Growth Features of Bi2Te3Sb1.5 Films on Polyimide Substrates Obtained by Pulsed Laser Deposition.

Thermoelectric materials in the form of thin films are used to create a wide variety of sensors and devices. The efficiency of these devices depends on the quality and efficiency of the thermoelectric materials obtained in the form of thin films. Earlier, we demonstrated that it is possible to obtain high-performance Bi2Te3Sb1.5 films less than 1 µm thick on polyimide substrates by using the PLD method, and determined optimal growth conditions. In the current work, the relationship between growth conditions and droplet fraction on the surface, microstructure, grain size, film thickness and chemical composition was studied. A power factor of 5.25 µW/cm×K2 was achieved with the reduction of droplet fraction on the film surface to 0.57%. The dependencies of the film thickness were studied, and the effect of the thickness on the efficiency of the material is shown. The general trend in the growth dynamics for Bi2Te3Sb1.5 films we obtained is the reduction of crystalline size with Pressure-Temperature (PT) criterion. The results of our work also show the possibility of a significant reduction of droplet phase with simultaneous management of crystalline features and thermoelectric efficiency of Bi2Te3Sb1.5 films grown on polyimide substrates by varying growth conditions.

Femtosecond Er-Doped All-Fiber Laser with High-Density Well-Aligned Carbon-Nanotube-Based Thin-Film Saturable Absorber.

We have studied the ultrafast saturation behavior of a high-density well-aligned single-walled carbon nanotubes saturable absorber (HDWA-SWCNT SA), obtained by a high-pressure and high-temperature treatment of commercially available single-wall carbon nanotubes (SWCNTs) and related it to femtosecond erbium-doped fiber laser performance. We have observed the polarization dependence of a nonlinear optical saturation, along with a low saturation energy level of <1 fJ, limited to the detector threshold used, and the ultrafast response time of <250 fs, while the modulation depth was approximately 12%. We have obtained the generation of ultrashort stretched pulses with a low mode-locking launching threshold of ~100 mW and an average output power of 12.5 mW in an erbium-doped ring laser with the hybrid mode-locking of a VDVA-SWNT SA in combination with the effects of nonlinear polarization evolution. Dechirped pulses with a duration of 180 fs were generated, with a repetition rate of about 42.22 MHz. The average output power standard deviation was about 0.06% RMS during 3 h of measurement.

Non-Invasive Acoustic Monitoring of Gas Turbine Units by Fiber Optic Sensors.

In this article, we study the possibility of gas turbine unit (GTU) monitoring using interferometric fiber optic sensors. We used the Mach-Zehnder interferometer (MZI) scheme, which can be easily implemented and simply installed on the turbine, and also allows us to solve the problem of phase unwrapping conveniently. In this research, the following main steps were carried out: an experimental scheme based on the MZI was assembled, and its sensitive arm was fixed on the GTU under study; data on various operation modes of the GTU was collected; the data were subjected to frequency FFT analysis, based on which the main rotational speeds of the turbine were identified. With FFT analysis, we also demonstrated multiples harmonics, which appear in the case of GTU after operating time, caused by the number of blades. The possibility of GTU monitoring and analysis using a non-invasive compact fiber-optic sensor is demonstrated: spectral analysis is used to detect the rotor speed, as well as the presence or absence of high-order multiple frequencies indicating blade and bearing defects, which are determined by the number of GTU's blades and rolling bearing used as turbines rotor supports.

Study of Intra-Chamber Processes in Solid Rocket Motors by Fiber Optic Sensors.

In this study, an experimental study of the burning rate of solid fuel in a model solid propellant rocket motor (SRM) E-5-0 was conducted using a non-invasive control method with fiber-optic sensors (FOSs). Three sensors based on the Mach-Zehnder interferometer (MZI), fixed on the SRM E-5-0, recorded the vibration signal during the entire cycle of solid fuel burning. The results showed that, when using MZI sensors, the non-invasive control of solid fuel burnout is made possible both by recording the time of arrival of the combustion front to the sensor and by analyzing the peaks on the spectrogram of the recorded FOS signal. The main mode of acoustic vibrations of the chamber of the model SRM is longitudinal, and it changes with time, depending on the chamber length. Longitudinal modes of the combustion chamber were detected by MZI only after the combustion front passed its fixing point, and the microphone was unable to register them at all. The results showed that the combustion rate was practically constant after the first second, which was confirmed by the graph of the pressure versus time at the nozzle exit.

High-energy, sub-100 fs, all-fiber stretched-pulse mode-locked Er-doped ring laser with a highly-nonlinear resonator.

We report on ultra-short stretched pulse generation in an all-fiber erbium-doped ring laser with a highly-nonlinear germanosilicate fiber inside the resonator with a slightly positive net-cavity group velocity dispersion (GVD). Stable 84 fs pulses were obtained with a 12 MHz repetition rate at a central wavelength of 1560 nm with a 48.1 nm spectral pulse width (full width at half maximum, FWHM) and 30 mW average output power; this corresponds to the 29.7 kW maximum peak power and 2.5 nJ pulse energy obtained immediately from the oscillator.