Assessing the Accuracy of Cone-Beam Computerized Tomography in Measuring Thinning Oral and Buccal Bone.

The aim of this study was to assess the accuracy and reliability of cone-beam computerized tomography (CBCT) in measuring thinning bone surrounding dental implants. Three implants were inserted into the mandible of a domestic pig at 6 different bone thicknesses on the vestibular and the lingual sides, and measurements were recorded using CBCT. The results were obtained, analyzed, and compared with areas without implants. Our results indicated that the bone thickness and the neighboring implants decreased the accuracy and reliability of CBCT for measuring bone volume around dental implants. We concluded that CBCT slightly undermeasured the bone thickness around the implant, both buccally and orally, compared with the same thickness without the implant. These results support that using the i-CAT NG with a 0.2 voxel size is not accurate for either qualitative or quantitative bone evaluations, especially when the bone is thinner than 0.72 mm in the horizontal dimension.

[Surgery on virtual model and 3-dimensional printing of a surgical wafer for the correction of a severe mandibular asymmetry]. / Virtuális modell-mutét és az okklúziós lemez háromdimenziós nyomtatása súlyos mandibula aszimmetria esetében.

Correction of a severe facial asymmetry presents a challenge due to the geometric complexity of the dentition, the bony structures and the soft tissues. In most asymmetric cases two-jaw surgery is recommended. Manual model surgery is an essential part of treatment planning but it can be complicated, time-consuming and may contain potential errors. We present a case of a 26-year-old male with a severe right-sided hemimandibular elongation when computerized simulation surgery was performed instead of manual model surgery. High-resolution computer tomography scan was done following presurgical orthodontics and the stack images were reformatted into a three-dimensional structure. The symmetry of the maxilla was corrected via a virtual Le Fort I osteotomy with the help of a three-dimensional planning software. A virtual intermediate surgical wafer was designed and fabricated with a three-dimensional printer. Virtual bilateral sagittal split osteotomy was performed and the mandible was rotated into the correct position to visualize the movements of the osteotomized segments. Real surgery was accomplished according to the virtual plan. The splint fitted well. There is a significant improvement in the facial symmetry; the occlusion is good and stable. This case supports the usage of computer-aided surgical planning and three-dimensional rapid prototyping for the correction of facial asymmetries.

Correction of a severe facial asymmetry with computerized planning and with the use of a rapid prototyped surgical template: a case report/technique article.

Management of significant facial asymmetry presents a challenge due to the geometric complexity of the bony and other facial structures. Manual model surgery is an essential part of treatment planning but it can be complicated, time-consuming and may contain potential errors. Computer-aided surgery has revolutionized the correction of maxillofacial deformities. The aim of this study was to report a case of facial asymmetry when computerised simulation surgery was performed instead of manual model surgery and a virtually planned wafer splint was fabricated. A 26-year-old male was presented with a severe right-sided hemimandibular elongation. Following presurgical orthodontics high-resolution computer tomography scan was performed. The stack images were reformatted into a three-dimensional structure. Virtual Le Fort-I osteotomy was performed and the symmetry of the maxilla was corrected with the help of a three-dimensional planning software. A virtual intermediate surgical wafer was designed and produced with three-dimensional rapid prototyping technology. The mandible was rotated into the correct position following virtual bilateral sagittal split osteotomy to visualize the movements of the osteotomised mandibular segments. The two-jaw procedure was performed according to the virtual plan. The facial symmetry was improved significantly and stable occlusion was achieved. This complex case shows the advantages of computer-aided surgical planning and three-dimensional rapid prototyping for the correction of facial asymmetries.

[Knowledge of the management of dental trauma in southern Hungary]. / Traumás fogsérülések ellátásával kapcsolatos ismeretek vizsgálata Dél-Magyarországon.

The aim of the study was to evaluate the knowledge of dental trauma management in the southern part of Hungary among parents, teachers, medical doctors and dentists. A cross-sectional study was performed among the mentioned groups, with a structured questionnaire. The participants consisted of 275 people, most of them were parents (185), the other groups were smaller (30-30). 73.62% of parents recognised that the maxillary incisor of a 9-year-old girl is probably a permanent tooth. In case of the coronal fracture of this tooth 65.03% responded correctly. The correct response rate for the management of an avulsed tooth was only 39.26%, but in case of loss of consciousness 92.64% would act correctly. The Chi-square test indicated that there was a significant association between the correct recognition of the type of incisor and higher education (p < 0.01), and the number of seen TDIs. The 76.7% of the parents was not satisfied with his knowledge about TDLs, and 74.9% was interested in more information. In our study the parents performed generally better compared to other studies, but compared to the other three groups their results were worse. The knowledge of the teachers and the doctors was almost equivalent. The dentist had the best results. The level of knowledge of dental trauma management was inadequate among parents, but the teachers and doctors should improve their knowledge too. We suggest that it's necessary to start educational campaigns among groups that could be the primary caregivers of traumatic dental injuries.

Neglected Basal cell carcinomas in the 21st century.

Although tumors on the surface of the skin are considered to be easily recognizable, neglected advanced skin neoplasms are encountered even in the 21st century. There can be numerous causes of the delay in the diagnosis: fear of the diagnosis and the treatment, becoming accustomed to a slowly growing tumor, old age, a low social milieu, and an inadequate hygienic culture are among the factors leading some people not to seek medical advice. The treatment of such advanced neoplasms is usually challenging. The therapy of neglected cases demands an individual multidisciplinary approach and teamwork. Basal cell carcinoma (BCC), the most common cutaneous tumor, usually develops in the elderly, grows slowly, and has an extremely low metastatic potential; these factors are suggesting that BCCs might well be the "ideal candidates" for neglected tumors. Five neglected advanced cases of BCC were diagnosed in our dermatological institute between 2000 and 2009. The clinical characteristics and treatment modalities of these neoplasms are discussed, together with the possible causes of the neglect.