Impact of reduced sampling frequency of illicit drug wastewater monitoring in the Netherlands.

Drug consumption estimates are traditionally based on surveys or information from police seizures. Alternatively, residues of illicit drugs in untreated wastewater (influent) can be used to calculate mass loads and subsequently estimate drug consumption in the community throughout the week. For this purpose, wastewater is commonly sampled for seven consecutive days within the Sewage analysis CORe group Europe (SCORE), while other sampling schemes may be implemented in long-term studies outside this consortium. The current study demonstrates how sampling frequency of illicit drug residues in the influent of wastewater treatment plants (WWTPs) affects the derived weekly average. Thirty WWTPs were sampled over the course of 12 years and influents were analyzed for five drugs (metabolites): 3,4-methylenedioxymethamphetamine (MDMA), methamphetamine, amphetamine, benzoylecgonine (a metabolite of cocaine), and 11-nor-9-Carboxy tetrahydrocannabinol (THC-COOH). Subsequently, small and large WWTPs were grouped with a threshold of 100,000 inhabitants. After data curation, standardized loads were calculated (mg/d per 1000 inhabitants). Weekly averages of loads of the drug residues were calculated based on six scenarios (sampling one to six weekdays) and compared to the weekly average in the control situation (sampling seven weekdays) in a Monte Carlo simulation. Results indicate that drug residues with more dynamic loads over a week require more frequent sampling. The analysis illustrates that a decreased sampling frequency (4 or 5 days per week) still leads to a representative weekly average for all drugs tested when a deviation up to a factor of 1.25 is deemed acceptable. However, knowledge on typical levels is necessary to define outliers. We therefore recommend to study dynamics in drug residue loads for WWTPs before reducing sampling frequency in long term monitoring programs.

Mapping consumptions and market size of cocaine, amphetamine and MDMA through wastewater analysis: A Dutch case study.

BACKGROUND AND AIMS: Illicit drug consumption is associated with public health effects and criminal activities. This study aimed to estimate Illicit drug consumption and annual market in the Netherlands from wastewater analysis of drug residues. METHODS: Residues of cocaine, amphetamine and 3,4-methylene dioxymethamphetamine (MDMA) were measured between 2015 and 2022 in 30 Dutch wastewater treatment plants serving both rural and urban populations. These wastewater treatment plants covered 20% of the total Dutch population. The Dutch annual retail market was estimated by extrapolating consumption to the total Dutch population, back-calculating consumption volume, correcting for drug purity and street price collected in voluntary checking services, and accounting for the correlation of consumption and urbanity. RESULTS: The per capita MDMA and cocaine consumption correlated positively with the urbanity of the wastewater treatment plant catchments with r2 of 31% and 64%, respectively. Amphetamine did not show a significant correlation with urbanity. The three studied drugs were conservatively estimated to cover an average annual market value of 903 (95% prediction interval 829 to 987) million Euro for the studied period. Market estimations from prevalence figures and interceptions of international trade were similar. CONCLUSIONS: Illicit drug consumption in the Netherlands appears to correlate positively with urban (in contrast to rural) areas. Wastewater analysis can be used to estimate the volume and monetary value of illicit drug markets as a proof of concept.

Exploring Perfluoroalkyl and Polyfluoroalkyl Substance Presence and Potential Leaching from Reverse Osmosis Membranes: Implications for Drinking Water Treatment.

Reverse osmosis (RO) is increasingly used in drinking water production to effectively remove micropollutants, such as perfluoroalkyl and polyfluoroalkyl substances (PFAS). However, RO membranes themselves may contain PFAS, which can potentially leach into treated drinking water. Leaching experiments and direct total oxidizable precursor assays revealed the presence and leaching potential of PFOS (branched and linear), PFBA, PFHxA, PFNA, and PFOA in five selected commercial RO membranes. This resulted in the release of tens of milligrams of ΣPFAS per membrane element used in drinking water production. Depending on assumptions made regarding leaching kinetics and volume of produced water per membrane element, predicted concentrations of ΣPFAS in the produced water ranged from less than one up to hundreds of pg/L. These concentrations are two to four orders of magnitude lower than those currently observed in Dutch drinking waters. The origin of PFAS in the membranes remains unclear. Further research is needed to bridge the gap between the laboratory conditions as used in this study and the real-world conditions and for a full understanding of potential leaching scenarios. Such an understanding is critical for water producers using RO technologies to proactively manage and mitigate potential PFAS contamination.

Combining Passive Sampling and Dosing to Unravel the Contribution of Hydrophobic Organic Contaminants to Sediment Ecotoxicity.

Contaminated sediments are ubiquitous repositories of pollutants and cause substantial environmental risks. Results of sediment bioassays remain difficult to interpret, however, as observed effects may be caused by a variety of (un)known stressors. This study aimed therefore to isolate the effects of hydrophobic organic contaminants from other (non)chemical stressors present in contaminated sediments, by employing a newly developed passive sampling-passive dosing (PSPD) test. The results showed that equilibrium partitioning between pesticides or polyaromatic hydrocarbons (PAHs) in contaminated sediments and a silicone rubber (SR) passive sampler was achieved after 1-3 days. Chlorpyrifos concentrations in pore water of spiked sediment matched very well with concentrations released from the SR into an aqueous test medium, showing that SR can serve as a passive dosing device. Subjecting the 96 h PSPD laboratory bioassay with nonbiting midge (Chironomus riparius) larvae to field-collected sediments showed that at two locations, concentrations of the hydrophobic organic contaminant mixtures were high enough to affect the test organisms. In conclusion, the developed PSPD test was able to isolate the effects of hydrophobic organic contaminants and provides a promising simplified building block for a suite of PSPD tests that after further validation could be used to unravel the contribution of hydrophobic organic chemicals to sediment ecotoxicity.

Research Priorities for the Environmental Risk Assessment of Per- and Polyfluorinated Substances.

Per- and polyfluorinated substances (PFAS) are a group of thousands of ubiquitously applied persistent industrial chemicals. The field of PFAS environmental research is developing rapidly, but suffers from substantial biases toward specific compounds, environmental compartments, and organisms. The aim of our study was therefore to highlight current developments and to identify knowledge gaps and subsequent research needs that would contribute to a comprehensive environmental risk assessment for PFAS. To this end, we consulted the open literature and databases and found that knowledge of the environmental fate of PFAS is based on the analysis of <1% of the compounds categorized as PFAS. Moreover, soils and suspended particulate matter remain largely understudied. The bioavailability, bioaccumulation, and food web transfer studies of PFAS also focus on a very limited number of compounds and are biased toward aquatic biota, predominantly fish, and less frequently aquatic invertebrates and macrophytes. The available ecotoxicity data revealed that only a few PFAS have been well studied for their environmental hazards, and that PFAS ecotoxicity data are also strongly biased toward aquatic organisms. Ecotoxicity studies in the terrestrial environment are needed, as well as chronic, multigenerational, and community ecotoxicity research, in light of the persistency and bioaccumulation of PFAS. Finally, we identified an urgent need to unravel the relationships among sorption, bioaccumulation, and ecotoxicity on the one hand and molecular descriptors of PFAS chemical structures and physicochemical properties on the other, to allow predictions of exposure, bioaccumulation, and toxicity. Environ Toxicol Chem 2023;42:2302-2316. © 2023 The Authors. Environmental Toxicology and Chemistry published by Wiley Periodicals LLC on behalf of SETAC.

Forever legacies? Profiling historical PFAS contamination and current influence on groundwater used for drinking water.

A wide range of PFAS residues were studied in an aquifer used for drinking water production which was affected by historical PFAS contamination from a landfill and military camp. Samples were taken at three monitoring and four pumping wells at different depths ranging from 33 to 147 m below the land surface and analysed for a series of 53 PFAS (C2-C14) and PFAS precursors (C4-C24). A comparison of results to earlier research from 2013, with a more limited range of PFAS, showed decreasing concentrations and migration of PFAS with increasing depth and distance from the contamination source. The PFAS profile and branched/linear isomer ratio are used as source characterization tools. The landfill was confirmed to contaminate the groundwater in both monitoring wells, while the military camp was indicated as a probable source for PFAS observed in the deep sampling points of one of the monitoring wells. Pumping wells used to produce drinking water are not yet affected by these two PFAS sources. In one of the four sampled pumping wells, a different PFAS profile and isomer pattern was observed, which indicated a different but yet unknown source. This work shows the necessity of implementing regular screening to identify potential (historical) PFAS sources to be able to prevent future contaminant migration nearby and towards drinking water abstraction wells.

Occurrence, Fate, and Related Health Risks of PFAS in Raw and Produced Drinking Water.

This study investigates human exposure to per- and polyfluoroalkyl substances (PFAS) via drinking water and evaluates human health risks. An analytical method for 56 target PFAS, including ultrashort-chain (C2-C3) and branched isomers, was developed. The limit of detection (LOD) ranged from 0.009 to 0.1 ng/L, except for trifluoroacetic-acid and perfluoropropanoic-acid with higher LODs of 35 and 0.24 ng/L, respectively. The method was applied to raw and produced drinking water from 18 Dutch locations, including groundwater or surface water as source, and applied various treatment processes. Ultrashort-chain (300 to 1100 ng/L) followed by the group of perfluoroalkyl-carboxylic-acids (PFCA, ≥C4) (0.4 to 95.1 ng/L) were dominant. PFCA and perfluoroalkyl-sulfonic-acid (≥C4), including precursors, showed significantly higher levels in drinking water produced from surface water. However, no significant difference was found for ultrashort PFAS, indicating the need for groundwater protection. Negative removal of PFAS occasionally observed for advanced treatment indicates desorption and/or degradation of precursors. The proportion of branched isomers was higher in raw and produced drinking water as compared to industrial production. Drinking water produced from surface water, except for a few locations, exceed non-binding provisional guideline values proposed; however, all produced drinking waters met the recent soon-to-be binding drinking-water-directive requirements.

Microplastic discharge from a wastewater treatment plant: long term monitoring to compare two analytical techniques, LDIR and optical microscopy while also assessing the removal efficiency of a bubble curtain.

In this study we compare two parallel analytical methods while also testing a microplastics mitigation method. We assess the effectiveness of a bubble curtain to reduce microplastics in a wastewater treatment plant (WWTP)-effluent canal during the course of six months (>70 samples) using two analytical techniques: laser direct infrared (LDIR) and optical microscopy (OM) covering a size range of 0.02 to 5 mm. Comparison of the two analytical strategies shows similar trends, fluctuations, and correlating particle and fibre numbers. However, absolute values of particles differ, and the strategies provide different levels of information: LDIR is capable of identifying the plastic type as well as shape, while OM cannot determine the plastic type. Furthermore LIDR has a lower size limit (10-20 µm) than OM (50 µm). While information obtained by OM in general is far less detailed it is more affordable. This research also shows that the bubble curtain pilot does not have a measurable effect on the particle concentration. Possible effects of the curtain are hidden in the temporal variations. This research also reveals that individual samples show a large variation in particle numbers, illustrating that single measurements might give a poor representation of environmental particle number.

Triangulating Amsterdam's illicit stimulant use trends by wastewater analysis and recreational drug use monitoring.

Drug consumption estimates are of relevance because of public health effects as well as associated criminal activities. Wastewater analysis of drug residues enables the estimation of drug consumption and drug markets. Short-term and long-term trends of cocaine, MDMA (ecstasy), amphetamine (speed) and methamphetamine (crystal meth), were studied for the city of Amsterdam. MDMA (+41%) and cocaine (+26%) showed significantly higher weekend vs. week consumption, while no differences were observed for the other drugs. The consumption of MDMA, cocaine, amphetamine and methamphetamine significantly increased between 2011 and 2019. Weekly trends emerging from wastewater analyses were supported by qualitative and quantitative data from a recreational drug use monitoring scheme. However, information collected in panel interviews within nightlife networks and surveys among visitors of pubs, clubs and festivals only partially reflected the long term increase in consumption as registered from wastewater analysis. Furthermore, methamphetamine use was not well presented in survey data, panel studies and test service samples, but could be monitored trough wastewater analysis. This illustrates that wastewater analysis can function as an early warning if use and user groups are small or difficult to reach trough other forms of research. All in all, this study illustrates that wastewater-based epidemiology is complementary to research among user groups, and vice versa. These different types of information enable to connect observed trends in total drug consumption to behaviour of users and the social context in which the use takes place as well as validate qualitative signals about (increased) consumption of psychoactive substances. Such a multi angular approach to map the illicit drug situation on local or regional scale can provide valuable information for public health.

Occurrence, hazard, and risk of psychopharmaceuticals and illicit drugs in European surface waters.

This study aimed to provide insights into the risk posed by psychopharmaceuticals and illicit drugs in European surface waters, and to identify current knowledge gaps hampering this risk assessment. First, the availability and quality of data on the concentrations of psychopharmaceuticals and illicit drugs in surface waters (occurrence) and on the toxicity to aquatic organisms (hazard) were reviewed. If both occurrence and ecotoxicity data were available, risk quotients (risk) were calculated. Where abundant ecotoxicity data were available, a species sensitivity distribution (SSD) was constructed, from which the hazardous concentration for 5% of the species (HC5) was derived, allowing to derive integrated multi-species risks. A total of 702 compounds were categorised as psychopharmaceuticals and illicit drugs based on a combination of all 502 anatomical therapeutic class (ATC) 'N' pharmaceuticals and a list of illicit drugs according to the Dutch Opium Act. Of these, 343 (49%) returned occurrence data, while only 105 (15%) returned ecotoxicity data. Moreover, many ecotoxicity tests used irrelevant endpoints for neurologically active compounds, such as mortality, which may underestimate the hazard of psychopharmaceuticals. Due to data limitations, risks could only be assessed for 87 (12%) compounds, with 23 (3.3%) compounds indicating a potential risk, and several highly prescribed drugs returned neither occurrence nor ecotoxicity data. Primary bottlenecks in risk calculation included the lack of ecotoxicity data, a lack of diversity of test species and ecotoxicological end points, and large disparities between well studied and understudied compounds for both occurrence and toxicity data. This study identified which compounds merit concern, as well as the many compounds that lack the data for any calculation of risk, driving research priorities. Despite the large knowledge gaps, we concluded that the presence of a substantial part (26%) of data-rich psychopharmaceuticals in surface waters present an ecological risk for aquatic non-target organisms.

Fate of microplastics in the drinking water production.

Microplastics are ubiquitous and consequently enter drinking water treatment plants. Knowledge of the microplastic fate in drinking water production is still very limited, although explorative studies have shown tap water contains low contents of microplastics. In this study, we measure microplastic concentrations in drinking water sources and assess the effectiveness of various drinking water treatment facilities to reduce the microplastic concentrations in water to gain insight into the fate of microplastics. Two analytical techniques, laser direct infrared spectroscopy (LDIR) and optical microscopy, have been applied to cover the particle size range from 20 µm to 5 mm. In total five different drinking water sites were investigated using four different types of raw water (groundwater, surface water, dune filtrate and riverbank filtrate) for drinking water production. This research shows that drinking water treatment removes the majority of microplastics and that concentration of microplastics larger than 20 µm in tap water is less than 2 microplastics particles per litre. Between the different raw water sources it is found that groundwater had by far the lowest microplastics concentrations (< 1.000 microplastics per m3) and the highest concentration was found in riverine water, up to 460.000 particles per m3, specifically in the Lek Canal () (a canal connected to the river Rhine). On average the most abundant plastics found are polyamide (PA, 33%), polyethylene terephthalate (PET, 15%), rubbers (10%), polyethylene (PE, 10%) and chlorinated polyethylene (CPE, 7%). This study also showed that natural treatment steps, such as dune infiltration and sedimentation, remove microplastics effectively. However, this may introduce an adverse effect where microplastics potentially accumulate in the sediment and environment.

Spatial and temporal assessment of crack cocaine use in 13 European cities through wastewater-based epidemiology.

Already in early 2000s, concerns have been growing in the EU about increasing use of cocaine and it is estimated that below 1 % of the population administer the drug by smoking crack cocaine. New available data suggests an increase in the use of crack cocaine and an increase in the number of crack cocaine users entering treatment has been reported in several European countries. Robust estimations of crack cocaine use are however not available yet. The use of crack cocaine has long been associated with severe adverse socio-economic conditions as well as mental health problems, such as suicide ideation and depression. The aim of this study was to assess spatial trends in population-normalized mass loads of crack cocaine biomarkers (i.e., anhydroecgonine and anhydroecgonine methyl ester) in 13 European cities in six countries (the Netherlands, Belgium, Ireland, Portugal, Spain and Italy). Furthermore, temporal trends over a five-year period were evaluated through the analysis of historic samples collected in the Netherlands. Finally, the stability of the crack cocaine biomarkers in wastewater was investigated through batch experiments. The samples were analyzed with a new developed and validated hydrophilic interaction liquid chromatography coupled to mass spectrometry method. Targeted crack cocaine biomarkers were found in all cities. Also, crack cocaine biomarker was detected in wastewater from 2017 to 2021 in the Netherlands, but no significance between the years were found. With respect to biomarker in-sample stability, AEME was found to be stable in wastewater. This study assessed crack cocaine use for the first time on a broad scale, both temporal and in cities across Europe, with wastewater-based epidemiology and it shows the importance of wastewater analysis to monitor community loads of crack cocaine use.

Retrospective suspect and non-target screening combined with similarity measures to prioritize MDMA and amphetamine synthesis markers in wastewater.

3,4-Methylenedioxymethamphetamine (MDMA) and amphetamine are commonly used psychoactive stimulants. Illegal manufacture of these substances, mainly located in the Netherlands and Belgium, generates large amounts of chemical waste which is disposed in the environment or released in sewer systems. Retrospective analysis of high-resolution mass spectrometry (HRMS) data was implemented to detect synthesis markers of MDMA and amphetamine production in wastewater samples. Specifically, suspect and non-target screening, combined with a prioritization approach based on similarity measures between detected features and mass loads of MDMA and amphetamine was implemented. Two hundred and thirty-five 24 h-composite wastewater samples collected from a treatment plant in the Netherlands between 2016 and 2018 were analyzed by liquid chromatography coupled to high-resolution mass spectrometry. Samples were initially separated into two groups (i.e., baseline consumption versus dumping) based on daily loads of MDMA and amphetamine. Significance testing and fold-changes were used to find differences between features in the two groups. Then, associations between peak areas of all features and MDMA or amphetamine loads were investigated across the whole time series using various measures (Euclidian distance, Pearson's correlation coefficient, Spearman's rank correlation coefficient, distance correlation and maximum information coefficient). This unsupervised and unbiased approach was used for prioritization of features and allowed the selection of 28 presumed markers of production of MDMA and amphetamine. These markers could potentially be used to detect dumps in sewer systems, help in determining the synthesis route and track down the waste in the environment.

Wastewater-based epidemiology for illicit drugs: A critical review on global data.

Illicit drug use is complex, hidden and often highly stigmatized behaviour, which brings a vast challenge for drug surveillance systems. Drug consumption can be estimated by measuring human excretion products in untreated wastewater, known as wastewater-based epidemiology (WBE). Over the last decade, the application of wastewater-based epidemiology to monitor illicit drug loads increased and WBE is currently applied on a global scale. Studies from over the globe are evaluated with regard to their sampling method, analytical accuracy and consumption calculation, aiming to further reduce relevant uncertainties in order to make reliable comparisons on a global level. Only a limited number is identified as high-quality studies, so further standardization of the WBE approach for illicit drugs is desired especially with regard to the sampling methodology. Only a fraction of the reviewed papers explicitly reports uncertainty ranges for their consumption data. Studies which had the highest reliability are recently published, indicating an improvement in reporting WBE data. Until now, WBE has not been used in large parts of Africa, nor in the Middle East and Russia. An overview of consumption data across the continents on commonly studied drugs (cocaine, MDMA, amphetamine and methamphetamine) is provided. Overall, high consumption rates are confirmed in the US, especially for cocaine and methamphetamine, while relatively low illicit drug consumption is reported in Asia.

Risk-based prioritization of suspects detected in riverine water using complementary chromatographic techniques.

Surface waters are widely used as drinking water sources and hence their quality needs to be continuously monitored. However, current routine monitoring programs are not comprehensive as they generally cover only a limited number of known pollutants and emerging contaminants. This study presents a risk-based approach combining suspect and non-target screening (NTS) to help extend the coverage of current monitoring schemes. In particular, the coverage of NTS was widened by combining three complementary separations modes: Reverse phase (RP), Hydrophilic interaction liquid chromatography (HILIC) and Mixed-mode chromatography (MMC). Suspect lists used were compiled from databases of relevant substances of very high concern (e.g., SVHCs) and the concentration of detected suspects was evaluated based on ionization efficiency prediction. Results show that suspect candidates can be prioritized based on their potential risk (i.e., hazard and exposure) by combining ionization efficiency-based concentration estimation, in vitro toxicity data or, if not available, structural alerts and QSAR.based toxicity predictions. The acquired information shows that NTS analyses have the potential to complement target analyses, allowing to update and adapt current monitoring programs, ultimately leading to improved monitoring of drinking water sources.

patRoon: open source software platform for environmental mass spectrometry based non-target screening.

Mass spectrometry based non-target analysis is increasingly adopted in environmental sciences to screen and identify numerous chemicals simultaneously in highly complex samples. However, current data processing software either lack functionality for environmental sciences, solve only part of the workflow, are not openly available and/or are restricted in input data formats. In this paper we present patRoon, a new R based open-source software platform, which provides comprehensive, fully tailored and straightforward non-target analysis workflows. This platform makes the use, evaluation and mixing of well-tested algorithms seamless by harmonizing various common (primarily open) software tools under a consistent interface. In addition, patRoon offers various functionality and strategies to simplify and perform automated processing of complex (environmental) data effectively. patRoon implements several effective optimization strategies to significantly reduce computational times. The ability of patRoon to perform time-efficient and automated non-target data annotation of environmental samples is demonstrated with a simple and reproducible workflow using open-access data of spiked samples from a drinking water treatment plant study. In addition, the ability to easily use, combine and evaluate different algorithms was demonstrated for three commonly used feature finding algorithms. This article, combined with already published works, demonstrate that patRoon helps make comprehensive (environmental) non-target analysis readily accessible to a wider community of researchers.

Shifting the imbalance: Intentional reuse of Dutch sewage effluent in sub-surface irrigation.

Worldwide, agricultural irrigation currently accounts for 69% of freshwater withdrawal. Countries with a temperate climate, such as the Netherlands, experience periodic freshwater shortages in agriculture. The pressure on available freshwater will increase due to climate change and a growing demand for freshwater by e.g. industrial activities. Possible alternative water resources are considered in order to meet the current and future water demand. In this study we explore where, and how much, sewage treatment plant (STP) effluent can directly be reused in agricultural sub-surface irrigation (SSI) during an average and a dry season scenario, for all active (335) Dutch STPs. SSI systems may have a higher water demand as part of the STP effluent is transported with groundwater flow, although aboveground irrigation has a loss of water due to interception. Furthermore, such aboveground irrigation systems provide direct contact of crops with irrigation water. SSI systems provide a soil barrier which may function as a filter and buffer zone. In the Dutch situation, direct intentional reuse of STP effluent can fulfill up to 25% of croplands SSI water demand present within a five-kilometer transport buffer from the STPs during an average season and 17% during a dry season. Hereto, respectively, 78% and 84% of the total available Dutch STP effluent would be used. Thus, the intentional direct STP effluent reuse in agricultural SSI has the potential to satisfy a significant amount of the agricultural water demand at a national scale, presuming responsible reuse: safe applications for humans and environment and no limiting effects on water availability for other actors.

Retention soil filters for the treatment of sewage treatment plant effluent and combined sewer overflow.

Retention soil filters (RSFs) are vertical flow constructed wetlands. They are mainly used for the treatment of combined sewer overflow or stormwater, and not operated during dry weather conditions. However, RSFs have been successfully tested as continuous post treatment for sewage treatment plant effluents. In this paper we present a new approach, namely dual usage of the retention soil filter. During dry weather the RSF is used for the polishing treatment of sewage treatment plant effluent and during overflow events, the retention soil filter treats the combined sewer overflow. This study was conducted at two pilot RSFs that were fed with sewage treatment effluent for four years. Removal of TOC, DOC, nutrients and 21 organic micropollutants was determined during six months at different sequences of regular effluent and overflow treatment conditions. TOC, DOC and nutrients, appearing in high concentration in combined sewer overflow, were effectively removed, and metformin and caffeine micropollutants showed >99% removal. Residues from this combined sewer treatment that were sorbed on filter material or stored in pore water were washed out directly after treatment when STP effluent infiltration was initiated. This effect declined within 20 h after combined sewer overflow treatment. Dry periods of 18 h between combined sewer and sewage treatment plant effluent feeding counteracted the wash out effects. The highest removal efficiency was found in the beginning of the feeding time of 28 h, indicating that shorter feeding cycles enhance the overall efficiency of the RSF. Finally, the results show that a single RSF system can successfully reduce emissions of TOC, DOC, nutrients and micropollutants to surface waters from two different emission pathways, i.e. from regular treated effluents and storm related sewer overflows. In conclusion, the dual usage of RSF is a promising approach and ready for upscaling and implementation.

Integration of target analyses, non-target screening and effect-based monitoring to assess OMP related water quality changes in drinking water treatment.

The ever-increasing production and use of chemicals lead to the occurrence of organic micro-pollutants (OMPs) in drinking water sources, and consequently the need for their removal during drinking water treatment. Due to the sheer number of OMPs, monitoring using targeted chemical analyses alone is not sufficient to assess drinking water quality as well as changes thereof during treatment. High-resolution mass spectrometry (HRMS) based non-target screening (NTS) as well as effect-based monitoring using bioassays are promising monitoring tools for a more complete assessment of water quality and treatment performance. Here, we developed a strategy that integrates data from chemical target analyses, NTS and bioassays. We applied it to the assessment of OMP related water quality changes at three drinking water treatment pilot installations. These installations included advanced oxidation processes, ultrafiltration in combination with reverse osmosis, and granular activated carbon filtration. OMPs relevant for the drinking water sector were spiked into the water treated in these installations. Target analyses, NTS and bioassays were performed on samples from all three installations. The NTS data was screened for predicted and known transformation products of the spike-in compounds. In parallel, trend profiles of NTS features were evaluated using multivariate analysis methods. Through integration of the chemical data with the biological effect-based results potential toxicity was accounted for during prioritization. Together, the synergy of the three analytical methods allowed the monitoring of OMPs and transformation products, as well as the integrative biological effects of the mixture of chemicals. Through efficient analysis, visualization and interpretation of complex data, the developed strategy enabled to assess water quality and the impact of water treatment from multiple perspectives. Such information could not be obtained by any of the three methods alone. The developed strategy thereby provides drinking water companies with an integrative tool for comprehensive water quality assessment.

In situ removal of four organic micropollutants in a small river determined by monitoring and modelling.

Organic micropollutants (OMPs) are widely detected in surface waters. So far, the removal processes of these compounds in situ in river systems are not yet totally revealed. In this study, a combined monitoring and modelling approach was applied to determine the behaviour of 1-H benzotriazole, carbamazepine, diclofenac and galaxolide in a small river system. Sewage treatment plant effluents and the receiving waters of the river Swist were monitored in 9 dry weather sampling campaigns (precipitation < 1 mm on the sampling day itself and <5 mm total precipitation two days before the sampling) during different seasons over a period of 3 years. With the results gained through monitoring, mass balances have been calculated to assess fate in the river. With the DWA Water Quality Model, OMP concentrations in the river were successfully simulated with OMP characteristics gained through literature studies. No removal was determined for 1-H benzotriazole and carbamazepine, whereas diclofenac showed removal that coincided with light intensity. Moreover, modelling based on light sensitivity of diclofenac also suggested relevant degradation at natural light conditions. These two approaches suggest removal by photodegradation. The highest removal in the river was detected for galaxolide, presumably due to volatilisation, sorption and biodegradation. Furthermore, short-term concentration variability in the river was determined, showing that daily concentration patterns are influenced by dynamics of sewage treatment plant effluent volumes and removal processes in the river.