Spectrophotometric assessment of the color stability of composite resins polished with different techniques.

This study aimed to use spectrophotometry to assess the color stability of composite resins polished with different polishing techniques and scanning electron microscopy (SEM) to evaluate the surface micromorphology of the specimens. In this in vitro experimental study, a total of 96 disc-shaped specimens were fabricated from microfilled (Renamel Microfill, shade SB3) and nanohybrid (Estelite Sigma Quick, shade BW) composite resins in bright white shades (n = 48). Each group was randomized into 1 control and 2 experimental subgroups (n = 16): no polishing (control), polishing with aluminum oxide discs (experimental), or polishing with diamond-impregnated spiral wheels (experimental). In each subgroup, half of the specimens were immersed in a coffee solution and the other half in a tea solution for 48 hours after finishing (control) or polishing (experimental). Spectrophotometry was used to measure the color of the specimens at baseline, after finishing, after polishing (experimental groups only), and after immersion in tea and coffee. The surface micromorphology of a randomly selected specimen from each subgroup was assessed under SEM. The color change (ΔE*) of the specimens between measurements was calculated and analyzed using 1-way, 2-way, and 3-way analyses of variance (ANOVAs) and the Tukey test. Both tea and coffee caused significant color change in the composite resin specimens, with specimens immersed in coffee undergoing significantly greater color change than those immersed in tea (P < 0.001; 2-way ANOVA). The nanohybrid composite specimens polished with polishing discs had a significantly greater color change than nanohybrid specimens polished with spiral wheels (P = 0.041). The Tukey test revealed that there was no overall significant difference between the 2 polishing techniques (P = 0.505), but both of these subgroups exhibited a significantly lower color change than the control group (P < 0.001). In general, SEM did not reveal substantial differences between the 2 polishing techniques, but specimens polished by spiral wheels appeared to have a smoother surface. All polished specimens demonstrated clinically acceptable mean color change values (ΔE* < 3.5). The type of coloring agent had a greater effect on color stability than either the polishing technique or type of composite resin, with coffee causing a greater color change than tea.

Effect of Root Dentin Pretreatment on Micro-Push-Out Bond Strength of Fiber Posts to Root Canal Dentin: Cold Atmospheric Argon Plasma (CAAP) and Ethylenediaminetetraacetic Acid (EDTA).

PURPOSE: Debonding from the root canal dentin is the most common failure mode of fiber posts. This study aimed to assess the effects of cold atmospheric argon plasma (CAAP) and ethylenediaminetetraacetic acid (EDTA) on micro-push-out bond strength of fiber posts to root canal dentin. MATERIALS AND METHODS: Forty maxillary canine teeth were decoronated, underwent endodontic treatment, and were stored in an incubator for 7 days. After post space preparation, the teeth were randomly divided into four groups for different surface treatments: (I) saline, (II) 17% EDTA, (III) CAAP, and (IV) 17% EDTA + CAAP. Fiber posts (Whitepost no. 2, FGM) were cemented into the root canals using Panavia F2.0 resin cement, and 1 mm-thick sections were made at the coronal, middle, and apical thirds of the roots. The samples underwent micro-push-out bond strength test. The mode of failure was also determined under a stereomicroscope. Data were analyzed using three-way ANOVA and Tukey's post hoc test (α = 0.05). The mode of failure data were analyzed using the chi-square test. RESULTS: The mean micro-push-out bond strength of fiber posts was not significantly different in the four groups (P > 0.05). However, the bond strength values in the coronal third were significantly higher than the corresponding values in the apical third (P=0.01). There was no significant difference in the modes of failure between the groups (P > 0.05). CONCLUSION: Application of CAAP alone or in combination with 17% EDTA could not successfully increase the bond strength of fiber posts to root canal dentin.

Restoration of a Nonvital Tooth with Fiber Reinforce Composite (Wallpapering Technique).

INTRODUCTION: Reconstruction of endodontically treated tooth (ETT) is one of the greatest challenges in dentistry. Clinical success of fiber reinforcement composite (FRC) restorations in ETT depends on many factors like remaining tooth structure, knowing advantages of adhesive dentistry besides its drawbacks, and the correct use of fibers in combination with resin composite. Case Report. This article presents a case in which fibers have been used in composite buildup in order to increase the toughness and strength of the ETT direct restoration. In addition, this technique does not require root canal enlargement to eliminate the risk of root perforation. Also, this one visit treatment can be helpful for patients that could not pay the cost of indirect restoration and/or have no time. CONCLUSION: It seems in selected patients with special considerations, FRC composite restoration is valid alternatives for indirect restoration.

Color Stability of Ceramic Veneers Cemented with Self-Adhesive Cements after Accelerated Aging.

OBJECTIVES: Color change of cements over time can be detected through translucent ceramic veneers, compromising the aesthetic appearance of restorations in the long-term. This study aimed to assess the color stability of ceramic laminate veneers cemented with self-adhesive resin cements after accelerated aging. MATERIALS AND METHODS: In this study, 21 IPS e.max ceramic discs, measuring 8mm in diameter and 0.7 mm in thickness, were fabricated and divided into three groups (n=7) for the application of Choice 2 total-etch light-cure resin cement, RelyX U200 dual-cure self-adhesive resin cement, and SpeedCEM self-cure self-adhesive resin cement. The ceramic discs in each group were cemented on the prepared facial surface of bovine teeth. The color parameters were assessed using a spectrophotometer. Subsequently, the samples were subjected to accelerated aging for 100 hours, and the color parameters were measured again. The data were analyzed using two-way repeated-measures analysis of variance (ANOVA) and Tamhane's post-hoc test (P<0.05). RESULTS: Aging significantly affected the ceramic laminate color parameters in all three groups (P<0.05). SpeedCEM cement showed the lowest color stability (ΔE=4.2) after aging, and its color change was clinically unacceptable (ΔE>3.5). The color change of the other two groups was clinically acceptable (1<ΔE<3.5). CONCLUSION: The self-adhesive dual-cure cement showed color stability comparable to that of the total-etch light-cure cement for cementation of IPS e.max ceramic laminates. The color stability of both cements was superior to that of the self-adhesive self-cure cement.