Registry-based study of survivorship of cemented femoral components versus collared cementless femoral components in total hip arthroplasty in older patients with osteoarthritis.

Aims: In recent years, the use of a collared cementless femoral prosthesis has risen in popularity. The design intention of collared components is to transfer some load to the resected femoral calcar and prevent implant subsidence within the cancellous bone of the metaphysis. Conversely, the load transfer for a cemented femoral prosthesis depends on the cement-component and cement-bone interface interaction. The aim of our study was to compare the three most commonly used collared cementless components and the three most commonly used tapered polished cemented components in patients aged ≥ 75 years who have undergone a primary total hip arthroplasty (THA) for osteoarthritis (OA). Methods: Data from the Australian Orthopaedic Association National Joint Replacement Registry from 1 September 1999 to 31 December 2022 were analyzed. Collared cementless femoral components and cemented components were identified, and the three most commonly used components in each group were analyzed. We identified a total of 11,278 collared cementless components and 47,835 cemented components. Hazard ratios (HRs) from Cox proportional hazards models, adjusting for age and sex, were obtained to compare the revision rates between the groups. Results: From six months postoperatively onwards, patients aged ≥ 75 years undergoing primary THA with primary diagnosis of OA have a lower risk of all-cause revision with collared cementless components than with a polished tapered cemented component (HR 0.78 (95% confidence interval 0.64 to 0.96); p = 0.018). There is no difference in revision rate prior to six months. Conclusion: Patients aged ≥ 75 years with a primary diagnosis of OA have a significantly lower rate of revision with the most common collared cementless femoral component, compared with the most common polished tapered cemented components from six months postoperatively onwards. The lower revision rate is largely due to a reduction in revisions for fracture and infection.

Aseptic loosening around total joint replacement in humans is regulated by miR-1246 and miR-6089 via the Wnt signalling pathway.

BACKGROUND: Total joint replacement for osteoarthritis is one of the most successful surgical procedures in modern medicine. However, aseptic loosening continues to be a leading cause of revision arthroplasty. The diagnosis of aseptic loosening remains a challenge as patients are often asymptomatic until the late stages. MicroRNA (miRNA) has been demonstrated to be a useful diagnostic tool and has been successfully used in the diagnosis of other diseases. We aimed to identify differentially expressed miRNA in the plasma of patients with aseptic loosening. METHODS: Adult patients undergoing revision arthroplasty for aseptic loosening and age- and gender-matched controls were recruited. Samples of bone, tissue and blood were collected, and RNA sequencing was performed in 24 patients with aseptic loosening and 26 controls. Differentially expressed miRNA in plasma was matched to differentially expressed mRNA in periprosthetic bone and tissue. Western blot was used to validate protein expression. RESULTS: Seven miRNA was differentially expressed in the plasma of patients with osteolysis (logFC >|2|, adj-P < 0.05). Three thousand six hundred and eighty mRNA genes in bone and 427 mRNA genes in tissue samples of osteolysis patients were differentially expressed (logFC >|2|, adj-P < 0.05). Gene enrichment analysis and pathway analysis revealed two miRNA (miR-1246 and miR-6089) had multiple gene targets in the Wnt signalling pathway in the local bone and tissues which regulate bone metabolism. CONCLUSION: These results suggest that aseptic loosening may be regulated by miR-1246 and miR-6089 via the Wnt signalling pathway.

Are Kinematics an Indicator of Outcome After Total Knee Arthroplasty?

BACKGROUND: A proportion of total knee arthroplasty (TKA) patients are dissatisfied postoperatively, particularly with their ability to perform higher-demand activities including deep-kneeling and step-up where kinematic parameters are more demanding. The purpose of this study was to examine the relationship between knee kinematics of step-up and deep-kneeling and patient-reported outcome measures following TKA. METHODS: Sixty-four patients were included at minimum 1-year follow-up. Participants performed a step-up and deep-kneeling task which was imaged via single-plane fluoroscopy. 3-dimensional prosthesis computer-aided design models were registered to the fluoroscopy, yielding in-vivo kinematic data. Associations between kinematics and patient-reported outcome measures, including Oxford Knee Score, American Knee Society Score, surgical satisfaction, and pain were assessed using log-transformed step-wise linear regressions. RESULTS: A higher total Oxford Knee Score was associated with more external rotation and more adduction at maximal flexion during kneeling and more external rotation and minimum flexion during step-up. Improved American Knee Society Score was associated with increased internal-external rotation during step-up. Improved surgical satisfaction was associated with greater maximum flexion and more external rotation at maximal flexion during deep-kneeling and more femoral internal rotation at terminal extension during step-up. An improved pain score was associated with greater maximum flexion and more femoral external rotation during deep-kneeling, as well as greater internal femoral rotation during step-up. CONCLUSION: The ability to move through full flexion/extension range and end-of-range rotation is important kinematic parameters that influence patient-reported outcome measures. Implant designs and postoperative rehabilitation should continue to focus on achieving these kinematic targets for enhanced outcomes after TKA.

Union and Complication Rates After Total Wrist Arthrodesis: A Systematic Review and Meta-Analysis.

PURPOSE: Total wrist arthrodesis (TWA) has been performed using various techniques. We aimed to provide pooled prevalence estimates of union and complications of TWA by technique. A secondary aim was to provide estimates of union and complication rates by treatment of the carpometacarpal joint (CMCJ) in TWA using plates. Given the widespread adoption of wrist arthrodesis plates (WAP), we hypothesized that these implants would result in higher union and lower complication rates. We also hypothesized that TWA with CMCJ arthrodesis would improve these outcomes. METHODS: Online databases including PubMed, Medline, Embase, and Cochrane were searched. Studies reporting union and/or complication rates of 10 or more TWA performed with a similar technique (analyzed as bone graft only, bone graft with minimal fixation, intramedullary, augmented intramedullary, plate, WAP, and other) were included. Studies with fewer than 10 TWA, studies reporting TWA where union or complications could not be analyzed separately, and studies without union and complication rates were excluded. Data extraction was performed independently by two English-speaking reviewers with a translator where required. Pooled prevalence estimates were made using a random-effects meta-analysis model and presented as a percent prevalence with 95% confidence and prediction intervals. RESULTS: One hundred and thirty-six studies with a total of 3,517 patients and 3,969 TWA were analyzed. No differences in union and complication prevalence were observed between TWA techniques and in TWA with different treatments of the CMCJ using plates and WAP. CONCLUSION: Using meta-analysis, we found no difference in union and complication prevalence between TWA techniques and TWA with different treatments of the CMCJ with plates and WAP. It must be acknowledged that this research included low-quality studies with high heterogeneity, and confidence in the precision of the estimates is low. TYPE OF STUDY/LEVEL OF EVIDENCE: Prognostic IV.

The use of intra-articular vancomycin is safe in primary hip and knee arthroplasty.

Background: The use of a single dose of intra-articular antibiotic (IAA) has been reported in reducing the rate of prosthetic joint injection after total hip and knee arthroplasty. We examine the safety of IAA in primary hip and knee replacement surgery and the blood levels and joint fluid levels of vancomycin utilising this technique. Methods: From August to October 2021, 68 patients undergoing primary total joint arthroplasty (THA & TKA) were given 1g vancomycin intra-articularly (IA)after closure of the fascia. All patients received 2g cefazolin intravenously (IV) 30 min prior to the procedure as is our standard prophylaxis, and 21 of the patients (IA + IV) were also administered an additional 1 gm vancomycin IV. Post-operative blood vancomycin, creatinine land eGFR level monitoring was performed d1 and d3. To determine the post-operative intra-articular vancomycin levels, surgical drain fluid was sampled at day 1 and 2, in 10 patients. Results: All patients had serum vancomycin levels measured on day 1 and 3. In the group where vancomycin was injected after fascial closure, the average blood vancomycin level day 1 was 5.2 µg/ml (range 2.0-10.9) and day 3 was <1.4 µg/ml. The average pre-op creatinine levels were 69.4 µmol/L (56.1-82.6) compared to 70.2 µmol/L (57.0-83.4) on day 1 and 66.1 µmol/L (52.6-79.6) on day 3, (p = 0.663). The average pre-op eGFR levels (ml/min/1.73 m2) were 82.2 (76.0-88.3) compared to 81.7 (75.6-87.8) on day 1 and 83.0 (76.8-89.2) on day 3 (p = 0.736). Samples of joint fluid aspirated from surgical drains on day 1 and day 2 showed average vancomycin levels of 224 µg/ml and 51 µg/ml respectively, significantly higher than the MIC for Staph aureus. Conclusions: The use of intra-articular vancomycin is safe in primary TJA, with no renal damage and delivers levels within the joint which are highly therapeutic for at least 48 h post injection.

Biomechanical Performance of Total Wrist Arthrodesis Plates With and Without Arthrodesis of the Carpometacarpal Joint.

BACKGROUND: It is unknown whether total wrist arthrodesis (TWA) should be performed with or without arthrodesis of the carpometacarpal joint (CMCJ). The aim of this study is to compare CMCJ-spanning TWA plates using 3D printed wrist arthrodesis model with and without arthrodesis of the CMCJ. METHODS: Total wrist arthrodesis plates mounted to 3D printed models were tested under a 4-N bending load at 4 Hz for 50 000 cycles, increased by 15% every 10 000 cycles until failure. RESULTS: Plates with arthrodesis CMCJ were stiffer and failed at a significantly greater load and number of cycles than plates mounted to models without CMCJ arthrodesis. The Synthes stainless steel locking TWA plate performed better than the Trimed plate applied to the model without CMCJ arthrodesis and the Acumed plate applied to the model with CMCJ arthrodesis. Based on these findings, we recommend arthrodesis of the CMCJ in TWA. CONCLUSIONS: Incorporation of the CMCJ in TWA may protect against plate failure. If arthrodesis of the CMCJ is not performed, plate removal should be considered before breakage occurs. LEVEL OF EVIDENCE: IV.

A Novel Approach of Customized Pelvic Implant Design Based on Symmetrical Analysis and 3D Printing.

In pelvic trauma patients, the mismatch of complex geometries between the pelvis and fixation implant is a fundamental cause of unstable and displaced pelvic ring disruption, in which secondary intervention is strongly considered. The geometrical matching in the current customized implant design and clinical practice is through the nonfractured hemi-pelvis for the fractured pelvis. This design philosophy overlooks the anatomical difference between the hemipelves, and further, the geometrical asymmetry at local area still remains unknown. This study analyzed the anatomical asymmetry of a patient's 3D pelvic models from 13 patients. The hemipelves of each patient were registered by using an iterative closet algorithm to an optimum position with minimum deviations. The high deviation regions were summarized between the hemipelves in each case, and a color map was drawn on a hemipelvis model that identified the areas that had a high possibility to be symmetrically different. A severe pelvic trauma case was used to comprehend the approach by designing a 3D printed implant. Each fracture was then registered to the mirrored uninjured hemipelvis by using the same algorithm, and customized fixation implants were designed with reference to the fractured model. The customized fixation plates showed that the implants had lower geometrical deviation when attached onto the re-stitched fracture side than onto the mirrored nonfractured bone. These results indicate that the symmetrical analysis of bone anatomy and the deviation color map can assist with implant selection and customized implant design given the geometrical difference between symmetrical bones. The novel approach provides a scientific reference that improves the accuracy and overall standard of 3D printed implants.

Diabetes mellitus is a potential risk factor for aseptic loosening around hip and knee arthroplasty.

BACKGROUND: Aseptic loosening is a leading cause of revision following total hip and knee arthroplasty which is caused by chronic inflammation around the prosthesis. Diabetes mellitus causes systemic inflammatory changes which could increase the risk of aseptic loosening. This study investigated the association between diabetes mellitus and aseptic loosening around hip and knee arthroplasty. METHODS: A case-control study was conducted at a single arthroplasty centre over the seven-year period of January 2015 to December 2021. Cases were defined as any adult patient undergoing revision hip or knee arthroplasty for aseptic loosening. Controls were randomly selected patients undergoing primary total hip or knee arthroplasty during the same period at a 1:4 ratio. Risk factors were compared between the two groups. RESULTS: A total of 440 patients were included in our study - 88 in the aseptic loosening group and 352 patients in the control group. The odds of having diabetes mellitus in the aseptic loosening group was 2.78 (95%CI 1.31-5.92, P = 0.01). Other risk factors were not significantly different between the two groups. CONCLUSIONS: The incidence of diabetes mellitus is significantly greater in patients undergoing revision arthroplasty for aseptic loosening. Further research is required to explore whether this association is indeed causative.

Antibiotic utilisation in primary and revision total hip replacement patients: A registry linkage cohort study of 106 253 patients using the Australian Orthopaedic Association National Joint Replacement Registry.

PURPOSE: Infection is a major complication following joint replacement (JR) surgery. However, little data exist regarding antibiotic utilisation following primary JR and how use changes with subsequent revision surgery. This study aimed to examine variation in antibiotic utilisation rates before and after hip replacement surgery in those revised for infection, revised for other reasons and those without revision. METHODS: This retrospective cohort analysis used linked data from the Australian Orthopaedic Association National Joint Replacement Registry and Australian Government Pharmaceutical Benefits Scheme. Patients were included if undergoing total hip replacement (THR) for osteoarthritis in private hospitals between 2002 and 2017. Three groups were examined: primary THR with no subsequent revision (n = 102 577), primary THR with a subsequent revision for reasons other than periprosthetic joint infection (PJI) (n = 3156) and primary THR with a subsequent revision for PJI (n = 520). Monthly antibiotic utilisation rates and prevalence rate ratios (PRRs) with 95% confidence intervals (CIs) were calculated in the 2 years pre- and post-THR. RESULTS: Prior to primary THR antibiotic utilisation was 9%-10%. After primary THR, antibiotic utilisation rates were higher among patients revised for PJI (PRR 1.69, 95% CI 1.60-1.79) compared to non-revised patients, while the utilisation rate was lower in patients revised for reasons other than infection (PRR 0.96, 95% CI 0.93-0.98). For those revised for infection, antibiotic utilisation post-revision surgery was two times higher than those revised for other reasons (PRR 2.16, 95% CI 2.08-2.23). Utilisation of injectable antibiotics including, vancomycin, flucloxacillin and cephazolin was higher in those revised for PJI patients 0-2 weeks following surgery but not in those revised for other reasons compared to the non-revised group. CONCLUSIONS: Ongoing antibiotic utilisation after primary surgery may be an early signal of problems with the THR and should be a prompt for primary care physicians to refer patients to specialists for further appropriate investigations and management.

Comparison of 2 open-sourced 3-dimensional modeling techniques for orthopaedic application.

Objectives: Although 3-dimensional (3D) printing is becoming more widely adopted for clinical applications, it is yet to be accepted as part of standard practice. One of the key applications of this technology is orthopaedic surgical planning for urgent trauma cases. Anatomically accurate replicas of patients' fracture models can be produced to guide intervention. These high-quality models facilitate the design and printing of patient-specific implants and surgical devices. Therefore, a fast and accurate workflow will help orthopaedic surgeons to generate high-quality 3D printable models of complex fractures. Currently, there is a lack of access to an uncomplicated and inexpensive workflow. Methods: Using patient DICOM data sets (n = 13), we devised a novel, simple, open-source, and rapid modeling process using Drishti software and compared its efficacy and data storage with the 3D Slicer image computing platform. We imported the computed tomography image directory acquired from patients into the software to isolate the model of bone surface from surrounding soft tissue using the minimum functions. One pelvic fracture case was further integrated into the customized implant design practice to demonstrate the compatibility of the 3D models generated from Drishti. Results: The data sizes of the generated 3D models and the processing files that represent the original DICOM of Drishti are on average 27% and 12% smaller than that of 3D Slicer, respectively (both P < 0.05). The time frame needed to reach the stage of viewing the 3D bone model and the exporting of the data of Drishti is 39% and 38% faster than that of 3D Slicer, respectively (both P < 0.05). We also constructed a virtual model using third-party software to trial the implant design. Conclusions: Drishti is more suitable for urgent trauma cases that require fast and efficient 3D bone reconstruction with less hardware requirement. 3D Slicer performs better at quantitative preoperative planning and multilayer segmentation. Both software platforms are compatible with third-party programs used to produce customized implants that could be useful for surgical training. Level of Evidence: Level V.

Comparison of Prognostic Value of 10 Biochemical Indices at Admission for Prediction Postoperative Myocardial Injury and Hospital Mortality in Patients with Osteoporotic Hip Fracture.

Aim: To evaluate the prognostic impact at admission of 10 biochemical indices for prediction postoperative myocardial injury (PMI) and/or hospital death in hip fracture (HF) patients. Methods: In 1273 consecutive patients with HF (mean age 82.9 ± 8.7 years, 73.5% women), clinical and laboratory parameters were collected prospectively, and outcomes were recorded. Multiple logistic regression and receiver-operating characteristic analyses (the area under the curve, AUC) were preformed, the number needed to predict (NNP) outcome was calculated. Results: Age ≥ 80 years and IHD were the most prominent clinical factors associated with both PMI (with cardiac troponin I rise) and in-hospital death. PMI occurred in 555 (43.6%) patients and contributed to 80.3% (49/61) of all deaths (mortality rate 8.8% vs. 1.9% in non-PMI patients). The most accurate biochemical predictive markers were parathyroid hormone > 6.8 pmol/L, urea > 7.5 mmol/L, 25(OH)vitamin D < 25 nmol/L, albumin < 33 g/L, and ratios gamma-glutamyl transferase (GGT) to alanine aminotransferase > 2.5, urea/albumin ≥ 2.0 and GGT/albumin ≥ 7.0; the AUC for developing PMI ranged between 0.782 and 0.742 (NNP: 1.84−2.13), the AUC for fatal outcome ranged from 0.803 to 0.722, (NNP: 3.77−9.52). Conclusions: In HF patients, easily accessible biochemical indices at admission substantially improve prediction of hospital outcomes, especially in the aged >80 years with IHD.

Gallium-Strontium Phosphate Conversion Coatings for Promoting Infection Prevention and Biocompatibility of Magnesium for Orthopedic Applications.

Device-associated infections remain a clinical challenge. The common strategies to prevent bacterial infection are either toxic to healthy mammalian cells and tissue or involve high doses of antibiotics that can prompt long-term negative consequences. An antibiotic-free coating strategy to suppress bacterial growth is presented herein, which concurrently promotes bone cell growth and moderates the dissolution kinetics of resorbable magnesium (Mg) biomaterials. Pure Mg as a model biodegradable material was coated with gallium-doped strontium-phosphate through a chemical conversion process. Gallium was distributed in a gradual manner throughout the strontium-phosphate coating, with a compact structure and a gallium-rich surface. It was demonstrated that the coating protected the underlying Mg parts from significant degradation in minimal essential media at physiological conditions over 9 days. In terms of bacteria culture, the liberated gallium ions from the coatings upon Mg specimens, even though in minute quantities, inhibited the growth of Gram-positiveStaphylococcus aureus, Gram-negative Escherichia coli, andPseudomonas aeruginosa ─ key pathogens causing infection and early failure of the surgical implantations in orthopedics and trauma. More importantly, the gallium dopants displayed minimal interferences with the strontium-phosphate-based coating which boosted osteoblasts and undermined osteoclasts in in vitro co-cultures. This work provides a new strategy to prevent bacterial infection and control the degradation behavior of Mg-based orthopedic implants, while preserving osteogenic features of the devices.

An efficient hybrid method for 3D to 2D medical image registration.

PURPOSE: The purpose of this paper is to present a method for registration of 3D computed tomography to 2D single-plane fluoroscopy knee images to provide 3D motion information for knee joints. This 3D kinematic information has unique utility for examining joint kinematics in conditions such as ligament injury, osteoarthritis and after joint replacement. METHODS: We proposed a non-invasive rigid body image registration method which is based on two different multimodal similarity measures. This hybrid registration method helps to achieve a trade-off among different challenges including, time complexity and accuracy. RESULTS: We performed a number of experiments to evaluate the performance of the proposed method. The experimental results show that the proposed method is as accurate as one of the most recent registration methods while it is several times faster than that method. CONCLUSION: The proposed method is a non-invasive, fast and accurate registration method, which can provide 3D information for knee joint kinematic measurements. This information can be very helpful in improving the accuracy of diagnosis and providing targeted treatment.

What's old is best again Is anterior plating best for fixation of type-C pelvic fractures? A systematic review and meta-analysis.

BACKGROUND: Type-C pelvic fractures are a rare but potentially fatal injury that often leads to poor outcomes, despite surgical fixation. Many fixation methods are used but the optimal method remains contentious, with failure and complications common. This study compared outcomes for each fixation method. METHODS: A systematic review was conducted according to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA). A search of studies which reported on outcomes after surgically treated type-C pelvic fractures was undertaken. Data retrieved included fixation method, length of follow up, surgical revision, and complications rates (hardware breakage, post-operative outcomes, screw mal-positioning, screw loosening, loss of reduction and infection). Study quality was assessed using the Methodological Index for Non-Randomised Studies (MINORS). Pooled revision, outcome and complication rates were calculated using a quality-adjusted model in MetaXL 5.3. RESULTS: Fifty-two studies met the inclusion criteria representing 1567 patients and 7 fixation methods. The meta-analyses demonstrated high rates of 'less-than-good' outcomes for most fixation methods, with a higher rate for bilateral injuries (overall 23%; unilateral 21% v bilateral 41%). The mean pooled rate for surgical revision rate was 4%, hardware breakage 3%, screw mal-positioning 2%, screw loosening 3%, loss of reduction 5% and infection 4%. Each fixation method had different performance profiles; however, anterior plating outperformed all other fixation methods for patient outcomes, with a 'less-than-good' rate of just 7% vs the pooled mean of 23% and demonstrated at or below pooled mean rates for all complications except revision which was 5%. CONCLUSIONS: Post-operative outcomes for surgically treated type-C pelvic fractures revealed a 'less-than-good' pooled outcome rate of 23% and a revision rate of 4%. Anterior plates outperformed most other systems particularly for patient reported outcomes. Pooled revision, patient-reported outcome and complication rates for type-C pelvic fractures have not previously been reported and these data provide a benchmark for practice and future research.

Recommendations in the rehabilitation of patients undergoing hip abductor tendon repair: a systematic literature search and evidence based rehabilitation protocol.

INTRODUCTION: Advanced hip imaging and surgical findings have demonstrated that a common cause of greater trochanteric pain syndrome (GTPS) is hip abductor tendon (HAT) tears. Traditionally, these patients have been managed non-operatively, often with temporary pain relief. More recently, there has been an increase in published work presenting the results of surgical intervention. A variety of open and endoscopic transtendinous, transosseous and/or bone anchored suture surgical techniques have been reported, with and without the use of tendon augmentation for repair reinforcement. While patient outcomes have demonstrated improvements in pain, symptoms and function, post-operative rehabilitation guidelines are often vague and underreported, providing no guidance to therapists. MATERIALS AND METHODS: A systematic search of the literature was initially undertaken to identify published clinical studies on patients undergoing HAT repair, over a 3-year period up until May 2020. Following the application of strict inclusion and exclusion criteria, studies were identified and the detail relevant to rehabilitation was synthesized and presented. Published detail was combined with the authors clinical experience, with a detailed overview of rehabilitation proposed for this patient cohort. RESULTS: A total of 17 studies were included, reporting varied detail on components of rehabilitation including post-operative weight bearing (WB) restrictions, the initiation of passive/active hip range of motion (ROM) and resistance exercises. A detailed rehabilitation guide is proposed. CONCLUSION: In combining the current published literature on rehabilitation after HAT repair and our own clinical experience in the surgical management and post-operative rehabilitation of these patients, we present an evidence-based, structured rehabilitation protocol to better assist surgeons and therapists in treating these patients. This rehabilitation protocol has been implemented for several years through our institutions with encouraging published clinical outcomes.

Pharmacological prevention of renal ischemia-reperfusion injury in a rat model.

INTRODUCTION: Renal ischemia-reperfusion injury (IRI) can lead to significant morbidity and mortality. It remains a leading cause of acute kidney injury and is therefore an important issue in trauma and renal transplant surgery. Various pharmaceutical agents have been used in an attempt to dampen the harmful effects of IRI but few have been shown to be useful clinically. Riluzole, Lidocaine and Lamotrigine have been demonstrated to show anti-ischaemic properties in other organs; however, their use has not been tested in the kidneys. We investigated Riluzole, Lidocaine and Lamotrigine for their preventive effects of renal IRI using a rat model. METHODS: Winstar rats (n = 48) were divided into four groups (n = 12 per group)-three treatment groups and one control group. Riluzole, Lidocaine and Lamotrigine were given prior to renal ischemia only (IO) or IRI. The degree of ischemia was measured by glutathione levels and a TUNEL assay was used to measure DNA fragmentation. RESULTS: Riluzole, Lidocaine and Lamotrigine pre-treatment each resulted in statistically higher glutathione levels compared to controls (P = 0.002; P = 0.007 and P = 0.005, respectively). Riluzole and Lidocaine were also effective at preventing depletion of glutathione following IO (P = 0.007 and P = 0.014 respectively), while Lamotrigine was ineffective in IO (P = 0.71). The degree of DNA fragmentation seen on the TUNEL assay was markedly reduced in all three-drug groups in both IO and IRI. DISCUSSION: Riluzole, Lidocaine and Lamotrigine all have anti-ischaemic effects in the rat kidney and can have potential therapeutic implications.

Total wrist arthrodesis with and without arthrodesis of the carpoMetacarpal joint (WAWWAM): study protocol.

BACKGROUND: It is controversial whether or not the carpometacarpal joint (CMCJ) should be included in total wrist arthrodesis (TWA). Complications commonly occur at this site and studies examining its inclusion and exclusion are conflicting. A randomised clinical trial comparing wrist arthrodesis with CMCJ arthrodesis and spanning plate to wrist arthrodesis with CMCJ preservation and non-CMCJ spanning plate has not been performed. METHOD: A single centre randomised clinical trial including 120 adults with end-stage isolated wrist arthritis will be performed to compare TWA with and without the CMCJ included in the arthrodesis. The primary outcome is complications in the first post-operative year. Secondary outcomes are Disabilities of the Arm, Shoulder and Hand (DASH) score, Patient Rated Wrist Evaluation (PRWE) and grip strength measured at 1, 2 and 5 years. Late complications, return to work and satisfaction will also be recorded. DISCUSSION: It is unknown whether the CMCJ should be included in TWA. This trial will contribute to an improved understanding of optimal management of the CMCJ in total wrist arthrodesis. TRIAL REGISTRATION: This trial was prospectively registered with the Australia New Zealand Clinical Trials Registry with identifying number ACTRN12621000169842 on the 16th February 2021. WHO: U1111-12626523. ANZCTR: ACTRN12621000169842.

Individuals with gluteal tendon repair display similar hip biomechanics to those of a healthy cohort during a sit-to-stand task.

BACKGROUND: Gluteal-tendon repair (GTR) is reported to be effective for relieving pain and improving clinical function in patients with gluteal-tendon tears. The sit-to-stand (STS) task is an important activity of daily living and is often used to assess functional capacity in clinical populations. Understanding if and how STS performance is altered in individuals with gluteal tendon repair may be an effective marker of GTR outcomes as well as a possible therapeutic target for post-operative rehabilitation. RESEARCH QUESTION: Do biomechanical parameters during STS differ between age- and sex-matched participants with and without gluteal-tendon repair? METHODS: 27 participants with a GTR and 29 healthy participants performed the STS task. Data were acquired using the three-dimensional motion capture system and forceplates. Outcomes of interest were task duration, rate of force development, trunk, pelvis, and hip joint angles, moments and powers. Differences were assessed using Generalised linear multivariate models and statistical parametric mapping. RESULTS: GTR patients performed the STS movement significantly slower (1.4+/- 0.40 s) compared to controls (1.1+/ -0.2 s) with a significantly lower rate of force development (35.1+/- 5.7 N/kg/ms vs 30.3+/- 8.5 N/kg/ms). There were no group differences for hip, pelvis, or trunk angle over the movement cycle or for maximal or minimal values. Furthermore, there were no significant differences detected in hip joint kinetics. However, there appeared to be substantial between-subject variability indicating different patient-specific movements patterns. SIGNIFICANCE: Individuals with a GTR performed the STS task about 20 % slower than healthy controls with a lower rate of force development. The individual variations indicate that participants likely employed different movement strategies to achieve STS. While the lack of differences between groups could suggest that GTR helps restore function and corrects the proposed underlying aetiology, it is possible that the STS task was not sufficiently challenging to discriminate between groups.

A critical analysis of the 8th edition TNM staging for head and neck cutaneous squamous cell carcinoma with lymph node metastases and comparison to N1S3 stage and ITEM risk score: A multicenter study.

BACKGROUND AND OBJECTIVES: We performed a critical analysis of the 8th edition American Joint Committee on Cancer (AJCC) staging for head and neck cutaneous squamous cell carcinoma (HNcSCC) with nodal metastases and compared the performance to the N1S3 and ITEM systems. METHODS: Multicenter study of 990 patients with metastatic HNcSCC treated with curative intent. The end points of interest were disease-specific (DSS) and overall survival (OS). Model fit was evaluated using Harrell's Concordance Index (C-index), proportion of variation explained (PVE), Akaike information criterion, and Bayesian information criterion. RESULTS: N1S3 and ITEM demonstrated good distribution into risk categories in contrast to the AJCC system, which classified the majority (90.6%) of patients as N2-3 and Stage IV due to the high rate of extranodal extension. The N2c and N3a categories appeared redundant. There was considerable discordance between systems in risk allocation on an individual patient basis. N1S3 was the best performed (DSS: C-index 0.62, PVE 10.9%; OS: C-index 0.59, PVE 4.5%), albeit with relatively poor predictive value. CONCLUSIONS: The AJCC N category and tumor node metastasis stage have poor patient distribution and predictive performance in HNcSCC. The AJCC stage, N1S3, and ITEM score all provide limited prognostic information based on objective measures highlighting the need to develop a staging system specific to HNcSCC.