ABSTRACT
This work presents the development of a cavity ring-down spectrometer (CRDS) designed for the detection of several molecules relevant for air pollution, including the second overtone of ro-vibration transitions from CO at 1.58 µm and NO at 1.79 µm. A unique feature of this CRDS is the use of custom mirrors with a reflectivity of about 99.99% from 1.52 to 1.80 µm, enabling efficient laser coupling into the cavity while ensuring a minimum detectable absorbance of 1.1 × 10-10 cm-1 within an integration time of about 1.2 s. In this work, the successful implementation of the current CRDS is demonstrated in two different wavelength regions. At 1.79 µm, the transitions R17.5 and R4.5 of the second overtone of NO are detected. At 1.58 µm, carbon dioxide and water vapor from untreated ambient air are measured, serving as an example to investigate the suitability of a post-processing procedure for the determination of the molar fraction in a multi-species composition. This post-processing procedure has the benefit of being calibration-free and SI-traceable. Additionally, CRDS measurements of gas mixtures containing CO and CO2 are also shown. In the future, the advantages of the developed cavity ring-down spectrometer will be exploited in order to perform fundamental studies on the transport processes of heterogeneous catalysis by locally resolving the gas phase near a working catalytic surface. The possibility to cover a broad wavelength region with this CRDS opens up the opportunity to investigate different catalytic reactions, including CO oxidation and NO reduction.
ABSTRACT
Cell spraying has become a feasible application method for cell therapy and tissue engineering approaches. Different devices have been used with varying success. Often, twin-fluid atomizers are used, which require a high gas velocity for optimal aerosolization characteristics. To decrease the amount and velocity of required air, a custom-made atomizer was designed based on the effervescent principle. Different designs were evaluated regarding spray characteristics and their influence on human adipose-derived mesenchymal stromal cells. The arithmetic mean diameters of the droplets were 15.4−33.5 µm with decreasing diameters for increasing gas-to-liquid ratios. The survival rate was >90% of the control for the lowest gas-to-liquid ratio. For higher ratios, cell survival decreased to approximately 50%. Further experiments were performed with the design, which had shown the highest survival rates. After seven days, no significant differences in metabolic activity were observed. The apoptosis rates were not influenced by aerosolization, while high gas-to-liquid ratios caused increased necrosis levels. Tri-lineage differentiation potential into adipocytes, chondrocytes, and osteoblasts was not negatively influenced by aerosolization. Thus, the effervescent aerosolization principle was proven suitable for cell applications requiring reduced amounts of supplied air. This is the first time an effervescent atomizer was used for cell processing.
ABSTRACT
Introduction: Bronchoscopic spraying has potential for the application of therapeutic drugs in distal regions of the lung by bypassing the upper airways. However, there is a lack of understanding about the underlying fluid transport phenomena that are responsible for the intrapulmonary propagation of applied liquid. Methods: By using a transparent airway model, this study provides first experimental insights into relevant transport phenomena of bronchoscopic spraying. Furthermore, the penetration depth of the application is quantitatively evaluated. Laser-induced fluorescence is used to analyze fluid propagation in the transparent channels. Potential influencing factors such as the positioning in different airways, application number, breathing pattern, and lung obstructions are varied within this study to determine their influence on liquid deposition. Findings: This study shows that the method of bronchoscopic spraying allows the application of liquid in distal regions of the airway model. The position of the bronchoscope is a key influencing factor in increasing the penetration depth. We found that fluid transport along the distal airways essentially occurs by the film and plug flow phenomenon during application, which is similar to the transport mechanisms during instillation. Liquid plugs in lower airways are responsible for the reorganization of liquid during proximal movements and thereby influence the penetration depth in subsequent applications.
Subject(s)
Lung , Trachea , Administration, Inhalation , FluorescenceABSTRACT
A new design for transparent high-pressure nozzles is presented in this work. This new design enables using the innovative Selective Laser Etching (SLE) method to manufacture transparent nozzles with outstanding accuracy. Therefore, not only the simultaneous visualization of the flow mechanics inside and outside the nozzle is enabled, but the manufacturing method applied also allows for the realization of individual nozzle geometries. Thus, nozzle internal flow phenomena (e.g., cavitation, swirl, and air inlet) and their influence on primary breakup can be analyzed with realistic nozzle geometries, e.g., for automotive applications. In addition, targeted three dimensional nozzle geometric parameters can be designed and manufactured in order to get specific tailor-made spray characteristics (e.g., droplet size distribution, spray angle, and penetration length). The basis for the transparent nozzle design is a two-parted nozzle, consisting of a re-machined original serial nozzle body and a transparent nozzle tip. The innovative SLE is used to produce the geometry of the transparent nozzle tip in fused silica, and laser polishing is utilized to achieve a maximum optical quality of nozzle surfaces for visualization. Bonding of both nozzle parts is achieved by a specially designed adhesive method. For a first feasibility study, a transparent nozzle with a simplified nozzle geometry is manufactured and used for a first study. In this study, simultaneous investigation of nozzle internal flow phenomena and their impact on spray breakup are visualized. First microscopic images of the nozzle internal flow show the formation of cavitation, its effect on nozzle internal temperature (apparent by differences in the fluid refractive index), and also the corresponding impact on spray breakup during injection. The penetration of ambient gas into the nozzle is verified at the end of injection as well as the influence of this air on the spray formation during the start of injection.
ABSTRACT
This work presents a novel high-speed interferometric thickness measurement system for thin films (1 µm-23 µm). The system is based on a Fizeau-interferometer and combines a high-speed camera for 2-D topographic fringe images with a spectrally resolved white light interferometer. The aim of this combination is to overcome the ambiguities of the phase demodulation process during fringe pattern analysis. The system is able to measure spatially and temporally resolved film thickness distributions during fast processes. The measurement error of the system is around 5% compared to a commercial 0-D interferometer. First, the results during a diesel spray impingement onto a predefined diesel film are shown, and at the impingement point, an increase in a fluid volume of 24.3% can be seen.
ABSTRACT
Ballistic imaging commonly denotes the formation of line-of-sight shadowgraphs through turbid media by suppression of multiply scattered photons. The technique relies on a femtosecond laser acting as light source for the images and as switch for an optical Kerr gate that separates ballistic photons from multiply scattered ones. The achievable image resolution is one major limitation for the investigation of small objects. In this study, practical influences on the optical Kerr gate and image quality are discussed theoretically and experimentally applying a switching beam with large aperture (D = 19 mm). It is shown how switching pulse energy and synchronization of switching and imaging pulse in the Kerr cell influence the gate's transmission. Image quality of ballistic imaging and standard shadowgraphy is evaluated and compared, showing that the present ballistic imaging setup is advantageous for optical densities in the range of 8 < OD < 13. Owing to the spatial transmission characteristics of the optical Kerr gate, a rectangular aperture stop is formed, which leads to different resolution limits for vertical and horizontal structures in the object. Furthermore, it is reported how to convert the ballistic imaging setup into a schlieren-type system with an optical schlieren edge.