não houve diferença estatística na deformação nos torques dos transferentes ou na prótese final. A malha de nylon unida à resina acrílica representa uma opção promissora para a técnica de moldagem com moldeira aberta, criando uma união resistente aos transferentes em um excelente tempo clínico(AU)

Este estudio describe una técnica alternativa de cubeta abierta para impresiones de implantes utilizando una nueva malla de sílice-nylon cubierta con resina acrílica como un sistema de ferulización en montaje del complejo de pilares. El objetivo del procedimiento es simplificar la técnica y mejorar la contracción de la resina durante el procedimiento clínico y también optimiza y reduce el tiempo de atención al paciente. El relato clínico fue respaldado por un estudio in vitro en el que se utilizó unaherramienta de análisis, Análisis de Galgas Extensométricas, para probar la efectividad clínica de la técnica. La deformación periimplantaria se determinó en moldes de poliuretano con la prótesis apretada, y estadísticamente no hubo diferencia en la deformación del torque de los postes o en la prótesis final. La malla de nylon unida a la resina acrílica representa una opción prometedora para la técnica de impresión en cubeta abierta, creando una unión resistente para transferir en un excelente tiempo de procedimiento(AU)

Influence of the dental implant number and load direction on stress distribution in a 3-unit implant-supported fixed dental prosthesis.

BACKGROUND: The choice between 2 or 3 implants to support a 3-unit implant-supported fixed dental prosthesis (FDP) still generates doubt in clinical practice. OBJECTIVES: The aim of this study was to evaluate stress distribution in 3-unit implant-supported FDPs according to the implant number and load direction. MATERIAL AND METHODS: A numerical simulation was performed to analyze stress and strain according to the implant number (2 or 3) and load direction (axial or oblique). A model of a jaw was created by means of the modeling software Rhinoceros, v. 5.0 SR8. External hexagon implants, micro-conical abutments and screws were also modeled. The final geometries were exported to the computer-aided engineering (CAE) software Ansys, v. 17.2, and all materials were considered homogeneous, isotropic and elastic. Different load directions were applied for each model (300 N) at the center of the prosthesis. RESULTS: The von Mises stress and strain values were obtained for the titanium structures and the bone, respectively. The implant number influenced the prosthesis biomechanics, with higher stress and strain concentrations when 2 implants were simulated. The oblique load also affected the mechanical response, showing higher stress and strain in comparison with the axial load, regardless of the implant number. CONCLUSIONS: It was concluded that for a 3-unit implant-supported FDP, a greater number of implants associated with axial loads can result in a better mechanical response during chewing.

Effect of Framework Type on the Biomechanical Behavior of Provisional Crowns: Strain Gauge and Finite Element Analyses.

The aim of this study was to evaluate the effects of different frameworks on the biomechanical behavior of implant-supported provisional single crowns to indicate or not the use of plastic framework as infrastructure. For finite element analysis, a hemi-jaw stone model was scanned and modeled with an external hexagon implant. A framework was screwed onto the implant and a crown was constructed over it. The set was made in triplicate according to framework type: plastic, cobalt-chromium (CoCr), and titanium. Models were exported in volumetric format to analysis software where structures were considered isotropic, linear, elastic, and homogeneous. Axial loads (100, 200, and 300 N) were applied to the fossa bottom, and the system's fixation occurred on the bone base. For strain-gauge analysis, the same hemi-jaw model was built in polyurethane and an implant was placed on it. Three crowns were made, each one with a different framework. Four strain gauges were glued around the implant to obtain microstrain values. The data were analyzed by three-way analysis of variance (ANOVA) and Tukey tests (P < .05). Finite element analysis exhibited microstrain results for bone, von Mises stress values for the implant and screw, and maximum principal stress values for the crown. For computational method, as the applied load increased, so did the stress generated. Titanium frameworks concentrated more stress in the crown and bone, while plastic ones concentrated more in the implant and screw. ANOVA showed that the higher the load value and the framework elastic modulus, the higher the generated microstrain in bone. It can be concluded that all evaluated framework types can be used in the manufacturing of provisional crowns.

Evaluation of peri-implant condition in periodontally compromised patients.

AIMS: The aim of the study is to evaluate the profile of peri-implant tissues in periodontally compromised patients. SETTINGS AND DESIGN: In vivo - cross sectional study design. MATERIALS AND METHODS: Fifty-eight implants were evaluated, clinically and radiographically, installed in seven individuals treated by the same team of professionals, during the years 1997 and 2005 in a private dental clinic in Vitória, ES, Brazil; that time of data collection, all implants were at least 10 years of functional loading. The variables related to the dental implants evaluated were: visible Plaque Index, Gingival Bleeding Index (GBI), probing pocket depth, bleeding on probing, and bone level, to relate them to the classification of dental implants. STATISTICAL ANALYSIS USED: The Chi-square and Kruskal-Wallis test were adopted. RESULTS: The total of 58 implants were classified: 11 (18.9%) as healthy and 12 (20.7%) as clinically stable. The other 35 implants (60.4%) had some type of peri-implant inflammation, 20 of them (34.5%) were diagnosed with peri-implant mucositis and 15 (25.9%) with peri-implantitis. Among the variables studied, the results showed statistically significant differences for implant location (P = 0.001) and GBI (P = 0.03). Most of the maxillary implants (85.7%) were classified for some type of peri-implant disease. For the implants which resulted in Score 1 for GBI, most of them (75.0%) were also classified for some type of peri-implant disease. CONCLUSIONS: Dental implants placed in periodontally compromised patients may have high long-term survival rates. However, most implants were classified with some type of peri-implant inflammation.

Comparative in vivo study of alloy titanium implants with two different surfaces: biomechanical and SEM analysis.

OBJECTIVES: The purpose of this study was to evaluate the biomechanical behavior of the interface formed between bone and implants with machined surfaces (MS) and those modified by Al2O3 sandblasting and acid etching (SBAS). MATERIALS AND METHODS: Before surgery, topographic characterization was performed by SEM-EDX and by mean roughness measurements. Ten Albinus rabbits received randomly 20 Ti-6Al-4V implants on its right and left tibiae, with one implant placed in each tibia. After implant insertion, the implant stability quotient (ISQ) was measured by means of resonance frequency analysis (RFA). After 3 and 6 weeks, the ISQ was again measured, followed by torque removal measurements. Analysis of variance and Tukey tests were used to analyze the data. The surface of the implants removed was evaluated by SEM-EDX. Immunohistochemical analysis of osteopontin (OPN) and osteocalcin (OC) protein was performed in bone tissue. RESULTS: The topographic characterization showed differences between the analyzed surfaces, and the mean roughness values of SBAS group were statistically higher than MS. Overall, higher statistically significant ISQ values were observed in the SBAS group compared to the MS group (p = 0.012). The intra-group comparison of ISQ values in the SBAS group showed statistically significant differences between 0 and 3 weeks (p = 0.032) and 0 and 6 weeks (p = 0.003). The torque removal measurements of group SBAS were statistically higher when compared with the torque removal measurements of group MS in the time intervals of 3 weeks (p = 0.002) and 6 weeks (p < 0.001). SEM-EDX of the implant surfaces removed in SBAS group showed greater bone tissue covering and mean values atomic in percentage of Ca, P, and O statistically superior (p < 0.05) than MS group. Immunohistochemical reactions showed intense OC immunolabeling at 6 weeks postoperative for SBAS group. CONCLUSIONS: The topographical modifications made in group SBAS allowed a better mechanical interlocking between the implant and bone tissue.

Application of Bio-Oss in tissue regenerative treatment prior to implant installation: literature review / Aplicação de Bio-Oss em tratamento regenerativo tecidual previamente a instalação de implante: revisão da literatura

Objetivo: Bio-Oss is a xenogene bone graft in which all organic components are removed while retaining their natural mineral architecture. Therefore, the aim of this study was to evaluate, through a literature review, the benefits of using Bio-Oss for tissue regenerative treatment prior to implant placement. Materials and methods: a search was performed in Pubmed (Medline) in order to identify articles published in English between January 1, 2000 and June 31, 2018, where the Bio-Oss graft was used prior to implantation of implants in humans. A total of 40 studies were selected for detailed analysis. From this analysis, 18 articles were identified for inclusion in this review. Results: the articles analyzed in the review showed several beneficial effects of this xenograft, such as: positive osteoconductive properties, recovery of bone heights at sites with severe atrophies, slow xenograft reabsorption suggesting long term stability, survival rates and success of implants placed in grafted sites ranging from 91 to 100% in several studies. Conclusion: the use of bio-oss as a bone substitute is a viable alternative in the placement before dental implants, being used in clinical practice and with proved efficacy in several studies, due to its similarity with the bone and its high level of osteoconductivity (AU)

Objetivo: o Bio-Oss é um substituído ósseo xenógeno em que são removidos todos os componentes orgânicos, mantendo sua arquitetura natural. Assim, este trabalho teve como foco avaliar através de uma revisão de literatura os benefícios do uso do Bio-Oss para tratamento regenerativo tecidual previamente a instalação de implantes. Materiais e métodos: realizouse uma busca no Pubmed (Medline) com intuito de se identificar artigos publicados em inglês entre 1 de janeiro de 2000 e 31 de junho de 2018, em que se utilizava o enxerto Bio-Oss previamente a instalação de implantes em humanos. Foram selecionados 40 estudos completos para uma análise detalhada. A partir dessa análise foram identificados 18 artigos para inclusão nessa revisão. Resultados: os artigos analisados na revisão mostraram diversos efeitos benéficos desse xenoenxerto, como: propriedades osteocondutoras positivas, recuperação de alturas ósseas em locais com atrofias graves, reabsorção lenta do xenoenxerto sugerindo estabilidade a longo prazo, taxas de sobrevivência e sucesso de implantes colocados em locais enxertados variando de 91 a 100% em diversas pesquisas. Conclusão: a utilização do biooss como substituto ósseo é uma alternativa viável na colocação previamente ao implante dentário, sendo utilizado na prática clínica e comprovado em diversos estudos sua eficácia, devido sua similaridade com o osso natural e seu alto grau de osteocondutividade (AU)

Preservation of Dental Sockets Filled with Composite Bovine Bone. A Single-Blind Randomized Clinical Trial.

The purpose of this study was to evaluate the preservation of alveolar dimensions in human fresh extraction sockets filled with a composite bovine bone graft by means of design of single-blind randomized clinical trial. Forty participants had monoradicular teeth extracted (one teeth in each participant), and after were randomly divided into 2 groups: individuals whose fresh sockets were filled with the composite heterologous bone graft (Biomaterial Group), or with blood clot (Control Group). After extraction, the fresh sockets were measured at their greatest mesiodistal (MD) and bucco-lingual/palatal (BL/P) distance. Primary closure of the soft tissue was performed with a fibro-mucosal plug. After 120 post-operative days, the re-entry procedure was performed and the largest MD and BL/P measurements were again obtained to calculate the remodeling of the alveolar bone measured in percentage. In the biomaterial group, a percentage reduction of 1.62% and 3.29% in the MD and BL/P dimensions was observed 120 days after the extractions, whereas a reduction of 4.97% and 7.18% in the MD and BL/P dimensions occurred in the control group. There was a statistically significant difference (p<0.05) between the two groups for the bucco-palatal and mesiodistal measurements in the maxilla. In view of the results obtained, it can be concluded that composite bovine bone graft limited but did not impede alveolar bone remodeling.

Preservation of dental sockets filled with composite bovine bone. A single-blind randomized clinical trial

Abstract The purpose of this study was to evaluate the preservation of alveolar dimensions in human fresh extraction sockets filled with a composite bovine bone graft by means of design of single-blind randomized clinical trial. Forty participants had monoradicular teeth extracted (one teeth in each participant), and after were randomly divided into 2 groups: individuals whose fresh sockets were filled with the composite heterologous bone graft (Biomaterial Group), or with blood clot (Control Group). After extraction, the fresh sockets were measured at their greatest mesiodistal (MD) and bucco-lingual/palatal (BL/P) distance. Primary closure of the soft tissue was performed with a fibro-mucosal plug. After 120 post-operative days, the re-entry procedure was performed and the largest MD and BL/P measurements were again obtained to calculate the remodeling of the alveolar bone measured in percentage. In the biomaterial group, a percentage reduction of 1.62% and 3.29% in the MD and BL/P dimensions was observed 120 days after the extractions, whereas a reduction of 4.97% and 7.18% in the MD and BL/P dimensions occurred in the control group. There was a statistically significant difference (p<0.05) between the two groups for the bucco-palatal and mesiodistal measurements in the maxilla. In view of the results obtained, it can be concluded that composite bovine bone graft limited but did not impede alveolar bone remodeling.

Resumo O objetivo deste estudo foi avaliar em humanos a manutenção do volume em alvéolos frescos preenchidos por osso integral de origem bovina por meio de um estudo clínico randomizado com monocegamento. Quarenta dentes uni radiculares foram extraídos em 40 pacientes (um dente em cada participante), e apos estes pacientes foram divididos aleatoriamente em 2 grupos: indivíduos que tiveram o alvéolo fresco preenchido por osso integral de origem bovina (Grupo Biomaterial) ou por coagulo sanguíneo (Grupo Controle). Apos a exodontia os alvéolos foram medidos em suas maiores distancias mesio-distal (MD) e vestíbulo lingual/palatina (VL/P) por meio de compasso de ponta seca. O fechamento primário dos alvéolos foi realizado com um tampão fibromucoso. Apos 120 dias pós-operatórios durante o procedimento de reabertura foram obtidas novamente as maiores medidas MD e VL/P para calcular em porcentagem o nível de remodelação do osso alveolar. No grupo biomaterial observou-se uma redução em porcentagem de 1,62% e 3,29% nas medidas MD e VL/P 120 dias apos as extrações, enquanto no grupo controle houve uma redução de 4,97% e 7,18% nas medidas MD e VL/P no mesmo período. Houve diferença estatisticamente significante (p<0,05) entre os dois grupos para as medidas vestíbulo/palatina e mesiodistal na maxila. Diante dos resultados obtidos conclui-se que o osso integral de origem bovina limitou, mas não impediu a remodelação óssea alveolar.

Influence of different alcohol intake frequencies on alveolar bone loss in adult rats: A sem study.

BACKGROUND: Alcohol intake is associated with oral diseases and bone changes including alveolar bone loss in humans and in experimental animals. The main aim of the present study is to assess the effect of long-term alcohol intake, at different frequencies, on periodontal bone loss (PBL) in adult rats. MATERIAL AND METHODS: Thirty-six (36) rats were divided into 3 groups: Control (daily water intake, n=12), daily alcohol intake (20% ethanol, n=12), and social alcohol intake (20% ethanol twice a week, n=12). The rats were sacrificed after 90 days and their right maxillae were removed. Initially, a random portion from each group was analyzed through SEM (scanning electron microscope) to assess surface topography. Next, all pieces were dissected and stained with methylene blue 1% and photographed in stereomicroscope at 10x magnification. The PBL was assessed by measuring the distance between cement-enamel junction and alveolar bone crest. RESULTS: Results showed higher (p=0.0368) alcohol solution amount in the daily intake group than in the twice week intake one. The SEM showed qualitatively flat bone surface in the control group, the social intake group presented surface with few minor hollows, and the daily intake group evidenced increased number and diameter of wells. The comparison between groups showed higher bone loss (p<0.05) in both frequencies than in the control, but the bone loss was lower (p<0.05) in the social alcohol intake group than in the daily intake one. CONCLUSIONS: Alcohol intake may cause alveolar bone loss in periodontitis-free rats depending on the frequency. Key words:Alcohol intake, alveolar bone loss, alcohol-induced periodontitis, alcoholic rats.

Abordagem quanto ao diagnóstico e ao tratamento da avulsão dentária: uma revisão de literatura / Approach to diagnosis and treatment of dental avulsion: a literature review

Objetivo: descrever uma revisão da literatura que apresente as principais consequências que podem ocorrer quando o dente avulsionado é reimplantado de forma tardia, proporcionando um prognóstico desfavorável. Revisão de literatura: a avulsão dental é uma lesão traumática que se caracteriza pelo completo deslocamento do dente de seu alvéolo, acarretando danos tanto às estruturas de suporte do elemento dental quanto às estruturas pulpares. A permanência extraoral do elemento dental avulsionado por períodos longos ou em meios de armazenamento inadequados pode provocar danos adicionais. Considerações finais: as lesões de inserções são as principais consequências da pós-avulsão dentária, isso devido a uma ruptura do ligamento periodontal, com uma secagem excessiva antes do reimplante, danificando as células do ligamento periodontal, o que, por sua vez, provoca uma resposta inflamatória exacerbada em uma ampla área da superfície radicular. (AU)

Objective: to describe a literature review, which presents the main consequences of late reimplantation of the avulsed tooth, providing an unfavorable prognosis. Literature review: tooth avulsion is a traumatic lesion characterized by the complete displacement of the tooth from the socket, causing damage to the support structures of the dental element as well as to pulp structures. The long extraoral time of the avulsed tooth or the time in inadequate storage may cause additional trauma. Final considerations: insertion lesions are the main consequences of tooth post-avulsion due to a rupture in the periodontal ligament, with an excessive drying prior to reimplantation, which damages the periodontal ligament cells and causes an exacerbated inflammatory response in a large root surface area. (AU)

Etiología de las Pérdidas Dentales en Pacientes Rehabilitados con Prótesis sobre Implantes / Etiology of Tooth Loss in Patients Rehabilitated with Dental Implants

RESUMEN: El objetivo de esta investigación fue analizar la etiología de las pérdidas dentales en pacientes rehabilitados con prótesis sobre implantes. Se realizó un estudio transversal con informaciones de 93 pacientes de una clínica privada que recibieron tratamiento con implantes en el período de 2000 a 2009. Los datos fueron recolectados a través de las fichas clínicas, documentaciones radiográficas y fotografías de los casos clínicos. Se levantaron datos sobre género, edad, nivel de escolaridad, hábito de fumar, tipo de diente extraído y razón de la extracción. Los resultados mostraron que la razón periodontal fue el principal motivo de las pérdidas dentales, representando el 24,7 %, seguida por las fracturas radiculares con pines metálicos (23,7 %) y caries secundarias (15,1 %). En los pacientes menores de 40 años, los traumatismos dentales y las fracturas radiculares con pino fueron responsables de la mayoría de las pérdidas. Las razones de las pérdidas dentales mostraron significancia estadística con la variable edad (p<0,05). El género, el hábito de fumar y el grado de escolaridad no mostraron asociación significativa (p>0,05) con las razones de las pérdidas dentales.

ABSTRACT: The aim of this study was to analyze the etiology of tooth loss in patients rehabilitated with dental implants. Was conducted a cross-sectional study with data from 93 patients from a private clinic who were treated with implants from the year 2000 until 2009. Data were collected through medical records, radiographic documentation and photographs of clinical cases. Data on sex, age, education level, smoking habits, teeth loss localization and extraction ratio were analyzed. The results showed that periodontal disease was the main reason for tooth loss, accounting for 24.7 %, followed by root fractures with posts (23.7 %) and secondary caries (15.1 %). In patients below 40 years, dental trauma and root fractures were responsible for most of the losses. The reasons for tooth loss showed statistical significance with the age (p<0.05). Sex, smoking habits and education showed no significant association (p>0.05) with the reasons of the tooth loss.

Biomechanical effect of inclined implants in fixed prosthesis: strain and stress analysis / Efeito biomecânico de implantes inclinados em prótese fixa: analise das tensões e deformações

Introduction: Implant inclinations can be corrected using mini abutments at different angulations. Objective: To analyze the influence of external hexagon implants in different inclinations (3 levels) on the microstrain distribution generated around three implants. Method: A geometric bone model was created through Rhinoceros CAD software (version 5.0 SR8, Mcneel North America, Seattle, WA, USA). Three implants (4.1 × 13 mm) were modeled and inserted inside the substrate at three different inclinations: 0º, 17º and 30º. Next, all groups received mini conical abutments, fixation screws and a simplified prosthesis. The final geometry was exported in STEP format to analysis software and all materials were considered homogeneous, isotropic and linearly elastic. An axial load (300N) was applied on the center of the prosthesis. An in vitro study was conducted with same conditions and groups for validating the tridimentional model. Result: Stress was concentrated on the external area of the implants, in contact with the cortical bone and external hexagon. For the bone simulator, the strain increased in the peri-implant region according to the increase in the implant's inclination. The difference between groups was significant (p = 0.000). The 30º group presented higher stress and strain concentration. Conclusion: The microstrain and stress increase around implants directly proportional to the increase of the installation angle.

Introdução: A inclinação dos implantes pode ser corrigida através de mini-pilares de diferentes angulações. Objetivo: Analisar a influência de implantes com hexágono externo em diferentes inclinações (3 níveis) na distribuição de microdeformações geradas em torno de três implantes. Método: Um modelo geométrico de osso foi criado através do software CAD Rhinoceros (versão 5.0 SR8, Mcneel North America, Seattle, WA, EUA). Três implantes (4,1 × 13 mm) foram modelados e inseridos no interior do substrato em três diferentes inclinações: 0º, 17º e 30º. Em seguida, todos os grupos receberam mini-pilares cônicos, parafusos de fixação e prótese simplificada. A geometria final foi exportada em formato STEP para software de análise e todos os materiais foram considerados homogêneos, isotrópicos e linearmente elásticos. Uma carga axial (300N) foi aplicada no centro da prótese. Um estudo in vitro foi conduzido com as mesmas condições e grupos para validar o modelo tridimensional. Resultado: A concentração de tensão ocorreu na área externa dos implantes, em contato com o osso cortical e o hexágono externo. Para o simulador ósseo, a deformação aumentou na região peri-implantar de acordo com o aumento da inclinação do implante. A diferença entre os grupos foi significativa (p = 0.000). O grupo de 30º apresentou maior concentração de tensão e deformação. Conclusão: O aumento da microdeformação e das tensões ao redor dos implantes aumenta diretamente proporcional ao aumento do ângulo de instalação.

Influence of different restorative materials on the stress distribution in dental implants.

BACKGROUND: To assist clinicians in deciding the most suitable restorative materials to be used in the crowns and abutment in implant rehabilitation. MATERIAL AND METHODS: For finite element analysis (FEA), a regular morse taper implant was created using a computer aided design software. The implant was inserted at the bone model with 3 mm of exposed threads. An anatomic prosthesis representing a first maxillary molar was modeled and cemented on the solid abutment. Considering the crown material (zirconia, chromium-cobalt, lithium disilicate and hybrid ceramic) and abutment (Titanium and zirconia), the geometries were multiplied, totaling eight groups. In order to perform the static analysis, the contacts were considered bonded and each material was assigned as isotropic. An axial load (200 N) was applied on the crown and fixation occurred on the base of the bone. Results using Von-Mises criteria and micro strain values were obtained. A sample identical to the CAD model was made for the Strain Gauge (SG) analysis; four SGs were bonded around the implant to obtain micro strain results in bone tissue. RESULTS: FEA results were 3.83% lower than SG. According to the crown material, it is possible to note that the increase of elastic modulus reduces the stress concentration in all system without difference for bone. CONCLUSIONS: Crown materials with high elastic modulus are able to decrease the stress values in the abutments while concentrates the stress in its structure. Zirconia abutments tend to concentrate more stress throughout the prosthetic system and may be more susceptible to mechanical problems than titanium. Key words:Finite element analysis, dental implants, ceramic.

The importance of correct implants positioning and masticatory load direction on a fixed prosthesis.

BACKGROUND: Through the biomechanical study of dental implants, it is possible to understand the dissipation effects of masticatory loads in different situations and prevent the longevity of osseointegration. Aims: To evaluate the microstrains generated around external hexagon implants, using axial and non-axial loads in a fixed four-element prosthesis with straight implants and implants inclined at 17°. MATERIAL AND METHODS: Three implants were modeled using CAD software following the manufacturer's measurements. Then, implants were duplicated and divided into two groups: one with straight implants and respective abutments, and the other with angled implants at 17° and respective abutments. Both groups were arranged inside a block simulating bone tissue. A simplified fixed prosthesis was installed on both groups and the geometries were exported to CAE software. Five loads of 300N were performed at axial and non-axial points on the fixed prosthesis. Stress on the implants and strain on the block were both analyzed. An in vitro experiment was performed following all structures made in FEA in order to validate the model. In each experimental block, 4 strain gauges were linearly placed between the implants and the same loads were repeated with a loading applicator device. RESULTS: The deformations computed by the gauges were correlated with the FEA results, showing that the group with inclined implants had more damaging biomechanical behavior and was significantly different from the group with straight implants (P<0.005). CONCLUSIONS: The mathematical model used is valid and inclined implants can induce unwanted bone remodeling. Key words:Finite Element Analysis, Dental Implants, Fixed Prosthesis.

Strain Gauge Evaluation of Transfer Impression Techniques of Multiple Implant-Supported Prosthesis.

PURPOSE: This in vitro study assessed the accuracy of multiple implant-level impression techniques (open tray and closed tray) for the fabrication of 3-unit implant prostheses with strain gauge (SG) analysis. MATERIALS AND METHODS: A polyurethane master model was designed to simulate a clinical situation. Two rigid custom trays were fabricated for the model. The impression material used was polysulfide. Transfer implant impressions were made using 2 techniques; ten tapered copings not splinted (custom closed tray) and ten square copings splinted with acrylic-resin (custom open tray). The improved stone models were allowed to set for 1 hour before being separated from the impression. The superstructures were sprued, invested, and cast with a cobalt-chromium alloy. Four SGs were bonded on the surface of each polyurethane block. RESULTS: A statistically significant difference was found between the 2 impression techniques tested (P = 0.000). This study found a significant average difference of 144.68 ± 5.53 µÎµ for open custom tray and 253.3 ± 16.7 µÎµ for closed custom tray. CONCLUSION: The custom open tray technique was the most accurate impression for multiple implants compared with closed custom tray.

Validation of a Simplified Implant-Retained Cantilever Fixed Prosthesis.

PURPOSE: To evaluate the stress and strain generated in a fixed four-element prosthesis under the application of axial and nonaxial loads using a simplified implant-supported fixed prosthesis model. MATERIALS AND METHODS: A 3-dimensional model was constructed containing 3 implants with a conventional anatomical prosthesis (G1). The second model with the same implant system received the simplified prosthesis (G2). A load of 300 N was applied at an axial point and a nonaxial point through finite element analysis software. RESULTS: The G2 group showed different values of stress concentration in the prosthesis, fixation screw, retention screw, and abutments when compared with G1. Within a limit of 10% degrees of acceptability, the stress on the implants and the bone strain were enclosed for both models of prostheses. CONCLUSION: The simplified fixed prosthesis evaluated presents biomechanical behavior similar to an anatomical prosthesis in the implants and in the surrounding bone structure.

Estética dental associada ao tratamento da pigmentação melânica gengival / Dental aesthetics associated with treatment of melanin pigmentation

Pacientes estão cada vez mais conscientes da estética branca (dentes) e vermelha (gengiva). Neste caso clínico, a paciente apresentava a forma e cor dos elementos dentários alterada, assim como uma gengiva escurecida. A pigmentação da melanina é normal e fisiológica, podendo ser suavizada com técnicas cirúrgicas periodontais. O objetivo deste trabalho foi tratar a questão da pigmentação da melanina e promover uma anatomia dentária satisfatória que abrangesse a estética e a funcionalidade do conjunto mastigatório.

Patients are more conscious about white (teeth) and red (gengiva) esthetics. In this clinical procedure, the patient presented tooth shape and color modifications, and dark gengiva as well. Melanin pigmentation is a physiologic condition which can be alleviated by periodontal surgical techniques. The aim of this paper was to highlight this issue and to promote a satisfactory tooth anatomy regarding esthetics and function for the masticatory system.