Enhancement of ZnO@RuO2 bifunctional photo-electro catalytic activity toward water splitting.

Catalytic materials are the greatest challenge for the commercial application of water electrolysis (WEs) and fuel cells (FCs) as clean energy technologies. There is a need to find an alternative to expensive and unavailable platinum group metal (PGM) catalysts. This study aimed to reduce the cost of PGM materials by replacing Ru with RuO2 and lowering the amount of RuO2 by adding abundant and multifunctional ZnO. A ZnO@RuO2 composite in a 10:1 molar ratio was synthesized by microwave processing of a precipitate as a green, low-cost, and fast method, and then annealed at 300°C and 600°C to improve the catalytic properties. The physicochemical properties of the ZnO@RuO2 composites were investigated by X-ray powder diffraction (XRD), Raman and Fourier transform infrared (FTIR) spectroscopy, field emission scanning electron microscopy (FESEM), UV-Vis diffuse reflectance spectroscopy (DRS), and photoluminescence (PL) spectroscopy. The electrochemical activity of the samples was investigated by linear sweep voltammetry in acidic and alkaline electrolytes. We observed good bifunctional catalytic activity of the ZnO@RuO2 composites toward HER and OER in both electrolytes. The improved bifunctional catalytic activity of the ZnO@RuO2 composite by annealing was discussed and attributed to the reduced number of bulk oxygen vacancies and the increased number of established heterojunctions.

Removal of copper and iron from ethanolic solutions by an anion exchange resin and its implication to rare-earth magnet recycling.

In the recycling of end-of-life rare-earth magnets, the recovery of non-rare earth constituents is often neglected. In the present study, strong cation and anion exchange resins were tested batchwise for the recovery of the non-rare-earth constituents of permanent magnets (copper, cobalt, manganese, nickel and iron) from synthetic aqueous and ethanolic solutions. The cation exchange resin recovered most of metal ions from aqueous and ethanolic feeds, whereas the anion exchange resin could selectively recover copper and iron from ethanolic feeds. The highest uptake of iron and copper was found for 80 vol% and 95 vol% multi-element ethanolic feeds, respectively. A similar trend in selectivity of the anion resin was observed in breakthrough curve studies. Batch experiments, UV-Vis, FT-IR and XPS studies were performed to elucidate the ion exchange mechanism. The studies indicate that the formation of chloro complexes of copper and their exchange by the (hydrogen) sulfate counter ions of the resin have an important role in the selective uptake of copper from the 95 vol% ethanolic feed. Iron(II) was largely oxidized to iron(III) in ethanolic solutions and was expected to be recovered by the resin in the form of iron(II) and iron(III) complexes. The moisture content of the resin did not have a significant role on the selectivity for copper and iron.

Crystal Structure and Electrical Properties of Ruthenium-Substituted Calcium Copper Titanate.

This paper reports a detailed study of crystal structure and dielectric properties of ruthenium-substituted calcium-copper titanates (CaCu3Ti4-xRuxO12, CCTRO). A series of three samples with different stoichiometry was prepared: CaCu3Ti4-xRuxO12, x = 0, 1 and 4, abbreviated as CCTO, CCT3RO and CCRO, respectively. A detailed structural analysis of CCTRO samples was done by the Rietveld refinement of XRPD data. The results show that, regardless of whether Ti4+ or Ru4+ ions are placed in B crystallographic position in AA'3B4O12 (CaCu3Ti4-xRuxO12) unit cell, the crystal structure remains cubic with Im3¯ symmetry. Slight increases in the unit cell parameters, cell volume and interatomic distances indicate that Ru4+ ions with larger ionic radii (0.62 Å) than Ti4+ (0.605 Å) are incorporated in the CaCu3Ti4-xRuxO12 crystal lattice. The structural investigations were confirmed using TEM, HRTEM and ADF/STEM analyses, including EDXS elemental mapping. The effect of Ru atoms share in CaCu3Ti4-xRuxO12 samples on their electrical properties was determined by impedance and dielectric measurements. Results of dielectric measurements indicate that one atom of ruthenium per CaCu3Ti4-xRuxO12 unit cell transforms dielectric CCTO into conductive CCT3RO while preserving cubic crystal structure. Our findings about CCTO and CCT3RO ceramics promote them as ideal tandem to overcome the problem of stress on dielectric-electrode interfaces in capacitors.

Bifunctional catalytic activity of Zn1-xFexO toward the OER/ORR: seeking an optimal stoichiometry.

Eco-friendly and rapid microwave processing of a precipitate was used to produce Fe-doped zinc oxide (Zn1-xFexO, x = 0, 0.05, 0.1, 0.15 and 0.20; ZnO:Fe) nanoparticles, which were tested as catalysts toward the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) in a moderately alkaline solution. The phase composition, crystal structure, morphology, textural properties, surface chemistry, optical properties and band structure were examined to comprehend the influence of Zn2+ partial substitution with Fe3+ on the catalytic activity of ZnO:Fe. Linear sweep voltammetry showed an improved catalytic activity of ZnO:5Fe toward the ORR, compared to pure ZnO, while with increased amounts of the Fe-dopant the activity decreased. The improvement was suggested by a more positive onset potential (0.394 V vs. RHE), current density (0.231 mA cm-2 at 0.150 V vs. RHE), and faster kinetics (Tafel slope, b = 248 mV dec-1), and it may be due to the synergistic effect of (1) a sufficient amount of surface oxygen vacancies, and (2) a certain amount of plate-like particles composed of crystallites with well developed (0001) and (0001[combining macron]) facets. Quite the contrary, the OER study showed that the introduction of Fe3+ ions into the ZnO crystal structure resulted in enhanced catalytic activity of all ZnO:Fe samples, compared to pure ZnO, probably due to the modified binding energy and an optimized band structure. With the maximal current density of 1.066 mA cm-2 at 2.216 V vs. RHE, an onset potential of 1.856 V vs. RHE, and the smallest potential difference between the OER and ORR (ΔE = 1.58 V), ZnO:10Fe may be considered a promising bifunctional catalyst toward the OER/ORR in moderately alkaline solution. This study demonstrates that the electrocatalytic activity of ZnO:Fe strongly depends on the defect chemistry and consequently the band structure. Along with providing fundamental insight into the electrocatalytic activity of ZnO:Fe, the study also indicates an optimal stoichiometry for enhanced bifunctional activity toward the OER/ORR, compared to pure ZnO.

Surfactant-assisted microwave processing of ZnO particles: a simple way for designing the surface-to-bulk defect ratio and improving photo(electro)catalytic properties.

ZnO nanopowders were produced using microwave processing of a precipitate and applied as a photoanode for photoelectrochemical water splitting. Two different surfactants, cetyltrimethylammonium bromide (CTAB) as the cationic and Pluronic F127 as the non-ionic one, were employed to in situ adjust the surface-to-bulk defect ratio in the ZnO crystal structure and further to modify the photo(electro)catalytic activity of the ZnO photoanode. The crystal structure, morphological, textural, optical and photo(electro)catalytic properties of ZnO particles were studied in detail to explain the profound effects of the surfactants on the photoanode activity. The ZnO/CTAB photoanode displayed the highest photocurrent density of 27 mA g-1, compared to ZnO (10.4 mA g-1) and ZnO/F127 photoanodes (20 mA g-1) at 1.5 V vs. SCE in 0.1 M Na2SO4 under visible illumination of 90 mW cm-2. A significant shift of the overpotential toward lower values was also observed when photoanodes were illuminated. The highest shift of the overpotential, from 1.296 to 0.248 V vs. SCE, was recorded when the ZnO/CTAB photanode was illuminated. The ZnO/CTAB photoanode provides efficient charge transfer across the electrode/electrolyte interface, with a longer lifetime of photogenerated electron-hole pairs and reduced possibility of charge recombination. The photoconversion efficiency was improved from 1.4% for ZnO and 0.9% for ZnO/F127 to 4.2% for ZnO/CTAB at 0.510 mV. A simple procedure for the synthesis of ZnO particles with improved photo(electro)catalytic properties was established and it was found that even a small amount of CTAB used during processing of ZnO increases the surface-to-bulk defect ratio. Optimization of the surface-to-bulk defect ratio in ZnO materials enables increase of the absorption capacity for visible light, rendering of the recombination rate of the photogenerated pair, as well as increase of both the photocurrent density and photoconversion efficiency.

Poly(D,L-lactide-co-glycolide)/hydroxyapatite core-shell nanospheres. Part 3: properties of hydroxyapatite nano-rods and investigation of a distribution of the drug within the composite.

A step-by-step analysis of the formation and the drug loading of the poly(D,L-lactide-co-glycolide)/hydroxyapatite (PLGA/HAp) composite was carried out in a perspective of the following parameters: the structure, the morphology and the adsorption/desorption properties of the composite's bioceramic part. The authors demonstrated the importance of the material's capacity to form a fine dispersion of solid HAp particles, as an initial step, for the further loading of the drug and for the formation of the core-shell structures. The nanometer-sized rods of HAp have the capacity of ensuring a rapid adsorption and a controlled desorption of the drug from their surface, and they can act as a nucleating site for the formation of polymeric cores. Each component of this material was labeled with fluorescence dye, which enabled an insight into the distribution of the components in the core-shells that were obtained as the final outcome. Such an analysis showed a high level of uniformity among the cores enclosed within polymeric shells. From a practical perspective, the labeling of each component of the composite can be regarded as an additional functionality of the material: labeling can enable us to monitor its action during the healing process. This ability to be easily detected is expected to enhance the procedure for the controlled delivery of antibiotics after their local implantation of carriers loaded with the antibiotic and to provide more careful control over this process.

Poly(D,L-lactide-co-glycolide)/hydroxyapatite core-shell nanospheres. Part 1: A multifunctional system for controlled drug delivery.

Biodegradable poly(d,l-lactide-co-glycolide) (PLGA) and bioactive hydroxyapatite (HAp) are selected for the formation of a multifunctional system with the specific core-shell structure to be applied as a carrier of a drug. As a result, both components of PLGA/HAp core-shells are able to capture one part of the drug. Polymeric shells consisting of small nanospheres up to 20nm in size act as a matrix in which one part of the drug is dispersed. In the same time, ceramic cores are formed of rod-like hydroxyapatite particles at the surface of which another part of the drug is adsorbed onto the interface between the polymer and the ceramics. The content of the loaded drug, as well as the selected solvent/non-solvent system, have a crucial influence on the resulting PLGA/HAp morphology and, finally, unimodal distribution of core-shells is obtained. The redistribution of the drug between the organic and inorganic parts of the material is expected to provide an interesting contribution to the kinetics of the drug release resulting in non-typical two-step drug release.

Poly(D,L-lactide-co-glycolide)/hydroxyapatite core-shell nanosphere. Part 2: Simultaneous release of a drug and a prodrug (clindamycin and clindamycin phosphate).

The novel concept of a simultaneous, controlled release of a drug and a prodrug with different physico-chemical properties was applied in order to prolong the release period of antibiotics and estimate their high local concentrations, which are the necessary preconditions for the treatment of some chronic infection diseases. For this purpose poly(D,L-lactide-co-glycolide)/hydroxyapatite (PLGA/HAp) core-shell nanostructures were used as the carrier of clindamycin-base, as a drug, and clindamycin-2-phosphate, as a prodrug model. As a result, a two-step release was observed: the controlled release of the more soluble phosphate form and the sustained release of the less-soluble base form of clindamycin, resulting in a high overall concentration of the released drug during the period of 30 days in vitro. The HAp phase within the PLGA core-shells, applied as a drug carrier, delayed the process of the degradation of the polymer; however, the presence of the drug affected the process of degradation and this influence was the dominant factor in the control over the degradation of the polymer phase of PLGA/HAp and the consequent kinetics of the drug release.