Photo-Cross-Linked Fullerene-Based Hole Transport Material for Moisture-Resistant Regular Fullerene Sandwich Perovskite Solar Cells.

Despite the high efficiencies currently achieved with perovskite solar cells (PSCs), the need to develop stable devices, particularly in humid conditions, still remains. This study presents the synthesis of a novel photo-cross-linkable fullerene-based hole transport material named FT12. For the first time, the photo-cross-linking process is applied to PSCs, resulting in the preparation of photo-cross-linked FT12 (PCL FT12). Regular PSCs based on C60-sandwich architectures were fabricated using FT12 and PCL FT12 as dopant-free hole transport layers (HTLs) and compared to the reference spiro-OMeTAD. The photovoltaic results demonstrate that both FT12 and PCL FT12 significantly outperform pristine spiro-OMeTAD regarding device performance and stability. The comparison between devices based on FT12 and PCL FT12 demonstrates that the photo-cross-linking process enhances device efficiency. This improvement is primarily attributed to enhanced charge extraction, partial oxidation of the HTL, increased hole mobility, and improved layer morphology. PCL FT12-based devices exhibit improved stability compared to FT12 devices, primarily due to the superior moisture resistance achieved through photo-cross-linking.

CPE-Na-Based Hole Transport Layers for Improving the Stability in Nonfullerene Organic Solar Cells: A Comprehensive Study.

Organic photovoltaic (OPV) cells have experienced significant development in the last decades after the introduction of nonfullerene acceptor molecules with top power conversion efficiencies reported over 19% and considerable versatility, for example, with application in transparent/semitransparent and flexible photovoltaics. Yet, the optimization of the operational stability continues to be a challenge. This study presents a comprehensive investigation of the use of a conjugated polyelectrolyte polymer (CPE-Na) as a hole layer (HTL) to improve the performance and longevity of OPV cells. Two different fabrication approaches were adopted: integrating CPE-Na with PEDOT:PSS to create a composite HTL and using CPE-Na as a stand-alone bilayer deposited beneath PEDOT:PSS on the ITO substrate. These configurations were compared against a reference device employing PEDOT:PSS alone, as the HTL increased efficiency and fill factor. The instruments with CPE-Na also demonstrated increased stability in the dark and under simulated operational conditions. Device-based PEDOT:PSS as an HTL reached T80 after 2500 h while involving CPE-Na in the device kept at T90 in the same period, evidenced by a reduced degradation rate. Furthermore, the impedance spectroscopy and photoinduced transient methods suggest optimized charge transfer and reduced charge carrier recombination. These findings collectively highlight the potential of CPE-Na as a HTL optimizer material for nonfluorine OPV cells.

Monodentate versus Bidentate Anchoring Groups in Self-Assembling Molecules (SAMs) for Robust p-i-n Perovskite Solar Cells.

Current improvement in perovskite solar cells (PSCs) has been achieved by interface engineering and fine-tuning of charge-selective contacts. In this work, we report three novel molecules that can form self-assembled layers (SAMs) as an alternative to the most commonly used p-type contact material, PTAA. Two of these molecules have bidentate anchoring groups (MC-54 and MC-55), while the last one is monodentate (MC-45). Besides the PTAA comparison, we also compared those two types of molecules and their effect on the solar cell's performance. Devices fabricated with MC-54 and MC-55 showed a remarkable field factor (about 80%) and a better current density, leading to higher efficient solar cells in comparison to MC-45 and PTAA. Moreover, mono- and bidentate present higher stability and reproducibility in comparison to PTAA.

p-Type Functionalized Carbon Nanohorns and Nanotubes in Perovskite Solar Cells.

The incorporation of p-type functionalized carbon nanohorns (CNHs) in perovskite solar cells (PSCs) and their comparison with p-type functionalized single- and double-walled carbon nanotubes (SWCNTs and DWCNTs) are reported in this study for the first time. These p-type functionalized carbon nanomaterial (CNM) derivatives were successfully synthesized by [2 + 1] cycloaddition reaction with nitrenes formed from triphenylamine (TPA) and 9-phenyl carbazole (Cz)-based azides, yielding CNHs-TPA, CNHs-Cz, SWCNTs-Cz, SWCNTs-TPA, DWCNTs-TPA, and DWCNTs-Cz. These six novel CNMs were incorporated into the spiro-OMeTAD-based hole transport layer (HTL) to evaluate their impact on regular mesoporous PSCs. The photovoltaic results indicate that all p-type functionalized CNMs significantly improve the power conversion efficiency (PCE), mainly by enhancing the short-circuit current density (Jsc) and fill factor (FF). TPA-functionalized derivatives increased the PCE by 12-17% compared to the control device without CNMs, while Cz-functionalized derivatives resulted in a PCE increase of 4-8%. Devices prepared with p-type functionalized CNHs exhibited a slightly better PCE compared with those based on SWCNTs and DWCNTs derivatives. The increase in hole mobility of spiro-OMeTAD, additional p-type doping, better energy alignment with the perovskite layer, and enhanced morphology and contact interface play important roles in enhancing the performance of the device. Furthermore, the incorporation of p-type functionalized CNMs into the spiro-OMeTAD layer increased device stability by improving the hydrophobicity of the layer and enhancing the hole transport across the MAPI/spiro-OMeTAD interface. After 28 days under ambient conditions and darkness, TPA-functionalized CNMs maintained the performance of the device by over 90%, while Cz-functionalized CNMs preserved it between 75 and 85%.

Novel Spiro-Core Dopant-Free Hole Transporting Material for Planar Inverted Perovskite Solar Cells.

Hole-transporting materials (HTMs) have demonstrated their crucial role in promoting charge extraction, interface recombination, and device stability in perovskite solar cells (PSCs). Herein, we present the synthesis of a novel dopant-free spiro-type fluorine core-based HTM with four ethoxytriisopropylsilane groups (Syl-SC) for inverted planar perovskite solar cells (iPSCs). The thickness of the Syl-SC influences the performance of iPSCs. The best-performing iPSC is achieved with a 0.8 mg/mL Syl-SC solution (ca. 15 nm thick) and exhibits a power conversion efficiency (PCE) of 15.77%, with Jsc = 20.00 mA/cm2, Voc = 1.006 V, and FF = 80.10%. As compared to devices based on PEDOT:PSS, the iPSCs based on Syl-SC exhibit a higher Voc, leading to a higher PCE. Additionally, it has been found that Syl-SC can more effectively suppress charge interfacial recombination in comparison to PEDOT:PSS, which results in an improvement in fill factor. Therefore, Syl-SC, a facilely processed and efficient hole-transporting material, presents a promising cost-effective alternative for inverted perovskite solar cells.

Subphthalocyanine-Diketopyrrolopyrrole Conjugates: 3D Star-Shaped Systems as Non-Fullerene Acceptors in Polymer Solar Cells with High Open-Circuit Voltage.

Invited for this month's cover are the collaborating groups of Prof. Ángela Sastre-Santos, Universidad Miguel Hernández, Prof. Lluis F. Marsal, Universitat Rovira i Virgili and Prof. Tomás Torres, Universidad Autónoma de Madrid, Spain. The cover shows a toy doll holding an umbrella which represents a non-planar, highly conjugated subphthalocyanine-diketopyrrolopyrrole hybrid molecule for non-fullerene organic solar cells. When the sun shines on the umbrella, it absorbs the light, and the doll slides down a polymeric flexible solar cell like a slide, where electrons are produced and electricity flows into the magic wand to illuminate the room. More information can be found in the Full Paper by Ángela Sastre-Santos, Lluis F. Marsal, Tomás Torres, and co-workers.

Subphthalocyanine-Diketopyrrolopyrrole Conjugates: 3D Star-Shaped Systems as Non-Fullerene Acceptors in Polymer Solar Cells with High Open-Circuit Voltage.

Four star-shaped electron acceptors (C1 -OPh, C3 -OPh, C1 -Cl and C3 -Cl) based on a subphthalocyanine core bearing three diketopyrrolopyrrole wings linked by an acetylene bridge have been synthesized. These derivatives feature two different axial substituents (i. e., 4-tert-butylphenoxy (OPh) or chlorine (Cl)) and for each of them, both the C1 and the C3 regioisomers have been investigated. The four compounds exhibit a broad absorption band in the 450-700 nm region, with bandgap values near to 2 eV. These materials were applied in the active layer of inverted bulk-heterojunction polymer solar cells in combination with the donor polymer PBDB-T. Derivatives bearing the OPh axial group showed the best performances, with C1 -OPh being the most promising with a PCE of 3.27 % and a Voc as high as 1.17 V. Despite presenting the widest absorption range, the photovoltaic results obtained with C1 -Cl turned out to be the lowest (PCE=1.01 %).

Fluorinated Zinc and Copper Phthalocyanines as Efficient Third Components in Ternary Bulk Heterojunction Solar Cells.

Fluorinated zinc and copper metallophthalocyanines MPcF48 are synthesized and incorporated as third component small molecules in ternary organic solar cells (TOSCs). To enable the high performance of TOSCs, maximizing short-circuit current density (J SC) is crucial. Ternary bulk heterojunction blends, consisting of a polymer donor PTB7-Th, fullerene acceptors PC70BM, and a third component MPcF48, are formulated to fabricate TOSCs with a device architecture of ITO/PFN/active layer/V2O5/Ag. Employing copper as metal atom substitution in the third component of TOSCs enhances J SC as a result of complementary absorption spectra in the near-infrared region. In combination with J SC enhancement, suppressed charge recombination, improved exciton dissociation and charge carrier collection efficiency, and better morphology lead to a slightly improved fill factor (FF), resulting in a 7% enhancement of PCE than those of binary OSCs. In addition to the increased PCE, the photostability of TOSCs has also been improved by the appropriate addition of CuPcF48. Detailed studies imply that metal atom substitution in phthalocyanines is an effective way to improve J SC, FF, and thus the performance and photostability of TOSCs.

Impact of inkjet printed ZnO electron transport layer on the characteristics of polymer solar cells.

In this paper, we demonstrate that zinc oxide (ZnO) layers deposited by inkjet printing (IJP) can be successfully applied to the low-temperature fabrication of efficient inverted polymer solar cells (i-PSCs). The effects of ZnO layers deposited by IJP as electron transport layer (ETL) on the performance of i-PSCs based on PTB7-Th:PC70BM active layers are investigated. The morphology of the ZnO-IJP layers was analysed by AFM, and compared to that of ZnO layers deposited by different techniques. The study shows that the morphology of the ZnO underlayer has a dramatic effect on the band structure and non-geminate recombination kinetics of the active layer deposited on top of it. Charge carrier and transient photovoltage measurements show that non-geminate recombination is governed by deep trap states in devices made from ZnO-IJP while trapping is less significant for other types of ZnO. The power conversion efficiency of the devices made from ZnO-IJP is mostly limited by their slightly lower J SC, resulting from non-optimum photon conversion efficiency in the visible part of the solar spectrum. Despite these minor limitations their J-V characteristics compare very favourably with that of devices made from ZnO layer deposited using different techniques.

Degradation Analysis of Encapsulated and Nonencapsulated TiO2/PTB7:PC70BM/V2O5 Solar Cells under Ambient Conditions via Impedance Spectroscopy.

Inverted organic cells are promising devices for sustainable and low-cost future electric generation. In this work, we present the degradation mechanisms studied in ITO/TiO2/PTB7:PC70BM/V2O5/Ag inverted organic solar cells (iOSCs) by impedance spectroscopy (IS). Measurements were performed on encapsulated (controlled environment) and nonencapsulated (ambient condition) cells following their temporal evolution under AM1.5 illumination for several voltage biases. From the impedance spectra, analyzed in terms of resistive/capacitive equivalent circuits, we were able to identify that the most sensitive layers inside of the device are contact layers. According with presented, IS technique is useful for determining the materials that have more influence on the degradation of organic solar cells. We demonstrate that IS is a powerful technique to identify the limiting mechanisms and to establish the limiting materials inside of the iOSCs.

Respuesta a "Paricalcitol en la enfermedad renal crónica en etapas anteriores a la diálisis" / Response to "Paricalcitol for pre-dialysis stages of chronic kidney disease"

No disponible

Prognosis of patients with unstable angina and low-risk exercise test: significance of ST-segment depression on the admission ECG.

The presence of ST-segment depression on the admission electrocardiogram (ECG) is an important predictor of poor outcome in patients with unstable angina. On the other hand, patients with unstable angina who undergo a low-risk exercise test are supposed to have a favorable prognosis. The objective of the study was to determine the prognostic significance of ST-segment depression on the admission ECG in patients with unstable angina who undergo an exercise test that indicates a low risk of events. An interpretable exercise test was performed in 257 patients with primary unstable angina. A low-risk exercise test was completed by 156 (60%) patients and medical therapy was planned for all these patients. A multivariate analysis was performed in order to determine the independent predictors of events (cardiac death, nonfatal acute myocardial infarction, or admission for unstable angina) during a 12-month follow-up. Among patients with a low-risk exercise test, there were no significant differences between patients with and without ST-segment depression on the presenting ECG with regard to event rate (34 vs. 29%, P=NS). In multivariate analysis, ST-segment depression was not related to a higher incidence of events. Our findings appear to indicate that the presence of ST-segment depression on the admission ECG loses its prognostic significance in patients with primary unstable angina if they complete a low-risk exercise test.

Tratamiento de la escoliosis idiopática con barra de Luque en (r)U con unión transversal y alambrado sublaminar / Idiophatic scoliosis treatment by U-Luque's rod as well transversal union and sublaminar wiring

Revisamos los resultados de la instrumentación segmentaria espinal con barra de Luque en "U" con unión transversal distal y alambrado sublaminar en 22 pacientes con escoliosis idiopática con edad promedio de 14.9 años al momento de la cirugía, con un seguimiento promedio de 3.9 años. La curva prequirúrgica promedio fue de 50§ y corregida a 28§ al momento de la cirugía y de 38§ en el último control radiográfico (24 por ciento), 15 tuvieron 10§ de pérdida de la corrección lograda y 3 presentaron un incremento de 5§ con respecto a la curva inicial, en 4 no hubo pérdida de la corrección. Ninguno presentó d,ficit neurológico, la fusión como principal propósito se logró en todos los casos. Nuestros resultados indican que la instrumentación segmentaria espinal con barra de Luque en "U" con unión transversal distal y alambrado sublaminar es una buena alternativa en cirujanos experimentados para el tratamiento de la escoliosis idiopática.