A silicone-based support material eliminates interfacial instabilities in 3D silicone printing.

Among the diverse areas of 3D printing, high-quality silicone printing is one of the least available and most restrictive. However, silicone-based components are integral to numerous advanced technologies and everyday consumer products. We developed a silicone 3D printing technique that produces precise, accurate, strong, and functional structures made from several commercially available silicone formulations. To achieve this level of performance, we developed a support material made from a silicone oil emulsion. This material exhibits negligible interfacial tension against silicone-based inks, eliminating the disruptive forces that often drive printed silicone features to deform and break apart. The versatility of this approach enables the use of established silicone formulations in fabricating complex structures and features as small as 8 micrometers in diameter.

Modeling bystander effects that cause growth delay of breast cancer xenografts in bone marrow of mice treated with radium-223.

RATIONALE: The role of radiation-induced bystander effects in cancer therapy with alpha-particle emitting radiopharmaceuticals remains unclear. With renewed interest in using alpha-particle emitters to sterilize disseminated tumor cells, micrometastases, and tumors, a better understanding of the direct effects of alpha particles and the contribution of the bystander responses they induce is needed to refine dosimetric models that help predict clinical benefit. Accordingly, this work models and quantifies the relative importance of direct effects (DE) and bystander effects (BE) in the growth delay of human breast cancer xenografts observed previously in the tibiae of mice treated with 223RaCl2. METHODS: A computational model of MDA-MB-231 and MCF-7 human breast cancer xenografts in the tibial bone marrow of mice administered 223RaCl2 was created. A Monte Carlo radiation transport simulation was performed to assess individual cell absorbed doses. The responses of the breast cancer cells to direct alpha particle irradiation and gamma irradiation were needed as input data for the model and were determined experimentally using a colony-forming assay and compared to the responses of preosteoblast MC3T3-E1 and osteocyte-like MLO-Y4 bone cells. Using these data, a scheme was devised to simulate the dynamic proliferation of the tumors in vivo, including DE and BE propagated from the irradiated cells. The parameters of the scheme were estimated semi-empirically to fit experimental tumor growth. RESULTS: A robust BE component, in addition to a much smaller DE component, was required to simulate the in vivo tumor proliferation. We also found that the relative biological effectiveness (RBE) for cell killing by alpha particle radiation was greater for the bone cells than the tumor cells. CONCLUSION: This modeling study demonstrates that DE of radiation alone cannot explain experimental observations of 223RaCl2-induced growth delay of human breast cancer xenografts. Furthermore, while the mechanisms underlying BE remain unclear, the addition of a BE component to the model is necessary to provide an accurate prediction of the growth delay. More complex models are needed to further comprehend the extent and complexity of 223RaCl2-induced BE.

CXCR1- or CXCR2-modified CAR T cells co-opt IL-8 for maximal antitumor efficacy in solid tumors.

Chimeric antigen receptor (CAR) T-cell therapy targeting solid tumors has stagnated as a result of tumor heterogeneity, immunosuppressive microenvironments, and inadequate intratumoral T cell trafficking and persistence. Early (≤3 days) intratumoral presentation of CAR T cells post-treatment is a superior predictor of survival than peripheral persistence. Therefore, we have co-opted IL-8 release from tumors to enhance intratumoral T-cell trafficking through a CAR design for maximal antitumor activity in solid tumors. Here, we demonstrate that IL-8 receptor, CXCR1 or CXCR2, modified CARs markedly enhance migration and persistence of T cells in the tumor, which induce complete tumor regression and long-lasting immunologic memory in pre-clinical models of aggressive tumors such as glioblastoma, ovarian and pancreatic cancer.

Three-Dimensional Printing for Construction of Tissue-Equivalent Anthropomorphic Phantoms and Determination of Conceptus Dose.

OBJECTIVE: The purpose of this study was to develop a road map for rapid construction of anthropomorphic phantoms from computational human phantoms for use in diagnostic imaging dosimetry studies. These phantoms are ideal for performing pregnant-patient dosimetry because the phantoms imitate the size and attenuation properties of an average-sized pregnant woman for multiple gestational periods. MATERIALS AND METHODS: The method was derived from methods and materials previously described but adapted for 3D printing technology. A 3D printer was used to transform computational models into a physical duplicate with small losses in spatial accuracy and to generate tissue-equivalent materials characterized for diagnostic energy x-rays. A series of pregnant abdomens were selected as prototypes because of their large size and complex modeling. The process involved the following steps: segmentation of anatomy used for modeling; transformation of the computational model into a printing file format; preparation, characterization, and introduction of phantom materials; and model removal and phantom assembly. RESULTS: The density of the homogenized soft tissue-equivalent substitute was optimized by combining 9.0% by weight of urethane filler powder and 91.0% urethane polymer, which resulted in a mean density of 1.041 g/cm3 measured over 20 samples. Density varied among all of the samples by 0.0026 g/cm3. The total variation in density was 0.00261 g/cm3. The half-value layer of the bone material was measured to be 1.7 mm of bone material at 120 kVp and when simulated by use of the density of the bone tissue-equivalent substitute (1.60 g/cm3) was determined to be 1.61 mm of bone tissue. For dosimetry purposes the phantom provided excellent results for evaluating a site's protocol based on scan range. CONCLUSION: The 3D printing technology is applicable to the fabrication of phantoms used for performing dosimetry. The tissue-equivalent materials used to substitute for the soft tissue were developed to be highly adaptable for optimization based on the dosimetry application. Use of this method resulted in more automated phantom construction with decreased construction time and increased out-of-slice spatial resolution of the phantoms.

An image-based skeletal dosimetry model for the ICRP reference adult female-internal electron sources.

An image-based skeletal dosimetry model for internal electron sources was created for the ICRP-defined reference adult female. Many previous skeletal dosimetry models, which are still employed in commonly used internal dosimetry software, do not properly account for electron escape from trabecular spongiosa, electron cross-fire from cortical bone, and the impact of marrow cellularity on active marrow self-irradiation. Furthermore, these existing models do not employ the current ICRP definition of a 50 µm bone endosteum (or shallow marrow). Each of these limitations was addressed in the present study. Electron transport was completed to determine specific absorbed fractions to both active and shallow marrow of the skeletal regions of the University of Florida reference adult female. The skeletal macrostructure and microstructure were modeled separately. The bone macrostructure was based on the whole-body hybrid computational phantom of the UF series of reference models, while the bone microstructure was derived from microCT images of skeletal region samples taken from a 45 years-old female cadaver. The active and shallow marrow are typically adopted as surrogate tissue regions for the hematopoietic stem cells and osteoprogenitor cells, respectively. Source tissues included active marrow, inactive marrow, trabecular bone volume, trabecular bone surfaces, cortical bone volume, and cortical bone surfaces. Marrow cellularity was varied from 10 to 100 percent for active marrow self-irradiation. All other sources were run at the defined ICRP Publication 70 cellularity for each bone site. A total of 33 discrete electron energies, ranging from 1 keV to 10 MeV, were either simulated or analytically modeled. The method of combining skeletal macrostructure and microstructure absorbed fractions assessed using MCNPX electron transport was found to yield results similar to those determined with the PIRT model applied to the UF adult male skeletal dosimetry model. Calculated skeletal averaged absorbed fractions for each source-target combination were found to follow similar trends of more recent dosimetry models (image-based models) but did not follow results from skeletal models based upon assumptions of an infinite expanse of trabecular spongiosa.

Mixed reality ventriculostomy simulation: experience in neurosurgical residency.

BACKGROUND: Medicine and surgery are turning toward simulation to improve on limited patient interaction during residency training. Many simulators today use virtual reality with augmented haptic feedback with little to no physical elements. In a collaborative effort, the University of Florida Department of Neurosurgery and the Center for Safety, Simulation & Advanced Learning Technologies created a novel "mixed" physical and virtual simulator to mimic the ventriculostomy procedure. The simulator contains all the physical components encountered for the procedure with superimposed 3-D virtual elements for the neuroanatomical structures. OBJECTIVE: To introduce the ventriculostomy simulator and its validation as a necessary training tool in neurosurgical residency. METHODS: We tested the simulator in more than 260 residents. An algorithm combining time and accuracy was used to grade performance. Voluntary postperformance surveys were used to evaluate the experience. RESULTS: Results demonstrate that more experienced residents have statistically significant better scores and completed the procedure in less time than inexperienced residents. Survey results revealed that most residents agreed that practice on the simulator would help with future ventriculostomies. CONCLUSION: This mixed reality simulator provides a real-life experience, and will be an instrumental tool in training the next generation of neurosurgeons. We have now implemented a standard where incoming residents must prove efficiency and skill on the simulator before their first interaction with a patient.

Mixed-reality simulation for neurosurgical procedures.

BACKGROUND: Surgical education is moving rapidly to the use of simulation for technical training of residents and maintenance or upgrading of surgical skills in clinical practice. To optimize the learning exercise, it is essential that both visual and haptic cues are presented to best present a real-world experience. Many systems attempt to achieve this goal through a total virtual interface. OBJECTIVE: To demonstrate that the most critical aspect in optimizing a simulation experience is to provide the visual and haptic cues, allowing the training to fully mimic the real-world environment. METHODS: Our approach has been to create a mixed-reality system consisting of a physical and a virtual component. A physical model of the head or spine is created with a 3-dimensional printer using deidentified patient data. The model is linked to a virtual radiographic system or an image guidance platform. A variety of surgical challenges can be presented in which the trainee must use the same anatomic and radiographic references required during actual surgical procedures. RESULTS: Using the aforementioned techniques, we have created simulators for ventriculostomy, percutaneous stereotactic lesion procedure for trigeminal neuralgia, and spinal instrumentation. The design and implementation of these platforms are presented. CONCLUSION: The system has provided the residents an opportunity to understand and appreciate the complex 3-dimensional anatomy of the 3 neurosurgical procedures simulated. The systems have also provided an opportunity to break procedures down into critical segments, allowing the user to concentrate on specific areas of deficiency.

Rapid fabrication of custom patient biopsy guides.

Image guided surgery is currently performed using frame-based as well as frameless approaches. In order to reduce the invasive nature of stereotactic guidance as well as to reduce the cost in both equipment and time required within the operating room we investigated the use of rapid prototyping (RP) technology. In our approach we fabricated custom patient specific face-masks and guides that can be applied to the patient during surgery. These guides provide a stereotactic reference for the accurate placement of surgical tools to a pre-planned target along a pre-planned trajectory. While the use of RP machines has previously been shown to be satisfactory for the accuracy standpoint, one of our design criteria, completing the entire built and introduction into the sterile field in less than 120 minutes, was unobtainable. Our primary problems were the fabrication time and the non-resistance of the built material to high-temperature sterilization. In the current study, we have investigated the use of subtractive rapid prototyping (SRP) machines to perform the same quality of surgical guidance while improving the fabrication time and allowing for choosing materials suitable for sterilization. Because SRP technology does not offer the same flexibility as RP in term of prototype shape and complexity, our software program was adapted to provide new guide designs suitable for SRP fabrication. The biopsy guide was subdivided for a more efficient built with the parts being uniquely assembled to form the final guide. The accuracy of the assembly was then assessed using a modified Brown-Roberts-Wells phantom base that allows measuring the position of a biopsy needle introduced into the guide and comparing it with the actual planned target. These tests showed that 1) SRP machines provide an average accuracy of 0.77 mm with a standard deviation of 0.05 mm (plus or minus one image pixel) and 2) SRP allows for fabrication and sterilization within three and a half hours after diagnostic image acquisition and we are confident that that further improvements can reduce this time to less than two hours. Further tests will determine the accuracy of the positioning of the face mask on the patient's head under an IRB-approved trial judged against actual frame-based and frameless systems.

Development of an intramuscular xenograft model of canine osteosarcoma in mice for evaluation of the effects of radiation therapy.

OBJECTIVE: To develop an IM xenograft model of canine osteosarcoma in mice for the purpose of evaluating effects of radiation therapy on tumors. ANIMALS: 27 athymic nude mice. PROCEDURES: Mice were randomly assigned to 1 of 3 groups of 9 mice each: no treatment (control group), radiation at 10 Gy, or radiation at 15 Gy. Each mouse received 5 x 10(5) highly metastasizing parent osteosarcoma cells injected into the left gastrocnemius muscle. Maximum tumor diameter was determined with a metric circles template to generate a tumor growth curve. Conscious mice were restrained in customized plastic jigs allowing local tumor irradiation. The behavior and development of the tumor xenograft were assessed via evaluations of the interval required for tumor-bearing limbs to reach diameters of 8 and 13 mm, extent of tumor vasculature, histomorphology of tumors, degree of tumor necrosis, and existence of pulmonary metastasis and clinical disease in affected mice. RESULTS: Tumor-bearing limbs grew to a diameter of 8 mm (0.2-g tumor mass) in a mean +/- SEM interval of 7.0 +/- 0.2 days in all mice. Interval to grow from 8 to 13 mm was significantly prolonged for both radiation therapy groups, compared with that of the control group. Histologic evaluation revealed the induced tumors were highly vascular and had characteristics consistent with those of osteosarcoma. Pulmonary metastasis was not detected, and there was no significant difference in percentage of tumor necrosis between groups. CONCLUSIONS AND CLINICAL RELEVANCE: A reliable, repeatable, and easily produced IM xenograft model was developed for in vivo assessment of canine osteosarcoma.

Intrinsic radiosensitivity and repair of sublethal radiation-induced damage in canine osteosarcoma cell lines.

OBJECTIVE: To characterize the radiosensitivity and capacity for sublethal damage repair (SLDR) of radiation-induced injury in 4 canine osteosarcoma cell lines. SAMPLE POPULATION: 4 canine osteosarcoma cell lines (HMPOS, POS, COS 31, and D17). PROCEDURES: A clonogenic colony-forming assay was used to evaluate the cell lines' intrinsic radiosensitivities and SLDR capacities. Dose-response curves for the cell lines were generated by fitting the surviving fractions after radiation doses of 0 (control cells), 1, 2, 3, 6, and 9 Gy to a linear quadratic model. To evaluate SLDR, cell lines were exposed to 2 doses of 3 Gy (split-dose experiments) at an interval of 0 (single 6-Gy dose), 2, 4, 6, or 24 hours, after which the surviving fractions were assessed. RESULTS: Mean surviving fraction did not differ significantly among the 4 cell lines at the radiation doses tested. Mean surviving fraction at 2 Gy was high (0.62), and the alpha/beta ratios (predictor of tissue sensitivity to radiation therapy) for the cell lines were low (mean ratio, 3.47). The split-dose experiments revealed a 2.8- to 3.9-fold increase in cell survival when the radiation doses were applied at an interval of 24 hours, compared with cell survival after radiation doses were applied consecutively (0-hour interval). CONCLUSIONS AND CLINICAL RELEVANCE: Results indicated that these canine osteosarcoma cell lines are fairly radioresistant; alpha/beta ratios were similar to those of nonneoplastic, late-responding tissues. Future clinical investigations should involve increasing the fraction size in a manner that maximizes tumor killing without adverse effects on the nonneoplastic surrounding tissues.

An investigation of the potential of rapid prototyping technology for image guided surgery.

Image-guided surgery can be broken down into two broad categories: frame-based guidance and frameless guidance. In order to reduce both the invasive nature of stereotactic guidance and the cost in equipment and time, we have developed a new guidance technique based on rapid prototyping (RP) technology. This new system first builds a computer model of the patient anatomy and then fabricates a physical reference frame that provides a precise and unique fit to the patient anatomy. This frame incorporates a means of guiding the surgeon along a preplanned surgical trajectory. This process involves (1) obtaining a high-resolution CT or MR scan, (2) building a computer model of the region of interest, (3) developing a surgical plan and physical guide, (4) designing a frame with a unique fit to the patient's anatomy with a physical linkage to the surgical guide, and (5) fabricating the frame using an RP unit. Software was developed to support these processes. To test the accuracy of this process, we first scanned and reproduced a plastic phantom fabricated to validate the system's ability to build an accurate virtual model. A target on the phantom was then identified, a surgical approach planned, a surgical guide designed, and the accuracy and precision of guiding a probe to that target were determined. Steps 1 through 5 were also evaluated using a head phantom. The results show that the RP technology can replicate an object from CT scans with submillimeter resolution. The fabricated reference frames, when positioned on the surface of the phantom and used to guide a surgical probe, can position the probe tip with an accuracy of 1.7 mm at the probe tip. These results demonstrate that the RP technology can be used for the fabrication of customized positioning frames for use in image-guided surgery.

Chord-based versus voxel-based methods of electron transport in the skeletal tissues.

Anatomic models needed for internal dose assessment have traditionally been developed using mathematical surface equations to define organ boundaries, shapes, and their positions within the body. Many researchers, however, are now advocating the use of tomographic models created from segmented patient computed tomography (CT) or magnetic resonance (MR) scans. In the skeleton, however, the tissue structures of the bone trabeculae, marrow cavities, and endosteal layer are exceedingly small and of complex shape, and thus do not lend themselves easily to either stylistic representations or in-vivo CT imaging. Historically, the problem of modeling the skeletal tissues has been addressed through the development of chord-based methods of radiation particle transport, as given by studies at the University of Leeds (Leeds, U.K.) using a 44-year male subject. We have proposed an alternative approach to skeletal dosimetry in which excised sections of marrow-intact cadaver spongiosa are imaged directly via microCT scanning. The cadaver selected for initial investigation of this technique was a 66-year male subject of nominal body mass index (22.7 kg m(-2)). The objectives of the present study were to compare chord-based versus voxel-based methods of skeletal dosimetry using data from the UF 66-year male subject. Good agreement between chord-based and voxel-based transport was noted for marrow irradiation by either bone surface or bone volume sources up to 500-1000 keV (depending upon the skeletal site). In contrast, chord-based models of electron transport yielded consistently lower values of the self-absorbed fraction to marrow tissues than seen under voxel-based transport at energies above 100 keV, a feature directly attributed to the inability of chord-based models to account for nonlinear electron trajectories. Significant differences were also noted in the dosimetry of the endosteal layer (for all source tissues), with chord-based transport predicting a higher fraction of energy deposition than given by voxel-based transport (average factor of about 1.6). The study supports future use of voxel-based skeletal models which (1) permit nonlinear electron trajectories across the skeletal tissues, (2) do not rely on mathematical algorithms for treating the endosteal tissue layer, and (3) do not implicitly assume independence of marrow and bone trajectories as is the case for chord-based skeletal models.

A comparison of skeletal chord-length distributions in the adult male.

In radiation protection, skeletal dose estimates are required for the tissues of the hematopoietically active bone marrow and the osteogenic cells of the trabecular and cortical endosteum. Similarly, skeletal radiation dose estimates are required in therapy nuclear medicine in order to develop dose-response functions for myelotoxicity where active bone marrow is generally the dose-limiting organ in cancer radioimmunotherapy. At the present time, skeletal dose models in both radiation protection and medical dosimetry are fundamentally reliant on a single set of chord-length distribution measurements performed at the University of Leeds in the late 1970's for a 44-y-old male subject. These distributions describe the relative frequency at which linear pathlengths are seen across both the marrow cavities and bone trabeculae in seven individual bone sites: vertebrae (cervical and lumbar), proximal femur (head and neck), ribs, cranium (parietal bone), and pelvis (iliac crest). In the present study, we present an alternative set of chord-length distribution data acquired within a total of 14 skeletal sites of a 66-y-old male subject. The University of Florida (UF) distributions are assembled via 3D image processing of microCT scans of physical sections of trabecular spongiosa at each skeletal site. In addition, a tri-linear interpolation Marching Cube algorithm is employed to smooth the digital surfaces of the bone trabeculae while chord-length measurements are performed. A review of mean chord lengths indicate that larger marrow cavities are noted on average in the UF individual for the cervical vertebrae (1,038 vs. 910 microm), lumbar vertebrae (1,479 vs. 1,233 microm), ilium (1,508 vs. 904 microm), and parietal bone (812 vs. 389 microm), while smaller marrow cavities are noted in the UF individual for the femoral head (1,043 microm vs. 1,157 microm), the femoral neck (1,454 microm vs. 1,655 microm), and the ribs (1,630 microm vs. 1,703 microm). The mean chord-lengths for the bone trabeculae show close agreement for both individuals in the ilium (approximately 240 microm) and cervical vertebrae (approximately 280 microm). Thicker trabeculae were seen on average in the UF individual for the femoral head (ratio of 1.50), femoral neck (ratio of 1.10), lumbar vertebrae (ratio of 1.29), and ribs (ratio of 1.14), while thinner trabeculae were seen on average in the UF individual for the parietal bone of the cranium (ratio of 0.92). In two bone sites, prominent discrepancies in chord distribution shape were noted between the Leeds 44-y-old male and the UF 66-y-old male: (1) the bone trabeculae in the ribs, and (2) the marrow cavities and bone trabeculae within the cranium.

Absorbed fractions for alpha-particles in tissues of trabecular bone: considerations of marrow cellularity within the ICRP reference male.

UNLABELLED: Alpha-particles are of current interest in radionuclide therapy due to their short range and high rates of energy transfer to target tissues. Published values of alpha-particle absorbed fraction phi in the skeletal tissues, as needed for patient-specific dosimetry under the MIRD schema, do not generally account for its variation with particle energy or skeletal site. Furthermore, variations in alpha-particle absorbed fraction with marrow cellularity have yet to be fully considered. METHODS: In this study, a 3-dimensional (3D) chord-based radiation transport model (or 3D-CBIST) is presented, which combines (a) chord-based techniques for tracking alpha-particles across bone trabeculae, endosteum, and marrow cavities and (b) a spatial model of the marrow tissues that explicitly considers the presence of marrow adipocytes. Chord-length distributions are taken from a 44-y male subject (ICRP [International Commission on Radiological Protection] Reference Male) and are identical to those used currently for clinical dose estimates for beta-particle emitters. RESULTS: Values of phi(active marrow<--active marrow) given by the 3D-CBIST model are shown to be considerably lower than phi = 1.0 assumed under the ICRP Publication 30 and 2003 Eckerman bone models. For example, values of absorbed fraction for the self-dose to active bone marrow in the ribs, cervical vertebra, and parietal bone are 0.81, 0.80, and 0.55 for 6-MeV alpha-particles and are 0.74, 0.72, and 0.43 for 9-MeV alpha-particles, where each is evaluated at ICRP reference cellularities in the 3D-CBIST model (72%, 72%, and 42%, respectively, at age 25 y). CONCLUSION: Improvements in patient-specific dosimetry of skeletal tissues require explicit consideration of not only changes in target mass with variable patient marrow cellularity (i.e., active marrow) but also corresponding changes in values of the absorbed fraction. The data given in this study provide a more-firm basis for application of the MIRD schema to patient-specific dosimetry for newly developing therapies using alpha-particle emitters.

Accounting for beta-particle energy loss to cortical bone via paired-image radiation transport (PIRT).

Current methods of skeletal dose assessment in both medical physics (radionuclide therapy) and health physics (dose reconstruction and risk assessment) rely heavily on a single set of bone and marrow cavity chord-length distributions in which particle energy deposition is tracked within an infinite extent of trabecular spongiosa, with no allowance for particle escape to cortical bone. In the present study, we introduce a paired-image radiation transport (PIRT) model which provides a more realistic three-dimensional (3D) geometry for particle transport in the skeletal site at both microscopic and macroscopic levels of its histology. Ex vivo CT scans were acquired of the pelvis, cranial cap, and individual ribs excised from a 66-year male cadaver (BMI of 22.7 kg m(-2)). For the three skeletal sites, regions of trabecular spongiosa and cortical bone were identified and segmented. Physical sections of interior spongiosa were taken and subjected to microCT imaging. Voxels within the resulting microCT images were then segmented and labeled as regions of bone trabeculae, endosteum, active marrow, and inactive marrow through application of image processing algorithms. The PIRT methodology was then implemented within the EGSNRC radiation transport code whereby electrons of various initial energies are simultaneously tracked within both the ex vivo CT macroimage and the CT microimage of the skeletal site. At initial electron energies greater than 50-200 keV, a divergence in absorbed fractions to active marrow are noted between PIRT model simulations and those estimated under existing techniques of infinite spongiosa transport. Calculations of radionuclide S values under both methodologies imply that current chord-based models may overestimate the absorbed dose to active bone marrow in these skeletal sites by 0% to 27% for low-energy beta emitters (33P, 169Er, and 177Lu), by approximately 4% to 49% for intermediate-energy beta emitters (153Sm, 186Re, and 89Sr), and by approximately 14% to 76% for high-energy beta emitters (32p, 188Re, and 90Y). The PIRT methodology allows for detailed modeling of the 3D macrostructure of individual marrow-containing bones within the skeleton thus permitting improved estimates of absorbed fractions and radionuclide S values for intermediate-to-high energy beta emitters.

A paired-image radiation transport model for skeletal dosimetry.

UNLABELLED: Toxicity of the hematopoietically active bone marrow continues to be a primary limitation in radionuclide therapies of cancer. Improved techniques for patient-specific skeletal dosimetry are thus crucial to the development of dose-response relationships needed to optimize these therapies (i.e., avoid both marrow toxicity and tumor underdosing). Current clinical methods of skeletal dose assessment rely heavily on a single set of bone and marrow cavity chord-length distributions in which particle energy deposition is tracked within an infinite extent of trabecular spongiosa, with no allowance for particle escape to cortical bone. In the present study, we introduce a paired-image radiation transport (PIRT) model that can provide a more realistic 3-dimensional geometry for particle transport of the skeletal site at both microscopic and macroscopic levels of its histology. METHODS: Ex vivo CT scans were acquired of the lumbar vertebra and right proximal femur excised from a 66-y male cadaver (body mass index, 22.7 kg m(-2)). For both skeletal sites, regions of trabecular spongiosa and cortical bone were identified and segmented. Physical sections of interior spongiosa were then taken and subjected to nuclear magnetic resonance (NMR) microscopy. Voxels within the resulting NMR microimages were segmented and labeled into regions of bone trabeculae, endosteum, active marrow, and inactive marrow. The PIRT methodology was then implemented within the EGSnrc radiation transport code, whereby electrons of various initial energies are simultaneously tracked within both the ex vivo CT macroimage and the NMR microimage of the skeletal site. RESULTS: At electron initial energies greater than 50-200 keV, a divergence in absorbed fractions to active marrow is noted between PIRT model simulations and those estimated under infinite spongiosa transport techniques. Calculations of radionuclide S values under both methodologies imply that current chord-based models used in clinical skeletal dosimetry can overestimate dose to active bone marrow in these 2 skeletal sites by approximately 4%-23% for low-energy beta-emitters ((33)P, (169)Er, and (177)Lu), by approximately 4%-25% for intermediate-energy beta-emitters ((153)Sm, (186)Re, and (89)Sr), and by approximately 11%-30% for high-energy beta-emitters ((32)P, (188)Re, and (90)Y). CONCLUSION: The PIRT methodology allows for detailed modeling of the 3D macrostructure of individual marrow-containing bones within the skeleton, thus permitting improved estimates of absorbed fractions and radionuclide S values for intermediate-to-high beta-emitters.

Uncertainties in electron-absorbed fractions and lung doses from inhaled beta-emitters.

The computer code LUDUC (Lung Dose Uncertainty Code), developed at the University of Florida, was originally used to investigate the range of potential doses from the inhalation of either plutonium or uranium oxides. The code employs the ICRP Publication 66 Human Respiratory Tract model; however, rather than using simple point estimates for each of the model parameters associated with particle deposition, clearance, and lung-tissue dosimetry, probability density functions are ascribed to these parameters based upon detailed literature review. These distributions are subsequently sampled within LUDUC using Latin hypercube sampling techniques to generate multiple (e.g., approximately 1,000) sets of input vectors (i.e., trials), each yielding a unique estimate of lung dose. In the present study, the dosimetry component of the ICRP-66 model within LUDUC has been extended to explicitly consider variations in the beta particle absorbed fraction due to corresponding uncertainties and biological variabilities in both source and target tissue depths and thicknesses within the bronchi and bronchioles of the thoracic airways. Example dose distributions are given for the inhalation of absorption Type S compounds of 90Sr (Tmax = 546 keV) and 90Y (Tmax = 2,284 keV) as a function of particle size. Over the particle size range of 0.001 to 1 microm, estimates of total lung dose vary by a factor of 10 for 90Sr particles and by a factor of 4 to 10 for 90Y particles. As the particle size increases to 10 microm, dose uncertainties reach a factor of 100 for both radionuclides. In comparisons to identical exposures scenarios run by the LUDEP 2.0 code, Reference Man doses for inhaled beta-emitters were shown to provide slightly conservative estimates of lung dose compared to those in this study where uncertainties in lung airway histology are considered.

MIRD Pamphlet No 19: absorbed fractions and radionuclide S values for six age-dependent multiregion models of the kidney.

UNLABELLED: As one of the major organs of the excretory pathway, the kidneys represent a frequent source of radiopharmaceutical uptake in both diagnostic and therapeutic nuclear medicine. The unique organization of the functional tissues of the organ ensures transient changes in suborgan localization of renal activity. Current single-region dosimetric models of the kidneys, however, force the assumption of a uniform distribution of radioactivity across the entire organ. The average absorbed dose to the kidneys predicted by such models can misrepresent local regional doses to specific substructures. METHODS: To facilitate suborgan dosimetry for the kidneys, 6 new age-dependent multiregion kidney models are presented. The outer dimensions of the models conform to those used currently in single-region kidney models, whereas interior structures are defined for the renal cortex, the medullary pyramids with papillae (2 vertical and 3 horizontal), and the renal pelvis. Absorbed fractions of energy were calculated for both photon and electron sources (10 keV to 4 MeV) located in each source region within the 6 age-dependent models. The absorbed fractions were then used to assemble S values for radionuclides of potential interest in suborgan kidney dosimetry. RESULTS: For the adult, the absorbed dose to the renal cortex for (90)Y-labeled compounds retained within that subregion is approximately 1.3 times that predicted by the single-region kidney model, whereas the medullary dose is only 26% of that same single-region value. For compounds that are rapidly filtered in the kidneys, the renal cortex dose is approximately one-half of that predicted under the single-region model, whereas the tissues of the medullary pyramids receive an absorbed dose 1.5-1.8 times larger. CONCLUSION: The multiregion model described here permits estimates of regional kidney dose not previously supported by current single-region models. Full utilization of the new model, however, requires serial imaging of the kidneys with regions of interest assigned to the renal cortex and medulla.

Adipocyte spatial distributions in bone marrow: implications for skeletal dosimetry models.

UNLABELLED: Few studies have been conducted to quantify the spatial distributions of adipocytes in the marrow cavities of trabecular bone. Nevertheless, such data are needed for the development of 3-dimensional (3D) voxel skeletal models where marrow cellularity is explicitly considered as a model parameter for dose assessment. In this investigation, bone marrow biopsies of the anterior iliac crest were examined to determine the size distribution of adipocyte cell clusters, the percentage of perimeter coverage of trabecular surfaces, and the presence or absence of adipocyte density gradients in the marrow space, all as a function of the biopsy marrow cellularity (5%-95%). METHODS: Biopsy slides from 42 patients were selected as designated by the hematopathologist as either normocellular or with no evidence of disease. Still-frame video image captures were made of 1-3 regions of interest per biopsy specimen, with subsequent image analysis of adipocyte spatial characteristics performed via a user-written MATLAB routine. RESULTS: A predictable shift was found in cluster size with decreasing marrow cellularity from single adipocytes to clusters of >or=3 cells; the percentage of 2-cell clusters remained relatively constant with changing cellularity. Also, a nonlinear increase in trabeculae perimeter coverage was found with increasing fat tissue fraction at marrow cellularities between 50% and 80%. Finally, it was demonstrated that only in the range of 20%-50% marrow cellularity was a slight gradient in adipocyte concentration indicated with adipocytes localized preferentially toward the trabecular surfaces. CONCLUSION: Electron transport simulations were conducted in 4 different 3D voxel models of trabecular bone for sources localized in the active marrow (TAM), bone volume (TBV), bone endosteum (TBE), and bone surfaces (TBS). Voxel model simulations demonstrated that absorbed fractions to active marrow given by the ICRP 30 model (MIRDOSE2) are exceedingly conservative for both TBV and TBS sources, except in the case of high-energy particles (>500 keV) at high values of marrow cellularity (>70%). Values of both phi(TAM<--TBV) and phi(TAM<--TBS) given by the Eckerman and Stabin model (MIRDOSE3) were shown to be reasonably consistent with 3D voxel model simulations at the reference cellularity of 25%, except in the case of low-energy emitters (<100 keV) on the bone surfaces.

Considerations of marrow cellularity in 3-dimensional dosimetric models of the trabecular skeleton.

UNLABELLED: Dose assessment to active bone marrow is a critical feature of radionuclide therapy treatment planning. Skeletal dosimetry models currently used to assign radionuclide S values for clinical marrow dose assessment are based on bone and marrow cavity chord-length distributions. Accordingly, these models cannot explicitly consider energy loss to inactive marrow (adipose tissue) during particle transport across the trabecular marrow space (TMS). One method to account for this energy loss is to uniformly scale the resulting TMS absorbed fractions by reference values of site-specific marrow cellularity. In doing so, however, the resulting absorbed fractions for self-irradiation of the trabecular active marrow (TAM) do not converge to unity at low electron source energies. This study attempts to address this issue by using nuclear magnetic resonance microscopy images of trabecular bone to define 3-dimensional (3D) dosimetric models in which explicit spatial distributions of adipose tissue are introduced. METHODS: Cadaveric sources of trabecular bone were taken from both the femoral heads and humeral epiphyses of a 51-y-old male subject. The bone sites were sectioned and subsequently imaged at a proton resonance frequency of 200 MHz (4.7 T) using a 3D spin-echo pulse sequence. After image segmentation, voxel clusters of adipocytes were inserted interior to the marrow cavities of the binary images, which were then coupled to the EGS4 radiation transport code for simulation of active marrow electron sources. RESULTS: Absorbed fractions for self-irradiation of the TAM were tabulated for both skeletal sites. Substantial variations in the absorbed fraction to active marrow are seen with changes in marrow cellularity, particularly in the energy range of 100-500 keV. These variations are seen to be more dramatic in the humeral epiphysis (larger marrow volume fraction) than in the femoral head. CONCLUSION: Results from electron transport in 3D models of the trabecular skeleton indicate that current methods to account for marrow cellularity in chord-based models are incomplete. At 10 keV, for example, the Eckerman and Stabin model underestimates the self-absorbed fraction to active marrow by 75%. At 1 MeV, the model of Bouchet et al. overestimates this same value by 40%. In the energy range of 20-200 keV, neither model accurately predicts energy loss to the active bone marrow. Thus, it is proposed that future extensions of skeletal dosimetry models use 3D transport techniques in which explicit delineation of active and inactive marrow is feasible.