ABSTRACT
Dielectrophoretic separation of particles finds a variety of applications in the capture of species such as cells, viruses, proteins, DNA from biological systems, as well as other organic and inorganic contaminants from water. The ability to capture particles is constrained by poor volumetric scaling of separation force with respect to particle diameter, as well as the weak penetration of electric fields in the media. In order to improve the separation of sub-micron colloids, we present a scheme based on multiple interdigitated electrode arrays under mixed AC/DC bias. The use of high frequency longitudinal AC bias breaks the shielding effects through electroosmotic micromixing to enhance electric fields through the electrolyte, while a transverse DC bias between the electrode arrays enables penetration of the separation force to capture particles from the bulk of the microchannel. We determine the favorable biasing conditions for field enhancement with the help of analytical models, and experimentally demonstrate the improved capture from sub-micron colloidal suspensions with the mixed AC/DC electrostatic excitation scheme over conventional AC-DEP methods.
Subject(s)
Colloids/isolation & purification , Electrophoresis/instrumentation , Electrophoresis/methods , Colloids/chemistry , Equipment Design , Lab-On-A-Chip Devices , Microelectrodes , Microtechnology , Particle SizeABSTRACT
Hydrogen sulphide is found in raw fuels such as natural gas and coal/biomass-derived syngas. It is poisonous to catalysts and corrosive to metals and therefore needs to be removed. This is often achieved using metal oxides as reactive adsorbents, but metal oxides perform poorly when subjected to repeated cycles of sulphidation and re-oxidation as a result of complex structural and chemical changes. Here, we show that Zn-Ti-O-based adsorbents with nanofibrous morphology can sustain their initial reactivity and sulphur removal capacity over multiple regeneration cycles. These nanostructured sorbents offer rapid reaction rates that overcome the gas-transport limitations of conventional pellet-based sorbents and allow all of the material to be used efficiently. Regeneration can be carried out at the same temperature as the sulphidation step because of the higher reactivity, which prevents sorbent deterioration and reduces energy use. The efficient regeneration of the adsorbent is also aided by structural features such as the growth of hierarchical nanostructures and preferential stabilization of a wurtzite phase in the sulphidation product.
ABSTRACT
We report fabrication and use of a flexible array of nano-apertures for photolithography on curved surfaces. The batch-fabricated apertures are formed of metal-coated silicone tips. The apertures are formed at the end of the silicone tips by either electrochemical etching of the metal or plasma etching of a protective mask followed by wet chemical etching. The apertures are as small as 250 nm on substrates larger than several millimeters. We demonstrate how the nano-aperture array can be used for nano-fabrication on flat and curved substrates, and show the subsequent fabrication steps to form large arrays of sub-micron aluminum dots or vertical silicon wires.
ABSTRACT
Herein, we discuss the synthesis as well as material and photochemical characterization of nanometer-sized Ta(2)O(5) decorated, in a controlled fashion, on top of 20â nm diameter SiO(2) particles to yield a composite oxide with a tunable band-gap width. Particular emphasis is paid to control of particle size, and control of the distribution of the overlying oxide. The nanoscale dimension imparts a high surface area and introduces quantum confinement effects that displace the conduction band more negatively and the valence band more positively on the electrochemical scale of potentials. This band shift results in an increase of the number of possible participants in photocatalytic reactions. The band shift is shown to result in an increase in driving force for thermodynamically feasible reactions. By decorating SiO(2) with smaller-sized Ta(2)O(5), the interplay of the Lewis acidity of SiO(2) and the contact area between Ta(2)O(5) and SiO(2) is utilized to develop a photocatalyst with higher photoactivity than pure Ta(2)O(5).
ABSTRACT
The dynamic response of an oscillating microcantilever with a gold-coated tip interacting with dissimilar functionalized silica surfaces was studied in electrolyte solutions with pH ranging from 4 to 9. Silica surfaces were chemically modified, yielding dissimilar surfaces with -Br, -NH(2), and -CH(3) functional group terminations. The relative hydrophobicity of the surfaces was characterized by contact angle measurements. The surface charge of the functionalized surfaces was first probed with commonly used static AFM measurements and serves as a reference to the dynamic response data. The amplitude and phase of the cantilever oscillation were monitored and used to calculate the effective interaction stiffness and damping coefficient, which relate to the electrical double layer interactions and also to distance-dependent hydrodynamic damping at the solid/water interface. The data for the dynamic response of the AFM over silica surfaces as a function of chemical functionalization and electrolyte pH show that the effective stiffness has a distinctive dependence on the surface charge of functionalized silica surfaces. The hydrodynamic damping also correlates strongly with the relative hydrophobicity of the surface. The data reported here indicate that interfacial properties can be strongly affected by changing the chemical composition of surfaces.
ABSTRACT
Proton exchange membrane fuel cells have the potential for applications in energy conversion and energy storage, but their development has been impeded by problems with the membrane electrode assembly. Here, we demonstrate that a silicon-based inorganic-organic membrane offers a number of advantages over Nafion--the membrane widely used as a proton exchange membrane in hydrogen fuel cells--including higher proton conductivity, a lack of volumetric size change, and membrane electrode assembly construction capabilities. Key to achieving these advantages is fabricating a silicon membrane with pores with diameters of approximately 5-7 nm, adding a self-assembled molecular monolayer on the pore surface, and then capping the pores with a layer of porous silica. The silica layer reduces the diameter of the pores and ensures their hydration, resulting in a proton conductivity that is two to three orders of magnitude higher than that of Nafion at low humidity. A membrane electrode assembly constructed with this proton exchange membrane delivered an order of magnitude higher power density than that achieved previously with a dry hydrogen feed and an air-breathing cathode.
Subject(s)
Electric Power Supplies , Membranes, Artificial , Nanostructures/chemistry , Nanotechnology/methods , Humidity , Hydrogen/chemistry , Hydroxylation , Organosilicon Compounds , Particle Size , Porosity , Protons , Silanes/chemistry , Silicon/chemistry , Spectroscopy, Fourier Transform InfraredABSTRACT
This article demonstrates the feasibility of making a partially buried micro gas chromatography (micro-GC) column with a rounded channel wall profile, which enables coating the stationary phase more uniformly and shows better separation characteristics than a square deep reactive ion etched (DRIE) wall profile. A buried structure fabrication method was adapted to fabricate 34 cm long, 165 microm wide, and 65 microm deep partially buried microcolumns, which had a unique rounded microcolumn wall profile similar to that of a flattened circular tube. The separation characteristics were compared to that of a 34 cm long, 100 microm x 100 microm square DRIE microcolumn, which had a similar hydraulic diameter. Minimum height equivalent to a theoretical plate (HETP) and reduced HETP of 0.39 mm and 6.02, respectively, with a retention factor of 6.3 were obtained on the coated partially buried microcolumn compared to 0.66 mm and 6.73, respectively, on the coated square DRIE microcolumn with a similar retention factor. The partially buried microcolumn was found to perform closer to the theoretical approximation and this could be attributed to the uniform phase deposition in the partially buried microcolumn compared to the square DRIE microcolumn. A 10 component mix was separated on the partially buried microcolumn in 3.8 s with the maximum peak width at half-height equal to 0.2 s, while a similar mix separated at higher pressure and temperature conditions on the square DRIE microcolumn in 4.6 s. The rounded corners allowed depositing thinner stationary phase, which was reflected in the faster elution of n-C(12) on the partially buried microcolumn compared to the square DRIE microcolumn. The better performance of the partially buried microcolumn may be attributed to either the rounded channel wall profile, the clean channel structures produced by the fabrication process, or the double-etched wall profile, which lowers the Taylor-Aris dispersion.
Subject(s)
Chromatography, Gas/instrumentation , Microtechnology , Feasibility Studies , Time FactorsABSTRACT
Using sum-frequency vibrational spectroscopy, we found that water structure at nanoporous silica/water interfaces depended on the nanoporous film structure. For a periodic, self-assembled nanoporous film with monosized 2 nm pores occupying 20% of the top surface area, the surface vibrational spectrum was dominated by water in contact with silica, bare or covered by silane, at the top surface. It resembled the spectral characteristic of the hydrophilic water/silica or the hydrophobic water/silane interface. For a fractal nanoporous film with pores ranging from 5 to 50 nm in size occupying 90% of the top surface, the spectrum for a trimethyl silane-coated superhydrophobic porous film resembled largely that of a water/air interface. Only when the silane was completely removed would the spectrum revert to that characteristic of a hydrophilic water/silica interface. The surface charging behaviors of the bare nanoporous films in water with different pH were monitored by spectroscopic measurements and atomic force microscopy force measurements. The point of zero charge for the periodic porous film is around pH 2, similar to that of the flat silica surface. The point of zero charge could only be determined to be pH<6 for the fractal porous film because the thin fractal solid network limited the amount of surface charge and therefore, the accuracy of the measurements.
ABSTRACT
Microscale total analysis systems (microTAS) allow high-throughput analyses by integrating multiple processes, parallelization, and automation. Here we combine unit operations of microTAS to create a device that can perform multidimensional separations using a three-dimensional hybrid microfluidic/nanofluidic device composed of alternating layers of patterned poly(methyl methacrylate) and nanocapillary array membranes constructed from nuclear track-etched polycarbonate. Two consecutive electrophoretic separations are performed, the first being an achiral separation followed by a chiral separation of a selected analyte band. Separation conditions are optimized for a racemic mixture of fluorescein-isothiocyanate-labeled amino acids, serine and aspartic acid, chosen because there are endogenous D-forms of these amino acids in animals. The chiral separation is implemented using micellar electrokinetic chromatography using beta-cyclodextrin as the chiral selector and sodium taurocholate as the micelle-forming agent. Analyte separation is monitored by dual-beam laser-induced fluorescence detection. After separation in the first electrophoretic channel, the preselected analyte is sampled by the second-stage separation using an automated collection sequence with a zero-crossing algorithm. The controlled fluidic environment inherent to the three-dimensional architecture enables a series of separations in varying fluidic environments and allows sample stacking via different background electrolyte pH conditions. The ability to interface sequential separations, selected analyte capture, and other fluidic manipulations in the third dimension significantly improves the functionality of multilayer microfluidic devices.
Subject(s)
Amino Acids/chemistry , Amino Acids/isolation & purification , Microfluidic Analytical Techniques/methods , Nanotechnology/instrumentation , Fluorescein-5-isothiocyanate/chemistry , Injections , Polycarboxylate Cement/chemistry , Polymethyl Methacrylate/chemistry , StereoisomerismABSTRACT
The dynamic response of amplitude-modulated atomic force microscopy (AM-AFM) is studied at the solid/water interface with respect to changes in ionic concentration, applied surface potential, and surface protonation. Each affects the electric double layer in the solution, charge on the tip and the sample surface, and thus the forces affecting the dynamic response. A theoretical model is developed to relate the effective stiffness and hydrodynamic damping of the AFM cantilever that is due to the tip/surface interaction with the phase and amplitude signals measured in the AM-AFM experiments. The phase and amplitude of an oscillating cantilever are measured as a function of tip-sample distance in three experiments: mica surface in potassium nitrate solutions with different concentrations, biased gold surface in potassium nitrate solution, and carboxylic acid-terminated self-assembled monolayers (SAMs) on gold in potassium nitrate pH buffers. Results show that, over the range where the higher harmonic modes of the oscillation are negligible, the effective stiffness of the AFM cantilever increases to a maximum as the tip approaches the surface before declining again as a result of the repulsive electrical double layer interaction. For attractive electrical double-layer interactions, the effective stiffness declines monotonically as the tip approaches the surface. Similarly, the hydrodynamic damping of the tip increases and then decreases as the tip approaches the solid/water interface, with the magnitude depending on the species present in the solution.
ABSTRACT
Due to the numerous toxicological effects of lead, its presence in the environment needs to be effectively monitored. Incorporating a biosensing element within a microfluidic platform enables rapid and reliable determinations of lead at trace levels. A microchip-based lead sensor is described here that employs a lead-specific DNAzyme (also called catalytic DNA or deoxyribozyme) as a recognition element that cleaves its complementary substrate DNA strand only in the presence of cationic lead (Pb(2+)). Fluorescent tags on the DNAzyme translate the cleavage events to measurable, optical signals proportional to Pb(2+) concentration. The DNAzyme responds sensitively and selectively to Pb(2+), and immobilizing DNAzyme in the sensor permits both sensor regeneration and localization of the detection zone. Here, the DNAzyme has been immobilized on a PMMA surface using the highly specific biotin-streptavidin interaction. The strategy includes using streptavidin physisorbed on a PMMA surface to immobilize DNAzyme both on planar PMMA and on the walls of a PMMA microfluidic device. The immobilized DNAzyme retains its Pb(2+) detection activity in the microfluidic device and can be regenerated and reused. The DNAzyme shows no response to other common metal cations and the presence of these contaminants does not interfere with the lead-induced fluorescence signal. While prior work has shown lead-specific catalytic DNA can be used in its solubilized form and while attached to gold substrates to quantitate Pb(2+) in solution, this is the first use of the DNAzyme immobilized within a microfluidic platform for real time Pb(2+) detection.
Subject(s)
Biosensing Techniques/methods , DNA, Catalytic/chemistry , Enzymes, Immobilized/chemistry , Lead/analysis , Microfluidic Analytical Techniques/methods , Polymethyl Methacrylate/chemistry , Catalysis , Equipment Design , Equipment Failure Analysis , Fluorescence , Sensitivity and Specificity , Surface PropertiesABSTRACT
This article demonstrates how to prepare microfabricated columns (microcolumns) for organophosphonate and organosulfur compound separation that rival the performance of commercial capillary columns. Approximately 16,500 theoretical plates were generated with a 3 m long OV-5-coated microcolumn with a 0.25 microm phase thickness using helium as the carrier gas at 20 cm/s. Key to the advance was the development of deactivation procedures appropriate for silicon microcolumns with Pyrex tops. Active sites in a silicon-Pyrex microcolumn cause peak tailing and unwanted adsorption. Experimentally, we found that organosilicon hydride deactivation lowers adsorption activity in microcolumns more than silazane and silane treatments. But without further treatment, the phosphonate peaks continue to tail after the coating process. We found that heat treatment with pinacolyl methylphosphonic acid (PMP) eliminated the phosphonate peak tailing. In contrast, conventional resilylation employing N, O-bis(trimethylsilyl)acetamide, hexamethyldisilazane, and 1-(trimethylsilyl)imidazole does not eliminate peak tailing. Column activity tests show that the PMP treatment also improves the peaks for 2,6-dimethyl aniline, 1-octanol, and 1-decanol implying a decrease in the column's hydrogen bonding sites with the PMP treatment. FT-IR analysis shows that exposure to PMP forms a bond to the stationary phase that deactivates the active sites responsible for organophosphonate peak tailing.
Subject(s)
Chromatography, Gas/instrumentation , Organophosphonates/chemistry , Organophosphonates/isolation & purification , Organophosphorus Compounds/chemistry , Organophosphorus Compounds/isolation & purification , Sulfur Compounds/chemistry , Sulfur Compounds/isolation & purification , Soman/analogs & derivatives , Soman/chemistry , Spectroscopy, Fourier Transform Infrared , Time FactorsABSTRACT
One of the most pervasive problems afflicting people throughout the world is inadequate access to clean water and sanitation. Problems with water are expected to grow worse in the coming decades, with water scarcity occurring globally, even in regions currently considered water-rich. Addressing these problems calls out for a tremendous amount of research to be conducted to identify robust new methods of purifying water at lower cost and with less energy, while at the same time minimizing the use of chemicals and impact on the environment. Here we highlight some of the science and technology being developed to improve the disinfection and decontamination of water, as well as efforts to increase water supplies through the safe re-use of wastewater and efficient desalination of sea and brackish water.
Subject(s)
Technology/trends , Water Purification/methods , Water Supply , Agriculture/statistics & numerical data , Agriculture/trends , Conservation of Natural Resources/methods , Conservation of Natural Resources/trends , Disinfection/methods , Humans , Technology/economics , Water Purification/economicsABSTRACT
We propose a new type of micro/nano fluidic mixer based on non-equilibrium electrokinetics and demonstrate its mixing performance. We fabricate the device with two-step reactive ion etching, one for nanochannels and one for microchannels. Mixing is achieved by strong vortex structures formed near the micro/nano channel interface. We expect the proposed device to be beneficial in the development of micro total analysis systems, since it is simple in its design with minimal fabrication complications.
ABSTRACT
Hybrid microfluidic/nanofluidic devices offer unique capabilities for manipulating and analyzing minute volumes of expensive or hard-to-obtain samples. Here, multilayer poly-(methyl methacrylate) microchips, with multiple spatially isolated microfluidic channels interconnected by nanocapillary array membranes (NCAMs), are fabricated using an adhesive contact printing process. The NCAMs, positioned between the microfluidic channel layers, add functionality to the inter-microchannel fluid transfer unit operation. They do so because the transport of specific analytes through the NCAM can be controlled by adjusting the ionic strength, the polarity of the applied bias, the surface charge density, and the pore size. A simplified, floating injection technique for NCAM-coupled nanofluidic devices is described and compared with conventional biased injection. In the floating injection approach, a voltage is applied across the injection channel and the slight electric field extension at the cross-section is used to transfer analytes through the nanopores to the separation channel. Floating injection excels in plug reproducibility, separation resolution, and operation simplicity, although it decreases assay throughput relative to biased injection. Floating injection can avoid the uneven distribution of analytes in the microfluidic channel that sometimes results from biased injection because of the volume mismatch between NCAM nanopore transport capacity and the supply of fluid. Moreover, the pressure-driven flow caused by the mismatch of the EOFs in the microfluidic channels connected by an NCAM must be considered when using NCAMs with pore diameters below 50 nm.
Subject(s)
Microfluidic Analytical Techniques/methods , Electrophoresis, Capillary/instrumentation , Electrophoresis, Capillary/methods , Microfluidic Analytical Techniques/instrumentation , Nanotechnology/instrumentation , Polymethyl MethacrylateABSTRACT
Details are presented for the formulation, fabrication, and mechanical characterization of mesoscopic freestanding polydimethylsiloxane (PDMS) elastomer membranes, 10.0 microm thick and 5.0 mm in diameter, used to probe the rheology of a living epithelial sheet. In what is described as a composite diaphragm inflation (CDI) experiment, freestanding PDMS membranes are utilized as substrates for the culture of a sheet of epithelial cells. Together, the cell layer and the PDMS elastomer form a composite diaphragm (CD) that is suitable for mechanical testing in an axisymmetric membrane inflation experiment. In order to distinguish the rheological behavior of the epithelial sheet from the mechanical response of the elastomer using inflation test data, freestanding PDMS membranes should exhibit a highly compliant yet mechanically invariant finite load-deformation response when subjected to multiple inflation cycles following intermittent periods of cell culture. Given these considerations, we describe a method for preparing freestanding PDMS elastomer membrane specimens that are optically transparent, tensed, and wrinkle-free. Surface modifications intended to facilitate cell culture, namely water vapor plasma and ultraviolet light treatments, were shown to dramatically stiffen the mechanical response of the membranes, rendering them unusable as CD substrates. In this study, only PDMS membranes with physiosorbed collagen demonstrated the mechanical compliance, fatigue resistance, and environmental stability necessary for reliable use in CDI experiments.
Subject(s)
Dimethylpolysiloxanes/chemistry , Epithelial Cells , Microscopy/methods , Cell Adhesion , Cells, Cultured , Epithelial Cells/cytology , Rheology , Surface PropertiesABSTRACT
Details are given for the design, calibration, and operation of an apparatus for measuring the finite load-deformation behavior of a sheet of living epithelial cells cultured on a mesoscopic freestanding elastomer membrane, 10 microm thick and 5 mm in diameter. Although similar in concept to bulge tests used to investigate the mechanical properties of micromachined thin films, cell-elastomer composite diaphragm inflation tests pose a unique set of experimental challenges. Composite diaphragm (CD) specimens are extremely compliant (E<50 kPa), experience large displacements when subject to small inflation pressures (approximately 100 Pa), and must be continuously immersed in a bath of liquid culture medium during the acquisition of load-deformation measurements. Given these considerations, we have constructed an inflation apparatus consisting of an air-piston-cylinder pump integrated with a modular specimen mounting fixture that constitutes a horizontally semi-infinite reservoir of liquid culture medium. In a deformation-controlled inflation test, pressurized air is used to inflate a CD specimen into the liquid reservoir with minimum disturbance of the liquid-air interface. Piston displacements and absolute pump chamber air pressures are utilized as feedback to cycle the displaced (or inflated) CD volume V in a 0.05 Hz triangular or sinusoidal wave form (V(MIN)=0 microl, V(MAX)Subject(s)
Biomechanical Phenomena/instrumentation
, Elastomers/chemistry
, Epithelial Cells
, Keratinocytes
, Membranes, Artificial
, Cells, Cultured
, Elasticity
, Humans
ABSTRACT
An experimental technique is presented to measure reflectance at high sample temperature with respect to room temperature in the infrared using Fourier transform infrared fitted with a reflectometer. Sample temperature artifacts are accounted for by sequential measurements taken with the lamp source on and with the lamp source off. The sequential measurements are shown mathematically to correct for the modulation of sample and detector thermal emissions. Further, the technique is applied to a polyimide (PMDA-ODA) film on a layer of gold deposited on a thermally oxidized Si wafer. It is shown that the optical properties (index of refraction and extinction coefficient) remain relatively constant with temperature (from room temperature to 380 degrees C) in the 4000-6000 cm(-1) spectral region. The significant changes that occur with temperature are the change in thickness of the film and also the spectral properties in the 2000-4000 cm(-1) region. Also, by using a Lorentz oscillator model, it is shown that this method is able to discern that spectral features corresponding to the OH stretching bands at 3630 and 3470 cm(-1) show significant variation with increasing temperature.
Subject(s)
Algorithms , Imides/chemistry , Membranes, Artificial , Models, Chemical , Spectroscopy, Fourier Transform Infrared/methods , Computer Simulation , Infrared Rays , Spectroscopy, Fourier Transform Infrared/instrumentation , TemperatureABSTRACT
We report here a technique to print small volumes of liquid on a hydrophobic substrate. This process is based on the control of the critical parameters that govern a quasi-equilibrium liquid transfer process from one surface to another. We present a qualitative model that describes the physics of a transfer printing process between hydrophobic surfaces, and we use the parameters outlined in this model to manipulate the amount of liquid transferred between surfaces. We demonstrate the printing of discrete, small volumes (approximately 70 fL) of different liquid inks on a polymer substrate starting with volumes that are 8 orders of magnitude larger (a droplet of approximately 10 microL) in a simple two-step procedure.