ABSTRACT
This paper presents research results in the field of industrial die forging, mostly related to the use of advanced measuring techniques and tools, numerical simulations, and other IT tools and methods for a geometrical analysis of the forged items as well as detection of forging flaws and their prevention, and optimization of the hot-forging processes. The results of the conducted investigations were divided into three main areas. The first area refers to the application of, e.g., optical scanners and programs related to their operation, data analysis, including the construction of virtual gauges, measurements of selected geometrical features of both the manufactured forgings and their physical and virtual models, as well as an analysis of the durability of the forging tools based on the proprietary reverse scanning method. The second area presents the results of measurements and analyses performed with the use of finite element modeling and by means of some special functions in the calculation packages, such as contact, flow lines, trap, or fold, for the detection of forging defects and an analysis of the force parameters. In turn, the third area presents a combination of different methods of measurement and analysis, both FEM and scanning, as well as other IT methods (physical modeling, image analysis, etc.) for the analysis of the geometry and defects of the forgings. The presented results point to the great potential of these types of tools and techniques in forging industry applications as they significantly shorten the time and increase the accuracy of the measurement, as well as providing a lot of valuable information, physical variables, and technological parameters that are difficult or impossible to determine either analytically or through experimental means. The use and development of these techniques and methods are fully justified, both in the aspect of science and the increased effectiveness and efficiency of production.
ABSTRACT
This study performs a complex analysis and review of the currently applied methods of inductively heating the charge material in hot die forging processes, as well as elaborates and verifies a more effective heating method. On this basis, a device for inductive heating using variable frequency inductors was designed and constructed, which made it possible to reduce the scale and decarburization with respect to the heater used so far. In the first place, the temperature distributions in the heater in the function of time were modeled with the use of the CEDRAT FLUX software. The aim of the research was to analyze the temperature gradient and value diversification on the surface and in the material core, as well as to determine the process stability. The following stage was designing and constructing a heater with an automatic system of loading and positioning of the charge on the exit, as well as with a possibility of working in a fully automated system adjusted to the work center. The last stage of investigations was the verification of the elaborated effective heating method on the basis of a short production series and a continuous work for the period of 8 h, both in the quantitative and qualitative aspect (reduced oxidation and decarburization as well as a gradient between the core and the surface). The obtained results confirm the effectiveness of the proposed solution referring to heating the charge material, especially in the aspect of stability and repeatability of the process, as well as a significant reduction in oxidation and decarburization of the material surface.
ABSTRACT
The study performs a comparative analysis of the wear of tools made of two wear-resistant materials: steel Hardox 600 and NC11LV, used in the process of forming a band for roofing tiles. The analyses were to allow the assessment of the possibility of replacing the standard material for tools in this process with a much less expensive tool steel for cold work after heat treatment (with a large number of carbides), as an alternative material dedicated to tools resistant to intense abrasive wear. The performed investigations included a macroscopic and geometrical analysis with the use of 3D scanning, microstructural analyses conducted by means of a light microscope, as well as an analysis of the topography of the working areas of the tools with the use of SEM, and microhardness tests. The obtained results demonstrate that the tools made of both materials were characterized with a similar level of wear, which, in the most critical area, reached over 4 mm, while the tools made of steel NC11LV worked over a much longer period of time without regeneration, equaling 912 h, and an insert made of steel Hardox 600 operated for 384 h. A higher tool life in the case of NC11LV steel may be the result of higher hardness and the presence of hard carbides.
ABSTRACT
The global production of die forgings is an important branch of the motor industry for obvious reasons, resulting from the very good mechanical properties of the forged products. The expectations of the recipients, beside the implementation of the forging process, include also a range of supplementary procedures, such as finishing treatment including shot blasting, thermal treatment, and machining, in order to ensure the proper quality of the provided semi-product or the ready detail for the assembly line. Especially important in the aspect of the operational properties of the products is the thermal treatment of the forgings, which can be implemented in many variants, depending on the expected results. Unfortunately, a treatment of this type, realized separately after the forging process, is very time and energy-consuming; additionally, it significantly raises the production costs due to the increased energy consumption resulting from the necessity of repeated heating of the forgings for such thermal treatment. The article reviews the most frequently applied (separately, after the forging process) thermal treatments for die forgings together with the devices/lines assigned for them, as well as presents an alternative (thermoplastic) method of forging production with the use of the forging heat. The paper also presents a prototype semi-industrial controlled cooling line developed by the authors, which allows the development of the assumed heat treatment of forgings directly after forging with the use of forging heat, together with sample results of conducted tests.
ABSTRACT
This article proposes an indirect measurement method based on a dimensional and shape analysis of forgings for the evaluation of the manufacture and the proper operation of the key elements of the crank press, in which after modernization, a quick tool assembly based on SMED (Single Minute Exchange of Die) was implemented. As a result of the introduced changes aiming at improving the forging aggregate and increasing the production efficiency, errors were observed on the manufactured products-forgings in the form of twists and joggles. In order to solve the problem, a lot of advanced methods was used, including: dynamic system of deformation analysis, numerical modeling and as well as dimensional and shape analysis by 3d scanning. Despite the above, this approach (classic way) did not solve the problem. A proprietary method with the use of 3D reverse scanning was proposed, which allows to solve the problem of forgings errors. Based on the measurement results and analyses for a few variants of production cycles, the necessary changes were obtained, making it possible to minimize the errors and obtain proper products in respect of geometry and quality.
