Muscle and joint function in the rotator cuff deficient shoulder.

Full-thickness rotator cuff tears can lead to poor coaptation of the humeral head to the glenoid, disrupting muscle forces required for glenohumeral joint stability, ultimately leading to joint subluxation. The aim of this study was to evaluate muscle forces and glenohumeral joint translations during elevation in the presence of isolated and combined full-thickness rotator cuff tears. Eight fresh-frozen upper limbs were mounted to a computer-controlled testing apparatus that simulated joint motion by simulated muscle force application. Scapular-plane abduction was performed, and glenohumeral joint translations were measured using an optoelectronic system. Testing was performed in the native shoulder, a following an isolated tear to the supraspinatus, as well as combined tears involving the supraspinatus and subscapularis, as well as supraspinatus, infraspinatus, and teres minor. Rotator cuff tears significantly increased middle deltoid force at 30°, 60°, and 90° of abduction relative to that in the native shoulder (p < 0.05). Significantly greater superior translations were observed relative to the intact shoulder due to combined tears to the supraspinatus and infraspinatus at 30° of abduction (mean increase: 1.6 mm, p = 0.020) and 60° of abduction (mean increase: 4.8 mm, p = 0.040). This study illustrates the infraspinatus-teres minor complex as a major humeral head depressor and contributor to glenohumeral joint stability. An increase in deltoid force during abduction occurs in the presence of rotator cuff tears, which exacerbates superior migration of the humeral head. The findings may help in the development of clinical tests in rotator cuff tear diagnostics, in surgical planning of rotator cuff repair, and in planning of targeted rehabilitation.

Subacromial contact after acromioplasty in the rotator cuff deficient shoulder.

Subacromial impingement (SAI) is associated with shoulder pain and dysfunction and is exacerbated by rotator cuff tears; however, the role of acromioplasty in mitigating subacromial contact in the rotator cuff deficient shoulder remains debated. This study aimed to quantify the influence of isolated and combined tears involving the supraspinatus on subacromial contact during abduction; and second, to evaluate the influence of acromioplasty on joint space size and subacromial contact under these pathological conditions. Eight fresh-frozen human cadaveric upper limbs were mounted to a computer-controlled testing apparatus that simulated joint motion by simulated force application. Shoulder abduction was performed while three-dimensional joint kinematics was measured using an optoelectronic system, and subacromial contact evaluated using a digital pressure sensor secured to the inferior acromion. Testing was performed after an isolated tear to the supraspinatus, as well as tears involving the subscapularis and infraspinatus-teres minor, both before and after acromioplasty. Rotator cuff tears significantly increased peak subacromial pressure (p < 0.001), average subacromial pressure (p = 0.001), and contact force (p = 0.034) relative to those in the intact shoulder. Following acromioplasty, significantly lower peak subacromial contact pressure, force and area were observed for all rotator cuff tears involving the supraspinatus at 30° of abduction (p < 0.05). Acromioplasty predominantly reduces acromion thickness anteriorly thereby reducing subacromial contact in the rotator cuff deficient shoulder, particularly in early to mid-abduction where superior glenohumeral joint shear force potential is large. These findings provide a biomechanical basis for acromioplasty as an intervention for SAI syndrome and as an adjunct to rotator cuff repairs.

Depth camera-based model for studying the effects of muscle loading on distal radius fracture healing.

BACKGROUND: Distal radius fractures (DRFs) treated with volar locking plates (VLPs) allows early rehabilitation exercises favourable to fracture recovery. However, the role of rehabilitation exercises induced muscle forces on the biomechanical microenvironment at the fracture site remains to be fully explored. The purpose of this study is to investigate the effects of muscle forces on DRF healing by developing a depth camera-based fracture healing model. METHOD: First, the rehabilitation-related hand motions were captured by a depth camera system. A macro-musculoskeletal model is then developed to analyse the data captured by the system for estimating hand muscle and joint reaction forces which are used as inputs for our previously developed DRF model to predict the tissue differentiation patterns at the fracture site. Finally, the effect of different wrist motions (e.g., from 60° of extension to 60° of flexion) on the DRF healing outcomes will be studied. RESULTS: Muscle and joint reaction forces in hands which are highly dependent on hand motions could significantly affect DRF healing through imposed compressive and bending forces at the fracture site. There is an optimal range of wrist motion (i.e., between 40° of extension and 40° of flexion) which could promote mechanical stimuli governed healing while mitigating the risk of bony non-union due to excessive movement at the fracture site. CONCLUSION: The developed depth camera-based fracture healing model can accurately predict the influence of muscle loading induced by rehabilitation exercises in distal radius fracture healing outcomes. The outcomes from this study could potentially assist osteopathic surgeons in designing effective post-operative rehabilitation strategies for DRF patients.

Effect of uncertain clinical conditions on the early healing and stability of distal radius fractures.

BACKGROUND AND OBJECTIVES: The healing outcomes of distal radius fracture (DRF) treated with the volar locking plate (VLP) depend on surgical strategies and postoperative rehabilitation. However, the accurate prediction of healing outcomes is challenging due to a range of certainties related to the clinical conditions of DRF patients, including fracture geometry, fixation configuration, and physiological loading. The purpose of this study is to investigate the influence of uncertainty and variability in fracture/fixation parameters on the mechano-biology and biomechanical stability of DRF, using a probabilistic numerical approach based on the results from a series of experimental tests performed in this study. METHODS: Six composite radius sawboneses fitted with titanium VLP (VLP 2.0, Austofix) were loaded to failure at a rate of 2 N/s. The testing results of the elastic and plastic behaviour of the VLP were used as inputs for a probabilistic-based computational model of DRF, which simulated mechano-regulated tissue differentiation and fixation elastic capacity at the fracture site. Finally, the probability of success in early indirect healing and fracture stabilisation was predicted. RESULTS: The titanium VLP is a strong and ductile fixation whose flexibility and elastic capacity are governed by flexion working length and bone-to-plate distance, respectively. A fixation with optimised designs and configurations is critical to mechanically stabilising the early fracture site. Importantly, the uncertainty and variability in fracture/fixation parameters could compromise early DRF healing. The physiological loading uncertainty is the most adverse factor, followed by the negative impact of uncertainty in fracture geometry. CONCLUSIONS: The VRP 2.0 fixation made of grade II titanium is a desirable fixation that is strong enough to resist irreparable deformation during early recovery and is also ductile to deform plastically without implant failure at late rehabilitation.

Outcomes of conservative treatment of acromial and scapular spine stress fracture post reverse shoulder arthroplasty: a systematic review with meta-analysis.

INTRODUCTION: Acromial and scapular spine stress fractures are common complications post reverse shoulder arthroplasty. A systematic review with meta-analysis was conducted to evaluate the clinical outcomes of conservatively treated acromial and scapular spine stress fractures post reverse shoulder arthroplasty in comparison to nonfracture control. METHODS: Embase, MEDLINE, and Web of Science were searched on September 9, 2022, using various terms related to fracture, acromion, scapula, and reverse shoulder arthroplasty. Meta-analysis using a random effects model was performed on common outcome scores. Risk of bias was assessed using the Joanna Briggs Institute tools for case-controlled studies. Sensitivity analysis was performed for imputed standard deviations and studies with <20 participants. RESULTS: Thirteen studies with a total of 339 fracture and 3142 control patients were included in the systematic review. Meta-analysis was performed on 12 studies assessing active forward flexion, abduction, external rotation, Constant-Murley score, American Shoulder and Elbow Surgeons Standardized Shoulder Assessment Form, pain score, Simple Shoulder Test, and Single Assessment Numeric Evaluation. Fracture patients experienced significantly poorer functional outcome compared with control patients when the fractures were managed conservatively. Levy III fractures tend to experience worse outcomes. Pain score did not demonstrate a statistically significant difference between the fracture and nonfracture cohort. DISCUSSION: Currently, literature regarding surgical management is lacking, partially because of a dearth of high-quality literature but also hindered by a lack of standardized techniques. This review was limited by inclusion of studies of low evidence, small sample sizes, and inconsistency in outcome measurement and follow-up period. Overall, patients with acromial and scapular spine stress fractures treated conservatively are expected to have reduced shoulder function compared to nonfracture patients, with the spine of scapula fracture patients suffering the poorest outcomes. Future studies should aim to use the same sets of outcomes parameters to assess the patients at fixed time intervals and report outcomes stratified by Levy classification. This will enable interinstitutional collaboration and pooling of results.

Development of numerical model-based machine learning algorithms for different healing stages of distal radius fracture healing.

BACKGROUND AND OBJECTIVES: Early therapeutic exercises are vital for the healing of distal radius fractures (DRFs) treated with the volar locking plate. However, current development of rehabilitation plans using computational simulation is normally time-consuming and requires high computational power. Thus, there is a clear need for developing machine learning (ML) based algorithms that are easy for end-users to implement in daily clinical practice. The purpose of the present study is to develop optimal ML algorithms for designing effective DRF physiotherapy programs at different stages of healing. METHOD: First, a three-dimensional computational model for the healing of DRF was developed by integrating mechano-regulated cell differentiation, tissue formation and angiogenesis. The model is capable of predicting time-dependant healing outcomes based on different physiologically relevant loading conditions, fracture geometries, gap sizes, and healing time. After being validated using available clinical data, the developed computational model was implemented to generate a total of 3600 clinical data for training the ML models. Finally, the optimal ML algorithm for each healing stage was identified. RESULTS: The selection of the optimal ML algorithm depends on the healing stage. The results from this study show that cubic support vector machine (SVM) has the best performance in predicting the healing outcomes at the early stage of healing, while trilayered ANN outperforms other ML algorithms in the late stage of healing. The outcomes from the developed optimal ML algorithms indicate that Smith fractures with medium gap sizes could enhance the healing of DRF by inducing larger cartilaginous callus, while Colles fractures with large gap sizes may lead to delayed healing by bringing excessive fibrous tissues. CONCLUSIONS: ML represents a promising approach for developing efficient and effective patient-specific rehabilitation strategies. However, ML algorithms at different healing stages need to be carefully chosen before being implemented in clinical applications.

Influence of muscle loading on early-stage bone fracture healing.

Designing weight-bearing exercises for patients with lower-limb bone fractures is challenging and requires a systematic approach that accounts for patient-specific loading conditions. However, 'trial-and-error' approaches are commonplace in clinical settings due to the lack of a fundamental understanding of the effect of weight-bearing exercises on the bone healing process. Whilst computational modelling has the potential to assist clinicians in designing effective patient-specific weight-bearing exercises, current models do not explicitly account for the effects of muscle loading, which could play an important role in mediating the mechanical microenvironment of a fracture site. We combined a fracture healing model involving a tibial fracture stabilised with a locking compression plate (LCP) with a detailed musculoskeletal model of the lower limb to determine interfragmentary strains in the vicinity of the fracture site during both full weight-bearing (100% body weight) and partial weight-bearing (50% body weight) standing. We found that muscle loading significantly altered model predictions of interfragmentary strains. For a fractured bone with a standard LCP configuration (bone-plate distance = 2 mm, working length = 30 mm) subject to full weight-bearing, the predicted strains at the near and far cortices were 23% and 11% higher when muscle loading was included compared to the case when muscle loading was omitted. The knee and ankle muscles accounted for 38% of the contact force exerted at the knee joint during quiet standing and contributed significantly to the strains calculated at the fracture site. Thus, models of bone fracture healing ought to account explicitly for the effects of muscle loading. Furthermore, the study indicated that LCP configuration parameters play a crucial role in influencing the fracture site microenvironment. The results highlighted the dominance of working length over bone-plate distance in controlling the flexibility of fracture sites stabilised with LCP devices.

The effects of mechanical instability on PDGF mediated inflammatory response at early stage of fracture healing under diabetic condition.

BACKGROUND AND OBJECTIVE: Mechanical stability plays an important role in fracture healing process. Excessive interfragmentary movement will continuously damage the tissue and newly formed capillaries at the fracture site, which leads to overproduction of platelet-derived growth factor (PDGF) that attracts more macrophages into fracture callus, ultimately persistent and enhanced inflammatory response happens. For diabetic condition, the impact of mechanical instability of fracture site on inflammatory response could be further compliciated and the relevant research in this field is relatively limited. METHODS: Building on previous experimental studies, this study presents a numerical model consisting of a system of reactive-transport equations representing the transport as well as interactions of different cells and cytokines within the fracture callus. The model is initially validated by available experimental data, and then implemented to investigate the role of mechanical stability of fracture site in inflammatory response during early stage of healing. It is assumed that there is an increased release of PDGF due to the rupture of blood vessels resulting from mechanical instability, which leads to increased production of inflammatory cytokines (i.e., TNF-α). The bone healing process under three different conditions were investigated, i.e., mechanically stable condition with normal inflammatory response (Control, Case 1), mechanically unstable condition with normal inflammatory response (Case 2) and mechanically unstable condition with diabetes (Case 3). RESULTS: Mechanical instability can promote the macrophage infiltration and thus induce an enhanced and prolonged inflammatory response, which could impede the MSCs proliferation during the early fracture healing stage (e.g., compared with the control condition, the MSCs concentration in unstable fracture with normal inflammatory response can be reduced by 3.2% and 5.2% on day 2 and day 10 post-fracture, respectively). Under diabetic condition, the mechanical instability of fracture site could lead to a significant increase of TNF-α concentration in fracture callus (Case 3) in comparison to control (Case 1) (e.g., three-fold increase in TNF-α concentration compared to control). In addition, the results show that the mechanical instability affects the cell differentiation and proliferation in fracture callus in a spatially dependent manner, e.g., for diabetic fracture patients, the mechanical instability could potentially decrease the concentration of MSCs, osteoblasts and chondrocytes by around 39%, 30% and 29% in cortical callus, respectively, in comparison to control. CONCLUSION: The mechanical instability together with diabetic condition can significantly affect the natural resolution of inflammation during early stage of healing by turning acute inflammation into chronic inflammation which is characterized by a continuously upregulated TNF-α pathway.

Motorized Intramedullary Nail Lengthening in the Older Population.

Limb lengthening has not been widely employed in the elderly population due to concerns that outcomes will be inferior. The purpose of this multicenter, retrospective case-control series was to report the bone healing outcomes and complications of lower limb lengthening in older patients (≥60 years) using magnetic intramedullary lengthening nail (MILN). Our hypothesis was that healing parameters including consolidation days, the consolidation index, maturation days, and the maturation index, as well as the number of adverse events reported in the older population, would be no different to those of the general adult population. We retrospectively reviewed charts and radiographs from patients ≥60 years of age with limb-length discrepancies who underwent femoral or tibial lengthening using a MILN. Parameters were compared among the age categories "≤19 years," "20-39 years," "40-59 years," or "≥60 years" and propensity-matched cohorts for the age groups 20-59 years and ≥60 years. Complications were reported as percentages for each age category. In the study period, 354 MILN were placed in 257 patients. Sixteen nails were placed in patients 60 years of age or older (mean 65 ± 5 years; range 60-72 years). Comparisons of healing parameters showed no difference between those aged 60+ and the younger cohort. Complication percentages were not statistically significant (p = 0.816). Limb lengthening with MILN may therefore be considered a safe and feasible option for a generally healthy elderly population.

Influence of therapeutic grip exercises induced loading rates in distal radius fracture healing with volar locking plate fixation.

BACKGROUND AND OBJECTIVE: Therapeutic exercises could potentially enhance the healing of distal radius fractures (DRFs) treated with volar locking plate (VLP). However, the healing outcomes are highly dependant on the patient-specific fracture geometries (e.g., gap size) and the loading conditions at the fracture site (e.g., loading frequency) resulted from different types of therapeutic exercises. The purpose of this study is to investigate the effects of different loading frequencies induced by therapeutic exercises on the biomechanical microenvironment of the fracture site and the transport of cells and growth factors within the fracture callus, ultimately the healing outcomes. This is achieved through numerical modelling and mechanical testing. METHODS: Five radius sawbones specimens (Pacific Research Laboratories, Vashon, USA) fixed with VLP (VRP2.0+, Austofix) were mechanically tested using dynamic test instrument (INSTRON E3000, Norwood, MA). The loading protocol used in mechanical testing involved a series of cyclic axial compression tests representing hand and finger therapeutic exercises. The relationship between the dynamic loading rate (i.e., loading frequency) and dynamic stiffness of the construct was established and used as inputs to a developed numerical model for studying the dynamic loading induced cells and growth factors in fracture site and biomechanical stimuli required for healing. RESULTS: There is a strong positive linear relationship between the loading rate and axial stiffness of the construct fixed with VLP. The loading rates induced by the moderate frequencies (i.e., 1-2 Hz) could promote endochondral ossification, whereas relatively high loading frequencies (i.e., over 3 Hz) may hinder the healing outcomes or lead to non-union. In addition, a dynamic loading frequency of 2 Hz in combination of a fracture gap size of 3 mm could produce a better healing outcome by enhancing the transport of cells and growth factors at the fracture site in comparison to free diffusion (i.e. without loading), and thereby produces a biomechanical microenvironment which is favourable for healing. CONCLUSION: The experimentally validated numerical model presented in this study could potentially contribute to the design of effective patient-specific therapeutic exercises for better healing outcomes. Importantly, the model results demonstrate that therapeutic grip exercises induced dynamic loading could produce a better biomechanical microenvironment for healing without compromising the mechanical stability of the overall volar locking plate fixation construct.

Role of TNF-α in early-stage fracture healing under normal and diabetic conditions.

BACKGROUND AND OBJECTIVE: Inflammatory response plays a crucial role in the early stage of fracture healing. Immediately after fracture, the debris and immune cells (e.g., macrophages), recruited into the fracture callus, lead to the secretion of inflammatory cytokines, such as tumor necrosis factor-alpha (TNF-α), which governs the mesenchymal stem cells (MSCs) mediated healing processes. However, it is still unclear how chronic inflammatory diseases (e.g., diabetes) affect the level of TNF-α in fracture callus, ultimately the healing outcomes at the early stage of healing. Therefore, the purpose of this study is to develop a numerical model for investigating TNF-α mediated bone fracture healing. METHODS: A mathematical model consisting of a system of partial differential equations that represent the reactive transport of cells and cytokines in the fracture callus is developed in this study. The model is first calibrated by using available experimental data and then implemented to study the effect of TNF-α on the early stage of fracture healing under normal and diabetic conditions. RESULTS: There is a significant elevation of TNF-α level in facture callus during the first 24 h post-fracture in normal condition, and its influence in the concentration of MSCs and cell differentiation becomes significant three days post-fracture (e.g., the absence of TNF-α signaling could reduce the concentration of MSCs more than 20% in cortical callus). In addition, the excessive secretion of TNF-α induced by diabetes could decrease the concentration of MSCs at the initial stage of healing, particularly reduce the concentration of MSCs in cortical callus by around 25%. CONCLUSION: The model predictions suggested that there should be an optimal concentration of TNF-α in fracture callus, which enhances the early stage of healing, and excessive or insufficient secretion of TNF-α might significantly hinder the healing process.

Optimal time-dependent levels of weight-bearing for bone fracture healing under Ilizarov circular fixators.

It is known that weight-bearing exercises under Ilizarov circular fixators (ICF) could enhance bone fracture healing by mechano-regulation. However, interfragmentary movements at the fracture site induced by weight-bearing may inhibit angiogenesis and ultimately delay the healing process. To tackle this challenge, a computational model is presented in this study which considers the spatial and temporal changes in mechanical properties of fracture callus to predict optimal levels of weight-bearing during fracture healing under ICF. The study takes sheep fractures as example and shows that the developed model has the capability of predicting patient specific, time-dependent optimal levels of weight-bearing which enhances mechano-regulation mediated healing without hindering the angiogenesis process. The results demonstrate that allowable level of weight-bearing and timings depend on fracture gap size. For normal body weights (BW) and moderate fracture gap sizes (e.g. 3 mm), weight-bearing with 30% BW could start by week 4 post-operation and gradually increase to 100% BW by week 11. In contrast, for relatively large fracture gap sizes (i.e. 6 mm), weight-bearing is recommended to commence in later stages of healing (e.g. week 11 post-operation). Furthermore, increasing ICF stiffness (e.g. using half pins instead of pretension wires) can increase the level of weight-bearing significantly in the early stages up to a certain time point (e.g. week 8 post-operation) beyond which no noticeable benefits could be achieved. The findings of this study have potential applications in designing post-operative weight bearing exercises.

Balance Between Mechanical Stability and Mechano-Biology of Fracture Healing Under Volar Locking Plate.

The application of volar locking plate (VLP) is promising in the treatment of dorsally comminuted and displaced fracture. However, the optimal balance between the mechanical stability of VLP and the mechanobiology at the fracture site is still unclear. The purpose of this study is to develop numerical models in conjunction with experimental studies to identify the favourable mechanical microenvironment for indirect healing, by optimizing VLP configuration and post-operative loadings for different fracture geometries. The simulation results show that the mechanical behaviour of VLP is mainly governed by the axial compression. In addition, the model shows that, under relatively large gap size (i.e., 3-5 mm), the increase of FWL could enhance chondrocyte differentiation while a large BPD could compromise the mechanical stability of VLP. Importantly, bending moment produced by wrist flexion/extension and torsion moment produced from forearm rotation could potentially hinder endochondral ossification at early stage of healing. The developed model could potentially assist orthopaedic surgeons in surgical pre-planning and designing post-operation physical therapy for treatment of distal radius fractures.

A probabilistic approach for modelling bone fracture healing under Ilizarov circular fixator.

Bone fracture treatments using Ilizarov circular fixator (ICF) involve dealing with uncertainties about a range of critical factors that control the mechanical microenvironment of the fracture site such as ICF configuration, fracture gap size, physiological loading etc. To date, the effects of the uncertainties about these critical factors on the mechanical microenvironment of the fracture site have not been fully understood. The purpose of this study is to tackle this challenge by using computational modelling in conjunction with engineering reliability analysis. Particularly, the effects of uncertainties in fracture gap size (GS), level of weight-bearing (P), ICF wire pretension (T) and wire diameter (WD) on the fracture site mechanical microenvironment at the beginning of the reparative phase of healing was investigated in this study. The results show that the mechanical microenvironment of fracture site stabilised with ICF is very sensitive to the uncertainties in P and GS. For example, an increase in the coefficient of variation of P (COVP ) from 0.1 to 0.9 (i.e., an increase in the uncertainty in P) could reduce the probability of achieving a favourable mechanical microenvironment within the fracture site (i.e., Probability of Success, PoS) by more than 50%, while an increase in the coefficient of variation of GS (COVGS ) from 0.1 to 0.9 could decrease PoS by around 30%. In contrast, an increase in the uncertainties in T and WD (COV increase from 0.1 to 0.9) has little influence on the fracture site mechanical microenvironment (PoS changes <5%).

Muscle and Joint Function After Anatomic and Reverse Total Shoulder Arthroplasty Using a Modular Shoulder Prosthesis.

Changes in joint architecture and muscle loading resulting from total shoulder arthroplasty (TSA) and reverse total shoulder arthroplasty (RSA) are known to influence joint stability and prosthesis survivorship. This study aimed to measure changes in muscle moment arms, muscle lines of action, as well as muscle and joint loading following TSA and RSA using a metal-backed uncemented modular shoulder prosthesis. Eight cadaveric upper extremities were assessed using a customized testing rig. Abduction, flexion, and axial rotation muscle moment arms were quantified using the tendon-excursion method, and muscle line-of-force directions evaluated radiographically pre-operatively, and after TSA and revision RSA. Specimen-specific musculoskeletal models were used to estimate muscle and joint loading pre- and post-operatively. TSA lateralized the glenohumeral joint center by 4.3 ± 3.2 mm, resulting in small but significant increases in middle deltoid force (2.0%BW) and joint compression during flexion (2.1%BW) (p < 0.05). Revision RSA significantly increased the moment arms of the major abductors, flexors, adductors, and extensors, and reduced their peak forces (p < 0.05). The superior inclination of the deltoid significantly increased while the inferior inclination of the rotator cuff muscles decreased (p < 0.05). TSA using an uncemented metal-backed modular shoulder prosthesis effectively restores native joint function; however, lateralization of the glenoid component should be minimized intra-operatively to mitigate increased glenohumeral joint loading and polyethylene liner contact stresses. Revision RSA reduces muscle forces required during shoulder function but produces greater superior joint shear force and less joint compression. The findings may help to guide component selection and placement to mitigate joint instability after arthroplasty. © 2019 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 37:1988-2003, 2019.

The Effects of Dynamic Loading on Bone Fracture Healing Under Ilizarov Circular Fixators.

Early weight bearing appears to enhance bone fracture healing under Ilizarov circular fixators (ICFs). However, the role of early weight bearing in the healing process remains unclear. This study aims to provide insights into the effects of early weight bearing on healing of bone fractures stabilized with ICFs, with the aid of mathematical modeling. A computational model of fracture site was developed using poro-elastic formulation to simulate the transport of mesenchymal stem cells (MSCs), fibroblasts, chondrocytes, osteoblasts, osteogenic growth factor (OGF), and chondrogenic growth factor (CGF) and MSC differentiation during the early stage of healing, under various combinations of fracture gap sizes (GS), ICF wire pretension forces, and axial loads. 1 h of physiologically relevant cyclic axial loading followed by 23 h of rest in the post-inflammation phase (i.e., callus with granulation tissue) was simulated. The results show that physiologically relevant dynamic loading could significantly enhance cell and growth factor concentrations in the fracture site in a time and spatially dependent manner. 1 h cyclic loading (axial load with amplitude, PA, of 200 N at 1 Hz) increased the content of chondrocytes up to 37% (in all zones of callus), CGF up to 28% (in endosteal and periosteal callus) and OGF up to 50% (in endosteal and cortical callus) by the end of the 24 h period simulated. This suggests that the synergistic effect of dynamic loading-induced advective transport and mechanical stimuli due to early weight bearing is likely to enhance secondary healing. Furthermore, the study suggests that relatively higher PA values or lower ICF wire pretension forces or smaller GS could result in increased chondrocyte and GF content within the callus.

Bone fracture healing under Ilizarov fixator: Influence of fixator configuration, fracture geometry, and loading.

This study aims to enhance the understanding of the relationship between Ilizarov fixator configuration and its effects on bone fracture healing. Using Taylor spatial frame (TSF) as an example, the roles of critical parameters (ie, TSF ring diameter, wire pre-tension, fracture gap size, and axial load) that govern fracture healing during the early stages were investigated by using computational modelling in conjunction with mechanical testing involving an advanced 3D optical measurement system. The computational model was first validated using the mechanical test results and then used to simulate mesenchymal stem cell (MSC) differentiations within different regions of the fracture site under various combinations of TSF ring diameter, wire pre-tension, fracture gap size, and axial load values. Predicted spatially dependent MSC differentiation patterns and the influence of each parameter on differentiations were compared with in vivo results, and good agreement was seen between the two. Gap size was identified as the most influential parameter in MSC differentiation, and the influence of axial loading and TSF configuration (ie, ring diameter and wire pre-tension) on cell differentiation was seen to be gap size dependent. Most changes in cell differentiation were predicted in the external callus (periosteal), which is the crucial region of the callus in the early stages. However, for small gap sizes (eg, 1 mm), significant changes were predicted in the endosteal callus as well. The study exhibits the potential of computational models in assessing the performance of Ilizarov fixators as well as assisting surgeons in patient-specific clinical treatment planning.

Rotator cuff contact pressures at the tendon-implant interface after anatomic total shoulder arthroplasty using a metal-backed glenoid component.

BACKGROUND: Rotator cuff tears following anatomic total shoulder arthroplasty increase with duration of follow-up. This study aimed to evaluate contact pressure between the rotator cuff tendons and prosthesis after anatomic total shoulder arthroplasty and compare these with the tendon-contact pressures in the native shoulder. METHODS: Eight entire upper extremities were mounted onto a testing apparatus, and simulated muscle loading was applied to each rotator cuff tendon with the shoulder positioned in abduction, internal rotation, and external rotation. Pressure-sensitive film placed between each tendon and bone was used to measure the resultant tendon contact pressures. Experiments were repeated after anatomic total shoulder arthroplasty using standardized implant sizes, and pressure-sensitive film was used to evaluate tendon-prosthesis contact pressure. RESULTS: Both joint angle and shoulder joint replacement surgery had significant effects on the maximum contact pressure measured between the humeral head and all rotator cuff tendons (P < .05) except the teres minor. The supraspinatus demonstrated a significantly larger peak tendon contact pressure after surgery at 45° of abduction relative to that in the native shoulder (mean difference, 0.2 MPa; P = .031), while the subscapularis had a significantly larger maximum contact pressure at 10° of abduction (mean difference, 0.45 MPa; P = .032) and 90° of abduction (mean difference, 0.80 MPa; P = .008) postoperatively. CONCLUSION: Anatomic total shoulder arthroplasty results in significantly larger tendon contact pressures relative to those in the native shoulder. High tendon contact pressures may ultimately predispose rotator cuff tendons to postoperative wear-induced damage and tearing.

Unicortical and bicortical plating in the fixation of comminuted fractures of the clavicle: a biomechanical study.

BACKGROUND: Intraoperative neurovascular complications with clavicle fracture fixation are often due to far cortex penetration by drills and screws, but could be avoided using a unicortical construct. The objective of this study was to compare the bending and torsional strength of a unicortical locking screw plate construct and a hybrid (with central locked and outer non-locked long oblique screws) unicortical plate construct for clavicle fracture fixation with that of a conventional bicortical locking screw construct of plate fixation. METHODS: Twenty-four human clavicle specimens were harvested and fractured in a comminuted mid-shaft butterfly configuration. Clavicles were randomly allocated to three surgical fixation groups: unicortical locking screw, bicortical locking screw and hybrid unicortical screw fixation. Clavicles were tested in torsion and cantilever bending. Construct bending and torsional stiffness were measured, as well as ultimate strength in bending. RESULTS: There were no significant differences in bending stiffness or ultimate bending moment between all three plating techniques. The unicortical locked construct had similar torsional stiffness compared with the bicortical locked construct; however, the hybrid technique was found to have significantly lower torsional stiffness to that of the bicortical locking screw construct (mean difference: 87.5 Nmm/degree, P = 0.028). CONCLUSIONS: Unicortical locked screw plate fixation and hybrid unicortical plating fixation with centrally locked screws and outer long, oblique screws may alleviate far cortex penetration, protecting nearby anatomical structures, and may ease implant removal and conversion to bicortical fixation for revision surgery; however, use of long oblique screws may increase the risk of early loosening under torsion.

An intramedullary Echidna pin for fixation of comminuted clavicle fractures: a biomechanical study.

BACKGROUND: Intramedullary fixation of comminuted mid-shaft clavicle fractures has traditionally been employed with satisfactory clinical outcomes; however, pins with smooth surfaces may protrude from the bone and are prone to migration, while some threaded pins are difficult to remove post-operatively. The aim of this proof-of-concept study was to develop and evaluate the biomechanical strength of a novel intramedullary Echidna pin device designed to maintain fracture reduction, resist migration and facilitate ease of post-operative removal. METHODS: Thirty human clavicle specimens were harvested and fractured in a comminuted mid-shaft butterfly configuration. Each specimen was randomly allocated to three surgical repair groups including intramedullary fixation using the Echidna pin and Herbert Cannulated Bone Screw System, as well as plate fixation using bi-cortical locking screws. Using a biomechanical testing apparatus, construct bending and torsional stiffness were measured, as well as ultimate bending strength. RESULTS: There was no significant difference in torsional stiffness and ultimate bending moment between the Echidna pin and Herbert screw repair constructs (p > 0.05); however, the Echidna pin construct demonstrated a significantly greater bending stiffness compared to that of the Herbert screw construct (mean difference 0.55 Nm/deg., p = 0.001). The plate construct demonstrated significantly greater torsional stiffness, bending stiffness and ultimate bending moment compared to those of the Herbert screw and Echidna pin (p < 0.05). CONCLUSIONS: An intramedullary Echidna pin device was designed to stabilize comminuted fractures of the clavicle, maintain fracture compression and provide ease of removal post-operatively. Since the results suggest equivalent or superior torsional and bending stability in the Echidna pin compared to that of the Herbert screw, the Echidna pin concept may represent an alternative fixation device to conventional intramedullary screws, nails and pins; however, superior plating using bi-cortical locking screws provides substantially higher construct structural rigidity than intramedullary devices, and may therefore be useful in cases of osteoporotic bone, or where high fracture stability is required.