Use of real-time monitors to evaluate the potential exposure of secondhand electronic cigarette particulate matter inside vehicles.

Electronic cigarette (ECIG) use continues to be highly prevalent, especially among youth and young adults. Potential exposure from secondhand ECIG particulate matter (PM) places bystanders in danger of inhaling harmful substances, especially in confined spaces. This study was conducted to measure the potential exposure from secondhand ECIG PM exposure in vehicles, with participants completing a 30-min ECIG use session in their own vehicle with their preferred ECIG device. Sessions included a 5-min, 10-puff directed bout (30-s interpuff interval), followed by a 25-min ad libitum bout in which participants could take as many puffs as desired. Real-time PM1, PM2.5, and PM10 (the 50% efficiency mass cut-off of that passes through a size-selective inlet at 1 µm, 2.5 µm, and 10 µm aerodynamic diameters, respectively) measurements were captured during the sessions using portable PM monitors (MiniWRAS, pDR, SidePak, and GeoAir2 low-cost monitors). A total of 56 participants with valid measurements were included in the study, with a total of 13 unique ECIG device brands, including Vuse Alto, Box Air Bar, ElfBar, Esco Bar, Aegis Legend, Hyde Edge, JUUL, Kang Onee Stick, Kang Onee Stick Plus, Nord X, Nord 2, Nord 3, and Vaporesso. During the 5-min directed bout, the highest real-time PM2.5 mean concentrations were 175 µg/m3 for the MiniWRAS, 1050 µg/m3 for pDR and 3314 µg/m3 for SidePak. The filter measurements were not detectable in most experiments, except for two participants, with one taking 205 puffs and the other taking 285 puffs, approximately 10 times the mean (30) puffs of all participants. The evaluation of GeoAir2 with the MiniWRAS showed a wide range of Pearson correlation coefficient (r) values, ranging from -0.03 to 1.00, for the 13 ECIG brands. The mass median diameter (0.31 µm-3.42 µm) and geometric standard deviation (2.47-8.21) were different based on the participants for the same ECIG brand.

Secondhand electronic cigarette aerosol in vehicles impacts indoor air quality.

BACKGROUND: Electronic cigarette (ECIG) use in vehicles represents a public health concern due to the potential for exposure to high concentrations of particulate matter (PM) and other toxicants. This study examined the impact of ECIG use on air quality in vehicles. METHODS: People who reported current ECIG use (n=60; mean age=20.5, SD=2.3) completed a brief survey and a 30-min ECIG use session in their own vehicle. Using a protocol similar to clinical laboratory studies involving tobacco use, participants took 10 directed puffs (i.e., a directed bout with one puff every 30s for 5min) followed by a 25-min ad libitum period in which participants took as many puffs as desired. PM 2.5µm in diameter or smaller (PM2.5) were measured using aerosol monitors set up to sample air from the breathing zone of the passenger seat and total puffs were recorded. The association between peak PM2.5 concentration and puff count was examined. RESULTS: Participants took a median 18 total puffs during the sessions. Median PM2.5 concentrations increased from 4.78µg/m3 at baseline to 107.40µg/m3 after the directed bout. Median peak PM2.5 concentration was 464.48µg/m3 and ranged from 9.56µg/m3 to 143,503.91µg/m3 (IQR=132.72-1604.68). After removing two extreme outliers for puff count and PM2.5 concentrations, puff count was significantly correlated with peak PM2.5 concentration during the ad libitum bout (r=0.32, p=0.015). CONCLUSIONS: ECIG use in vehicles impacts air quality negatively and may pose health risks to those present in vehicles when ECIG use is occurring.

Effects of E-Cigarette Liquid Ratios on the Gravimetric Filter Correction Factors and Real-Time Measurements.

Electronic cigarettes (ECIGs) generate high concentrations of particulate matter (PM), impacting the air quality inhaled by humans through secondhand exposure. ECIG liquids are available commercially and some users create their own "do-it-yourself" liquids, and these liquids often vary in the amounts of their chemical ingredients, including propylene glycol (PG) and vegetable glycerin (VG). Previous studies have quantified PM concentrations in ECIG aerosol generated from liquids containing different PG/VG ratios. However, the effects of these ratios on aerosol instrument filter correction factors needed to measure PM concentrations accurately have not been assessed. Thus, ECIG aerosol filter correction factors for multiple aerosol instruments (SMPS + APS, MiniWRAS, pDR, and SidePak) were determined for five different PG/VG ratios 1) 0PG/100VG, 2) 15PG/85VG, 3) 50PG/50VG, 4) 72PG/28VG, and 5) 90PG/10VG and two different PM sizes, PM1 (1 µm and smaller) and PM2.5 (2.5 µm and smaller). ECIG aerosols were generated inside a controlled exposure chamber using a diaphragm pump and a refillable ECIG device for all the ratios. In addition, the aerosol size distribution and mass median diameter were measured for all five ECIG ratios. PM2.5 correction factors (5-7.6) for ratios 1, 2, 3, and 4 were similar for the SMPS + APS combined data, and ratios 1, 2, 3 were similar for the MiniWRAS (~2), pDR (~0.5), and SidePak (~0.24). These data suggest different correction factors may need to be developed for aerosol generated from ECIGs with high PG content. The higher correction factor values for the 90PG/10VG ratio may have resulted from greater PG volatility relative to VG and sensor losses. The correction factors (ratios 1-4) for PM2.5 were SMPS + APS data (4.96-7.62), MiniWRAS (2.02-3.64), pDR (0.50-1.07), and SidePak (0.22-0.40). These data can help improve ECIG aerosol measurement accuracy for different ECIG mixture ratios.

Heavy metal ecotoxicology of vervet monkeys (Chlorocebus pygerythrus) across field sites in South Africa.

Primatologists use ecological models for understanding nonhuman primate (NHP) behavior and biology. Yet few studies have focused on the impacts of naturally occurring and anthropogenically derived toxicants in NHP habitats. For humans and NHPs, toxic levels of heavy metals frequently result in poor health outcomes including improper neurological development, immune system depression, and endocrine disruption. We analyzed the concentrations of lead (Pb), arsenic (As), and cadmium (Cd) in 48 vervet monkey (Chlorocebus pygerythrus) hair samples collected from eight South African groups living in environments with varying degrees of anthropogenic disturbance. We used two systems to categorize anthropogenic disturbance. The first was based on behavioral observations, home range overlap with human modified environments, and interviews with local people. The second system used stable isotope analysis (mean δ13C and δ15N hair values) from each group to estimate the consumption of C4 resources and the utilization of anthropogenically disturbed habitats. Preliminary analyses revealed differences in the Pb and As hair concentrations across the field sites (p < 0.05). Comparisons between anthropogenic disturbance using observations and interviews revealed differences in As (p < 0.01). In contrast, comparisons between categories using δ13C hair values revealed differences in Pb (p < 0.05). The results from this study suggest that multiple approaches using both qualitative and quantitative data should be employed to estimate the relationship between anthropogenic disturbance and environmental toxicants. Since many NHP populations share their habitats with humans, efforts to improve these landscapes would likely be beneficial for NHP and human health.

Laboratory Determination of Gravimetric Correction Factors for Real-time Area Measurements of Electronic Cigarette Aerosols.

Research on secondhand electronic cigarette (ECIG) aerosol exposure using aerosol monitors has demonstrated that ECIG use can generate high concentrations of particulate matter (PM) and impact indoor air quality. However, quantifying indoor air PM concentrations using real-time optical monitors with on-site calibration specifically for different PM exposures has not been established. Therefore, the ECIG aerosol filter correction factors were calculated for different PM sizes (PM1, PM2.5, and PM10) and different aerosol optical monitors, the MiniWRAS, pDR, and SidePak. ECIG aerosol generation was achieved using five ECIGs representing three ECIG types, disposable, pod-mod, and box mod. The aerosol size distribution by mass was measured for the five ECIGs during PM generation. Compared to the discrete filter measurements, the MiniWRAS performed the best when the concentrations were low, followed by the pDR and SidePak. The average PM concentrations and correction factor ranges for the different ECIGs were 323-1,775 µg/m3 and 0.64-6.01 for the MiniWRAS, 1,388-13,365 µg/m3 and 0.41-0.80 for the pDR, and 4,632-55,339 µg/m3 and 0.13-0.20 for the SidePak, respectively. The mass median diameter ranged from 0.41 and 0.62 µm, and most particles generated from the ECIGs were smaller than 1 µm. This study demonstrates that aerosol size distribution varies between ECIGs. Likewise, the correction factors developed for the real-time aerosol monitors are specific to the ECIG used. Thus, these data can help improve ECIG aerosol exposure measurement accuracy.

Increased JUUL Emissions from Initial Puffs after Removing and Reinserting Pod.

Standard laboratory electronic cigarette (ECIG) puffing protocols that do not consider user behaviors, such as removing and resinserting a pod, may underestimate emissions. This study compared JUUL emissions from four 10-puff bout procedures. We generated ECIG aerosol in a chamber using a JUUL device and measured concentrations of particulate matter ≤2.5 µm in diameter (PM2.5). The JUUL pod was removed and reinserted 0 times, 1 time, 4 times, and 9 times in experiments 1-4, respectively. Mean real-time PM2.5 concentration was 65.06 µg/m3 (SD = 99.53) for experiment 1, 375.50 µg/m3 (SD = 346.45) for experiment 2, 501.94 µg/m3 (SD = 450.00) for experiment 3, and 834.69 µg/m3 (SD = 578.34) for experiment 4. In this study, removing and reinserting a JUUL pod resulted in greater PM2.5 concentrations compared to puffing protocols in which the JUUL pod was not removed and reinserted. ECIGs should be examined and evaluated based on ECIG users' real-world behaviors.

Speciation of chromium via laser-induced breakdown spectroscopy of ion exchange polymer membranes.

A new method for the speciation of ng/mL concentrations of Cr(III) and Cr(VI) solutions with analysis by laser-induced breakdown spectroscopy (LIBS) is reported. Speciation is achieved by pre-concentration of the chromium onto commercially available cation exchange polymer membranes. Chromium(III) is removed directly by cation exchange; chromium(VI) in the filtrate is reduced to Cr(III) and concentrated onto a second cation exchange membrane, affording independent measurement of both species. Large volumes of waters containing Cr(III) and Cr(VI) can be concentrated onto the membranes and directly analyzed by laser-induced breakdown spectroscopy. The estimated limit of detection corresponds to 500 ng of Cr on the membrane: if a solution volume of 1 L is used, then the detection limit corresponds to a solution concentration of 0.5 ng/mL. Excellent separation of the chromium species is attained. Results show that overall method efficiencies range from 94-116% and are independent of the matrix. The influence of pH has been measured, and although Cr(VI) converts to Cr(III) in acidic solutions, the total Cr recoveries are not appreciably influenced by pH over the range of natural waters (4 to 9). In addition, speciation was performed in the presence of a number of different cations and showed that the method is robust in many different and complex matrices.

Resonance-enhanced multiphoton ionization for real-time monitoring of trichloroethylene formed by degradation of tetrachloroethylene using zero-valent zinc.

Resonance-enhanced multiphoton ionization (REMPI) is investigated as a potential technique for real-time monitoring of selected volatile organochloride compounds (VOCs). In a proof-of-concept experiment, the progress of the reductive-degradation of tetrachloroethylene (PCE) to trichloroethylene (TCE) by zero-valent zinc was monitored by REMPI measurements performed in the headspace above the PCE solution. Two-photon resonant REMPI spectra of TCE and PCE were recorded over the wavelength range 305-320 nm. The concentrations of PCE and TCE in the headspace were monitored by measurement of the ionization signal with 315.64- and 310.48-nm excitation for PCE and TCE, respectively. Calibration curves yielded a linear range of more than 2 orders of magnitude for both compounds. The REMPI headspace results agreed well with the solution-phase results from gas chromatography analysis, which was used for independent verification of the progress of the reaction.

Population consequences of fipronil and degradates to copepods at field concentrations: an integration of life cycle testing with leslie matrix population modeling.

The predominant data used in ecological risk assessment today are individual-based rather than population-based; yet environmental policies are usually designed to protect populations of threatened species or communities. Most current methods in ecotoxicology are limited by largely logistic/ technology-driven requirements that yield data for a relatively small number of test species and end points that focus on acute lethality or sublethal nonproduction-based parameters (e.g., biomarkers, mutagenesis, genetic change, physiological condition). A contrasting example is presented here showing the predictive ability of meiobenthos-based full life cycle toxicity testing to extrapolate multi-generational effects of chemicals on variables of import to population growth and maintenance. Less than 24-h-old larvae of a meiobenthic copepod were reared individually in 96-well microplate exposures to parent and degradates of the phenylpyrazole insecticide fipronil. Survival, development rates, sex ratio change, fertility, fecundity, and hatching success were tracked daily for 32 d through mating and production of three broods in spiked seawater. These data were then inserted in a Leslie (Lefkovitch) matrix stage-based population growth model to predict relative rates of population increase (lambda) and changes in net population growth with time and toxicant concentration. Field-reported test concentrations produced strong reproductive (52-88%) and net production (40-80%) depressions for parent (at 0.25 and 0.5 microg/L), desthionyl (0.25 and 0.5 microg/L), and sulfide (0.15 microg/L) moieties as compared to controls. Spiked sediment exposures of 65-300 ng of fipronil/g of dry sediment yielded significantly reduced production rates per female that were 67-50% of control production. The consistent reproductively linked impacts of fipronil and its degradation products at the population maintenance levels suggest risks to sediment-dwelling crustaceans at concentrations well below noneffects for most aquatic test species based on risk assessment data from primarily acute and sub-life cycle toxicity tests.

Dual-pulse laser-induced breakdown spectroscopy with combinations of femtosecond and nanosecond laser pulses.

Nanosecond and femtosecond laser pulses were combined in an orthogonal preablation spark dual-pulse laser-induced breakdown spectroscopy (LIBS) configuration. Even without full optimization of interpulse alignment, ablation focus, large signal, signal-to-noise ratio, and signal-to-background ratio enhancements were observed for both copper and aluminum targets. Despite the preliminary nature of this study, these results have significant implications in the attempt to explain the sources of dual-pulse LIBS enhancements.