Antimicrobial Activity of Morphology-Controlled Cu2O Nanoparticles: Oxidation Stability under Humid and Thermal Conditions.

Metal oxides can be used as antimicrobial agents, especially since they can be fabricated into various forms such as films, masks, and filters. In particular, the durability of antimicrobial agents and the duration of their antimicrobial activity are important factors that determine their suitability for a specific purpose. These factors are related to the morphology and size of particles. The metal oxide Cu2O is often oxidized to CuO in various conditions, which reduces its antimicrobial activity. This study focused on the oxidation of nanoparticles of Cu2O with three morphologies, namely, spherical, octahedral, and cubic morphologies, in excessively humid and excessive-thermal environments for a specific duration and the antimicrobial activity of the NPs. Cu2O nanoparticles were prepared using the chemical reduction method, and their morphology could be varied by adjusting the molar ratio of OH- to Cu2+ and changing the reducing agent. It was found that cubic Cu2O was the most stable against oxidation and had the smallest reduction in antimicrobial activity. This study examined the antimicrobial activity and the oxidation stability of Cu2O NPs with different morphologies but similar particle sizes.

Effect of Various Acid Solutions on the CO2 Dissolution Rate, Morphology, and Particle Size of Precipitated Calcium Carbonate Synthesized Using Seashells.

In this study, the influence of acid solutions on the production of precipitated calcium carbonate (PCC) using seashells was investigated. In terms of the Ca dissolution efficiency and atmosphere for dissolving CO32-, the results indicate that HCl, HNO3, CH3COOH, and HCOOH at 1.0 M were the most ideal among the acid solutions. The use of weak acids resulted in the low degree of dissolution of Al and Fe. These impurities could be mostly removed through the pH adjustment process, leading to PCC with a purity of 99% or more. Further, CH3COOH and HCOOH exhibited low CaCO3 carbonation efficiency owing to the hydrogen bonding of the carboxyl group and its hindering effect on the growth of CaCO3 particles. In addition, in the presence of the carboxyl group, the morphology tended to be oval, and the particle size was small. Particularly, when CH3COOH was used, the combined effect of the low initial Ca ion concentration and slow CO2 dissolution rate resulted in minimal changes during the carbonation time and the smallest particle size. However, variations in the degree of Ca concentration with a change in the acid solution concentration influenced the dominance of nucleation and particle growth, leading to variations in the particle size. The results of this study revealed that when manufacturing PCC using seashells, the appropriate acid solution must be selected to obtain the required PCC properties.

Surface Oxidation of Cu2O Nanoparticles by Adsorbed Ammonia.

Copper-based nanoparticles have been intensively studied owing to their superior antibacterial activity. In this study, cuprous oxide (Cu2O) nanoparticles were synthesized using two different methods. In particular, two methods for synthesizing copper oxide from NaOH, namely, with and without the addition of NH3, were used to adjust the morphology of the nanoparticles. The nanoparticles from the NH3 and NaOH samples possessed an octahedral morphology. The crystal structure of the samples was confirmed by X-ray diffraction. The size distribution of the NH3 sample was narrower than that of the NaOH sample. Furthermore, the average size of the NH3 sample was smaller than that of the NaOH sample. Unexpectedly, the antibacterial activity of the NH3 sample was found to be lower than that of the NaOH sample. X-ray photoelectron spectroscopy and Fourier-transform infrared spectroscopy revealed that the adsorbed NH3 caused the surface oxidation of Cu2O nanoparticles with azide (N3) formation on surface.

Liquid Hydrogenation of Maleic Anhydride with Pd/C Catalyst at Low Pressure and Temperature in Batch Reactor.

Succinic acid (SA) produced from hydrogenation of maleic anhydride (MAN) is used widely in manufacturing of pharmaceuticals, agrochemicals, surfactants and detergent, green solvent and biodegradable plastic. In this study, we performed that liquid hydrogenation of MAN to SA with 5 wt% Pd supported on activated carbon (Pd/C) at low pressure and temperature. The synthesis of SA was performed in aqueous solution while varying temperature, pressure, catalytic amount and agitation speed. We confirmed that the composition of the products consisting of SA, maleic acid (MA), fumaric acid (FA) and malic acid (MLA) depends on the process. The catalytic characteristics were analyzed by TGA, TEM.

Synthesis of Glycerol Carbonate by Transesterification of Glycerol with Urea Over Zn/Al Mixed Oxide.

Reactions of glycerol carbonate using glycerol and urea have been carried out previously using ZnSO4 and ZnO catalysts, and high yields have been reported using ZnSO4 as catalyst. However, this salt is soluble in glycerol, and recycling of catalyst is difficult after the reaction. In this study, we prepared a mixed metal oxide catalyst using Zn and Al, and this catalyst consisted of a mixture of ZnO and ZnAl2O4. We confirmed the conversion of glycerol and the yield of glycerol carbonate of the amount of Al. As a result, we obtained a yield of 82.3% and a conversion of 82.7%. In addition we obtained high yield in recycling of catalyst. The yield of the glycerol carbonate increases with an increase of acid and base site of catalysts and the highest catalytic activity was obtained when acid/base ratio was approx. 1. From this result, we may conclude that the acid and base site density and ratio of catalysts were very important parameters in the synthesis of glycerol carbonate from urea and glycerol.

Hydrogenolysis of Glycerol to Propylene Glycol on Nanosized Cu-Zn-Al Catalysts Prepared Using Microwave Process.

Cu-Zn-Al catalysts were prepared using microwave-assisted process and co-precipitation methods. The prepared catalysts were characterized by XRD, BET, XPS and TPD of ammonia and their catalytic activity for the hydrogenolysis of glycerol to propylene glycol was also examined. The XRD patterns of Cu/Zn/Al mixed catalysts show CuO and ZnO crystalline phase regardless of preparation method. The highest glycerol hydrogenolysis conversion is obtained with the catalyst having a Cu/Zn/Al ratio of 2:2:1. Hydrogen pre-reduction of catalysts significantly enhanced both glycerol conversions and selectivity to propylene glycol. The glycerol conversion increased with an increase of reaction temperature. However, the selectivity to propylene glycol increased with an increase of temperature, and then declined to 30.5% at 523 K.

Carbon Nano Tube Supported Pd Catalyst: Effect of Support Textual Properties with Pre-Treatment Method of Pd Particle.

The aim of this work is to be compared the effect of supports textural properties with pre-treatment method on dispersion of Pd particle. The CNTs were functionalized by different concentration of acid in order to obtain materials with different chemical and physical properties. The characteristics of functionalized CNTs were investigated by FT-IR and Rama spectropy. The Pd/CNTs catalysts prepared on support having the different surface properties were characterized by XRD, FE-TEM and CO-chemisorption. When pretreated 8M concentration, the CNTs has the highest amount of oxygen functional group and ID/IG ratio, in this study. Pd/CNT8M has high dispersion and small particle size. From these results, we confirmed that characteristics of Pd/CNTs catalyst such as particle size and dispersion of Pd are influenced by density of oxygen functional group and disorder of CNTs. And we have observed that acid treatment concentration of 8M is sufficient to functionalize the CNTs by introducing -COOH group of CNTs surfaces.

Surfactant effects on SF6 hydrate formation.

Sulfur hexafluoride (SF(6)) has been widely used in a variety of industrial processes, but it is one of the most potent greenhouse gases. For this reason, it is necessary to separate or collect it from waste gas streams. One separation method is through hydrate crystal formation. In this study, SF(6) hydrate was formed in aqueous surfactant solutions of 0.00, 0.01, 0.05, 0.15 and 0.20 wt% to investigate the effects of surfactants on the hydrate formation rates. Three surfactants, Tween 20 (Tween), sodium dodecyl sulfate (SDS) and linear alkyl benzene sulfonate (LABS), were tested in a semi-batch stirred vessel at the constant temperature and pressures of 276.2 K and 0.78 MPa, respectively. All surfactants showed kinetic promoter behavior for SF(6) hydrate formation. It was also found that SF(6) hydrate formation proceeded in two stages with the second stage being the most rapid. In situ Raman spectroscopy analysis revealed that the increased gas consumption rate with the addition of surfactant was possibly due to the increased gas filling rate in the hydrate cavity.