ABSTRACT
Nanocrystal micro/nanoarrays with multiplexed functionalities are of broad interest in the field of nanophotonics, cellular dynamics, and biosensing due to their tunable electrical and optical properties. This work focuses on the multicolor patterning of two-dimensional nanoplatelets (NPLs) via two sequential self-assembly and direct electron-beam lithography steps. By using scanning electron microscopy, atomic force microscopy, and fluorescence microscopy, we demonstrate the successful fabrication of fluorescent nanoarrays with a thickness of only two or three monolayers (7-11 nm) and a feature line width of â¼40 nm, which is three to four NPLs wide. To this end, first, large-area thin films of red-emitting CdSe/ZnyCd1-yS and green-emitting CdSe1-xSx/ZnyCd1-yS core/shell NPLs are fabricated based on Langmuir-type self-assembly at the liquid/air interface. By varying the concentration of ligands in the subphase, we investigate the effect of interaction potential on the film's final characteristics to prepare thin superlattices suitable for the patterning step. Equipped with the ability to fabricate a uniform superlattice with a controlled thickness, we next perform nanopatterning on a thin film of NPLs utilizing a direct electron-beam lithography (EBL) technique. The effect of acceleration voltage, aperture size, and e-beam dosage on the nanopattern's resolution and fidelity is investigated for both of the presented NPLs. After successfully optimizing EBL parameters to fabricate single-color nanopatterns, we finally focus on fabricating multicolor patterns. The obtained micro/nanoarrays provide us with an innovative experimental platform to investigate biological interactions as well as Förster resonance energy transfer.
ABSTRACT
In this work, we present a new synthetic approach to colloidal PbS nanoplatelets (NPLs) utilizing a cation exchange (CE) strategy starting from CuS NPLs synthesized via the hot-injection method. Whereas the thickness of the resulting CuS NPLs was fixed at approx. 5 nm, the lateral size could be tuned by varying the reaction conditions, such as time from 6 to 16 h, the reaction temperature (120 °C, 140 °C), and the amount of copper precursor. In a second step, Cu+ cations were replaced with Pb2+ ions within the crystal lattice via CE. While the shape and the size of parental CuS platelets were preserved, the crystal structure was rearranged from hexagonal covellite to PbS galena, accompanied by the fragmentation of the monocrystalline phase into polycrystalline one. Afterwards a halide mediated ligand exchange (LE) was carried out in order to remove insulating oleic acid residues from the PbS NPL surface and to form stable dispersions in polar organic solvents enabling thin-film fabrication. Both CE and LE processes were monitored by several characterization techniques. Furthermore, we measured the electrical conductivity of the resulting PbS NPL-based films before and after LE and compared the processing in ambient to inert atmosphere. Finally, we fabricated field-effect transistors with an on/off ratio of up to 60 and linear charge carrier mobility for holes of 0.02 cm2 V-1 s-1.
ABSTRACT
Macroscopic superlattices of tin-doped indium oxide (ITO) nanocrystals (NCs) are prepared by self-assembly at the air/liquid interface followed by simultaneous ligand exchange with the organic semiconductor copper 4,4',4â³,4â´-tetraaminophthalocyanine (Cu4APc). By using X-ray photoelectron spectroscopy (XPS), grazing-incidence small-angle X-ray scattering (GISAXS), and ultraviolet-visible-near-infrared (UV-vis-NIR) spectroscopy, we demonstrate that the semiconductor molecules largely replace the native surfactant from the ITO NC surface and act as cross-linkers between neighboring particles. Transport measurements reveal an increase in electrical conductance by 9 orders of magnitude, suggesting that Cu4APc provides efficient electronic coupling for neighboring ITO NCs. This material provides the opportunity to study charge and spin transport through phthalocyanine monolayers.
