Functional performance of a bi-layered chitosan-nano-hydroxyapatite osteochondral scaffold: a pre-clinical in vitro tribological study.

Osteochondral grafts are used for repair of focal osteochondral lesions. Autologous grafts are the gold standard treatment; however, limited graft availability and donor site morbidity restrict use. Therefore, there is a clinical need for different graft sources/materials which replicate natural cartilage function. Chitosan has been proposed for this application. The aim of this study was to assess the biomechanics and biotribology of a bioresorbable chitosan/chitosan-nano-hydroxyapatite osteochondral construct (OCC), implanted in an in vitro porcine knee experimental simulation model. The OCC implanted in different surgical positions (flush, proud and inverted) was compared to predicate grafts in current clinical use and a positive control consisting of a stainless steel graft implanted proud of the cartilage surface. After 3 h (10 800 cycles) wear simulation under a walking gait, subsidence occurred in all OCC samples irrespective of surgical positioning, but with no apparent loss of material and low meniscus wear. Half the predicate grafts exhibited delamination and scratching of the cartilage surfaces. No graft subsidence occurred in the positive controls but wear and deformation of the meniscus were apparent. Implanting a new chitosan-based OCC either optimally (flush), inverted or proud of the cartilage surface resulted in minimal wear, damage and deformation of the meniscus.

Developing Porous Ortho- and Pyrophosphate-Containing Glass Microspheres; Structural and Cytocompatibility Characterisation.

Phosphate-based glasses (PBGs) are promising materials for bone repair and regeneration as they can be formulated to be compositionally similar to the inorganic components of bone. Alterations to the PBG formulation can be used to tailor their degradation rates and subsequent release of biotherapeutic ions to induce cellular responses, such as osteogenesis. In this work, novel invert-PBGs in the series xP2O5·(56 - x)CaO·24MgO·20Na2O (mol%), where x is 40, 35, 32.5 and 30 were formulated to contain pyro (Q1) and orthophosphate (Q0) species. These PBGs were processed into highly porous microspheres (PMS) via flame spheroidisation, with ~68% to 75% porosity levels. Compositional and structural analysis using EDX and 31P-MAS NMR revealed that significant depolymerisation occurred with reducing phosphate content which increased further when PBGs were processed into PMS. A decrease from 50% to 0% in Q2 species and an increase from 6% to 35% in Q0 species was observed for the PMS when the phosphate content decreased from 40 to 30 mol%. Ion release studies also revealed up to a four-fold decrease in cations and an eight-fold decrease in phosphate anions released with decreasing phosphate content. In vitro bioactivity studies revealed that the orthophosphate-rich PMS had favourable bioactivity responses after 28 days of immersion in simulated body fluid (SBF). Indirect and direct cell culture studies confirmed that the PMS were cytocompatible and supported cell growth and proliferation over 7 days of culture. The P30 PMS with ~65% pyro and ~35% ortho phosphate content revealed the most favourable properties and is suggested to be highly suitable for bone repair and regeneration, especially for orthobiologic applications owing to their highly porous morphology.

Development and in vitro assessment of a bi-layered chitosan-nano-hydroxyapatite osteochondral scaffold.

An innovative approach was developed to engineer a multi-layered chitosan scaffold for osteochondral defect repair. A combination of freeze drying and porogen-leaching out methods produced a porous, bioresorbable scaffold with a distinct gradient of pore size (mean = 160-275 µm). Incorporation of 70 wt% nano-hydroxyapatite (nHA) provided additional strength to the bone-like layer. The scaffold showed instantaneous mechanical recovery under compressive loading and did not delaminate under tensile loading. The scaffold supported the attachment and proliferation of human mesenchymal stem cells (MSCs), with typical adherent cell morphology found on the bone layer compared to a rounded cell morphology on the chondrogenic layer. Osteogenic and chondrogenic differentiation of MSCs preferentially occurred in selected layers of the scaffold in vitro, driven by the distinct pore gradient and material composition. This scaffold is a suitable candidate for minimally invasive arthroscopic delivery in the clinic with potential to regenerate damaged cartilage and bone.

Metallic skeleton promoted two-phase durable icephobic layers.

HYPOTHESIS: The accretion of ice on component surfaces often causes severe impacts or accidents in modern industries. Applying icephobic surface is considered as an effective solution to minimise the hazards. However, the durability of the current icephobic surface and coatings for long-term service remains a great challenge. Therefore, it is indeed to develop new durable material structures with great icephobic performance. EXPERIMENTS: A new design concept of combining robust porous metallic skeletons and icephobic filling was proposed. Nickel/polydimethylsiloxane (PDMS) two-phase layer was prepared using porous Ni foam skeletons impregnated with PDMS as filling material by a two-step method. FINDINGS: Good icephobicity and mechanical durability have been verified. Under external force, micro-cracks could easily initiate at the ice/solid interface due to the small surface cavities and the difference of local elastic modulus between the ice and PDMS, which would promote the ice fracture and thus lead to low ice adhesion strength. The surface morphology and icephobicity almost remain unchanged after water-sand erosion, showing greatly improved mechanical durability. By combining the advantages of the mechanical durability of porous Ni skeleton and the icephobicity of PDMS matrix, the Ni foam/PDMS two-phase layer demonstrates great potentials for ice protection with long-term service time.

Evaluating the cytotoxicity of Ge-Sb-Se chalcogenide glass optical fibres on 3T3 mouse fibroblasts.

In vivo cancer detection based on the mid-infrared molecular fingerprint of tissue is promising for the fast diagnosis and treatment of suspected cancer patients. Few materials are mid-infrared transmissive, even fewer, which can be converted into functional, low-loss optical fibres for in vivo non-invasive testing. Chalcogenide-based glass optical fibres are, however, one of the few. These glasses are transmissive in the mid-infrared and are currently under development for use in molecular sensing devices. The cytotoxicity of these materials is however unknown. The cytotoxicity of Ge-Sb-Se chalcogenide optical glass fibres on 3T3 mouse fibroblast cells is here investigated. Fibres exposed to four different pre-treatment conditions are used: as-drawn (AD), propylamine-etched (PE), oxidised-and-washed (OW) and oxidised (Ox). To achieve the latter two conditions, fibres are treated with H2O2(aqueous (aq.)) and dried to produce a surface oxide layer; this is either washed off (OW) or left on the glass surface (Ox). Cellular response is investigated via 3 day elution and 14 day direct contact trials. The concentration of the metalloids (Ge, Sb and Se) in each leachate was measured via inductively coupled plasma mass spectrometry. Cell viability is assessed using the neutral red assay and scanning electron microscopy. The concentration of Ge, Sb and Se ions after a 3 day dissolution was as follows. In AD leachates, Ge: 0.40 mg L-1, Sb: 0.17 mg L-1, and Se: 0.06 mg L-1. In PE leachates, Ge: 0.22 mg L-1, Sb: 0.15 mg L-1, and Se: 0.02 mg L-1. In Ox leachates, Ge: 823.8 mg L-1, Sb: 2586.6 mg L-1, and Se: 3750 mg L-1. Direct contact trials show confluent cell layers on AD, PE and OW fibres after 14 days, while no cells are observed on the Ox surfaces. A >50% cell viability is observed in AD, PE and OW eluates after 3 days, when compared with Ox eluates (<10% cell viability). Toxicity in Ox is attributed to the notable pH change, from neutral pH 7.49 to acidic pH 2.44, that takes place on dissolution of the surface oxide layer in the growth media. We conclude, as-prepared Ge-Sb-Se glasses are cytocompatible and toxicity arises when an oxide layer is forced to develop on the glass surface.

Preclinical biological and physicochemical evaluation of two-photon engineered 3D biomimetic copolymer scaffolds for bone healing.

A major challenge in orthopedics is the repair of large non-union bone fractures. A promising therapy for this indication is the use of biodegradable bioinspired biomaterials that stabilize the fracture site, relieve pain and initiate bone formation and healing. This study uses a multidisciplinary evaluation strategy to assess immunogenicity, allergenicity, bone responses and physicochemical properties of a novel biomaterial scaffold. Two-photon stereolithography generated personalized custom-built scaffolds with a repeating 3D structure of Schwarz Primitive minimal surface unit cell with a specific pore size of ∼400 µm from three different methacrylated poly(d,l-lactide-co-ε-caprolactone) copolymers with lactide to caprolactone monomer ratios of 16 : 4, 18 : 2 and 9 : 1. Using in vitro and in vivo assays for bone responses, immunological reactions and degradation dynamics, we found that copolymer composition influenced the scaffold physicochemical and biological properties. The scaffolds with the fastest degradation rate correlated with adverse cellular effects and mechanical stiffness correlated with in vitro osteoblast mineralization. The physicochemical properties also correlated with in vivo bone healing and immune responses. Overall these observations provide compelling support for these scaffolds for bone repair and illustrate the effectiveness of a promising multidisciplinary strategy with great potential for the preclinical evaluation of biomaterials.

Impact of Serum Source on Human Mesenchymal Stem Cell Osteogenic Differentiation in Culture.

Human mesenchymal stem cells (MSCs) show promise for musculoskeletal repair applications. Animal-derived serum is extensively used for MSC culture as a source of nutrients, extracellular matrix proteins and growth factors. However, the routine use of fetal calf serum (FCS) is not innocuous due to its animal antigens and ill-defined composition, driving the development of alternatives protocols. The present study sought to reduce exposure to FCS via the transient use of human serum. Transient exposure to animal serum had previously proved successful for the osteogenic differentiation of MSCs but had not yet been tested with alternative serum sources. Here, human serum was used to support the proliferation of MSCs, which retained surface marker expression and presented higher alkaline phosphatase activity than those in FCS-based medium. Addition of osteogenic supplements supported strong mineralisation over a 3-week treatment. When limiting serum exposure to the first five days of treatment, MSCs achieved higher differentiation with human serum than with FCS. Finally, human serum analysis revealed significantly higher levels of osteogenic components such as alkaline phosphatase and 25-Hydroxyvitamin D, consistent with the enhanced osteogenic effect. These results indicate that human serum used at the start of the culture offers an efficient replacement for continuous FCS treatment and could enable short-term exposure to patient-derived serum in the future.

Integrated Multi-Assay Culture Model for Stem Cell Chondrogenic Differentiation.

Recent osteochondral repair strategies highlight the promise of mesenchymal progenitors, an accessible stem cell source with osteogenic and chondrogenic potential, used in conjunction with biomaterials for tissue engineering. For this, regenerative medicine approaches require robust models to ensure selected cell populations can generate the desired cell type in a reproducible and measurable manner. Techniques for in vitro chondrogenic differentiation are well-established but largely qualitative, relying on sample staining and imaging. To facilitate the in vitro screening of pro-chondrogenic treatments, a 3D micropellet culture combined with three quantitative GAG assays has been developed, with a fourth parallel assay measuring sample content to enable normalisation. The effect of transforming growth factor beta (TGF-ß) used to validate this culture format produced a measurable increase in proteoglycan production in the parallel assays, in both 2D and 3D culture configurations. When compared to traditional micropellets, the monolayer format appeared less able to detect changes in cell differentiation, however in-well 3D cultures displayed a significant differential response. Effects on collagen 2 expression confirmed these observations. Based on these results, a microplate format was optimised for 3D culture, in a high-throughput in-well configuration. This model showed improved sensitivity and confirmed the 3D micropellet in-well quantitative assays as an effective differentiation format compatible with streamlined, high-throughput chondrogenic screens.

In vitro cellular testing of strontium/calcium substituted phosphate glass discs and microspheres shows potential for bone regeneration.

Phosphate-based glasses (PBGs) are ideal materials for regenerative medicine strategies because their composition, degradation rates, and ion release profiles can easily be controlled. Strontium has previously been found to simultaneously affect bone resorption and deposition. Therefore, by combining the inherent properties of resorbable PBG and therapeutic activity of strontium, these glasses could be used as a delivery device of therapeutic factors for the treatment of orthopaedic diseases such as osteoporosis. This study shows the cytocompatibility and osteogenic potential of PBGs where CaO is gradually replaced by SrO in the near invert glass system 40P2 O5 ·(16-x)CaO·20Na2 O·24MgO·xSrO (x = 0, 4, 8, 12, and 16 mol%). Direct seeding of MG63 cells onto glass discs showed no significant difference in cell metabolic activity and DNA amount measurement across the different formulations studied. Cell attachment and spreading was confirmed via scanning electron microscopy (SEM) imaging at Days 3 and 14. Alkaline phosphatase (ALP) activity was similarly maintained across the glass compositions. Follow-on studies explored the effect of each glass composition in microsphere conformation (size: 63-125 µm) on human mesenchymal stem cells (hMSCs) in 3D cultures, and analysis of cell metabolic activity and ALP activity showed no significant differences at Day 14 over the compositional range investigated, in line with the observations from MG63 cell culture studies. Environmental SEM and live cell imaging at Day 14 of hMSCs seeded on the microspheres showed cell attachment and colonisation of the microsphere surfaces, confirming these formulations as promising candidates for regenerative medicine strategies addressing compromised musculoskeletal/orthopaedic diseases.

In vitro degradation and mechanical properties of PLA-PCL copolymer unit cell scaffolds generated by two-photon polymerization.

The manufacture of 3D scaffolds with specific controlled porous architecture, defined microstructure and an adjustable degradation profile was achieved using two-photon polymerization (TPP) with a size of 2 × 4 × 2 mm(3). Scaffolds made from poly(D,L-lactide-co-ɛ-caprolactone) copolymer with varying lactic acid (LA) and ɛ -caprolactone (CL) ratios (LC16:4, 18:2 and 9:1) were generated via ring-opening-polymerization and photoactivation. The reactivity was quantified using photo-DSC, yielding a double bond conversion ranging from 70% to 90%. The pore sizes for all LC scaffolds were see 300 µm and throat sizes varied from 152 to 177 µm. In vitro degradation was conducted at different temperatures; 37, 50 and 65 °C. Change in compressive properties immersed at 37 °C over time was also measured. Variations in thermal, degradation and mechanical properties of the LC scaffolds were related to the LA/CL ratio. Scaffold LC16:4 showed significantly lower glass transition temperature (T g) (4.8 °C) in comparison with the LC 18:2 and 9:1 (see 32 °C). Rates of mass loss for the LC16:4 scaffolds at all temperatures were significantly lower than that for LC18:2 and 9:1. The degradation activation energies for scaffold materials ranged from 82.7 to 94.9 kJ mol(-1). A prediction for degradation time was applied through a correlation between long-term degradation studies at 37 °C and short-term studies at elevated temperatures (50 and 65 °C) using the half-life of mass loss (Time (M1/2)) parameter. However, the initial compressive moduli for LC18:2 and 9:1 scaffolds were 7 to 14 times higher than LC16:4 (see 0.27) which was suggested to be due to its higher CL content (20%). All scaffolds showed a gradual loss in their compressive strength and modulus over time as a result of progressive mass loss over time. The manufacturing process utilized and the scaffolds produced have potential for use in tissue engineering and regenerative medicine applications.

Topographical and chemical effects of electrochemically assisted deposited hydroxyapatite coatings on osteoblast-like cells.

A recently commercialised hydroxyapatite electrochemically assisted chemical deposition technique (BoneMaster) has been shown to induce increased bone apposition; whether this response is caused by the surface topography or chemistry is unknown. An in-vitro examination using human osteoblast-like cells was performed on a series of BoneMaster-coated surfaces. The chemistry was separated from the topography using a thin gold coating; Thermanox coverslips were used as a control. BoneMaster surfaces showed significantly greater alkaline phosphatase activity and osteocalcin production compared with controls; however, no difference was found between the gold-coated and uncoated BoneMaster samples, indicating topography is the main contributing factor.

Development of an elastic cell culture substrate for a novel uniaxial tensile strain bioreactor.

Bioreactors can be used for mechanical conditioning and to investigate the mechanobiology of cells in vitro. In this study a polyurethane (PU), Chronoflex AL, was evaluated for use as a flexible cell culture substrate in a novel bioreactor capable of imparting cyclic uniaxial tensile strain to cells. PU membranes were plasma etched, across a range of operating parameters, in oxygen. Contact angle analysis and X-ray photoelectron spectroscopy showed increases in wettability and surface oxygen were related to both etching power and duration. Atomic force microscopy demonstrated that surface roughness decreased after etching at 20 W but was increased at higher powers. The etching parameters, 20 W 40 s, produced membranes with high surface oxygen content (21%), a contact angle of 66° ± 7° and reduced topographical features. Etching and protein conditioning membranes facilitated attachment, and growth to confluence within 3 days, of MG-63 osteoblasts. After 2 days with uniaxial strain (1%, 30 cycles/min, 1500 cycles/day), cellular alignment was observed perpendicular to the principal strain axis, and found to increase after 24 h. The results indicate that the membrane supports culture and strain transmission to adhered cells.

Effect of boron addition on the thermal, degradation, and cytocompatibility properties of phosphate-based glasses.

In this study eight different phosphate-based glass compositions were prepared by melt-quenching: four in the (P2O5)45-(CaO)16-(Na2O)15-x -(MgO)24-(B2O3) x system and four in the system (P2O5)50-(CaO)16-(Na2O)10-x -(MgO)24-(B2O3) x , where x = 0,1, 5 and 10 mol%. The effect of B2O3 addition on the thermal properties, density, molar volume, dissolution rates, and cytocompatibility were studied for both glass systems. Addition of B2O3 increased the glass transition (T(g)), crystallisation (T(c)), melting (T(m)), Liquidus (T(L)) and dilatometric softening (T(d)) temperature and molar volume (V(m)). The thermal expansion coefficient (α) and density (ρ) were seen to decrease. An assessment of the thermal stability of the glasses was made in terms of their processing window (crystallisation onset, T(c,ons) minus glass transition temperature, T(g)), and an increase in the processing window was observed with increasing B2O3 content. Degradation studies of the glasses revealed that the rates decreased with increasing B2O3 content and a decrease in degradation rates was also observed as the P2O5 content reduced from 50 to 45 mol%. MG63 osteoblast-like cells cultured in direct contact with the glass samples for 14 days revealed comparative data to the positive control for the cell metabolic activity, proliferation, ALP activity, and morphology for glasses containing up to 5 mol% of B2O3.

Composite PLA scaffolds reinforced with PDO fibers for tissue engineering.

Novel composite scaffolds were produced using long continuous bidirectional fibers embedded in an electrospun matrix, with the aim of using them in soft tissue engineering applications. The fibers are of polydioxanone and the matrix of polylactic acid. The novel manufacturing method consists of direct electrospinning performed on both sides of a collector that supports the already arranged fibers. The scaffolds were tested in vitro using 3T3 mouse fibroblasts as-obtained or functionalized with biotin or poly (dopamine). Functionalization did not significantly affect cells attachment, metabolic activity, or proliferation, but poly (dopamine) was proven to be effective in inducing hydrophilicity to the surface.

Investigating the use of coupling agents to improve the interfacial properties between a resorbable phosphate glass and polylactic acid matrix.

Eight different chemicals were investigated as potential candidate coupling agents for phosphate glass fibre reinforced polylactic acid composites. Evidence of reaction of the coupling agents with phosphate glass and their effect on surface wettability and glass degradation were studied along with their principle role of improving the interface between glass reinforcement and polymer matrix. It was found that, with an optimal amount of coupling agent on the surface of the glass/polymer, interfacial shear strength improved by a factor of 5. Evidence of covalent bonding between agent and glass was found for three of the coupling agents investigated, namely: 3-aminopropyltriethoxysilane; etidronic acid and hexamethylene diisocyanate. These three coupling agents also improved the interfacial shear strength and increased the hydrophobicity of the glass surface. It is expected that this would provide an improvement in the macroscopic properties of full-scale composites fabricated from the same materials which may also help to retain these properties for the desired length of time by retarding the breakdown of the fibre/matrix interface within these composites.

Influence of screw holes and gamma sterilization on properties of phosphate glass fiber-reinforced composite bone plates.

Polymers prepared from polylactic acid (PLA) have found a multitude of uses as medical devices. For a material that degrades, the main advantage is that an implant would not necessitate a second surgical event for removal. In this study, fibers produced from a quaternary phosphate-based glass (PBG) in the system 50P2O5-40CaO-5Na2O-5Fe2O3 were used to reinforce PLA polymer. The purpose of this study was to assess the effect of screw holes in a range of PBG-reinforced PLA composites with varying fiber layup and volume fraction. The flexural properties obtained showed that the strength and modulus values increased with increasing fiber volume fraction; from 96 MPa to 320 MPa for strength and between 4 GPa and 24 GPa for modulus. Furthermore, utilizing a larger number of thinner unidirectional (UD) fiber prepreg layers provided a significant increase in mechanical properties, which was attributed to enhanced wet out and thus better fiber dispersion during production. The effect of gamma sterilization via flexural tests showed no statistically significant difference between the sterilized and nonsterilized samples, with the exception of the modulus values for samples with screw holes. Degradation profiles revealed that samples with screw holes degraded faster than those without screw holes due to an increased surface area for the plates with screw holes in PBS up to 30 days. Scanning electron microscope (SEM) analysis revealed fiber pullout before and after degradation. Compared with various fiber impregnation samples, with 25% volume fraction, 8 thinner unidirectional prepreg stacked samples had the shortest fiber pull-out lengths in comparison to the other samples investigated.

Mechanical properties of epidermal cells of whole living roots of Arabidopsis thaliana: an atomic force microscopy study.

The knowledge of mechanical properties of root cell walls is vital to understand how these properties interact with relevant genetic and physiological processes to bring about growth. Expansion of cell walls is an essential component of growth, and the regulation of cell wall expansion is one of the ways in which the mechanics of growth is controlled, managed and directed. In this study, the inherent surface mechanical properties of living Arabidopsis thaliana whole-root epidermal cells were studied at the nanoscale using the technique of atomic force microscopy (AFM). A novel methodology was successfully developed to adapt AFM to live plant roots. Force-Indentation (F-I) experiments were conducted to investigate the mechanical properties along the length of the root. F-I curves for epidermal cells of roots were also generated by varying turgor pressure. The F-I curves displayed a variety of features due to the heterogeneity of the surface. Hysteresis is observed. Application of conventional models to living biological systems such as cell walls in nanometer regimes tends to increase error margins to a large extent. Hence information from the F-I curves were used in a preliminary semiquantitative analysis to infer material properties and calculate two parameters. The work done in the loading and unloading phases (hysteresis) of the force measurements were determined separately and were expressed in terms of "Index of Plasticity" (η), which characterized the elasticity properties of roots as a viscoelastic response. Scaling approaches were used to find the ratio of hardness to reduced modulus (H/E(*)).

Cytocompatibility and Mechanical Properties of Short Phosphate Glass Fibre Reinforced Polylactic Acid (PLA) Composites: Effect of Coupling Agent Mediated Interface.

In this study three chemical agents Amino-propyl-triethoxy-silane (APS), sorbitol ended PLA oligomer (SPLA) and Hexamethylene diisocyanate (HDI) were identified to be used as coupling agents to react with the phosphate glass fibre (PGF) reinforcement and the polylactic acid (PLA) polymer matrix of the composite. Composites were prepared with short chopped strand fibres (l = 20 mm, ϕ = 20 µm) in a random arrangement within PLA matrix. Improved, initial composite flexural strength (~20 MPa) was observed for APS treated fibres, which was suggested to be due to enhanced bonding between the fibres and polymer matrix. Both APS and HDI treated fibres were suggested to be covalently linked with the PLA matrix. The hydrophobicity induced by these coupling agents (HDI, APS) helped to resist hydrolysis of the interface and thus retained their mechanical properties for an extended period of time as compared to non-treated control. Approximately 70% of initial strength and 65% of initial modulus was retained by HDI treated fibre composites in contrast to the control, where only ~50% of strength and modulus was retained after 28 days of immersion in PBS at 37 °C. All coupling agent treated and control composites demonstrated good cytocompatibility which was comparable to the tissue culture polystyrene (TCP) control, supporting the use of these materials as coupling agent's within medical implant devices.

Cytocompatibility and effect of increasing MgO content in a range of quaternary invert phosphate-based glasses.

Recently, phosphate-based glass (PBG) fibers have been used to reinforce the biodegradable polymers polycaprolactone and polylactic acid, in order to fabricate materials suitable for use as resorbable bone fracture fixation devices. However, the PBG fibers investigated tended to degrade too quickly for application. Therefore, more durable PBG formulations were sought with emphasis remaining firmly placed on their biocompatibility. In this study, four invert PBG formulations (in the system P2O5-CaO-MgO-Na2O) were produced with fixed phosphate and calcium content at 40 and 25 mol%, respectively. MgO was added at 10-30 mol% in place of Na2O and the maximum divalent cation to phosphate ratio obtained was 1.375. Thermal analyses showed a linear increase in T(g) with increasing MgO content. This was proposed to be due to an increase in the cross-link density of the glass network, which also improved the chemical durability of the glass. EDX analyses were also conducted to verify the final composition of the glass. XRD analyses confirmed the amorphous nature of the glasses investigated. Rapid quenching of the Mg30 glass revealed a degree of surface crystallization, which was shown to be a CaMgP2O7 phase. The degradation rates of the glasses investigated decreased with increasing MgO content. The decrease in rate seen was almost two orders of magnitude (a x 50 difference was seen between glass Mg0 and Mg30). The cytocompatibility studies of the formulations investigated showed good cellular response over time for up to 14 days. Statistical analysis revealed that the formulations investigated gave a response comparable to the tissue culture plastic control. It is suggested that invert PBG provide degradation profiles and the cytocompatibility response desired to make these glasses useful for bone repair applications.

Analysis of calvarial bone defects in rats using microcomputed tomography: potential for a novel composite material and a new quantitative measurement.

Reconstruction of craniomaxillofacial defects is a challenge for surgeons and has psychological and functional burdens for patients. Undoubtedly, there is a need for improved biomaterials and techniques for craniomaxillofacial reconstruction. We assessed the potential regeneration of bone using three modifications of a novel composite and explored the validity of a new measurement using microcomputed tomography (micro-CT). We placed three different composite samples in calvarial defects in rats and analysed healing with micro-CT. The results showed that polycaprolactone (PCL) with phosphate glass fibre is promising for non-load bearing applications in the craniomaxillofacial region. Also, the new micro-CT measurement of the temporal characterisation of the mineralisation of bone (TCBM) has the potential to evolve into a reliable predictor of bony healing and its quality.