Quantitative determination of 58 aromatic amines and positional isomers in textiles by high-performance liquid chromatography with electrospray ionization tandem mass spectrometry.

A straightforward method for simultaneous determination of 58 aromatic amines (AAs) in clothing textiles is described. Of the tested amines, 22 are known carcinogens and regulated under European law. Further unregulated amines, which are suspected to be carcinogenic or mutagenic, are also expected to occur in textiles. The focus of this study was to obtain a multimethod with regulated and unregulated AAs and to separate different positional isomers of specific amines. To achieve this goal, the HPLC parameters such as column phase chemistry and mobile phase pH were optimized. All other amines were separated with the same conditions evaluated for the positional isomers. The sample preparation was reduced to a minimum in accordance to DIN EN 14362-1. After reductive cleavage and dilution of the extracts, the samples were prepared for LC-MS/MS analysis. Further cleanup of the samples with diatomaceous earth was no longer required with this modified sample preparation. The method was validated by spiking the extracts of blank textiles with the chosen amines. Lower Limits of Quantification (LLOQs) ranged from 1 to 10 mg kg-1. Excellent linearity from 10 to 500 µg L-1 was obtained with coefficients (r) higher than 0.99 allowing a one-point calibration (300 µg L-1 corresponding to 60 mg kg-1 in textiles) forced through zero for the samples. Recovery ranged from 88 to 116% with intra- and inter-day precision values of 1.8-12.1%. The accuracy of this method was tested by a certified reference material (iis18A03, Institute for laboratory Studies, the Netherlands) and showed excellent recoveries higher than 95%. Finally, the described method was successfully applied on 150 real samples with different textile fibres and colours. Positive results were confirmed by means of the spectral library and with the ion ratios.

Study of the in vitro and in vivo metabolism of 4-HO-MET.

4-Hydroxy-N-methyl-N-ethyltryptamine (4-HO-MET) is a new psychoactive substance (NPS) of the chemical class of tryptamines. It shows structural similarities to the endogenous neurotransmitter serotonin, and is a serotonergic hallucinogen, affecting emotional, motoric, and cognitive functions. The knowledge about its biotransformation is mandatory to confirm the abuse of the substance by urine analysis in forensic cases. Therefore, phase I metabolites were generated by the use of the pooled human liver microsomes (pHLM) in vitro model and analyzed by high-performance liquid chromatography high-resolution tandem mass spectrometry with information-dependent acquisition (HPLC-IDA-HR-MS/MS). Furthermore, three authentic urine samples was analyzed and results were compared: 12 different in vitro and 4 in vivo metabolites were found. The predominant biotransformation steps observed in vitro were mono- or dihydroxylation of 4-HO-MET, besides demethylation, demethylation in combination with monohydroxylation, formation of a carboxylic acid, deethylation, and oxidative deamination. In vivo, monohydroxylation, and glucuronidation were detected. A metabolic pathway based on these results was proposed. For the analysis of urine samples in forensic cases, the N-oxide metabolite and the HO-alkyl metabolite are recommended as target compounds, besides the glucuronides of 4-HO-MET and the parent compound 4-HO-MET itself.

Decrease of ethyl glucuronide concentrations in hair after exposure to chlorinated swimming pool water.

The direct alcohol marker ethyl glucuronide (EtG) is widely used for the assessment of alcohol consumption behavior and abstinence monitoring by hair analysis. We investigated the influence of chlorinated swimming pool water on EtG concentrations in hair in comparison to deionized water (Milli-Q) containing no chlorine. EtG concentrations were measured with a validated online solid-phase extraction-liquid chromatography-tandem mass spectrometry (SPE-LC-MS/MS) method. EtG positive hair samples were obtained from 3 regular drinkers and incubated for 0, 2, 4, 6, 8, and 10 hours at room temperature. EtG concentrations in hair were reduced after 2 hours of incubation in chlorinated water by 20 ± 12% (range: 4-33%), in deionized water by 24 ± 5% (range: 18-29%). Incubation for 10 hours resulted in a decrease in EtG concentrations of 57 ± 6% (range: 52-65%) for chlorinated water and 47 ± 11% (range: 32-60%) for deionized water. To demonstrate washout in forensic hair samples, 20 samples from subjects with known alcohol consumption behavior were investigated additionally. The samples were divided into 2 strands and analyzed with incubation in chlorinated water for 10 hours and for comparison without any incubation. A mean decrease of 53 ± 18% (range: 26-88%) was observed. These results clearly demonstrate that washout effects are caused by water and have a significant impact on EtG concentrations in hair. For people with hair that are regularly exposed to water for a longer period (eg. swimmers), washout effects may lead to a significant decrease of EtG concentrations in hair. Concentrations may fall below threshold concentrations used for the interpretation of consumption habits (7 pg/mg for social consumption, 30 pg/mg for excessive consumption).

Determination of Δ9-tetrahydrocannabinolic acid A (Δ9-THCA-A) in whole blood and plasma by LC-MS/MS and application in authentic samples from drivers suspected of driving under the influence of cannabis.

Delta-9-tetrahydrocannabinolic acid A (THCA-A) is the biosynthetic precursor of delta-9-tetrahydrocannabinol (THC) in cannabis plants, and has no psychotropic effects. THCA-A can be detected in blood and urine, and several metabolites have been identified. THCA-A was also shown to be incorporated in hair by side stream smoke to a minor extent, but incorporation via blood stream or sweat seems unlikely. The detection of THCA-A in biological fluids may serve as a marker for differentiating between the intake of prescribed THC medication - containing only pure THC - and cannabis products containing THC besides THC-acid A and other cannabinoids. However, the knowledge about its usefulness in forensic cases is very limited. The aim of the present work was the development of a reliable method for THCA-A determination in human blood or plasma using LC-MS/MS and application to cases of driving under the influence of drugs. Fifty eight (58) authentic whole blood and the respective plasma samples were collected from drivers suspected of driving under the influence of cannabis from the region of Bern (Switzerland). Samples were first tested for THC, 11-OH-THC and THC-COOH, and then additionally for THCA-A. For this purpose, the existing LC-MS/MS method was modified and validated, and found to be selective and linear over a range of 1.0 to 200ng/mL (the correlation coefficients were above 0.9980 in all validation runs). Limit of detection (LOD) and limit of quantification (LOQ) were 0.3ng/mL and 1.0ng/mL respectively. Intra- and inter-assay accuracy were equal or better than 90% and intra- and inter-assay precision were equal or better than 11.1%. The mean extraction efficiencies were satisfactory being equal or higher than 85.4%. THCA-A was stable in whole blood samples after 3 freeze/thaw cycles and storage at 4°C for 7 days. Re-injection (autosampler) stability was also satisfactory. THC was present in all blood samples with levels ranging from 0.7 to 51ng/mL. THCA-A concentrations ranged from 1.0 to 496ng/mL in blood samples and from 1.4 to 824ng/mL in plasma samples. The plasma:blood partition coefficient had a mean value of 1.7 (±0.21, SD). No correlation was found between the degree of intoxication or impairment stated in the police protocols or reports of medical examinations and the detected THCA-A-concentration in blood.

Determination of the external contamination and cross-contamination by cytotoxic drugs on the surfaces of vials available on the Swiss market.

INTRODUCTION: The external contamination and cross-contamination by cytotoxic drugs on the surface (outside and septum) of 133 vials from various manufacturers and available on the Swiss market were evaluated. All of the tested vials contained one of the following active ingredients: cyclophosphamide, cytarabine, doxorubicin, epirubicin, etoposide phosphate, gemcitabine, ifosfamide, irinotecan, methotrexate or vincristine. METHODS AND MATERIALS: The validated wiping liquid chromatography-mass spectrometry method used in this study allowed for the simultaneous determination of these 10 cytotoxic drugs in less than 30 min. RESULTS: External contamination by cytotoxic drugs was detected on 63% of tested vials (outside and septum). The highest contamination level was observed on etoposide phosphate vials with 1896.66 ng of active ingredient on the outside of the vial. Approximately 20% of the contaminated vials had greater than 10 ng of cytotoxic drugs. Chemical contamination on the septum was detected on 38% of the vials. No contamination or very low levels of cytotoxic drugs, less than 1 ng per vial, were detected on the vials protected by plastic shrink-wrap. Traces of cytotoxic drugs different from the active ingredient were detected on 35% of the tested vials. CONCLUSION: Handling cytotoxic vials with gloves and having a procedure for the decontamination of vials are of the utmost importance for reducing exposure to cytotoxic drugs. Moreover, manufacturers must improve their procedures to provide products free from any contamination.

Evaluation of decontamination efficacy of cleaning solutions on stainless steel and glass surfaces contaminated by 10 antineoplastic agents.

OBJECTIVES: The handling of antineoplastic agents results in chronic surface contamination that must be minimized and eliminated. This study was designed to assess the potential of several chemical solutions to decontaminate two types of work surfaces that were intentionally contaminated with antineoplastic drugs. METHODS: A range of solutions with variable physicochemical properties such as their hydrophilic/hydrophobic balance, oxidizing power, desorption, and solubilization were tested: ultrapure water, isopropyl alcohol, acetone, sodium hypochlorite, and surfactants such as dishwashing liquid (DWL), sodium dodecyl sulfate (SDS), Tween 40, and Span 80. These solutions were tested on 10 antineoplastic drugs: cytarabine, gemcitabine, methotrexate, etoposide phosphate, irinotecan, cyclophosphamide, ifosfamide, doxorubicin, epirubicin, and vincristine. To simulate contaminated surfaces, these molecules (200ng) were deliberately spread onto two types of work surfaces: stainless steel and glass. Recovered by wiping with a specific aqueous solvent (acetonitrile/HCOOH; 20/0.1%) and an absorbent wipe (Whatman 903®), the residual contamination was quantified using high-performance liquid chromatography (HPLC) coupled to mass spectrometry. To compare all tested cleaning solutions, a performance value of effectiveness was determined from contamination residues of the 10 drugs. RESULTS: Sodium hypochlorite showed the highest overall effectiveness with 98% contamination removed. Ultrapure water, isopropyl alcohol/water, and acetone were less effective with effectiveness values of 76.8, 80.7, and 40.4%, respectively. Ultrapure water was effective on most hydrophilic molecules (97.1% for cytarabine), while on the other hand, isopropyl alcohol/water (70/30, vol/vol) was effective on the least hydrophilic ones (85.2% for doxorubicin and 87.8% for epirubicin). Acetone had little effect, whatever the type of molecule. Among products containing surfactants, DWL was found effective (91.5%), but its formulation was unknown. Formulations with single surfactant non-ionics (tween 40 and span 80) or anionic (SDS) were also tested. Finally, solutions containing 10(-2) M anionic surfactants and 20% isopropyl alcohol had the highest global effectiveness at around 90%. More precisely, their efficacy was the highest (94.8%) for the most hydrophilic compounds such as cytarabine and around 80.0% for anthracyclines. Finally, the addition of isopropyl alcohol to surfactant solutions enhanced their decontamination efficiency on the least hydrophilic molecules. Measured values from the stainless steel surface were similar to those from the glass one. CONCLUSION: This study demonstrates that all decontamination agents reduce antineoplastic contamination on work surfaces, but none removes it totally. Although very effective, sodium hypochlorite cannot be used routinely on stainless steel surfaces. Solutions containing anionic surfactant such as SDS, with a high efficiency/safety ratio, proved most promising in terms of surface decontamination.

Wipe sampling procedure coupled to LC-MS/MS analysis for the simultaneous determination of 10 cytotoxic drugs on different surfaces.

A simple wipe sampling procedure was developed for the surface contamination determination of ten cytotoxic drugs: cytarabine, gemcitabine, methotrexate, etoposide phosphate, cyclophosphamide, ifosfamide, irinotecan, doxorubicin, epirubicin and vincristine. Wiping was performed using Whatman filter paper on different surfaces such as stainless steel, polypropylene, polystyrol, glass, latex gloves, computer mouse and coated paperboard. Wiping and desorption procedures were investigated: The same solution containing 20% acetonitrile and 0.1% formic acid in water gave the best results. After ultrasonic desorption and then centrifugation, samples were analysed by a validated liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS) in selected reaction monitoring mode. The whole analytical strategy from wipe sampling to LC-MS/MS analysis was evaluated to determine quantitative performance. The lowest limit of quantification of 10 ng per wiping sample (i.e. 0.1 ng cm(-2)) was determined for the ten investigated cytotoxic drugs. Relative standard deviation for intermediate precision was always inferior to 20%. As recovery was dependent on the tested surface for each drug, a correction factor was determined and applied for real samples. The method was then successfully applied at the cytotoxic production unit of the Geneva University Hospitals pharmacy.

Analysis of anticancer drugs: a review.

In the last decades, the number of patients receiving chemotherapy has considerably increased. Given the toxicity of cytotoxic agents to humans (not only for patients but also for healthcare professionals), the development of reliable analytical methods to analyse these compounds became necessary. From the discovery of new substances to patient administration, all pharmaceutical fields are concerned with the analysis of cytotoxic drugs. In this review, the use of methods to analyse cytotoxic agents in various matrices, such as pharmaceutical formulations and biological and environmental samples, is discussed. Thus, an overview of reported analytical methods for the determination of the most commonly used anticancer drugs is given.

Quality control of pharmaceutical formulations containing cisplatin, carboplatin, and oxaliplatin by micellar and microemulsion electrokinetic chromatography (MEKC, MEEKC).

A micellar electrokinetic chromatography (MEKC) method was developed for the determination of cisplatin, carboplatin, and oxaliplatin in pharmaceutical formulations. The background electrolyte consisted of a phosphate buffer (pH 7.0; 25 mM) with sodium dodecyl sulfate (80 mM). The applied voltage was 30 kV and the sample injection was performed in the hydrodynamic mode. All analyses were carried out in a fused silica capillary with an internal diameter of 50 µm and a total length of 64.5 cm. The detection of target compounds was performed at 200 nm. Under these conditions, a complete separation of cisplatin, carboplatin and oxaliplatin was achieved in less than 10 min. The MEKC-UV method was validated and trueness values between 99.7% and 100.8% were obtained with repeatability and intermediate precision values of 0.7-1.4% and 1.1-1.7%, respectively for the three drugs. This method was found appropriate for controlling pharmaceutical formulations containing platinum complexes and successfully applied in quality control at the Geneva University Hospitals.

Simultaneous quantification of ten cytotoxic drugs by a validated LC-ESI-MS/MS method.

A liquid chromatography separation with electrospray ionisation and tandem mass spectrometry detection method was developed for the simultaneous quantification of ten commonly handled cytotoxic drugs in a hospital pharmacy. These cytotoxic drugs are cytarabine, gemcitabine, methotrexate, etoposide phosphate, cyclophosphamide, ifosfamide, irinotecan, doxorubicin, epirubicin and vincristine. The chromatographic separation was carried out by RPLC in less than 21 min, applying a gradient elution of water and acetonitrile in the presence of 0.1% formic acid. MS/MS was performed on a triple quadrupole in selected reaction monitoring mode. The analytical method was validated to determine the limit of quantification (LOQ) and quantitative performance: lowest LOQs were between 0.25 and 2 ng mL(-1) for the ten investigated cytotoxic drugs; trueness values (i.e. recovery) were between 85% and 110%, and relative standard deviations for both repeatability and intermediate precision were always inferior to 15%. The multi-compound method was successfully applied for the quality control of pharmaceutical formulations and for analyses of spiked samples on potentially contaminated surfaces.

Determination of potassium, sodium, calcium and magnesium in total parenteral nutrition formulations by capillary electrophoresis with contactless conductivity detection.

A simple method based on capillary electrophoresis with a capacitively coupled contactless conductivity detector (CE-C(4)D) was developed for the determination of potassium, sodium, calcium and magnesium in parenteral nutrition formulations. A hydro-organic mixture, consisting of 100 mM Tris-acetate buffer at pH 4.5 and acetonitrile (80:20, v/v), was selected as the background electrolyte. The applied voltage was 30 kV, and sample injection was performed in hydrodynamic mode. All analyses were carried out in a fused silica capillary with an internal diameter of 50 microm and a total length of 64.5 cm. Under these conditions, complete separation between all cations was achieved in less than 4 min. The CE-C(4)D method was validated, and trueness values between 98.6% and 101.8% were obtained with repeatability and intermediate precision values of 0.4-1.3% and 0.8-1.8%, respectively. Therefore, this method was found to be appropriate for controlling potassium, sodium, calcium and magnesium in parenteral nutrition formulations and successfully applied in daily quality control at the Geneva University Hospitals.

Determination of suxamethonium in a pharmaceutical formulation by capillary electrophoresis with contactless conductivity detection (CE-C(4)D).

A simple method based on capillary electrophoresis with a capacitively coupled contactless conductivity detector (CE-C(4)D) was developed for the determination of suxamethonium (SUX) in a pharmaceutical formulation. A hydro-organic mixture, consisting of 100mM Tris-acetate buffer at pH 4.2 and acetonitrile (90:10, v/v), was selected as background electrolyte (BGE). The applied voltage was 30kV, and the sample injection was performed in the hydrodynamic mode. All analyses were carried out in a fused silica capillary with an internal diameter of 50 microm and a total length of 64.5cm. Under these conditions, a complete separation between SUX, sodium ions and the main degradation products (choline) was achieved in less than 4min. The presence of acetonitrile in the BGE allowed a reduction of SUX adsorption on the capillary wall. The CE-C(4)D method was validated, and trueness values between 98.8% and 101.1% were obtained with repeatability and intermediate precision values of 0.7-1.3% and 1.2-1.6%, respectively. Therefore, this method was found appropriate for controlling pharmaceutical formulations containing suxamethonium and degradation products.