In-Flight Tuning of Au-Sn Nanoparticle Properties.

Multimetallic nanoparticles possess a variety of beneficial properties with potential relevance for various applications. These metallic nanoparticles can consist of randomly ordered alloys, which retain the properties of the constituting elements, or ordered intermetallics, which possess extended properties. Depending on the desired application, specific alloys or intermetallic compounds are required. However, it remains challenging to achieve particular morphologies, crystal structures, chemical compositions, and particle sizes because of the inherent complexity of nanoparticle synthesis. In this work, Au-Sn nanoparticles were synthesized using a continuous one-step gas-phase synthesis method that offers the possibility to anneal the nanoparticles in flight directly after generation to tune their properties. The bimetallic model system Au-Sn, comprising both alloys and intermetallic compounds, was studied in the temperature range of 300 to 1100 °C. The bimetallic Au/Sn ratio in the nanoparticles can be adjusted with in-flight annealing between 70/30 and 40/60 atomic %. While Au-rich alloys are obtained at lower temperatures, the increase in the annealing temperature leads to the formation of more Sn-rich intermetallic phases. Surface and size effects greatly influence particle morphologies and phase fractions. This research opens new opportunities for the synthesis of customized nanoparticles by temperature adjustment and particle size selection.

Zinc speciation in fly ash from MSWI using XAS - novel insights and implications.

The chemical forms of zinc in fly ash from municipal solid waste incineration (MSWI) crucially affect ash management, influencing both material recovery options and the risk of unwanted leaching into ecosystems. The zinc speciation was investigated in fly ash samples sourced from full-scale MSWI plants, including four grate fired boilers (GB) and one fluidized bed boiler (FB). We applied X-ray Absorption Spectroscopy (XAS), and the spectra were analyzed against a unique library of over 30 relevant compounds, tailored to the nuances of zinc chemistry of fly ash. Nano-XANES and sequential leaching were employed as complementary analytical methods. Multiple chemical forms of zinc were found in the ash, whereof potassium zinc chloride salts (K2ZnCl4) emerged as the predominant form in GB fly ash representing 41-64 % of the zinc content, while less for FB fly ash (19 %). The mere exposure to humidity in the air during storage resulted in hydroxylation of the alkali zinc chlorides into Zn5(OH)8Cl2·H2O. Other forms of zinc in the ash were Zn4Si2O7(OH)2·H2O, ZnFe2O4, ZnAl2O4, surface adsorbed zinc, and Zn5(CO3)2(OH)6. Notably, the proportion of zinc in spinel forms (ZnFe2O4 and ZnAl2O4) increased threefold in FB ash compared to GB ash, representing ∼60 % and ∼10-20 % of the zinc, respectively.

Dietary fatty acids modulate oxidative stress response to air pollution but not to infection.

Anthropogenic changes to the environment expose wildlife to many pollutants. Among these, tropospheric ozone is of global concern and a highly potent pro-oxidant. In addition, human activities include several other implications for wildlife, e.g., changed food availability and changed distribution of pathogens in cities. These co-occurring habitat changes may interact, thereby modulating the physiological responses and costs related to anthropogenic change. For instance, many food items associated with humans (e.g., food waste and feeders for wild birds) contain relatively more ω6-than ω3-polyunsaturated fatty acids (PUFAs). Metabolites derived from ω6-PUFAs can enhance inflammation and oxidative stress towards a stimulus, whereas the opposite response is linked to ω3-derived metabolites. Hence, we hypothesized that differential intake of ω6-and ω3-PUFAs modulates the oxidative stress state of birds and thereby affects the responses towards pro-oxidants. To test this, we manipulated dietary ω6:ω3 ratios and ozone levels in a full-factorial experiment using captive zebra finches (Taeniopygia guttata). Additionally, we simulated an infection, thereby also triggering the immune system's adaptive pro-oxidant release (i.e., oxidative burst), by injecting lipopolysaccharide. Under normal air conditions, the ω3-diet birds had a lower antioxidant ratio (GSH/GSSG ratio) compared to the ω6-diet birds. When exposed to ozone, however, the diet effect disappeared. Instead, ozone exposure overall reduced the total concentration of the key antioxidant glutathione (tGSH). Moreover, the birds on the ω6-rich diet had an overall higher antioxidant capacity (OXY) compared to birds fed a ω3-rich diet. Interestingly, only the immune challenge increased oxidative damage, suggesting the oxidative burst of the immune system overrides the other pro-oxidative processes, including diet. Taken together, our results show that ozone, dietary PUFAs, and infection all affect the redox-system, but in different ways, suggesting that the underlying responses are decoupled despite that they all increase pro-oxidant exposure or generation. Despite lack of apparent cumulative effect in the independent biomarkers, the combined single effects could together reduce overall cellular functioning and efficiency over time in wild birds exposed to pathogens, ozone, and anthropogenic food sources.

Characterization of airborne dust emissions from three types of crushed multi-walled carbon nanotube-enhanced concretes.

Dispersing Multi-Walled Carbon Nanotubes (MWCNTs) into concrete at low (<1 wt% in cement) concentrations may improve concrete performance and properties and provide enhanced functionalities. When MWCNT-enhanced concrete is fragmented during remodelling or demolition, the stiff, fibrous and carcinogenic MWCNTs will, however, also be part of the respirable particulate matter released in the process. Consequently, systematic aerosolizing of crushed MWCNT-enhanced concretes in a controlled environment and measuring the properties of this aerosol can give valuable insights into the characteristics of the emissions such as concentrations, size range and morphology. These properties impact to which extent the emissions can be inhaled as well as where they are expected to deposit in the lung, which is critical to assess whether these materials might constitute a future health risk for construction and demolition workers. In this work, the impact from MWCNTs on aerosol characteristics was assessed for samples of three concrete types with various amounts of MWCNT, using a novel methodology based on the continuous drop method. MWCNT-enhanced concretes were crushed, aerosolized and the emitted particles were characterized with online and offline techniques. For light-weight porous concrete, the addition of MWCNT significantly reduced the respirable mass fraction (RESP) and particle number concentrations (PNC) across all size ranges (7 nm - 20 µm), indicating that MWCNTs dampened the fragmentation process by possibly reinforcing the microstructure of brittle concrete. For normal concrete, the opposite could be seen, where MWCNTs resulted in drastic increases in RESP and PNC, suggesting that the MWCNTs may be acting as defects in the concrete matrix, thus enhancing the fragmentation process. For the high strength concrete, the fragmentation decreased at the lowest MWCNT concentration, but increased again for the highest MWCNT concentration. All tested concrete types emitted <100 nm particles, regardless of CNT content. SEM imaging displayed CNTs protruding from concrete fragments, but no free fibres were detected.

Characterization and Toxic Potency of Airborne Particles Formed upon Waste from Electrical and Electronic Equipment Waste Recycling: A Case Study.

Manual dismantling, shredding, and mechanical grinding of waste from electrical and electronic equipment (WEEE) at recycling facilities inevitably lead to the accidental formation and release of both coarse and fine particle aerosols, primarily into the ambient air. Since diffuse emissions to air of such WEEE particles are not regulated, their dispersion from the recycling plants into the adjacent environment is possible. The aim of this interdisciplinary project was to collect and characterize airborne WEEE particles smaller than 1 µm generated at a Nordic open waste recycling facility from a particle concentration, shape, and bulk and surface composition perspective. Since dispersed airborne particles eventually may reach rivers, lakes, and possibly oceans, the aim was also to assess whether such particles may pose any adverse effects on aquatic organisms. The results show that WEEE particles only exerted a weak tendency toward cytotoxic effects on fish gill cell lines, although the exposure resulted in ROS formation that may induce adverse effects. On the contrary, the WEEE particles were toxic toward the crustacean zooplankter Daphnia magna, showing strong effects on survival of the animals in a concentration-dependent way.

An experimental study on lung deposition of inhaled 2 µm particles in relation to lung characteristics and deposition models.

BACKGROUND: The understanding of inhaled particle respiratory tract deposition is a key link to understand the health effects of particles or the efficiency for medical drug delivery via the lung. However, there are few experimental data on particle respiratory tract deposition, and the existing data deviates considerably when comparing results for particles > 1 µm. METHODS: We designed an experimental set-up to measure deposition in the respiratory tract for particles > 1 µm, more specifically 2.3 µm, with careful consideration to minimise foreseen errors. We measured the deposition in seventeen healthy adults (21-68 years). The measurements were performed at tidal breathing, during three consecutive 5-minute periods while logging breathing patterns. Pulmonary function tests were performed, including the new airspace dimension assessment (AiDA) method measuring distal lung airspace radius (rAiDA). The lung characteristics and breathing variables were used in statistical models to investigate to what extent they can explain individual variations in measured deposited particle fraction. The measured particle deposition was compared to values predicted with whole lung models. Model calculations were made for each subject using measured variables as input (e.g., breathing pattern and functional residual capacity). RESULTS: The measured fractional deposition for 2.3 µm particles was 0.60 ± 0.14, which is significantly higher than predicted by any of the models tested, ranging from 0.37 ± 0.08 to 0.53 ± 0.09. The multiple-path particle dosimetry (MPPD) model most closely predicted the measured deposition when using the new PNNL lung model. The individual variability in measured particle deposition was best explained by breathing pattern and distal airspace radius (rAiDA) at half inflation from AiDA. All models underestimated inter-subject variability even though the individual breathing pattern and functional residual capacity for each participant was used in the model. CONCLUSIONS: Whole lung models need to be tuned and improved to predict the respiratory tract particle deposition of micron-sized particles, and to capture individual variations - a variation that is known to be higher for aged and diseased lungs. Further, the results support the hypothesis that the AiDA method measures dimensions in the peripheral lung and that rAiDA, as measured by the AiDA, can be used to better understand the individual variation in the dose to healthy and diseased lungs.

Sensitive methods for assessment of lung health in welders and controls.

BACKGROUND: Welders are exposed to gas and particle emissions that can cause severe lung disease, such as chronic obstructive pulmonary disease (COPD), a leading cause of mortality and morbidity worldwide. It is difficult to detect COPD early and therefore mitigating measures may be delayed. The aim of this study was to investigate lung health in welders and evaluate new sensitive methods with potential to assess early onset pulmonary changes in occupational settings. METHODS: This study assessed the lung health and symptoms in active welders (n = 28) and controls (n = 17). Lung measurements were performed with standard spirometry and new methods: airspace dimension assessment (AiDA), oscillometry, blood serum biomarkers (club cell secretory protein 16, surfactant protein D, matrix metalloproteinases, fibroblast, hepatocyte growth factor, interleukins), and one urine biomarker (desmosine). RESULTS: According to spirometry measurements, all participants had normal lung function. However, prevalence of cough was significantly higher among welders compared with controls and lung changes were found in welders with the novel methods. Welders had significantly higher respiratory system resistance assessed with oscillometry, serum levels of metalloproteinases 9 and hepatocyte growth factor, compared with controls. Airspace dimensions were on average higher among welders compared with controls, but the difference was not significant. The number of welding years correlated with decreased respiratory system reactance and increased serum levels of matrix metalloproteinases 9, interleukin 6, and hepatocyte growth factor. Airspace dimension assessment indices were correlated with increasing levels of inflammatory markers and matrix metalloproteinases. CONCLUSIONS: This study indicated the potential to use new and more sensitive methods for identification of changes in lungs when standard spirometry failed to do so.

Uncovering the cytotoxic effects of air pollution with multi-modal imaging of in vitro respiratory models.

Annually, an estimated seven million deaths are linked to exposure to airborne pollutants. Despite extensive epidemiological evidence supporting clear associations between poor air quality and a range of short- and long-term health effects, there are considerable gaps in our understanding of the specific mechanisms by which pollutant exposure induces adverse biological responses at the cellular and tissue levels. The development of more complex, predictive, in vitro respiratory models, including two- and three-dimensional cell cultures, spheroids, organoids and tissue cultures, along with more realistic aerosol exposure systems, offers new opportunities to investigate the cytotoxic effects of airborne particulates under controlled laboratory conditions. Parallel advances in high-resolution microscopy have resulted in a range of in vitro imaging tools capable of visualizing and analysing biological systems across unprecedented scales of length, time and complexity. This article considers state-of-the-art in vitro respiratory models and aerosol exposure systems and how they can be interrogated using high-resolution microscopy techniques to investigate cell-pollutant interactions, from the uptake and trafficking of particles to structural and functional modification of subcellular organelles and cells. These data can provide a mechanistic basis from which to advance our understanding of the health effects of airborne particulate pollution and develop improved mitigation measures.

Size-resolved characterization of particles >10 nm emitted to air during metal recycling.

BACKGROUND: In the strive towards a circular economy, metal waste recycling is a growing industry. During the recycling process, particulate matter containing toxic and allergenic metals will be emitted to the air causing unintentional exposure to humans and environment. OBJECTIVE: In this study detailed characterization of particle emissions and workplace exposures were performed, covering the full size range from 10 nm to 10 µm, during recycling of three different material flows: Waste of electrical and electronic equipment (WEEE), metal scrap, and cables. METHODS: Both direct-reading instruments (minute resolution), and time-integrated filter measurements for gravimetric and chemical analysis were used. Additionally, optical sensors were applied and evaluated for long-term online monitoring of air quality in industrial settings. RESULTS: The highest concentrations, in all particle sizes, and with respect both to particle mass and number, were measured in the WEEE flow, followed by the metal scrap flow. The number fraction of nanoparticles was high for all material flows (0.66-0.86). The most abundant metals were Fe, Al, Zn, Pb and Cu. Other elements of toxicological interest were Mn, Ba and Co. SIGNIFICANCE: The large fraction of nanoparticles, and the fact that their chemical composition deviate from that of the coarse particles, raises questions that needs to be further addressed including toxicological implications, both for humans and for the environment.

Missed Evaporation from Atmospherically Relevant Inorganic Mixtures Confounds Experimental Aerosol Studies.

Sea salt aerosol particles are highly abundant in the atmosphere and play important roles in the global radiative balance. After influence from continental air, they are typically composed of Na+, Cl-, NH4+, and SO42- and organics. Analogous particle systems are often studied in laboratory settings by atomizing and drying particles from a solution. Here, we present evidence that such laboratory studies may be consistently biased in that they neglect losses of solutes to the gas phase. We present experimental evidence from a hygroscopic tandem differential mobility analyzer and an aerosol mass spectrometer, further supported by thermodynamic modeling. We show that, at normally prevailing laboratory aerosol mass concentrations, for mixtures of NaCl and (NH4)2SO4, a significant portion of the Cl- and NH4+ ions are lost to the gas phase, in some cases, leaving mainly Na2SO4 in the dry particles. Not considering losses of solutes to the gas phase during experimental studies will likely result in misinterpretation of the data. One example of such data is that from particle water uptake experiments. This may bias the explanatory models constructed from the data and introduce errors inte predictions made by air quality or climate models.

Quantifying the influence of urban biotic and abiotic environmental factors on great tit nestling physiology.

There is a long history of avian studies investigating the impacts of urbanization. While differences in several life-history traits have been documented, either between urban and rural populations or across generalized urbanization gradients, a detailed understanding of which specific environmental variables cause these phenotypic differences is still lacking. Here, we quantified several local environmental variables coupled to urbanization (air pollution, tree composition, ambient temperature, and artificial light at night [ALAN]) within territories of breeding great tits (Parus major). We linked the environmental variables to physiological measures of the nestlings (circulating fatty acid composition [FA], antioxidant capacity and an oxidative damage marker [malondialdehyde; MDA]), to garner a mechanistic understanding of the impact of urbanization. We found that the antioxidant capacity of nestlings decreased with higher numbers of oak trees and levels of PM2.5 (airborne particulate matter with a diameter < 2.5 µm). Furthermore, the ratio of ω6:ω3 polyunsaturated FAs, important for immune function, was positively correlated with PM2.5 concentration, while being negatively associated with ambient temperature and number of non-native trees in the territory. Body mass and wing length both increased with the number of local oak trees. We also show, through a principal component analysis, that while the environmental variables fall into an urbanization gradient, this gradient is insufficient to explain the observed physiological responses. Therefore, accounting for individual environmental variables in parallel, and thus allowing for interactions between these, is crucial to fully understand the urban ecosystem.

Airspace Dimension Assessment with Nanoparticles (AiDA) in Comparison to Established Pulmonary Function Tests.

Background: Airspace Dimensions Assessment with nanoparticles (AiDA) is a new method for non-invasive measurement of pulmonary distal airspaces. The aim of this study was to compare AiDA measurements with other pulmonary function variables to better understand the potential of AiDA in a clinical context. Methods: AiDA measurements and pulmonary function tests were performed in 695 subjects as part of the Swedish CArdioPulmonary bioImage Study. The measurement protocol included spirometry, measurement of diffusing capacity of carbon monoxide, oscillometry and pulmonary computed tomography. AiDA indices were compared to all other pulmonary examination measurements using multivariate statistical analysis. Results: Our results show that AiDA measurements were significantly correlated with other pulmonary function examination indices, although covariance was low. We found that AiDA variables explained variance in the data that other lung function variables only influenced to a minor extent. Conclusion: We conclude that the AiDA method provides information about the lung that is inaccessible with more conventional lung function techniques.

A controlled chamber study of effects of exposure to diesel exhaust particles and noise on heart rate variability and endothelial function.

BACKGROUND: Adverse cardiovascular effects are associated with both diesel exhaust and road traffic noise, but these exposures are hard to disentangle epidemiologically. We used an experimental setup to evaluate the impact of diesel exhaust particles and traffic noise, alone and combined, on intermediary outcomes related to the autonomic nervous system and increased cardiovascular risk. METHODS: In a controlled chamber 18 healthy adults were exposed to four scenarios in a randomized cross-over fashion. Each exposure scenario consisted of either filtered (clean) air or diesel engine exhaust (particle mass concentrations around 300 µg/m3), and either low (46 dB(A)) or high (75 dB(A)) levels of traffic noise for 3 h at rest. ECG was recorded for 10-min periods before and during each exposure type, and frequency-domain heart rate variability (HRV) computed. Endothelial dysfunction and arterial stiffness were assessed after each exposure using EndoPAT 2000. RESULTS: Compared to control exposure, HRV in the high frequency band decreased during exposure to diesel exhaust, both alone and combined with noise, but not during noise exposure only. These differences were more pronounced in women. We observed no synergistic effects of combined exposure, and no significant differences between exposure scenarios for other HRV indices, endothelial function or arterial stiffness. CONCLUSION: Three-hour exposure to diesel exhaust, but not noise, was associated with decreased HRV in the high frequency band. This indicates activation of irritant receptor-mediated autonomic reflexes, a possible mechanism for the cardiovascular risks of diesel exposure. There was no effect on endothelial dysfunction or arterial stiffness after exposure.

Toxicological effects of zinc oxide nanoparticle exposure: an in vitro comparison between dry aerosol air-liquid interface and submerged exposure systems.

Engineered nanomaterials (ENMs) are increasingly produced and used today, but health risks due to their occupational airborne exposure are incompletely understood. Traditionally, nanoparticle (NP) toxicity is tested by introducing NPs to cells through suspension in the growth media, but this does not mimic respiratory exposures. Different methods to introduce aerosolized NPs to cells cultured at the air-liquid-interface (ALI) have been developed, but require specialized equipment and are associated with higher cost and time. Therefore, it is important to determine whether aerosolized setups induce different cellular responses to NPs than traditional ones, which could provide new insights into toxicological responses of NP exposure. This study evaluates the response of human alveolar epithelial cells (A549) to zinc oxide (ZnO) NPs after dry aerosol exposure in the Nano Aerosol Chamber for In Vitro Toxicity (NACIVT) system as compared to conventional, suspension-based exposure: cells at ALI or submerged. Similar to other studies using nebulization of ZnO NPs, we found that dry aerosol exposure of ZnO NPs via the NACIVT system induced different cellular responses as compared to conventional methods. ZnO NPs delivered at 1.0 µg/cm2 in the NACIVT system, mimicking occupational exposure, induced significant increases in metabolic activity and release of the cytokines IL-8 and MCP-1, but no differences were observed using traditional exposures. While factors associated with the method of exposure, such as differing NP aggregation, may contribute toward the different cellular responses observed, our results further encourage the use of more physiologically realistic exposure systems for evaluating airborne ENM toxicity.

Release of carbon nanotubes during combustion of polymer nanocomposites in a pilot-scale facility for waste incineration.

Nanocomposites, formed by incorporating nanoparticles into a matrix of standard materials, are increasing on the market. Little focus has been directed towards safe disposal and recycling of these new materials even though the disposal has been identified as a phase of the products' life cycle with a high risk of uncontrolled emissions of nanomaterials. In this study, we investigate if the carbon nanotubes (CNTs), when used as a filler in two types of polymers, are fully destructed in a pilot-scale combustion unit designed to mimic the combustion under waste incineration. The two polymer nanocomposites studied, polycarbonate (PC) with CNT and high-density polyethylene (HDPE) with CNT, were incinerated at two temperatures where the lower temperature just about fulfilled the European waste incineration directive while the upper was chosen to be on the safe side of fulfilling the directive. Particles in the flue gas were sampled and analysed with online and offline instrumentation along with samples of the bottom ash. CNTs could be identified in the flue gas in all experiments, although present to a greater extent when the CNTs were introduced in PC as compared to in HDPE. In the case of using PC as polymer matrix, CNTs were identified in 3-10% of the analysed SEM images while for HDPE in only ~0.5% of the images. In the case of PC, the presence of CNTs decreased with increasing bed temperature (from 10% to 3% of the images). The CNTs identified were always in bundles, often coated with remnants of the polymer, forming particles of ~1-4 µm in diameter. No CNTs were identified in the bottom ash, likely explained by the difference in time when the bottom ash and fly ash are exposed to high temperatures (~hours compared to seconds) in the pilot facility. The results suggest that the residence time of the fly ash in the combustion zone is not long enough to allow full oxidation of the CNTs. Thus, the current regulation on waste incineration (requiring a residence time of the flue gas >850 °C during at least 2 s) may not be enough to obtain complete destruction of CNTs in polymer composites. Since several types of CNTs are known to be toxic, we stress the need for further investigation of the fate and toxicity of CNTs in waste treatment processes.

Bimetallic Nanoparticles as a Model System for an Industrial NiMo Catalyst.

An in-depth understanding of the reaction mechanism is required for the further development of Mo-based catalysts for biobased feedstocks. However, fundamental studies of industrial catalysts are challenging, and simplified systems are often used without direct comparison to their industrial counterparts. Here, we report on size-selected bimetallic NiMo nanoparticles as a candidate for a model catalyst that is directly compared to the industrial system to evaluate their industrial relevance. Both the nanoparticles and industrial supported NiMo catalysts were characterized using surface- and bulk-sensitive techniques. We found that the active Ni and Mo metals in the industrial catalyst are well dispersed and well mixed on the support, and that the interaction between Ni and Mo promotes the reduction of the Mo oxide. We successfully produced 25 nm NiMo alloyed nanoparticles with a narrow size distribution. Characterization of the nanoparticles showed that they have a metallic core with a native oxide shell with a high potential for use as a model system for fundamental studies of hydrotreating catalysts for biobased feedstocks.

Correction: Schavkan, A., et al. Number Concentration of Gold Nanoparticles in Suspension: SAXS and spICPMS as Traceable Methods Compared to Laboratory Methods. Nanomaterials 2019, 9, 502.

The authors wish to make the following corrections to this paper [...].

Number Concentration of Gold Nanoparticles in Suspension: SAXS and spICPMS as Traceable Methods Compared to Laboratory Methods.

The industrial exploitation of high value nanoparticles is in need of robust measurement methods to increase the control over product manufacturing and to implement quality assurance. InNanoPart, a European metrology project responded to these needs by developing methods for the measurement of particle size, concentration, agglomeration, surface chemistry and shell thickness. This paper illustrates the advancements this project produced for the traceable measurement of nanoparticle number concentration in liquids through small angle X-ray scattering (SAXS) and single particle inductively coupled plasma mass spectrometry (spICPMS). It also details the validation of a range of laboratory methods, including particle tracking analysis (PTA), dynamic light scattering (DLS), differential centrifugal sedimentation (DCS), ultraviolet visible spectroscopy (UV-vis) and electrospray-differential mobility analysis with a condensation particle counter (ES-DMA-CPC). We used a set of spherical gold nanoparticles with nominal diameters between 10 nm and 100 nm and discuss the results from the various techniques along with the associated uncertainty budgets.

Sticky Measurement Problem: Number Concentration of Agglomerated Nanoparticles.

Measuring the number concentration of colloidal nanoparticles (NPs) is critical for assessing reproducibility, enabling compliance with regulation, and performing risk assessments of NP-enabled products. For nanomedicines, their number concentration directly relates to their dose. However, the lack of relevant reference materials and established traceable measurement approaches make the validation of methods for NP number concentration difficult. Furthermore, commercial products often exhibit agglomeration, but guidelines for dealing with nonideal samples are scarce. We have compared the performance of five benchtop measurement methods for the measurement of colloidal number concentration in the presence of different levels of agglomeration. The methods are UV-visible spectroscopy, differential centrifugal sedimentation, dynamic light scattering, particle tracking analysis, and single-particle inductively coupled plasma mass spectrometry. We find that both ensemble and particle-by-particle methods are in close agreement for monodisperse NP samples and three methods are within 20% agreement for agglomerated samples. We discuss the sources of measurement uncertainties, including how particle agglomeration affects measurement results. This work is a first step toward validation and expansion of the toolbox of methods available for the measurement of real-world NP products.