Stacking architecture for collimated backlight using cylindrical lens sheet with linear light sources or edge-lit/direct-lit BLU.

Highly collimated and directional backlights are essential for realizing advanced display technologies such as autostereoscopic 3D displays. Previously reported collimated backlights, either edge-lit or direct-lit, in general still suffer unsatisfactory form factors, directivity, uniformity, or crosstalk etc. In this work, we report a simple stacking architecture for the highly collimated and uniform backlights, by combining linear light source arrays and carefully designed cylindrical lens arrays. Experiments were conducted to validate the design and simulation, using the conventional edge-lit backlight or the direct-lit mini-LED (mLED) arrays as light sources, the NiFe (stainless steel) barrier sheets, and cylindrical lens arrays fabricated by molding. Highly collimated backlights with small angular divergence of ±1.45°âˆ¼±2.61°, decent uniformity of 93-96%, and minimal larger-angle sidelobes in emission patterns were achieved with controlled divergence of the light source and optimization of lens designs. The architecture reported here provides a convenient way to convert available backlight sources into a highly collimated backlight, and the use of optically reflective barrier also helps recycle light energy and enhance the luminance. The results of this work are believed to provide a facile approach for display technologies requiring highly collimated backlights.

Technological process optimization and measurement of image quality of the electrically bifocal metalens.

This Letter describes the design procedure and process optimization of the electrically bifocal metalens. In our design, horizontal and vertical polarization is manipulated by applying a suitable voltage to a twisted nematic liquid crystal (TN-LC) cell. Each nanostructure is designed to be a rectangular prism, making different polarizations of light experience various phase delays, thus causing bi-focus. We selected lithographical methods to fabricate our metalens because of the minimum physical size, which can be as small as 50 nm, and the maximum aspect ratio, which is as high as 15. Furthermore, to increase the tolerance and make the sidewall vertical and smooth, we coated different characteristics of photoresist sensitivity to the upper and lower layers. After the development, the mushroom-type photoresist makes Ni easier to strip while in the lift-off process, thus increasing the quality of the whole metalens. Our experiment shows that the focal lengths and focusing efficiencies corresponding to the two polarizations are similar to the simulation results. The proposed electrically modulated bifocal metalens can be utilized in different applications and combined with other optical components.

Time-Effective Simulation Methodology for Broadband Achromatic Metalens Using Deep Neural Networks.

Metasurface has demonstrated potential and novel optical properties in previous research. The prevailing method of designing a macroscale metasurface is based on the local periodic approximation. Such a method relies on the pre-calculated data library, including phase delay and transmittance of the nanostructure, which is rigorously calculated by the electromagnetic simulation. However, it is usually time-consuming to design a complex metasurface such as broadband achromatic metalens due the required huge data library. This paper combined different numbers of nanofins and used deep neural networks to train our data library, and the well-trained model predicted approximately ten times more data points, which show a higher transmission for designing a broadband achromatic metalens. The results showed that the focusing efficiency of designed metalens using the augmented library is up to 45%, which is higher than that using the original library over the visible spectrum. We demonstrated that the proposed method is time-effective and accurate enough to design complex electromagnetic problems.

Ultrawide-angle and high-efficiency metalens in hexagonal arrangement.

Wide-angle optical systems play a vital role in imaging applications and have been researched for many years. In traditional lenses, attaining a wide field of view (FOV) by using a single optical component is difficult because these lenses have crucial aberrations. In this study, we developed a wide-angle metalens with a numerical aperture of 0.25 that provided a diffraction-limited FOV of over 170° for a wavelength of 532 nm without the need for image stitching or multiple lenses. The designed wide-angle metalens is free of aberration and polarization, and its full width of half maximum is close to the diffraction limit at all angles. Moreover, the metalens which is designed through a hexagonal arrangement exhibits higher focusing efficiency at all angles than most-seen square arrangement. The focusing efficiencies are as high as 82% at a normal incident and 45% at an incident of 85°. Compared with traditional optical components, the proposed metalens exhibits higher FOV and provides a more satisfactory image quality because of aberration correction. Because of the advantages of the proposed metalens, which are difficult to achieve for a traditional single lens, it has the potential to be applied in camera systems and virtual and augmented reality.

Three-stage full-wave simulation architecture for in-depth analysis of microspheres in microscopy.

Over a decade, considerable development has been achieved in microsphere microscopy; the popularity of this method is attributable to its compatibility with biomedical applications. Although microscopy has been used extensively, insufficient analyses and simulation approaches capable of explaining the experimental observations have hampered its theoretical development. In this paper, a three-stage full-wave simulation architecture has been presented for the in-depth analysis of the imaging properties of microspheres. This simulation architecture consists of forward and backward propagation mechanisms, following the concept of geometric optics and strictly complying to wave optics at each stage. Three numerical simulation methods, including FDTD, NTFF, and ASPW, are integrated into this simulation architecture to encompass near-field and far-field behaviors and relieve the computational burden. We validated this architecture by comparing our simulation results with the experimental data provided in literature. The results confirmed that the proposed architecture exhibits high consistency both qualitatively and quantitatively. By using this architecture, we demonstrated the near-field effect of the samples on the resolution and provided evidence to explain the conflicts in literature. Moreover, the flexibility and versatility of the proposed architecture in modeling allow adaptation to various scenarios in microsphere microscopy. The results of this study, as an imaging analysis and system design platform, may facilitate the development of microsphere microscopy for biomedical imaging, wafer inspection, and other potential applications.

Electrically modulated varifocal metalens combined with twisted nematic liquid crystals.

Focus-tunable lenses are indispensable to optical systems. This paper proposes an electrically modulated varifocal metalens combined with twisted nematic liquid crystals. In our design, a metalens is employed to focus on different points depending on the polarization state of incident light. We demonstrated that the varifocal metalens has a sub-millisecond response time. Furthermore, the numerical aperture of both the first and second focal points can be customized to achieve a wide range of 0.2-0.7. Moreover, the full width at half maximum approached the diffraction limit at multiple focal points. Because of the advantages of our proposed electrically modulated metalens, it has the potential for application in optical technology and biomedical science, both of which require high image quality and a rapid response time.

Design of a high-efficiency train headlamp with low power consumption using dual half-parabolic aluminized reflectors.

We propose a train headlamp system using dual half-circular parabolic aluminized reflectors. Each half-circular reflector contains five high-efficiency and small-package light-emitting diode (LED) chips, and the halves are 180° rotationally symmetric. For traffic safety, the headlamp satisfies the Code of Federal Regulations. To predict the pattern of illumination, an analytical derivation is developed for the optical path of a ray that is perpendicular to and emitted from the center of an LED chip. This ray represents the main ray emitted from the LED chip and is located at the maximum illuminance of the spot projected by the LED source onto a screen. We then analyze the design systematically to determine the locations of the LED chips in the reflector that minimize electricity consumption while satisfying reliability constraints associated with traffic safety. Compared to a typical train headlamp system with an incandescent or halogen lamp needing several hundred watts, the proposed system only uses 20.18 W to achieve the luminous intensity requirements.

Wide-angle and ultrathin camera module using a curved hexagonal microlens array and all spherical surfaces.

In this paper, we propose a wide-angle and thin camera module integrating the principles of an insect's compound eye and the human eye, mimicking them with a curved hexagonal microlens array and a hemispherical lens, respectively. Compared to typical mobile phone cameras with more than four lenses and a limited full field of view (FFOV), the proposed system uses only two lenses to achieve a wide FFOV. Furthermore, the thickness of our proposed system is only 2.7 mm. It has an f-number of 2.07, an image diameter of 4.032 mm, and a diagonal FFOV of 136°. The results showed good image quality with a modulation transfer function above 0.3 at a Nyquist frequency of 166 cycles/mm.

Wide-angle camera with multichannel architecture using microlenses on a curved surface.

We propose a multichannel imaging system that combines the principles of an insect's compound eye and the human eye. The optical system enables a reduction in track length of the imaging device to achieve miniaturization. The multichannel structure is achieved by a curved microlens array, and a Hypergon lens is used as the main lens to simulate the human eye, achieving large field of view (FOV). With this architecture, each microlens of the array transmits a segment of the overall FOV. The partial images are recorded in separate channels and stitched together to form the final image of the whole FOV by image processing. The design is 2.7 mm thick, with 59 channels; the 100°×80° full FOV is optimized using ZEMAX ray-tracing software on an image plane. The image plane size is 4.53 mm×3.29 mm. Given the recent progress in the fabrication of microlenses, this image system has the potential to be commercialized in the near future.

Polydimethylsiloxane coating on an ionic polymer metallic composite for a tunable focusing mirror.

An ionic polymer metallic composite (IPMC) can perform a bending deformation under an electric field by a small bias voltage. A roughening process is necessary and typically included in the IPMC fabrication. Roughening processes bring several advantages, including better metal adhesion and actuation performance. However, the resulting large surface roughness is an obstacle for optical applications. In this paper, we coated polydimethylsiloxane to improve the surface roughness of IPMC. The improved surface roughness is around 28 nm versus tens of micrometers with an uncoated IPMC. The surface-improved IPMC achieved focusing power of 77 diopters under a 7 V bias voltage. We also found that the lifetime in atmosphere is 30 times longer than that of the nonimproved IPMC. Compared with other popular focusing techniques, such as liquid lenses or micromachined deformable mirrors, the driving voltage is at least one order of magnitude lower and the tunable range is two to three times larger. The effects of the surface-improved fabrication on reflectance, surface scattering, and actuation performance are also discussed. We demonstrate the surface-improved method to construct a patterned IPMC deformable membrane for optical applications.

Optical zoom module based on two deformable mirrors for mobile device applications.

In recent years, optical zoom functionality in mobile devices has been studied. Traditional zoom systems use motors to change separation of lenses to achieve the zoom function, but these systems result in long total length and high power consumption, which are not suitable for mobile devices. Adopting micromachined polymer deformable mirrors in zoom systems has the potential to reduce thickness and chromatic aberration. In this paper, we propose a 2× continuous optical zoom system with five-megapixel image sensors by using two deformable mirrors. In our design, the thickness of the zoom system is about 11 mm. The effective focal length ranges from 4.7 mm at a field angle of 52° to 9.4 mm. The f-number is 4.4 and 6.4 at the wide-angle and telephoto end, respectively.