ABSTRACT
The persistent use of pesticides in the agriculture field remains a serious issue related to public health. In the present work, molecularly imprinted polymer thin films were developed using electropolymerization of pyrrole (py) onto gold microelectrodes followed by electrodeposition for the selective detection of chlorpyrifos (CPF). The molecularly imprinted polymer (MIP) was synthesized by the electrochemical deposition method, which allowed in-line transfer of MIP on gold microelectrodes without using any additional adhering agents. Various parameters such as pH, monomer ratio, scan rate, and deposition cycle were optimized for sensor fabrication. The sensor was characterized at every stage of fabrication using various spectroscopic, microscopic, and electrochemical techniques. The sensor requires only 2 µL of the analyte and its linear detection range was found to be 1 µM to 1 fM. The developed sensor's limit of detection (LOD) and limit of quantification (LOQ) were found to be 0.93 and 2.82 fM, respectively, with a sensitivity of 3.98 (µA/(µM)/ mm2. The sensor's shelf life was tested for 70 days. The applicability of the sensor in detecting CPF in fruit and vegetable samples was also assessed out with recovery % between 91 and 97% (RSD < 5%). The developed sensor possesses a huge commercial potential for on-field monitoring of pesticides.
ABSTRACT
Graphene quantum dots (GQDs) possess excellent optical and electrical properties that can be used in a wide variety of application. Synthesis of hybrid nanoparticles with GQDs have been known to improve the properties further. Therefore, in this method, graphene quantum dots -gold (GQD-Au) hybrid nanoparticles were synthesized using GQDs which reduces HAuCl4.3H2O to Au nanoparticles on its surface at room temperature. The GQDs with self-passivated layers were synthesized by microwave assisted hydrothermal method using glucose as a single precursor. The synthesis process does not involve the use of harmful chemicals. The whole synthesis process of GQD and GQD-Au hybrid nanoparticles takes only five minutes. The synthesized GQDs have been extracted using citrate in order to increase the stability of the hybrid nanoparticles for up to four weeks. The size of the synthesized GQD-Au hybrid nanoparticles is in the range of 5-100 nm and were found to be luminescent under UV-A illumination. The merit of the following method over other synthesis techniques include its rapidity, ease of preparation, and no requirement of elaborate synthesis procedures and/or harmful chemicals. The GQD-Au hybrid nanoparticles can be used in several applications such as luminescent coatings for glass and windowpanes for automobiles, etc. The reducing property of GQDs can further be utilized for the reduction of various metal salts (AgNO3) and organic dyes (methylene blue and methyl orange). . It presents a method/protocol-development of the luminescent GQD-Au hybrid particles of size ~ 5-100 nm. . The GQD-Au hybrid particles find potential applications in luminescent coating applications.
ABSTRACT
We report an investigation into the magnetic and electronic properties of partially hydrogenated vertically aligned few layers graphene (FLG) synthesized by microwave plasma enhanced chemical vapor deposition. The FLG samples are hydrogenated at different substrate temperatures to alter the degree of hydrogenation and their depth profile. The unique morphology of the structure gives rise to a unique geometry in which graphane/graphone is supported by graphene layers in the bulk, which is very different from other widely studied structures such as one-dimensional nanoribbons. Synchrotron based x-ray absorption fine structure spectroscopy measurements have been used to investigate the electronic structure and the underlying hydrogenation mechanism responsible for the magnetic properties. While ferromagnetic interactions seem to be predominant, the presence of antiferromagnetic interaction was also observed. Free spins available via the conversion of sp(2) to sp(3) hybridized structures, and the possibility of unpaired electrons from defects induced upon hydrogenation are thought to be likely mechanisms for the observed ferromagnetic orders.
ABSTRACT
Polymethylmethacrylate (PMMA) microfluidic devices have been fabricated using a hot embossing technique to incorporate micro-pillar features on the bottom wall of the device which when combined with either a plasma treatment or the coating of a diamond-like carbon (DLC) film presents a range of surface modification profiles. Experimental results presented in detail the surface modifications in the form of distinct changes in the static water contact angle across a range from 44.3 to 81.2 when compared to pristine PMMA surfaces. Additionally, capillary flow of water (dyed to aid visualization) through the microfluidic devices was recorded and analyzed to provide comparison data between filling time of a microfluidic chamber and surface modification characteristics, including the effects of surface energy and surface roughness on the microfluidic flow. We have experimentally demonstrated that fluid flow and thus filling time for the microfluidic device was significantly faster for the device with surface modifications that resulted in a lower static contact angle, and also that the incorporation of micro-pillars into a fluidic device increases the filling time when compared to comparative devices.