Conventional sintering of nano-crystalline Yttria-Stabilized Zirconia enables high-strength, highly translucent and opalescent dental ceramics.

Development of restorative materials capable of mimicking optical and mechanical performance of natural teeth is a quest in aesthetic density. Yttria-Stabilized Zirconia (YSZ) ceramics represent one of the most popular choices for dental restorations, owing to their biocompatibility, white colour, and the possibility to use CAD-CAM technologies. In particular, YSZ doped with 3 mol. % yttria (3YSZ) is popular because it presents high strength. Nonetheless, the limited light transmission of commercially available high strength 3YSZ does not meet the requirements of highly aesthetic cases. On the other side, YSZ presenting a larger portion of yttria are more translucent but exhibit modest strength. Here, we report on fabrication of dense zirconia nanostructures in bulk form via conventional pressure-less sintering at temperatures down to 1100-1200 °C, achieving highly translucent and strong 3YSZ with significant opalescent behaviour. Both Hall-Petch and inverse Hall-Petch relationship were observed in 3YSZ samples with average grain size in the range of 250 nm and 55 nm, demonstrating the importance of grain size control to enhance both optical and mechanical properties of zirconia ceramics, simultaneously. Maximum biaxial strength of 1980 ± 260 MPa, in-line light transmission of 38% in the visible spectrum and opalescence approaching that of enamel were obtained at optimum grain size of 80 ± 5 nm. The notable optical properties are linked to the miniaturization of the residual pores and refinement of grain size towards the nanoscale while the superior mechanical strength is justified by the activation of different energy dissipation processes at nano and macroscale.

Fly-Ash Evaluation as Potential EOL Material Replacement of Cement in Pastes: Morpho-Structural and Physico-Chemical Properties Assessment.

The main objective of the study was to produce alternative binder materials, obtained with low cost, low energy consumption, and low CO2 production, by regenerating end-of-life (EOL) materials from mineral deposits, to replace ordinary Portland cement (OPC). The materials analyzed were ash and slag from the Turceni thermal power plant deposit, Romania. These were initially examined for morphology, mineralogical composition, elemental composition, degree of crystallinity, and heating behavior, to determine their ability to be used as a potential source of supplementary cementitious materials (SCM) and to establish the activation and transformation temperature in the SCM. The in-situ pozzolanic behavior of commercial cement, as well as cement mixtures with different percentages of ash addition, were further observed. The mechanical resistance, water absorption, sorptivity capacity, resistance to alkali reactions (ASR), corrosion resistance, and resistance to reaction with sulfates were evaluated in this study using low-vacuum scanning electron microscopy.

Cadmium-Free and Efficient Type-II InP/ZnO/ZnS Quantum Dots and Their Application for LEDs.

It is a generally accepted perspective that type-II nanocrystal quantum dots (QDs) have low quantum yield due to the separation of the electron and hole wavefunctions. Recently, high quantum yield levels were reported for cadmium-based type-II QDs. Hence, the quest for finding non-toxic and efficient type-II QDs is continuing. Herein, we demonstrate environmentally benign type-II InP/ZnO/ZnS core/shell/shell QDs that reach a high quantum yield of ∼91%. For this, ZnO layer was grown on core InP QDs by thermal decomposition, which was followed by a ZnS layer via successive ionic layer adsorption. The small-angle X-ray scattering shows that spherical InP core and InP/ZnO core/shell QDs turn into elliptical particles with the growth of the ZnS shell. To conserve the quantum efficiency of QDs in device architectures, InP/ZnO/ZnS QDs were integrated in the liquid state on blue light-emitting diodes (LEDs) as down-converters that led to an external quantum efficiency of 9.4% and a power conversion efficiency of 6.8%, respectively, which is the most efficient QD-LED using type-II QDs. This study pointed out that cadmium-free type-II QDs can reach high efficiency levels, which can stimulate novel forms of devices and nanomaterials for bioimaging, display, and lighting.

Quantum dot and electron acceptor nano-heterojunction for photo-induced capacitive charge-transfer.

Capacitive charge transfer at the electrode/electrolyte interface is a biocompatible mechanism for the stimulation of neurons. Although quantum dots showed their potential for photostimulation device architectures, dominant photoelectrochemical charge transfer combined with heavy-metal content in such architectures hinders their safe use. In this study, we demonstrate heavy-metal-free quantum dot-based nano-heterojunction devices that generate capacitive photoresponse. For that, we formed a novel form of nano-heterojunctions using type-II InP/ZnO/ZnS core/shell/shell quantum dot as the donor and a fullerene derivative of PCBM as the electron acceptor. The reduced electron-hole wavefunction overlap of 0.52 due to type-II band alignment of the quantum dot and the passivation of the trap states indicated by the high photoluminescence quantum yield of 70% led to the domination of photoinduced capacitive charge transfer at an optimum donor-acceptor ratio. This study paves the way toward safe and efficient nanoengineered quantum dot-based next-generation photostimulation devices.

End-of-Life Materials Used as Supplementary Cementitious Materials in the Concrete Industry.

A sustainable solution for the global construction industry can be partial substitution of Ordinary Portland Cement (OPC) by use of supplementary cementitious materials (SCMs) sourced from industrial end-of-life (EOL) products that contain calcareous, siliceous and aluminous materials. Candidate EOL materials include fly ash (FA), silica fume (SF), natural pozzolanic materials like sugarcane bagasse ash (SBA), palm oil fuel ash (POFA), rice husk ash (RHA), mine tailings, marble dust, construction and demolition debris (CDD). Studies have revealed these materials to be cementitious and/or pozzolanic in nature. Their use as SCMs would decrease the amount of cement used in the production of concrete, decreasing carbon emissions associated with cement production. In addition to cement substitution, EOL products as SCMs have also served as coarse and also fine aggregates in the production of eco-friendly concretes.

Cross-linked enzyme lyophilisates (CLELs) of urease: A new method to immobilize ureases.

In this study, we presented a new approach for immobilizing JBU (Jack bean urease), by producing urease cross-linked enzyme lyophilisates (CLELs). Through the use of bovine serum albumin (BSA), lyophilisation, cross-linking with dextran polyaldehyde (DPA), and optimizing cross-linker pH, the urease-CLELs produced show an increase in relative catalytic activity that is 1.47 times higher than that of free urease, while remaining stable up to temperatures of 85 °C. Urease-CLEL activity increases in direct proportion with the increasing BSA content due to the offered additional lysine (Lys) groups which are potential cross-linking points providing better immobilization and retention of JBU, while lyophilisation also enables stabilization by eliminating solvating water molecules and intra-molecular reactions that may block the cross-linking residues. Two most commonly used cross-linkers that are reacting with the available Lys groups, i.e.glutaraldehyde (GA) and bulkier alternative DPA, have been selected for the immobilization of urease. The catalytic activity increase with DPA suggests an improved access to the active site through hindering blockage, while the increase with alkaline pH of the cross-linkers indicates decreased buffer inhibition. The long lifetime (113% residual activity after 4 weeks), recyclability (132% residual activity after 10 cycles) and thermal stability (276% relative activity at 85 °C) of these urease-CLELs demonstrate that they are technologically attractive as green biocatalysts, while our immobilization approach offers an alternative to conventional methods for proteins that are difficult to immobilise.

Formation of Nanocomposite Solid Oxide Fuel Cell Cathodes by Preferential Clustering of Cations from a Single Polymeric Precursor.

Conventional composite cathodes used in solid oxide fuel cells (SOFCs) are fabricated by co-sintering of electrocatalyst and ionic conductor powders at 1100-1250 °C. The relatively high-temperature heat treatments required to ensure bonding among the powders and between the powders and electrolyte results in the formation of resistive phases and coarse microstructures corresponding to short triple-phase boundary (TPB) length and, consequently, low oxygen reduction activity. In the present work, to achieve long TPBs and avoid resistive phase formation, we propose to fabricate nanocomposite La0.8Sr0.2MnO3-Ce0.8Sm0.2O2 (LSM-SDC) and La0.8Ca0.2MnO3-Ce0.8Sm0.2O2 (LCM-SDC) thin film cathodes by a low-temperature method, which involves the use of a single polymeric precursor solution containing all the respective cations. Owing to the molecular level mixing and the liquid lack of any powder-based starting material, we envision that preferential clustering of cations forming nanoscale electrocatalyst and ionic conductor particles will take place upon heat treatment at relatively low temperatures of 600-800 °C. Here, we report for the first time in the literature, a correlation between the heat-treatment temperature-phase evolution-cluster formation-surface chemistry evolution and electrochemical activity of nanocomposite thin film cathodes fabricated from a single polymeric precursor. Our experiments reveal that highest electrochemical activity is achieved when the electrocatalyst phase is poorly crystallized, complete clustering of cations takes place, and A-site dopant segregation at the surface is minimal.

Aptamer and nanomaterial based FRET biosensors: a review on recent advances (2014-2019).

Fluorescence resonance energy transfer, one of the most powerful phenomena for elucidating molecular interactions, has been extensively utilized as a biosensing tool to provide accurate information at the nanoscale. Numerous aptamer- and nanomaterial-based FRET bioassays has been developed for detection of a large variety of molecules. Affinity probes are widely used in biosensors, in which aptamers have emerged as advantageous biorecognition elements, due to their chemical and structural stability. Similarly, optically active nanomaterials offer significant advantages over conventional organic dyes, such as superior photophysical properties, large surface-to-volume ratios, photostability, and longer shelf life. In this report (with 175 references), the use of aptamer-modified nanomaterials as FRET couples is reviewed: quantum dots, upconverting nanoparticles, graphene, reduced graphene oxide, gold nanoparticles, molybdenum disulfide, graphene quantum dots, carbon dots, and metal-organic frameworks. Tabulated summaries provide the reader with useful information on the current state of research in the field. Graphical abstract Schematic representation of a fluorescence resonance energy transfer-based aptamer nanoprobe in the absence and presence of a given target molecule (analyte). Structures are not drawn to their original scales.

Efficient White LEDs Using Liquid-state Magic-sized CdSe Quantum Dots.

Magic clusters have attracted significant interest to explore the dynamics of quantum dot (QD) nucleation and growth. At the same time, CdSe magic-sized QDs reveal broadband emission in the visible wavelength region, which advantageously offer simple integration of a single-type of nanomaterial and high color rendering ability for white light-emitting diodes (LEDs). Here, we optimized the quantum yield of magic-sized CdSe QDs up to 22% via controlling the synthesis parameters without any shelling or post-treatment process and integrated them in liquid-state on blue LED to prevent the efficiency drop due to host-material effect. The fabricated white LEDs showed color-rendering index and luminous efficiency up to 89 and 11.7 lm/W, respectively.

Micro and nanostructural analysis of a human tooth using correlated focused ion beam (FIB) and transmission Electron microscopy (TEM) investigations.

In this study, natural molar human tooth specimens were investigated for determining their micro- and nanoscale structural morphology, chemistry and crystallinity. The differences were tracked comparatively for both enamel and dentin layers and at their interfaces. Although dental material structures are hard and tough and the cross-sectioning of these materials using mechanical methods is challenging, FIB-SEM dual-beam instruments serve for preparing ultra-thin homogenous lamella sections. In this work, both FIB-SEM and TEM based advanced characterization methods were applied to reveal different morphological characteristics of dental tissue via complementary imaging and diffraction analysis. In addition, SEM-EDS and Raman spectroscopy techniques provided additional information about the elemental distribution and the chemical composition differences of the dental tissues. According to electron microscopy examinations at the intersection between the enamel and the dentin layers, it was shown that the enamel was denser and polycrystalline, while the dentin layer was porous, fibrillar and of negligible long-range order, due to its tubular structure and organic components. In particular, EDS mapping and linescan analyses showed almost no differences in the elemental distribution. Raman results confirmed that both tissues had similar chemical composition except dentin showed spectral background effects in the spectrum due to its tubular structure and organic components.

Effective Neural Photostimulation Using Indium-Based Type-II Quantum Dots.

Light-induced stimulation of neurons via photoactive surfaces offers rich opportunities for the development of therapeutic methods and high-resolution retinal prosthetic devices. Quantum dots serve as an attractive building block for such surfaces, as they can be easily functionalized to match the biocompatibility and charge transport requirements of cell stimulation. Although indium-based colloidal quantum dots with type-I band alignment have attracted significant attention as a nontoxic alternative to cadmium-based ones, little attention has been paid to their photovoltaic potential as type-II heterostructures. Herein, we demonstrate type-II indium phosphide/zinc oxide core/shell quantum dots that are incorporated into a photoelectrode structure for neural photostimulation. This induces a hyperpolarizing bioelectrical current that triggers the firing of a single neural cell at 4 µW mm-2, 26-fold lower than the ocular safety limit for continuous exposure to visible light. These findings show that nanomaterials can induce a biocompatible and effective biological junction and can introduce a route in the use of quantum dots in photoelectrode architectures for artificial retinal prostheses.

Structural control of InP/ZnS core/shell quantum dots enables high-quality white LEDs.

Herein, we demonstrate that the structural and optical control of InP-based quantum dots (QDs) can lead to high-performance light-emitting diodes (LEDs). Zinc sulphide (ZnS) shells passivate the InP QD core and increase the quantum yield in green-emitting QDs by 13-fold and red-emitting QDs by 8-fold. The optimised QDs are integrated in the liquid state to eliminate aggregation-induced emission quenching and we fabricated white LEDs with a warm, neutral and cool-white appearance by the down-conversion mechanism. The QD-functionalized white LEDs achieve luminous efficiency (LE) up to 14.7 lm W-1 and colour-rendering index up to 80. The structural and optical control of InP/ZnS core/shell QDs enable 23-fold enhancement in LE of white LEDs compared to ones containing only QDs of InP core.

Focusing short-wavelength surface plasmons by a plasmonic mirror.

Emerging applications in nanotechnology, such as superresolution imaging, ultra-sensitive biomedical detection, and heat-assisted magnetic recording, require plasmonic devices that can generate intense optical spots beyond the diffraction limit. One of the important drawbacks of surface plasmon focusing structures is their complex design, which is significant for ease of integration with other nanostructures and fabrication at low cost. In this study, a planar plasmonic mirror without any nanoscale features is investigated that can focus surface plasmons to produce intense optical spots having lateral and vertical dimensions of λ/9.7 and λ/80, respectively. Intense optical spots beyond the diffraction limit were produced from the plasmonic parabolic mirror by exciting short-wavelength surface plasmons. The refractive index and numerical aperture of the plasmonic parabolic mirror were varied to excite short-wavelength surface plasmons. Finite-element method simulations of the plasmonic mirror and scanning near-field optical microscopy experiments have shown very good agreement.

Stokes-Shift-Engineered Indium Phosphide Quantum Dots for Efficient Luminescent Solar Concentrators.

Luminescent solar concentrators (LSCs) show promise because of their potential for low-cost, large-area, and high-efficiency energy harvesting. Stokes shift engineering of luminescent quantum dots (QDs) is a favorable approach to suppress reabsorption losses in LSCs; however, the use of highly toxic heavy metals in QDs constitutes a serious concern for environmental sustainability. Here, we report LSCs based on cadmium-free InP/ZnO core/shell QDs with type-II band alignment that allow for the suppression of reabsorption by Stokes shift engineering. The spectral emission and absorption overlap was controlled by the growth of a ZnO shell on an InP core. At the same time, the ZnO layer also facilitates the photostability of the QDs within the host matrix. We analyzed the optical performance of indium-based LSCs and identified the optical efficiency as 1.45%. The transparency, flexibility, and cadmium-free content of the LSCs hold promise for solar window applications.

Conformation-mediated Förster resonance energy transfer (FRET) in blue-emitting polyvinylpyrrolidone (PVP)-passivated zinc oxide (ZnO) nanoparticles.

Homopolymers, such as polyvinylpyrrolidone (PVP), are commonly used to passivate the surface of blue-light emitting ZnO nanoparticles during colloid nucleation and growth. However, although PVP is known to auto-fluoresce at 400nm, which is near the absorption edge of ZnO, the impact of PVP adsorption characteristics on the surface of ZnO and the surface-related photophysics of PVP-capped ZnO nanoparticles is not well understood. To investigate, we have synthesized ZnO nanoparticles in solvents containing PVP of 3 concentrations-0.5, 0.7, and 0.11gmL-1. Using time-domain NMR, we show that the adsorbed polymer conformation differs with polymer concentration-head-to-tail under low concentration (e.g., 0.05gmL-1) and looping, then train-like, with increasing concentration (e.g., 0.07gmL-1 and 0.11gmL-1, respectively). When the surface-adsorbed PVP is entrained, the surface states of ZnO are passivated and radiative emission from surface trap states is suppressed, allowing emission to be dominated by exciton transitions in the UV (ca. 310nm). Moreover, the reduced proximity between the PVP molecule and the ZnO gives rise to increased efficiency of energy transfer between the exciton emission of ZnO and the HOMO-LUMO absorption of PVP (ca. 400nm). As a result, light emission in the blue is enhanced in the PVP-capped ZnO nanoparticles. We thus show that the emission properties of ZnO can be tuned by controlling the adsorbed PVP conformation on the ZnO surface via the PVP concentration in the ZnO precipitation medium.

Nanoscale elastic modulus variation in loaded polymeric micelle reactors.

Tapping mode atomic force microscopy (TM-AFM) enables mapping of chemical composition at the nanoscale by taking advantage of the variation in phase angle shift arising from an embedded second phase. We demonstrate that phase contrast can be attributed to the variation in elastic modulus during the imaging of zinc acetate (ZnAc)-loaded reverse polystyrene-block-poly(2-vinylpyridine) (PS-b-P2VP) diblock co-polymer micelles less than 100 nm in diameter. Three sample configurations were characterized: (i) a 31.6 µm thick polystyrene (PS) support film for eliminating the substrate contribution, (ii) an unfilled PS-b-P2VP micelle supported by the same PS film, and (iii) a ZnAc-loaded PS-b-P2VP micelle supported by the same PS film. Force-indentation (F-I) curves were measured over unloaded micelles on the PS film and over loaded micelles on the PS film, using standard tapping mode probes of three different spring constants, the same cantilevers used for imaging of the samples before and after loading. For calibration of the tip geometry, nanoindentation was performed on the bare PS film. The resulting elastic modulus values extracted by applying the Hertz model were 8.26 ± 3.43 GPa over the loaded micelles and 4.17 ± 1.65 GPa over the unloaded micelles, confirming that phase contrast images of a monolayer of loaded micelles represent maps of the nanoscale chemical and mechanical variation. By calibrating the tip geometry indirectly using a known soft material, we are able to use the same standard tapping mode cantilevers for both imaging and indentation.

Solution-processed LiF for work function tuning in electrode bilayers.

Although ambient processing is the key to low-cost organic solar cell production, high-vacuum thermal evaporation of LiF is often a limiting step, motivating the exploration of solution processing of LiF as an alternative electrode interlayer. Submonolayer films are realized with the assistance of polymeric micelle reactors that enable LiF particle deposition with controlled nanoscale surface coverage. Scanning Kelvin probe reveals a work function tunable with nanoparticle coverage with higher values than that of bare indium tin oxide (ITO).

Unidirectional broadband radiation of honeycomb plasmonic antenna array with broken symmetry.

Emerging plasmonic and photovoltaic applications benefit from effective interaction between optical antennas and unidirectional incident light over a wide spectrum. Here, we propose a honeycomb array of plasmonic nanoantennas with broken symmetry to obtain a unidirectional radiation pattern over a wide spectrum. The honeycomb nanoantenna array is based on a hexagonal grid with periodically arranged nanostructure building blocks. To analyze the far-field optical distribution and spectral behavior of the plasmonic antenna honeycomb, a two-dimensional Wigner-Seitz unit cell is used together with periodic boundary conditions. As a result of the vectoral superposition of the fields produced by the Wigner-Seitz unit cells, far-zone optical fields interfere constructively or destructively in different directions. The constructive interference along the array's normal direction engenders unidirectional radiation. Due to the broken symmetry of the Wigner-Seitz cell, multiple resonances are supported by the plasmonic antenna honeycomb array over a broad spectrum.

Determining the morphology of polystyrene-block-poly(2-vinylpyridine) micellar reactors for ZnO nanoparticle synthesis.

We report the use of reverse PS-b-P2VP diblock copolymer micelles as true nanoscale-sized reactor vessels to synthesize ZnO nanoparticles. The reverse micelles were formed in toluene and then sequentially loaded with zinc acetate dihydrate and tetramethylammonium hydroxide reactants. Moreover, high spatial resolution Z-contrast imaging and EDX spectroscopy techniques were used to confirm the segregation of the Zn cation to the core of the loaded micelles. Determining the chemical distribution with high nanoscale spatial resolution is shown to complement the less direct characterization by AFM, DLS and FTIR, thus demonstrating broader implications for the characterization of hybrid nanocomposite systems.

Nanoscale composition mapping of segregation in micelles with tapping-mode atomic force microscopy.

Under energy-dissipative cantilevered tip-sample interaction, phase imaging using tapping-mode atomic force microscopy enables compositional mapping of composites containing a harder inorganic phase at the nanometer scale, embedded in a polymer matrix. The contrast in the phase images is shown to be dependent on the variation in the elastic properties of the diblock copolymer reverse micelles loaded with zinc acetate. Tapping conditions are also shown to determine whether the contrast is positive or negative for the harder core of the loaded micelles, based on the competition between attractive and repulsive tip-sample interaction forces. The broader implications are significant for scanning probe microscopy of other soft materials systems containing the segregation of a harder phase.