ABSTRACT
This study investigates the solid-state charge transport properties of the oxidized forms of dioxythiophene-based alternating copolymers consisting of an oligoether-functionalized 3,4-propylenedioxythiophene (ProDOT) copolymerized with different aryl groups, dimethyl ProDOT (DMP), 3,4-ethylenedioxythiophene (EDOT), and 3,4-phenylenedioxythiophene (PheDOT), respectively, to yield copolymers P(OE3)-D, P(OE3)-E, and P(OE3)-Ph. At a dopant concentration of 5 mM FeTos3, the electrical conductivities of these copolymers vary significantly (ranging between 9 and 195 S cm-1) with the EDOT copolymer, P(OE3)-E, achieving the highest electrical conductivity. UV-vis-NIR and X-ray spectroscopies show differences in both susceptibility to oxidative doping and extent of oxidation for the P(OE3) series, with P(OE3)-E being the most doped. Wide-angle X-ray scattering measurements indicate that P(OE3)-E generally demonstrates the lowest paracrystallinity values in the series, as well as relatively small π-π stacking distances. The significant (i.e., order of magnitude) increase in electrical conductivity of doped P(OE3)-E films versus doped P(OE3)-D or P(OE3)-Ph films can therefore be attributed to P(OE3)-E exhibiting both the highest carrier ratios in the P(OE3) series, along with good π-π overlap and local ordering (low paracrystallinity values). Furthermore, these trends in the extent of doping and paracrystallinity are consistent with the reduced Fermi energy level and transport function prefactor parameters calculated using the semilocalized transport (SLoT) model. Observed differences in carrier ratios at the transport edge (ct) and reduced Fermi energies [η(c)] suggest a broader electronic band (better overlap and more delocalization) for the EDOT-incorporating P(OE3)-E polymer relative to P(OE3)-D and P(OE3)-Ph. Ultimately, we rationalize improvements in electrical conductivity due to microstructural and doping enhancements caused by EDOT incorporation, a structure-property relationship worth considering in the future design of highly electrically conductive systems.
ABSTRACT
Chemically doped poly[2,5-bis(3-alkylthiophen-2-yl)thieno[3,2-b]thiophene] (PBTTT) shows promise for many organic electronic applications, but rationalizing its charge transport properties is challenging because conjugated polymers are inhomogeneous, with convoluted optical and solid-state transport properties. Herein, we use the semilocalized transport (SLoT) model to quantify how the charge transport properties of PBTTT change as a function of iron(III) chloride (FeCl3) doping level. We use the SLoT model to calculate fundamental transport parameters, including the carrier density needed for metal-like electrical conductivities and the position of the Fermi energy level with respect to the transport edge. We then contextualize these parameters with other polymer-dopant systems and previous PBTTT reports. Additionally, we use grazing incidence wide-angle X-ray scattering and spectroscopic ellipsometry techniques to better characterize inhomogeneity in PBTTT. Our analyses indicate that PBTTT obtains high electrical conductivities due to its quickly rising reduced Fermi energy level, and this rise is afforded by its locally high carrier densities in highly ordered microdomains. Ultimately, this report sets a benchmark for comparing transport properties across polymer-dopant-processing systems.
ABSTRACT
Synthetic efforts have delivered a library of organic mixed ionic-electronic conductors (OMIECs) with high performance in electrochemical transistors. The most promising materials are redox-active conjugated polymers with hydrophilic side chains that reach high transconductances in aqueous electrolytes due to volumetric electrochemical charging. Current approaches to improve transconductance and device stability focus mostly on materials chemistry including backbone and side chain design. However, other parameters such as the initial microstructure and microstructural rearrangements during electrochemical charging are equally important and are influenced by backbone and side chain chemistry. In this study, we employ a polymer system to investigate the fundamental electrochemical charging mechanisms of OMIECs. We couple in situ electronic charge transport measurements and spectroelectrochemistry with ex situ X-ray scattering electrochemical charging experiments and find that polymer chains planarize during electrochemical charging. Our work shows that the most effective conductivity modulation is related to electrochemical accessibility of well-ordered, interconnected aggregates that host high mobility electronic charge carriers. Electrochemical stress cycling induces microstructural changes, but we find that these aggregates can largely maintain order, providing insights on the structural stability and reversibility of electrochemical charging in these systems. This work shows the importance of material design for creating OMIECs that undergo structural rearrangements to accommodate ions and electronic charge carriers during which percolating networks are formed for efficient electronic charge transport.
ABSTRACT
Preceramic polymers (PCPs) are a group of specialty macromolecules that serve as precursors for generating inorganics, including ceramic carbides, nitrides, and borides. PCPs represent interesting synthetic challenges for chemists due to the elements incorporated into their structure. This group of polymers is also of interest to engineers as PCPs enable the processing of polymer-derived ceramic products including high-performance ceramic fibers and composites. These finished ceramic materials are of growing significance for applications that experience extreme operating environments (e.g., aerospace propulsion and high-speed atmospheric flight). This Review provides an overview of advances in the synthesis and postpolymerization modification of macromolecules forming nonoxide ceramics. These PCPs include polycarbosilanes, polysilanes, polysilazanes, and precursors for ultrahigh-temperature ceramics. Following our review of PCP synthetic chemistry, we provide examples of the application and processing of these polymers, including their use in fiber spinning, composite fabrication, and additive manufacturing. The principal objective of this Review is to provide a resource that bridges the disciplines of synthetic chemistry and ceramic engineering while providing both insights and inspiration for future collaborative work that will ultimately drive the PCP field forward.
ABSTRACT
Herein, a route to produce highly electrically conductive doped hydroxymethyl functionalized poly(3,4-ethylenedioxythiophene) (PEDOT) films, termed PEDOT(OH) with metal-like charge transport properties using a fully solution processable precursor polymer is reported. This is achieved via an ester-functionalized PEDOT derivative [PEDOT(EHE)] that is soluble in a range of solvents with excellent film-forming ability. PEDOT(EHE) demonstrates moderate electrical conductivities of 20-60â S cm-1 and hopping-like (i.e., thermally activated) transport when doped with ferric tosylate (FeTos3 ). Upon basic hydrolysis of PEDOT(EHE) films, the electrically insulative side chains are cleaved and washed from the polymer film, leaving a densified film of PEDOT(OH). These films, when optimally doped, reach electrical conductivities of ≈1200â S cm-1 and demonstrate metal-like (i.e., thermally deactivated and band-like) transport properties and high stability at comparable doping levels.
ABSTRACT
This study investigates the charge-transport properties of poly(3-hexylthiophene-2,5-diyl) (P3HT) and poly(ProDOT-alt-biEDOT) (PE2) films doped with a set of iron(III)-based dopants and as a function of dopant concentration. X-ray photoelectron spectroscopy measurements show that doping P3HT with 12 mM iron(III) solutions leads to similar extents of oxidation, independent of the dopant anion; however, the electrical conductivities and Seebeck coefficients vary significantly (5 S cm-1 and + 82 µV K-1 with tosylate and 56 S cm-1 and +31 µV K-1 with perchlorate). In contrast, PE2 thermoelectric transport properties vary less with respect to the iron(III) anion chemistry, which is attributed to PE2 having a lower onset of oxidation than P3HT. Consequentially, PE2 doped with 12 mM iron(III) perchlorate obtained an electrical conductivity of 315 S cm-1 and a Seebeck coefficient of + 7 µV K-1. Modeling these thermoelectric properties with the semilocalized transport (SLoT) model suggests that tosylate-doped P3HT remains mostly in the localized transport regime, attributed to more disorder in the microstructure. In contrast perchlorate-doped P3HT and PE2 films exhibited thermally deactivated electrical conductivities and metal-like transport at high doping levels over limited temperature ranges. Finally, the SLoT model suggests that PE2 has the potential to be more electrically conductive than P3HT due to PE2's ability to achieve higher extents of oxidation and larger shifts in the reduced Fermi energy levels.
ABSTRACT
The processability and electronic properties of conjugated polymers (CPs) have become increasingly important due to the potential of these materials in redox and solid-state devices for a broad range of applications. To solubilize CPs, side chains are needed, but such side chains reduce the relative fraction of electroactive material in the film, potentially obstructing π-π intermolecular interactions, localizing charge carriers, and compromising desirable optoelectronic properties. To reduce the deleterious effects of side chains, we demonstrate that post-processing side chain removal, exemplified here via ester hydrolysis, significantly increases the electrical conductivity of chemically doped CP films. Beginning with a model system consisting of an ester functionalized ProDOT copolymerized with a dimethylProDOT, we used a variety of methods to assess the changes in polymer film volume and morphology upon hydrolysis and resulting active material densification. Via a combination of electrochemistry, X-ray photoelectron spectroscopy, and charge transport models, we demonstrate that this increase in electrical conductivity is not due to an increase in degree of doping but an increase in charge carrier density and reduction in carrier localization that occurs due to side chain removal. With this improved understanding of side chain hydrolysis, we then apply this method to high-performance ProDOT-alt-EDOTx copolymers. After hydrolysis, these ProDOT-alt-EDOTx copolymers yield exceptional electrical conductivities (â¼700 S/cm), outperforming all previously reported oligoether-/glycol-based CP systems. Ultimately, this methodology advances the ability to solution process highly electrically conductive CP films.
ABSTRACT
The unique electrochemical properties of the conductive polymer poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) make it an attractive material for use in neural tissue engineering applications. However, inadequate mechanical properties, and difficulties in processing and lack of biodegradability have hindered progress in this field. Here, the functionality of PEDOT:PSS for neural tissue engineering is improved by incorporating 3,4-ethylenedioxythiophene (EDOT) oligomers, synthesized using a novel end-capping strategy, into block co-polymers. By exploiting end-functionalized oligoEDOT constructs as macroinitiators for the polymerization of poly(caprolactone), a block co-polymer is produced that is electroactive, processable, and bio-compatible. By combining these properties, electroactive fibrous mats are produced for neuronal culture via solution electrospinning and melt electrospinning writing. Importantly, it is also shown that neurite length and branching of neural stem cells can be enhanced on the materials under electrical stimulation, demonstrating the promise of these scaffolds for neural tissue engineering.
ABSTRACT
This work presents a soluble oligo(ether)-functionalized propylenedioxythiophene (ProDOT)-based copolymer as a versatile platform for a range of high-performance electrochemical devices, including organic electrochemical transistors (OECTs), electrochromic displays, and energy-storage devices. This polymer exhibits dual electroactivity in both aqueous and organic electrolyte systems, redox stability for thousands of redox cycles, and charge-storage capacity exceeding 80 F g-1 . As an electrochrome, this material undergoes full colored-to-colorless optical transitions on rapid time scales (<2 s) and impressive electrochromic contrast (Δ%T > 70%). Incorporation of the polymer into OECTs yields accumulation-mode devices with an ION/OFF current ratio of 105 , high transconductance without post-treatments, as well as competitive hole mobility and volumetric capacitance, making it an attractive candidate for biosensing applications. In addition to being the first ProDOT-based OECT active material reported to date, this is also the first reported OECT material synthesized via direct(hetero)arylation polymerization, which is a highly favorable polymerization method when compared to commonly used Stille cross-coupling. This work provides a demonstration of how a single ProDOT-based polymer, prepared using benign polymerization chemistry and functionalized with highly polar side chains, can be used to access a range of highly desirable properties and performance metrics relevant to electrochemical, optical, and bioelectronic applications.
ABSTRACT
We present a rational approach to fabricating plasmonically active hybrid polymer-metal nanomaterials with electrochemical tunability of the localized surface plasmon resonances (LSPRs) of noble metal nanostructures embedded in an electroactive polymer matrix. The key requirement for being able to significantly modulate the LSPR band position is a close overlap between the refractive index change [Δn(λ)] of a stimuli-responsive polymeric matrix and the intrinsic LSPR bands. For this purpose, gold nanorods with a controlled aspect ratio, synthesized to provide high refractive index sensitivity while maintaining good oxidative stability, were combined with a solution-processable electroactive and electrochromic polymer (ECP): alkoxy-substituted poly(3,4-propylenedioxythiophene) [PProDOT(CH2OEtHx)2]. Spectral characteristics of the ECP, in particular the Δn(λ) variation, were evaluated as the material was switched between oxidized and reduced states. We fabricated ultrathin plasmonic electrochromic hybrid films consisting of gold nanorods and ECP that exhibited a large, stable, and reversible LSPR modulation of up to 25-30 nm with an applied electrical potential. Finite-difference time-domain (FDTD) simulations confirm a good match between the experimentally measured refractive index change in the ECP and the plasmonic response during electrochemical modulations.
ABSTRACT
We have designed fully soluble ProDOTx-EDOTy copolymers that are electrochemically equivalent to electropolymerized PEDOT without using any surfactants or dispersants. We show that these copolymers can be incorporated as active layers in solution processed thin film supercapacitors to demonstrate capacitance, stability, and voltage similar to the values of those that use electrodeposited PEDOT as the active material with the added advantage of the possibility for large scale, high-throughput processing. These Type I supercapacitors provide exceptional cell voltages (up to 1.6 V), highly symmetrical charge/discharge behavior, promising long-term stability exceeding 50â¯000 charge/discharge cycles, as well as energy (4-18 Wh/kg) and power densities (0.8-3.3 kW/kg) that are comparable to those of electrochemically synthesized analogues.
ABSTRACT
The first example of a solution processable dioxythiophene-alt-dioxyselenophene polymer, ProDOT-EDOS, prepared via direct (hetero)arylation polymerization is reported and its optical and electrochemical properties are compared to the all thiophene analog, ProDOT-EDOT, and other relevant dioxythiophene polymers. By substituting the sulfur atom for a selenium atom on one of the monomers in the repeat unit a significant red-shift of both the neutral (41 nm, 132 meV) and polaronic (106 nm, 126 meV) absorbances results, as well as a 160 mV reduction in the onset of oxidation compared to ProDOT-EDOT. Spray-cast films of the polymer electrochemically switch from a vibrant blue charge neutral state to a color neutral and highly transmissive oxidized state.
ABSTRACT
Metallic triflates M(OTf)(3) (M = Bi, Sc, Yb), immobilized in imidazolium ionic liquids [BMIM][BF(4)], [BMIM][PF(6)] and [BMIM][OTf] are efficient systems for one-pot reactions of propargylic alcohols 1,3-diphenyl-2-propyn-1-ol Ia, 1-methyl-3-phenyl-2-propyn-1-ol Ib, and 2-pentyn-1-ol Ic, with a wide range of arenes bearing activating substituents, under mild conditions. The [BMIM][PF(6)]/B(C(6)F(5))(3) and [BMIM][PF(6)]/TfOH systems were superior in propargylation with Ib and Ic, while reaction of 3-phenyl-2-propyn-1-ol Id with activated aromatics resulted in the formation of diaryl-propanones instead. Propargylation of anisole with Ib under M(OTf)(3) catalysis is highly para selective, but with TfOH or B(C(6)F(5))(3) as catalyst the ortho isomer was also formed. Steric influence of the propargylic moiety on substrate selectivity is reflected in the lack of ortho propargylation for phenol and ethylbenzene by using propargylic alcohol Ia, and notable formation of the ortho isomer employing alcohol Ib. In the later case para selectivity could be increased by running the reaction at r. t. for 10 h. The Bi(OTf)(3)-catalyzed reaction of 1,3-dimethoxybenzene with Ia led to minor formation of dipropargylated derivative, along with the monopropargyl product. Propargylation of the less reactive arenes (mesitylene, ethylbenzene, toluene), using Sc(OTf)(3) as catalyst, led increasingly to the formation of dipropargylic ethers and propargyl ketones, with no ring propargylation product with toluene. Concomitant formation of dipropargylic ether was also observed in Yb(OTf)(3)-catalyzed propargylation of ß-naphthol, whereas propargylation of 2-nitro and 4-nitro-aniline led to N-propargylation. The recycling/reuse of the IL was demonstrated in representative cases with no appreciable decrease in the conversions over 3 cycles. It was also shown that recycled IL could be used to propargylate a different aromatic compound. The efficacy of IL/M(OTf)(3) and IL/TfOH systems for cross-breeding two propargylic alcohols or a propargylic alcohol with a non-propargylic alcohol and/or self-coupling, to form a wide variety of functionalized ethers is also demonstrated.