Low cost and easy acquisition: corn grain in microsurgery training.

OBJECTIVES: develop an easily accessible model for training the initial motor practice in microsurgery using corn kernels. METHODS: ten corn kernels (Zea mays) were used. A 7mm longitudinal cut was made on one side of the corn grain. The training consisted of performing 4 simple knots between the edges of the incision, using 10-0 mononylon thread. The parameters analyzed were 1) cost of the model; 2) assembly time of the model test system; 3) time for performing the knots; 4) distance between the knots. RESULTS: in all corn kernels tested, it was possible to perform the proposed microsurgical suture training, without any difficulty in the procedure. The average time to perform the 4 knots was 6.51±1.18 minutes. The total cost of the simulator model was R$3.59. The average distance between the knots was 1.7±0.3mm. The model developed from corn grains has an extremely low cost when compared to the use of animals or high-tech simulators. Other advantages are the easy availability of canned corn kernels and the possibility of making more than four knots along the 7mm incision. CONCLUSION: the training model developed has low cost, is easy to acquire and viable for training basic manual skills in microsurgery.

Low cost and easy acquisition: corn grain in microsurgery training / Baixo custo e fácil aquisição: grãos de milho no treinamento microcirúrgico

ABSTRACT Objectives: develop an easily accessible model for training the initial motor practice in microsurgery using corn kernels. Methods: ten corn kernels (Zea mays) were used. A 7mm longitudinal cut was made on one side of the corn grain. The training consisted of performing 4 simple knots between the edges of the incision, using 10-0 mononylon thread. The parameters analyzed were 1) cost of the model; 2) assembly time of the model test system; 3) time for performing the knots; 4) distance between the knots. Results: in all corn kernels tested, it was possible to perform the proposed microsurgical suture training, without any difficulty in the procedure. The average time to perform the 4 knots was 6.51±1.18 minutes. The total cost of the simulator model was R$3.59. The average distance between the knots was 1.7±0.3mm. The model developed from corn grains has an extremely low cost when compared to the use of animals or high-tech simulators. Other advantages are the easy availability of canned corn kernels and the possibility of making more than four knots along the 7mm incision. Conclusion: the training model developed has low cost, is easy to acquire and viable for training basic manual skills in microsurgery.

RESUMO Objetivo: desenvolver um modelo facilmente acessível para o treinamento da prática motora inicial em microcirurgia a partir da utilização de grãos de milho. Métodos: foram utilizados dez grãos de milho (Zea mays). Realizou-se um corte longitudinal de 7mm em uma das faces do grão de milho. O treinamento consistiu na realização de 4 pontos simples entre as bordas da incisão, utilizando fio de mononáilon 10-0. Os parâmetros analisados foram 1) custo do modelo; 2) tempo de montagem do sistema de teste do modelo; 3) tempo de realização dos nós; 4) distância entre os pontos. Resultados: em todos os grãos testados foi possível realizar o treinamento de sutura microcirúrgica proposto, sem dificuldade ao procedimento. O tempo médio para a realização dos 4 pontos foi de 6,51±1,18 minutos. O custo total do modelo simulatório foi de R$3,59. A distância média entre os pontos foi de 1,7±0,3mm. O modelo desenvolvido a partir de grãos de milhos apresenta custo extremamente baixo quando comparado ao uso de animais ou de simuladores de alta tecnologia. Outras vantagens são fácil disponibilidade de grãos de milho em conserva e possibilidade de serem realizados mais de quatro pontos ao longo da incisão de 7mm. Conclusão: o modelo de treinamento desenvolvido é de baixo custo, de fácil aquisição e viável para o treinamento de habilidades manuais básicas em microcirurgia.