Hazardous characteristics of dust waste from metal manufacturing industries in South Korea.

The Ministry of Environment, South Korea, is involved in efforts to reduce safety-related accidents that could occur during hazardous waste disposal and minimise the environmental impacts of waste disposal. To reach such goals, new factors have been added that contribute to the hazardous characteristics of hazardous waste. The Ministry is also expanding regulations on inorganic and organic components present in hazardous waste for these factors and continues to correct the classification system to establish standards for waste components. Metallic dust, for example, is mostly generated during the operation of melting furnaces or precipitators and dangerous materials contained in this dust may cause accidents, such as explosions or fires. South Korean accident cases have confirmed that waste containing hazardous materials, such as Mg, Al and Mg-Al alloys, can cause such events. Therefore, this study analysed 28 dust samples collected from the dust accumulated in precipitators in 28 metal manufacturing facilities in South Korea. Nine samples were flammable and four samples were reactive to water. Two samples also exhibited leaching toxicities. The results applied to relevant laws in South Korea showed that the proportion of waste containing hazardous characteristics increased from 7.14% in the previous management category to 39.29% in the extended category, an overall increase of 32.15 percentage points.

Measurement and analysis of biomass content using gas emissions from solid refuse fuel incineration.

In this study, we compared the results of biomass and biocarbon content analysis of Solid Refuse Fuels using 14C method and selective dissolution method. Solid Refuse fuel Samples for biomass and biocarbon contents analysis were each collected from the silos and stack of the respective three facilities. Samples collected for 1, 10, 20, and 30 days for each method were analyzed. The analysis data were grouped into sample period, type and method and the optimum method for the detection of the biomass and biocarbon content was estimated. The biomass and biocarbon content showed a partially normal distribution. However, it does not satisfy equal variance. Therefore, we applied the parametric statistics Welch's ANOVA test and the nonparametric statistics Kruskal-Wallis test to compare the means of each sample group. The results of the Kruskal-Wallis test showed that sapmles collected over 20 days at Facility A had the same mean value. Therefore, when analyzing biocarbon content using the 14C method, conducting analyses by collecting exhaust gases for more than 20 days reduces errors in the results.

Assessment of quality test methods for solid recovered fuel in South Korea.

Management of solid recovered fuel (SRF) in South Korea is unique from most other countries in that it is based on a single standard. All SRFs are distributed at the same price irrespective of their performance, resulting in utilization problems and a low degree of acceptance among consumers. Moreover, the difficulty of temperature maintenance during transportation, excessive ash content, and the use of inappropriate microwave acid digestion methods pose challenges to SRF reliability. To address these issues, we compared the relevant management statuses in South Korea with those of the international community and reviewed the effects of the transportation temperature, ash content, and microwave acid digestion technique. The moisture, ash, sulfur, and chlorine contents as well as the lower heating values (LHVs) of all the samples from South Korea were found to be below the standard [international] thresholds, and they were barely influenced by the transportation temperature. In addition, 5 g samples were found to be more appropriate for ash content analysis than the 20 g samples used in South Korea, with the former producing smaller standard deviations. The optimal microwave acid digestion conditions were also determined to be a reaction time with nitric acid of >10 min, temperature of 180 °C, and microwave power of 600 W. The results of this study highlight the need for revising the SRF test methods used in South Korea, to boost the market and enhance quality reliability.

Strategic environmental assessment for effective waste management in Korea: A review of the new policy framework.

This study examines the new policy framework, which includes effective environmental assessment procedure to manage waste in Korea. Concept of this framework pursues the important strategies toward the waste reduction, preservation of landfill area, stabilization and removal of hazardous substance in wastes, and optimal treatment for energy and material recovery from wastes. Therefore, it has begun on three points. First, activating the effective recycling system to reuse wastes will be essential to waste reduction. Second, the utilization of substitute resource can be expected through the optimal transforming the wastes into the recycled product, raw material, thermal energy, etc. Third, the characteristics of waste must be evaluated by strategic environmental assessment. To realize this concept, the strategic environment assessment with reinforcement of hazardous property, categorization of recycling type, and classification of environmental assessment procedure depending on the recycling type was provided. In addition, based on this environment assessment, the new policy framework was built through the established and revised Wastes Control Act by focusing on simple systematic procedure for decision of the possible recycling and strengthening the safety of the wastes to a higher level with promoting recycling activities.

Characteristics of PCDDs/PCDFs in stack gas from medical waste incinerators.

Toxic polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in 45 stack gas samples were measured from 19 medical waste incinerators in South Korea using high-resolution gas chromatography equipped with a high-resolution mass spectrometer. The average concentrations of the sum of 17 toxic PCDD/PCDF congeners emitted from the medical waste incinerators ranged from 0.153 to 101.9 ng/Sm3. Based on the World Health Organization toxic equivalency factor, they ranged from 0.007 to 5.437 ng-TEQ/Sm3. The congener patterns of PCDDs/PCDFs were described using principal component analysis and presented four patterns. In the evaluation of annual average total TEQ concentrations, outlying stack gas samples were excluded. In this study, the number of chlorine substitutions was evaluated as an important factor in congener patterns. Coefficient of determination values were employed for evaluation of correlation between PCDDs and PCDFs. 1,2,3,4,6,7,8-HpCDF was measured as the most emitted congener, while 2,3,4,7,8-PeCDF was the greatest TEQ contributor.

Determination and characterization of pharmaceuticals in sludge from municipal and livestock wastewater treatment plants.

This study investigated 24 pharmaceuticals compounds belonging to the classes of analgesics, stimulants, anti-seizures, non-steroidal anti-inflammatory drugs (NSAIDs), and antibiotics in the sludge of 12 municipal sewage treatment plants (S-sludge) and 4 livestock wastewater treatment plants (L-sludge) located across Korea. Over 70% of the target compounds were detected in at least one sample of S-sludge and L-sludge. The total concentration of the target pharmaceutical compounds detected in S-sludge was 2.622-422.8 mg kg-1and the most dominant compound was acetylsalicylic acid (ASA: 0.374-367.0 mg kg-1) whereas in L-sludge, the total concentration was 43.87-156.8 mg kg-1and the most abundant compound was oxytetracycline (OTC: 34.54-86.39 mg kg-1). Cluster analysis revealed two distinct groups: group A, which were S-sludge samples including ASA, carbamazepine (CBM), and others, and group B were L-sludge samples, dominated by antibiotics (CTC, OTC, LIN). The total daily load amount of the target pharmaceuticals in S-sludge was 0.010-268.9 kg day-1 while the L-sludge was 0.021-0.529 kg day-1. The estimated amounts of the target pharmaceutical discharged from S-sludge and L-sludge into the Korean environment were 150.2 ± 47.94 ton yr-1 and 15.05 ± 5.671 ton yr-1 respectively, but the discharged amount of antibiotics from S-sludge (6.945 ton yr-1) was lower than that from L-sludge (9.234 ton yr-1).

Characterization of wastes from construction and demolition sector.

In Republic of Korea, construction and demolition (C&D) waste accounts for 49.9% of the total waste. In the present work, the mineralogical composition, the concentrations of 11 heavy metals, 19 PAH, and 7 polychlorinated biphenyl (PCB) congeners present in the 6 broad category (9 subcategories) of C&D hazardous waste were discussed along with their leaching characteristics. In concrete/mixed cement waste, the concentrations of As, Cr(6+), Hg, and Zn were in the range of 1.76-7.86, ND-1.63, 0.026-0.047, and 110.90-280.17 mg/kg, respectively. The asphalt waste sample A1 possessed relatively high concentrations of phenanthrene, fluoranthene, pyrene, benz(a)anthracene, benzo(a)pyrene, and indeno(1,2,3-cd)pyrene comparing to the other samples and it contains 0.08-0.1% of coal tar. Hazardous nature of the C&D wastes greatly depends on the source of the collection. Zn concentration was above 1000 mg/kg for road asphalt waste samples A4 and A5. Total PCB concentration were high in the soil waste sample S1 (130 µg/kg) as it was the excavated soil obtained from the premises of an oil station. Leaching of As, Ba, CN(-), and F(-) were observed in most of the C&D waste samples.

Static and dynamic flow analysis of PBDEs in plastics from used and end-of-life TVs and computer monitors by life cycle in Korea.

This study focused on a quantitative substance flow analysis (SFA) of polybrominated diphenyl ethers (PBDEs) in plastics from obsolete TVs and computer monitors that often contain large amounts of the flame retardants. According to the results of the static SFA study, 1.87 tons and 0.28 tons of PBDEs from newly manufactured TVs and computer monitors were introduced into households in 2011 in Korea, respectively. There were approximately 924 tons and 90.3 tons of PBDEs present in TVs and computer monitors in households during product use, respectively. The results of the dynamic SFA study indicated that in 2017 the amount of PBDEs from TVs and computer monitors in the recycling stage is expected to be 2.63 tons and 0.1 tons, respectively. Large fractions of PBDEs from used TVs are present in recycled plastics, while PBDE-containing computer monitors are exported to Southeast Asian countries. This research indicates that PBDEs were emitted the most from recycled plastic pellet processes upon recycling. Further study may be warranted to focus the flow of PBDEs in recycled plastic products in order to determine the final destination and disposal of these chemicals in the environment.

1H-NMR-based profiling of organic components in leachate from animal carcasses disposal site with time.

Leachate, generated by the decomposition of animal carcasses, presents many environmental, sanitary, and food safety hazards. However, research on the characteristics of leachate is lacking. In this study, we performed biochemical profiling of leachate from two animal species (pig and cattle) in two soil types (sandy loam and sandy soil) using (1)H-NMR-based profiling, followed by multivariate data analysis. The leachate was collected from a well-controlled artificial burial site over a 31-week period. Principal components analysis (PCA) of the NMR data showed similar patterns between species and soil types. Organic components, including organic acids and phenols, predominated, and their levels increased with time. The methylamine level in leachate from pig carcasses 18 weeks following burial was significantly higher than that from cattle carcasses; leachate from cattle carcasses in sandy soil 1 week after burial contained unique components (specifically ethanol, formate, alanine, N-methylation, and taurine), in contrast with those from sandy loam soil. This study suggests that a NMR-based profiling approach is useful to characterize the organic components in leachate from animal carcasses over time.

Emission of polybrominated diphenyl ethers (PBDEs) in use of electric/electronic equipment and recycling of e-waste in Korea.

The emission rates of polybrominated diphenyl ethers (PBDEs) from electric/electronic products during their use and disposal were estimated. E-wastes, including televisions and refrigerators, gathered at recycling centers were also analyzed to estimate their emissions. The average concentrations of PBDEs in TV rear covers produced before and after the year 2000 were 145,027 mg/kg and 14,049 mg/kg, respectively. The PBDEs concentration in TV front covers was lower than the concentration in TV rear covers. The concentration in the components of the refrigerator samples ranged from ND to 445 mg/kg. We estimated the atmospheric emissions of PBDEs based on the concentrations. The annual emissions from TV rear covers produced before 2000 were calculated to be approximately 162.1 kg and after 2000, the annual emissions were 18.7 kg. Refrigerators showed the lowest annual emissions of PBDEs (0.7 kg). The atmospheric concentrations were also measured to calculate emissions generated during the recycling process. The highest concentration was 16.86 ng/m(3) emitted from the TV sets during the dismantling process. The concentrations of PBDEs generated in the plastic processing field ranged from 2.05 to 5.43 ng/m(3) depending on the products, and ambient air in open-air yards showed concentrations in the range of 0.32 to 5.55 ng/m(3). Emission factors for the recycling process were calculated using the observed concentrations. The estimated emissions according to the emission factors ranged from 0.3×10(-1) to 90.3 kg/year for open-air yards and from 0.1×10(-1) to 292.7 kg/year for the dismantling and crushing processes of TV set, depending on the production year.

Ecological risk assessment of chemicals migrated from a recycled plastic product.

OBJECTIVES: Potential environmental risks caused by chemicals that could be released from a recycled plastic product were assessed using a screening risk assessment procedure for chemicals in recycled products. METHODS: Plastic slope protection blocks manufactured from recycled plastics were chosen as model recycled products. Ecological risks caused by four model chemicals -di-(2-ethylhexyl) phthalate (DEHP), diisononyl phthalate (DINP), cadmium (Cd), and lead (Pb)- were assessed. Two exposure models were built for soil below the block and a hypothetic stream receiving runoff water. Based on the predicted no-effect concentrations for the selected chemicals and exposure scenarios, the allowable leaching rates from and the allowable contents in the recycled plastic blocks were also derived. RESULTS: Environmental risks posed by slope protection blocks were much higher in the soil compartment than in the hypothetic stream. The allowable concentrations in leachate were 1.0×10(-4), 1.2×10(-5), 9.5×10(-3), and 5.3×10(-3) mg/L for DEHP, DINP, Cd, and Pb, respectively. The allowable contents in the recycled products were 5.2×10(-3), 6.0×10(-4), 5.0×10(-1), and 2.7×10(-1) mg/kg for DEHP, DINP, Cd, and Pb, respectively. CONCLUSIONS: A systematic ecological risk assessment approach for slope protection blocks would be useful for regulatory decisions for setting the allowable emission rates of chemical contaminants, although the method needs refinement.

Hazardous waste characterization among various thermal processes in South Korea: a comparative analysis.

Ministry of Environment, Republic of Korea (South Korea) is in progress of converting its current hazardous waste classification system to harmonize it with the international standard and to set-up the regulatory standards for toxic substances present in the hazardous waste. In the present work, the concentrations along with the trend of 13 heavy metals, F(-), CN(-) and 19 PAH present in the hazardous waste generated among various thermal processes (11 processes) in South Korea were analyzed along with their leaching characteristics. In all thermal processes, the median concentrations of Cu (3.58-209,000 mg/kg), Ni (BDL-1560 mg/kg), Pb (7.22-5132.25mg/kg) and Zn (83.02-31419 mg/kg) were comparatively higher than the other heavy metals. Iron & Steel thermal process showed the highest median value of the heavy metals Cd (14.76 mg/kg), Cr (166.15 mg/kg) and Hg (2.38 mg/kg). Low molecular weight PAH (BDL-37.59 mg/kg) was predominant in sludge & filter cake samples present in most of the thermal processes. Comparatively flue gas dust present in most of the thermal processing units resulted in the higher leaching of the heavy metals.

Nationwide monitoring of atmospheric PCDD/Fs and dioxin-like PCBs in South Korea.

Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (DL-PCBs) were measured in ambient air samples collected from different parts of South Korea in 2008, and the measured levels were used for assessing the spatial and temporal distribution of atmospheric PCDDFs and DL-PCBs in South Korea. The average concentrations of atmospheric PCDD/Fs and DL-PCBs among the 37 sites were 28 fg I-TEQ m(-3) (ND~617) and 1 fg WHO-TEQ m(-3) (ND~0.016). Elevated atmospheric levels of PCDD/Fs and DL-PCBs observed at residential/industrial sites and in the north-west of Korea, indicated a potential contribution and impacts of anthropogenic sources of PCDD/Fs and DL-PCBs. These levels were similar or lower than those previously reported in other ambient air surveys. Average concentrations of PCDD/Fs showed small seasonal variations (ANOVA analysis, p=0.144). The highest concentrations of PCDD/Fs were observed during winter, followed by spring, autumn and summer. Atmospheric PCDD/Fs and DL-PCBs in South Korea rapidly decreased during the last 10 years (1998-2008), demonstrating the efficiency of stricter regulations and the application of best available technologies/best environmental practices at emission sources. Comparison of the congener profiles and principal component analysis showed that current atmospheric PCDD/Fs are mostly influenced by industrial sources and PCBs from old commercial PCB uses. Nationwide POPs monitoring will continue and allows an effective evaluation of the implementation of the Stockholm Convention on POPs.

Assessment of fates of estrogens in wastewater and sludge from various types of wastewater treatment plants.

We measured five estrogens in the wastewater samples from the municipal wastewater treatment plants (M-WWTPs), livestock wastewater treatment plants (L-WWTPs), hospital WWTPs (H-WWTPs) and pharmaceutical manufacture WWTPs (P-WWTPs) in Korea. The L-WWTPs showed the highest total concentration (0.195-10.4 µg L(-1)) of estrogens in the influents, followed by the M-WWTPs (0.028-1.15 µg L(-1)), H-WWTPs (0.068-0.130 µg L(-1)) and P-WWTPs (0.015-0.070 µg L(-1)). Like the influents, the L-WWTPs (0.003-0.729 µg L(-1)) and the M-WWTPs (0.001-0.299µgL(-1)) also showed higher total concentration of estrogens in the effluents than the H-WWTPs (0.002-0.021 µg L(-1)) and P-WWTPs (0.011 µg L(-1) in one sample). The L-WWTPs (37.5-543 µg kg(-1), dry weight) showed higher total concentrations in sludge than the M-WWTPs (3.16-444 µg kg(-1), dry weight) like the wastewater. The distribution of estrogens in the WWTPs may be affected by their metabolism in the human body, their transition through biological treatment processes, and their usage for livestock growth. Unlike the concentration results, the daily loads of estrogens from the M-WWTPs were the highest, which is related to the high capacities of WWTPs.

Occurrence and distribution of pharmaceuticals in wastewater from households, livestock farms, hospitals and pharmaceutical manufactures.

Twenty-four pharmaceuticals were measured in wastewater from 12 municipal wastewater treatment plants (M-WWTPs), four livestock WWTPs (L-WWTPs), four hospital WWTPs (H-WWTPs) and four pharmaceutical manufacture WWTPs (P-WWTPs). The total concentration of pharmaceuticals in the influent samples was highest in the L-WWTPs followed by the P-WWTPs, H-WWTPs and M-WWTPs. The effluents had different patterns of pharmaceuticals than their corresponding influents because of the different fate of each compound in the WWTPs. Non-steroidal anti-inflammatory drugs (NSAIDs) were the most dominant in the influents from the M-WWTPs and P-WWTPs, while antibiotics were dominantly detected in the L-WWTP. In the H-WWTP influents, NSAIDs, caffeine and carbamazepine were dominant. In the P-WWTPs, the distribution of pharmaceuticals in the effluents varied with sampling sites and periods. The M-WWTP influents had the highest daily loads, while the effluents showed somewhat similar levels in all source types.

Characteristics and emission factors of PCDD/Fs in various industrial wastes in South Korea.

Since South Korea ratified Stockholm Convention in January 2007, there is an obligation to survey the national emission of PCDD/Fs through environmental routes other than the air for taking actions to reduce and/or eliminate the release of PCDD/Fs. In this study, PCDD/F-containing wastes from various industrial emission sources in Korea (n=388) except from incinerators were investigated to elucidate the emission characteristics and their emission factors of PCDD/Fs in each industry. The concentrations of PCDD/Fs in waste samples ranged ND-96,200 ng I-TEQ kg(-1) (or 66,600 ng WHO-TEQ kg(-1)) for solid phase samples and ND-11,100 pg I-TEQL(-1) (or 6800 ng WHO-TEQ L) for liquid samples, respectively. Elevated levels of PCDD/F concentrations and emission factors were found in the wastes from productions of Cu, Al, Zn, Iron/steel, Pb, EDC/VCM/PVC and from waste landfill sites. The wastes from productions of cement (kilns) and acetylene (carbide method) showed elevated levels of PCDD/F emission factors only. The dominant congeners were OCDD, OCDF, 1,2,3,4,6,7,8-HpCDF and 1,2,3,4,5,7,8-HpCDD. The PCDF ratios in samples from thermal processes and solid phase samples were 69% and 70%, respectively. The ratio of OCDD congener (about 23.5%) was higher than that of other congeners in both solid and liquid phase wastes. These results can be used as a useful reference for the establishment of the PCDD/F inventory and their management plans.

Seasonal and particle size-dependent variations in gas/particle partitioning of PCDD/Fs.

This study monitored particle size-dependent variations in atmospheric polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). Two gas/particle partitioning models, the subcooled liquid vapor pressure (P(L)(0)) and the octanol-air partition coefficient (K(OA)) model, were applied to each particle sizes. The regression coefficients of each fraction against the gas/particle partition coefficient (K(P)) were similar for separated particles within the same sample set but differed for particles collected during different periods. Gas/particle partitioning calculated from the integral of fractions was similar to that of size-segregated particles and previously measured bulk values. Despite the different behaviors and production mechanisms of atmospheric particles of different sizes, PCDD/F partitioning of each size range was controlled by meteorological conditions such as atmospheric temperature, O(3) and UV, which reflects no source related with certain particle size ranges but mixed urban sources within this city. Our observations emphasize that when assessing environmental and health effects, the movement of PCDD/Fs in air should be considered in conjunction with particle size in addition to the bulk aerosol.

National monitoring of PCDD/DFs in environmental media around incinerators in Korea.

To examine the levels of PCDD/DFs pollution in environmental samples in the vicinity of various incinerators, the levels of PCDD/DFs in air and soil samples collected near 17 incinerators and stack emission gases were investigated between 2003 and 2006. A total of 434 soil, 28 stack emission gas, and 38 air samples were analyzed for their PCDD/DFs concentrations. The PCDD/DFs concentrations in the flue gas samples ranged from 0.02 to 16.41 ng I-TEQ/Sm(3), with an arithmetical mean value of 3.13 ng I-TEQ/Sm(3). The PCDD/DFs concentrations in the air samples ranged from 0.032 to 0.965 pg I-TEQ/Sm(3). The soil samples contained between N.D. and 153.23 pg I-TEQ/g-dry, with an average of 7.36 pg I-TEQ/g-dry. These levels were generally consistent with or lower than many previous studies. The average PCDD/DFs levels in the soil samples decrease with increasing distance from the incinerator. From the PCDD/DFs level gradient from each plant, a distance of 500 m is suggested as being under the influence of an incinerator.

Assessment of PCDD/F risk after implementation of emission reduction at a MSWI.

Municipal solid waste incinerators (MSWIs) have been shown to be important sources of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). The emission of PCDD/Fs by MSWIs is a controversial subject in human health risk assessment. In this study the effect of a MSWI on a residential area was assessed before and after the installation of an additional treatment system for flue gas. This additional treatment system resulted in a dramatic decrease in PCDD/F concentrations in stack flue gas samples by 99.98%, while the concentrations in air decreased by approximately 50% (36,500 and 0.75 pg I-TEQ m(-3) for air in 1999; 3.5 and 0.38 pg I-TEQ m(-3) in 2002; 1.6 and 0.076 pg I-TEQ m(-3) in 2005 for stack gas and air, respectively). Considering the congener distributions of PCDD/Fs between stack flue gas and air samples, the study area seemed to have been contaminated by other urban sources as well as the MSWI. ISC3 model results support the conclusion that this incinerator became only a minor contributor to the study area after installation of the supplementary systems. This resulted from both proper MSWI operation using modern technology and additional sources of contaminants in this region. Finally, PCDD/F uptake by humans through inhalation of contaminated air was estimated. Assuming that inhalation exposure contributes 10% of total exposure, total exposure was lower than WHO guidelines. These results confirm that proper operation and maintenance of the incinerator led to a reduction in emissions and potential health impacts of PCDD/Fs.

Levels of polychlorinated biphenyls (PCBs) in transformer oils from Korea.

Using Korean waste official method, polychlorinated biphenyls (PCBs) were analyzed from 33 transformer oils collected under National Institute of Environmental Research (NIER) in Republic of Korea (ROK) and their emission rate in Korea was estimated. Practical quantification limits analyzed by this method were in the ranges of 0.02 and 0.05 mg L(-1), and recovery of samples was in the ranges of 77-97%. The analytical results showed that PCBs in the transformer oils were identified as Aroclor 1242, 1254 or 1260. Twenty-nine samples were determined to contain PCBs of >0.05 mg L(-1) and among these samples, nine samples contained to have >2 mg kg(-1) which is limit of Waste Control Act (WCA) with regard to PCBs in transformer oil from Korea. The concentrations of PCBs in transformer oils were between N.D. (not detected) and 48.33 mg kg(-1). PCBs concentrations did not exceed 50 mg kg(-1) which is generally accepted limit for the definition of waste in POPs Guideline of Basel Convention.