Impact of Construction Waste Disposal Charging Scheme on work practices at construction sites in Hong Kong.

Waste management in the building industry in Hong Kong has become an important environmental issue. Particularly, an increasing amount of construction and demolition (C&D) waste is being disposed at landfill sites. In order to reduce waste generation and encourage reuse and recycling, the Hong Kong Government has implemented the Construction Waste Disposal Charging Scheme (CWDCS) to levy charges on C&D waste disposal to landfills. In order to provide information on the changes in reducing waste generation practice among construction participants in various work trades, a study was conducted after 3 years of implementation of the CWDCS via a structured questionnaire survey in the building industry in Hong Kong. The study result has revealed changes with work flows of the major trades as well as differentiating the levels of waste reduced. Three building projects in the public and private sectors were selected as case studies to demonstrate the changes in work flows and the reduction of waste achieved. The research findings reveal that a significant reduction of construction waste was achieved at the first 3 years (2006-2008) of CWDCS implementation. However, the reduction cannot be sustained. The major trades have been influenced to a certain extent by the implementation of the CWDCS. Slight improvement in waste management practices was observed, but reduction of construction waste in the wet-finishing and dry-finishing trades has undergone little improvement. Implementation of the CWDCS has not yet motivated subcontractors to change their methods of construction so as to reduce C&D waste.

Environmental management system vs green specifications: how do they complement each other in the construction industry?

Environmental Management System (EMS) has been one of the important tools for sustainable construction for around two decades. However, many issues concerning sustainable development have not been properly addressed, and there is a need for the introduction of green specifications to advance green performance in construction through contract management. This paper defines green specifications, identifies the reasons for adopting green specifications and highlights the environmental issues that may not be addressed by solely adopting EMS. It also presents the results of a recent survey of practitioners concerning their opinions towards green specifications and possible impacts arising from their adoption. From the results of the survey, a framework for developing green specifications is deemed valuable for the cities striving for sustainability. Interestingly, the level of acceptable changes brought about by green specifications as perceived by different industry stakeholders is found to be unrelated to whether they were from organizations implementing EMS or not.

Hypoxia-excited neurons in NTS send axonal projections to Kölliker-Fuse/parabrachial complex in dorsolateral pons.

Hypoxic respiratory and cardiovascular responses in mammals are mediated by peripheral chemoreceptor afferents which are relayed centrally via the solitary tract nucleus (NTS) in dorsomedial medulla to other cardiorespiratory-related brainstem regions such as ventrolateral medulla (VLM). Here, we test the hypothesis that peripheral chemoafferents could also be relayed directly to the Kölliker-Fuse/parabrachial complex in dorsolateral pons, an area traditionally thought to subserve pneumotaxic and cardiovascular regulation. Experiments were performed on adult Sprague-Dawley rats. Brainstem neurons with axons projecting to the dorsolateral pons were retrogradely labeled by microinjection with choleras toxin subunit B (CTB). Neurons involved in peripheral chemoreflex were identified by hypoxia-induced c-Fos expression. We found that double-labeled neurons (i.e. immunopositive to both CTB and c-Fos) were localized mostly in the commissural and medial subnuclei of NTS and to a lesser extent in the ventrolateral NTS subnucleus, VLM and ventrolateral pontine A5 region. Extracellular recordings from the commissural and medial NTS subnuclei revealed that some hypoxia-excited NTS neurons could be antidromically activated by electrical stimulations at the dorsolateral pons. These findings demonstrate that hypoxia-activated afferent inputs are relayed to the Kölliker-Fuse/parabrachial complex directly via the commissural and medial NTS and indirectly via the ventrolateral NTS subnucleus, VLM and A5 region. These pontine-projecting peripheral chemoafferent inputs may play an important role in the modulation of cardiorespiratory regulation by dorsolateral pons.

Factors affecting the implementation of green specifications in construction.

Green specifications constitute one of the important elements in green construction. New sustainability requirements and changing priorities in construction management have spurred the emerging green specifications to a faster pace of development. A cross-sectional survey has been conducted in Hong Kong in 2007 to identify principal factors leading to the success of preparing green specifications. Based on extensive construction management literature, 20 variables concerning sustainable construction were summarized. Using the Mann-Whitney U-test, the subtle differences between stakeholders in specifying construction work have been detected even with the high consistency of the responses among the groups. Moreover, five independent factors for successful specification of green construction have been categorized by factor analysis. They are related to (1) green technology and techniques, (2) reliability and quality of specification, (3) leadership and responsibility, (4) stakeholder involvement, and (5) guide and benchmarking systems. Whilst the first and fourth factors are generally more important, different stakeholder groups have different emphases. The results of the survey have been validated against established principles.

Cultural shift towards sustainability in the construction industry of Hong Kong.

Sustainable development is forward-looking; it is a continuous mission for future developments of human society. A genuinely sustainable society is one that initiates developments in sustainable ways. The development of a genuinely sustainable society is supported by its citizens who think and act according to a recognized code of conduct - the sustainable culture. Similar to other forms of culture, sustainable culture of a society is not static, but changes over time. The changes found in a sustainable culture are reflections of the status of sustainability in a society and these changes should be measured from time to time. The resulting measurement gives very important information for decision-makers, in the government and in the private sector, to examine the magnitude of changes that have taken place in a given period of time. The results will also enable them to review and adjust policies in order to better accommodate changes according to the trends of society. This paper provides a method - the T-model, to investigate and measure the extent of change of sustainable culture through two extensive surveys among participants of the construction industry of Hong Kong. The change in sustainable culture is reflected by the change in attitude and practice among construction participants, this can be found in their performance in project development, design and construction operations. The data of these changes are collected and converted to numerical scores. The T-model synthesized these scores and revealed the change of sustainable culture within the specific study time frame.

Properties of lightweight aggregate concrete prepared with PVC granules derived from scraped PVC pipes.

This paper aims to investigate the fresh and hardened properties of lightweight aggregate concretes that are prepared with the use of recycled plastic waste sourced from scraped PVC pipes to replace river sand as fine aggregates. A number of laboratory prepared concrete mixes were tested, in which river sand was partially replaced by PVC plastic waste granules in percentages of 0%, 5%, 15%, 30% and 45% by volume. Two major findings are identified. The positive side shows that the concrete prepared with a partial replacement by PVC was lighter (lower density), was more ductile (greater Poisson's ratios and reduced modulus of elasticity), and had lower drying shrinkage and higher resistance to chloride ion penetration. The negative side reveals that the workability, compressive strength and tensile splitting strength of the concretes were reduced. The results gathered would form a part of useful information for recycling PVC plastic waste in lightweight concrete mixes.

Influences of chemical activators on incinerator bottom ash.

This research has applied different chemical activators to mechanically and thermally treated fine fraction (<14 mm) of incinerator bottom ash (IBA), in order to investigate the influences of chemical activators on this new pozzolanic material. IBA has been milled and thermally treated at 800 degrees C (TIBA). The TIBA produced was blended with Ca(OH)(2) and evaluated for setting time, reactivity and compressive strength after the addition of 0.0565 mole of Na(2)SO(4), K(2)SO(4), Na(2)CO(3), K(2)CO(3), NaOH, KOH and CaCl(2) into 100g of binder (TIBA+Ca(OH)(2)). The microstructures of activated IBA and hydrated samples have been characterized by X-ray diffraction (XRD) and thermogravimetry (TG) analysis. Thermal treatment is found to produce gehlenite (Ca(2)Al(2)SiO(7)), wollastonite (CaSiO(3)) and mayenite (Ca(12)Al(14)O(33)) phases. The thermally treated IBA samples are significantly more reactive than the milled IBA. The addition of Na(2)CO(3) can increase the compressive strength and calcium hydroxide consumption at 28-day curing ages. However, the addition of Na(2)SO(4), K(2)SO(4), K(2)CO(3), NaOH and KOH reduces the strength and hydration reaction. Moreover, these chemicals produce more porous samples due to increased generation of hydrogen gas. The addition of CaCl(2) has a negative effect on the hydration of TIBA samples. Calcium aluminium oxide carbonate sulphide hydrate (Ca(4)Al(2)O(6)(CO(3))(0.67)(SO(3))(0.33)(H(2)O)(11)) is the main hydration product in the samples with activated IBA, except for the sample containing CaCl(2).

Quantifying the waste reduction potential of using prefabrication in building construction in Hong Kong.

As Hong Kong is a compact city with limited available land and high land prices, the construction of high-rise buildings is prevalent. The construction industry produces a significant amount of building waste. In 2005, about 21.5 million tonnes of construction waste were generated, of which 11% was disposed of in landfills and 89% in public filling areas. At the present rate, Hong Kong will run out of both public filling areas and landfill space within the next decade. The government is taking action to tackle the problem, such as by introducing a construction waste landfill charge, and promoting prefabrication to reduce on-site waste generation. This paper reports an ongoing study on the use of prefabrication in buildings and its impact on waste reduction in Hong Kong. A questionnaire survey was administered to experienced professionals, and case studies of recently completed building projects were conducted. The results revealed that construction waste reduction is one of the major benefits when using prefabrication compared with conventional construction. The average wastage reduction level was about 52%. This implies that a wider use of prefabrication could considerably reduce construction waste generation in Hong Kong and alleviate the burdens associated with its management.

Characterization of alkali-activated thermally treated incinerator bottom ash.

The fine fraction (<14 mm) of incinerator bottom ash (IBA) obtained from a UK energy from waste plant has been milled and thermally treated at 600, 700, 800 and 880 degrees C. Treated materials have been activated with Ca(OH)(2) (10 wt%) and the setting times and compressive strengths at different curing times measured. In addition to decomposition of CaCO(3) to CaO, thermal treatment increases the content of gehlenite (Ca(2)Al(2)SiO(7)), wollastonite (CaSiO(3)) and mayenite (Ca(12)Al(14)O(33)). Thermally treated samples were significantly more reactive than milled IBA and heating to 700 degrees C produced a material which rapidly set. Silica, gehlenite and wollastonite were the main crystalline phases present in hydrated samples and a mixed sulphate-carbonate AFm-type phase (Ca(4)Al(2)O(6)(CO(3))(0.67)(SO(3))(0.33).11H(2)O) formed. Significant volumes of gas were generated during curing and this produced a macro-porous microstructure that limited strength to 2.8 MPa. The new materials may have potential for use as controlled low-strength materials.

The role of immunohistochemistry for smooth-muscle actin, p63, CD10 and cytokeratin 14 in the differential diagnosis of papillary lesions of the breast.

BACKGROUND: Histological differentiation of mammary papillary lesions can be difficult. The evaluation of myoepithelial cells can be helpful, with benign papilloma showing a continuous myoepithelial cell layer, which becomes attenuated or absent in malignant papillary lesions. METHODS: A large series of 100 papillomas (28 papillomas with florid epithelial hyperplasia) and 68 papillary carcinomas (9 invasive, 44 in situ, and 15 ductal carcinomas in situ (DCIS) involving papillomas) of the breast were stained for myoepithelial cells by immunohistochemistry using antibodies to smooth-muscle actin (SMA), p63, CD10 and cytokeratin (CK) 14. RESULTS: In the papillomas, using these four antibodies, myoepithelial cells were positive in 88%, 99%, 91% and 95% of cases, respectively, with SMA showing marked stromal component cell staining and CD10 showing epithelial and stromal staining. CK14 also showed epithelial staining in 71% of papillomas and 96% of papillomas with florid epithelial hyperplasia. In the papillary carcinomas, 36 (53%) cases showed staining of myoepithelial cells that were scattered, discontinuous and diminished in number and the remaining 32 (47%) cases did not show myoepithelial cells. Invasive papillary carcinoma has the lowest proportion (33%) with myoepithelial cells, and DCIS involving papillomas had the highest proportion (87%). CONCLUSIONS: p63 had the highest sensitivity and did not cross-react with stromal cells and only rarely with epithelial cells. CK14 has the added ability to distinguish between florid epithelial hyperplasia involving papilloma and DCIS involving papillomas. CK14 and p63 may be used as an adjunct in assessing difficult papillary lesions of the breast.

Investigation into the stabilization/solidification performance of Portland cement through cement clinker phases.

This research studied the influence of individual heavy metal on the hydration reactions of major cement clinker phases in order to investigate the performance of cement based stabilization/solidification (S/S) system. Tricalcium silicate (C3S) and tricalcium aluminate (C3A) had been mixed with individual heavy metal hydroxide including Zn(OH)2, Pb(OH)2 and Cu(OH)2, respectively. The influences of these heavy metal hydroxides on the hydration of C3S and C3A have been characterized by X-ray diffraction (XRD) and differential scanning calorimetry-thermogravimetry (DSC-TG). A mixture of Zn(OH)2, Pb(OH)2 and Cu(OH)2 was blended with Portland cement (PC) and evaluated through compressive strength and dynamic leach test. XRD and DSC-TG data show that all the heavy metal hydroxides (Zn(OH)2, Pb(OH)2 and Cu(OH)2) have detrimental effects on the hydration of C3A, but only Zn(OH)2 does to the C3S at early curing ages which can completely inhibit the hydration of C3S due to the formation of CaO(Zn(OH)2).2H2O. Cu6Al2O8CO(3).12H2O, Pb2Al4O4(CO3)(4).7H2O and Zn6Al2O8CO(3).12H2O are formed in all the samples containing C3A in the presence of metal hydroxides. After adding CaSO4 into C3A, the detrimental effect of heavy metals increases due to the coating effect of both calcium aluminate sulphates and heavy metal aluminate carbonates. The influence of heavy metal hydroxide on the hydration of C3S and C3A can be used to predict the S/S performance of Portland cement.

Use of flue gas desulphurisation (FGD) waste and rejected fly ash in waste stabilization/solidification systems.

Stabilization/solidification (S/S) processes have been used as the final treatment step for hazardous wastes prior to land disposal. Fly ash is a by-product of coal-fired power generation; a significant proportion of this material is low-grade, reject material (rFA) that is unsuitable as a cement replacement due to its high carbon content and large particle size (>45 microm). Flue gas desulphurization (FGD) sludge is a by-product from the air pollution control systems used in coal-fired power plants. The objective of this work was to investigate the performance of S/S waste binder systems containing these two waste materials (rFA and FGD). Strength tests show that cement-based waste forms with rFA and FGD replacement were suitable for disposal in landfills. The addition of an appropriate quantity of Ca(OH)2 and FGD reduces the deleterious effect of heavy metals on strength development. Results of TCLP testing and the progressive TCLP test show that cement-rFA-Ca(OH)2 systems with a range of FGD additions can form an effective S/S binder. The Leachability Index indicates that cement-based waste forms with rFA replacement were effective in reducing the mobility of heavy metals.

Transfer mechanisms of contaminants in cement-based stabilized/solidified wastes.

Stabilization/solidification (S/S) processes are routinely used for the final treatment of hazardous wastes prior to land disposal. Cement-based binder systems with partial replacement of cement by pulverized fuel ash (PFA) are common. In order to predict the long-term leaching characteristics of S/S wastes, it is important to understand the leaching mechanism. This paper presents experimental results from a study that has investigated the leaching behaviour of contaminants from cement-based S/S waste forms. A novel radial leach test (RLT) has been used to study the migration of heavy metals. The results show that contaminants migrate from the inner core of the S/S waste during leaching to the sample surface and accumulate near the edge of the S/S waste. The degree of accumulation is related to the contaminant species and the Ca(OH)2 content.

Circadian rhythms of spectral components of heart rate variability.

Circadian rhythms of heart rate variability have been widely studied in recent years. However, most previous reports described such rhythms in terms of normalized units of the low- and high-frequency (LF and HF) spectral components. In this study, we analyzed circadian rhythms of spectral components in absolute units and found unexpected results in normal subjects as well as coronary heart disease (CHD) and congestive heart failure (CHF) patient groups. The results indicate that the notion of sympathovagal balance needs to be re-evaluated.

CD44s is useful in the differentiation of benign and malignant papillary lesions of the breast.

BACKGROUND/AIMS: CD44s, the standard form of CD44, has been shown to be downregulated during malignant transformation of breast cancers. It has also been reported recently to be a useful marker in differentiating between benign and malignant papillary lesions of the breast, with high expression in the former. CD44s expression in benign and malignant papillary lesions was evaluated. METHODS: CD44s expression was assessed by immunohistochemistry in 101 benign papillomas and 59 papillary carcinomas (seven invasive papillary carcinomas, 41 papillary ductal carcinomas in situ, and 11 ductal carcinomas involving papillomas). RESULTS: Patients' age and tumour size were significantly different between the papilloma and papillary carcinoma groups (p < 0.0001). CD44s showed positive staining in 45 papillomas (45%) and five papillary carcinomas (8%), and the difference was significant (p < 0.0001). The myoepithelial cells, when present, were also positive for CD44s in both groups, with no observable differences. Using CD44s positive staining to differentiate between benign and malignant papillary lesions gives a sensitivity, specificity, and accuracy of 45%, 92%, and 62%, respectively. CONCLUSIONS: CD44s may be useful as an adjunct in the evaluation of morphologically problematic cases of papillary lesion of the breast.

Neural plasticity of respiratory control system: modeling perspectives.

Classical models of respiratory control assume a hardwired system architecture with reflex regulation of respiratory rhythm and total ventilation. Recent experimental studies, however, reveal a much more pliable architecture with varying forms of neural plasticity in the afferent and efferent pathways. Here, mathematical models of several types of neural plasticity are proposed and their computational roles in respiratory neural processing are discussed.

Nonassociative learning in expiratory inhibition of inspiratory motor output: an experimental and modeling study.

The present study is to characterize the habituation and re-sensitization in the inspiratory inhibition produced by the Bötzinger Complex (BOt.C) and the modulation effects of raphe pallidus (RP) and locus coeruleus (LC). Experiments were done on urethane anaesthetized, vagotomized, paralyzed and artificially ventilated rabbits. Electrical stimulation of the BOt.C (25 ..A, 80 Hz, 15 sec) caused inspiratory inhibition that became gradually adapted with the continuation of the stimulation. At the offset of this stimulation, the phrenic discharge showed temporary rebound increase in amplitude. The adaptation-rebound response pattern resembled a neural differentiator. Pre-stimulation of the RP or LC (50 ..A, 80 Hz, 10 sec) facilitated the adaptation of BOt.C's inspiratory inhibition and the post-stimulus rebound. The results indicate the existence of nonassociative learning (habituation and re-sensitization) in the inspiratory inhibition circuit and the modulation of this nonassociative learning by RP and LC.