3D Low-Cost Equipment for Automated Peritoneal Dialysis Therapy.

A breakthrough in peritoneal dialysis (PD) therapy occurred in 1977 with the development of continuous ambulatory peritoneal dialysis (CAPD). Its simplicity, low cost, and ease with which CAPD could be performed on patients at home contributed to the popularity of this procedure. However, there is a need for continuous improvement in building optimal systems for incident chronic kidney disease (CKD) patients. This research showed the design and construction of a simplified prototype of low-cost automated peritoneal dialysis (APD) equipment that meets international standards to automatically regulate infusion and fluid drainage in and out of a patient with low margins of error. Experimental tests allowed the adjustment of the RPM values concerning the flow rate provided. In addition, thanks to the pressure sensor, it was possible to observe a fluctuation ranging from 9 to 13 kPa, which is within the permissible average specified in the catalogs of medical instruments and equipment. Furthermore, a turbidity sensor was added to decrease the possibility of presenting peritonitis. The results showed absolute values of flow, angular velocity, and pressure that it could deliver for use in APD therapies. Finally, the construction of the APD equipment is presented generally, showing the electronic and mechanical components that constitute it.

Bone Fractures Numerical Analysis in a Femur Affected by Osteogenesis Imperfecta.

This work presents a non-invasive methodology to obtain a three-dimensional femur model of three-year-old infants affected with Osteogenesis Imperfecta (OI) type III. DICOM® Files of a femur were processed to obtain a finite element model to assess the transverse, the oblique, and the comminuted fractures. The model is evaluated under a normal walking cycle. The loads applied were considered the most critical force generated on the normal walking cycle, and the analyses considered anisotropic bone conditions. The outcome shows stress concentration areas in the central zone of the diaphysis of the femur, and the highest levels of stress occur in the case of the comminuted fracture, while the transverse fracture presents the lowest values. Thus, the method can be helpful for determining the bone fracture behavior of certain pathologies, such as osteogenesis imperfecta, osteopenia, and osteoporosis.

Design of an Automated Multiposition Dynamic Wheelchair.

This work presents a design for an automatized multiposition dynamic wheelchair used to transport quadriplegic patients by reconfiguring a manual wheelchair structure. An electric actuator is attached to a four-bar mechanism fixed to each side of a wheelchair's backrest to reach multiposition. The entire device is actuated through a PID controller. An experimental test is carried out in a simplified wheelchair structure. Finally, the structure of the wheelchair is evaluated through the Dynamic analysis and Finite Element Method under the payload computed with the most critical position reached by the mechanism.

Redesign of a Piston for a Diesel Combustion Engine to Use Biodiesel Blends.

Biofuels represent an energy option to mitigate polluting gases. However, technical problems must be solved, one of them is to improve the combustion process. In this study, the geometry of a piston head for a diesel engine was redesigned. The objective was to improve the combustion process and reduce polluting emissions using biodiesel blends as the fuel. The methodology used was the mechanical engineering design process. A commercial piston (base piston) was selected as a reference model to assess the piston head's redesign. Changes were applied to the profile of the piston head based on previous research and a new model was obtained. Both models were evaluated and analyzed using the finite element method, where the most relevant physical conditions were temperature and pressure. Numerical simulations in the base piston and the new piston redesign proposal presented similar behaviors and results. However, with the proposed piston, it was possible to reduce the effort and the material. The proposed piston profile presents adequate results and behaviors. In future, we suggest continuing conducting simulations and experimental tests to assess its performance.

Continuous Microalgal Cultivation for Antioxidants Production.

Microalgae, including cyanobacteria, represent a valuable source of natural compounds that have remarkable bioactive properties. Each microalga species produces a mixture of antioxidants with different amounts of each compound. Three aspects are important in the production of bioactive compounds: the microalga species, the medium composition including light supplied and the photobioreactor design, and operation characteristics. In this study, the antioxidant content and productivity performance of four microalgae were assessed in batch and continuous cultures. Biomass productivity by the four microalgae was substantially enhanced under continuous cultivation by 5.9 to 6.3 times in comparison with batch cultures. The energetic yield, under the experimental conditions studied, ranged from 0.03 to 0.041 g biomass kJ-1. Phenols, terpenoids, and alkaloids were produced by Spirulinaplatensis, Isochrysisgalbana, and Tetraselmissuecica, whereas tocopherols and carotenoids were produced by the four microalgae, except for phycocyanin and allophycocyanin, which were only produced by S. platensis and Porphyridiumcruentum. The findings demonstrate that the continuous cultivation of microalgae in photobioreactors is a convenient method of efficiently producing antioxidants.