Bio-Polyethylene and Polyethylene Biocomposites: An Alternative toward a Sustainable Future.

Polyethylene (PE), a highly prevalent non-biodegradable polymer in the field of plastics, presents a waste management issue. To alleviate this issue, bio-based PE (bio-PE), derived from renewable resources like corn and sugarcane, offers an environmentally friendly alternative. This review discusses various production methods of bio-PE, including fermentation, gasification, and catalytic conversion of biomass. Interestingly, the bio-PE production volumes and market are expanding due to the growing environmental concerns and regulatory pressures. Additionally, the production of PE and bio-PE biocomposites using agricultural waste as filler materials, highlights the growing demand for sustainable alternatives to conventional plastics. According to previous studies, addition of ≈50% defibrillated corn and abaca fibers into bio-PE matrix and a compatibilizer, results in the highest Young's modulus of 4.61 and 5.81 GPa, respectively. These biocomposites have potential applications in automotive, building construction, and furniture industries. Moreover, the advancement made in abiotic and biotic degradation of PE and PE biocomposites is elucidated to address their environmental impacts. Finally, the paper concludes with insights into the opportunities, challenges, and future perspectives in the sustainable production and utilization of PE and bio-PE biocomposites. In summary, production of PE and bio-PE biocomposites can contribute to a cleaner and sustainable future.

Hydrolytic degradation and biodegradation of polylactic acid electrospun fibers.

Increased use of bioplastics, such as polylactic acid (PLA), helps in reducing greenhouse gas emissions, decreases energy consumption and lowers pollution, but its degradation efficiency has much room for improvement. The degradation rate of electrospun PLA fibers of varying diameters ranging from 0.15 to 1.33 µm is measured during hydrolytic degradation under different pH from 5.5 to 10, and during aerobic biodegradation in seawater supplemented with activated sewage sludge. In hydrolytic conditions, varying PLA fiber diameter had significant influence over percentage weight loss (W%L), where faster degradation was achieved for PLA fibers with smaller diameter. W%L was greatest for PLA-5 > PLA-12 > PLA-16 > PLA-20, with average W%L at 30.7%, 27.8%, 17.2% and 14.3% respectively. While different pH environment does not have a significant influence on PLA degradation, with W%L only slightly higher for basic environments. Similarly biodegradation displayed faster degradation for small diameter fibers with PLA-5 attaining the highest degree of biodegradation at 22.8% after 90 days. Hydrolytic degradation resulted in no significant structural change, while biodegradation resulted in significant hydroxyl end capping products on the PLA surface. Scanning electron microscopy (SEM) imaging of degraded PLA fibers showed a deteriorated morphology of PLA-5 and PLA-12 fibers with increased adhesion structures and irregularly shaped fibers, while a largely unmodified morphology for PLA-16 and PLA-20.

A bioinspired silica nanocomposite for enhanced multidrug-resistant bacteria treatment and wash-free imaging.

Bacterial infections have posed significant threats to public health due to the emergence of antibiotic resistance. In this work, a novel antibacterial composite nanomaterial based on spiky mesoporous silica spheres loaded with poly(ionic liquid)s and aggregation-induced emission luminogens (AIEgens) was designed for efficient multidrug-resistant (MDR) bacteria treatment and imaging. The nanocomposite exhibited excellent and long-term antibacterial activity towards both Gram-negative and Gram-positive bacteria. Meanwhile, fluorescent AIEgens facilitate real-time bacterial imaging. Our study provides a multifunctional platform and a promising alternative to antibiotics for combating pathogenic MDR bacteria.

AFM Manipulation of EGaIn Microdroplets to Generate Controlled, On-Demand Contacts on Molecular Self-Assembled Monolayers.

Liquid metal droplets, such as eutectic gallium-indium (EGaIn), are important in many research areas, such as soft electronics, catalysis, and energy storage. Droplet contact on solid surfaces is typically achieved without control over the applied force and without optimizing the wetting properties in different environments (e.g., in air or liquid), resulting in poorly defined contact areas. In this work, we demonstrate the direct manipulation of EGaIn microdroplets using an atomic force microscope (AFM) to generate repeated, on-demand making and breaking of contact on self-assembled monolayers (SAMs) of alkanethiols. The nanoscale positional control and feedback loop in an AFM allow us to control the contact force at the nanonewton level and, consequently, tune the droplet contact areas at the micrometer length scale in both air and ethanol. When submerged in ethanol, the droplets are highly nonwetting, resulting in hysteresis-free contact forces and minimal adhesion; as a result, we are able to create reproducible geometric contact areas of 0.8-4.5 µm2 with the alkanethiolate SAMs in ethanol. In contrast, there is a larger hysteresis in the contact forces and larger adhesion for the same EGaIn droplet in air, which reduced the control over the contact area (4-12 µm2). We demonstrate the usefulness of the technique and of the gained insights in EGaIn contact mechanics by making well-defined molecular tunneling junctions based on alkanethiolate SAMs with small geometric contact areas of between 4 and 12 µm2 in air, 1 to 2 orders of magnitude smaller than previously achieved.

Quantifying Surface Wetting Properties Using Droplet Probe Atomic Force Microscopy.

The functional properties of a surface, such as its anti-fogging or anti-fouling performance, are influenced by its wettability. To quantify surface wettability, the most common approach is to measure the contact angles of a liquid droplet on the surface. While well established and relatively easy to perform, contact angle measurements were developed to describe macroscopic wetting properties and are difficult to perform for submillimetric droplets. Moreover, they cannot spatially resolve surface heterogeneities that can contribute to surface fouling. To address these shortcomings, we report on using an atomic force microscopy technique to quantitatively measure the interaction forces between a microdroplet and a surface with piconewton force resolution. We show how our technique can be used to spatially map topographical and chemical heterogeneities with micron resolution.

Mapping micrometer-scale wetting properties of superhydrophobic surfaces.

There is a huge interest in developing superrepellent surfaces for antifouling and heat-transfer applications. To characterize the wetting properties of such surfaces, the most common approach is to place a millimetric-sized droplet and measure its contact angles. The adhesion and friction forces can then be inferred indirectly using Furmidge's relation. While easy to implement, contact angle measurements are semiquantitative and cannot resolve wetting variations on a surface. Here, we attach a micrometric-sized droplet to an atomic force microscope cantilever to directly measure adhesion and friction forces with nanonewton force resolutions. We spatially map the micrometer-scale wetting properties of superhydrophobic surfaces and observe the time-resolved pinning-depinning dynamics as the droplet detaches from or moves across the surface.

In Operando Characterization and Control over Intermittent Light Emission from Molecular Tunnel Junctions via Molecular Backbone Rigidity.

In principle, excitation of surface plasmons by molecular tunnel junctions can be controlled at the molecular level. Stable electrical excitation sources of surface plasmons are therefore desirable. Herein, molecular junctions are reported where tunneling charge carriers excite surface plasmons in the gold bottom electrodes via inelastic tunneling and it is shown that the intermittent light emission (blinking) originates from conformational dynamics of the molecules. The blinking rates, in turn, are controlled by changing the rigidity of the molecular backbone. Power spectral density analysis shows that molecular junctions with flexible aliphatic molecules blink, while junctions with rigid aromatic molecules do not.

Directional Excitation of Surface Plasmon Polaritons via Molecular Through-Bond Tunneling across Double-Barrier Tunnel Junctions.

Directional excitation of surface plasmon polaritons (SPPs) by electrical means is important for the integration of plasmonics with molecular electronics or steering signals toward other components. We report electrically driven SPP sources based on quantum mechanical tunneling across molecular double-barrier junctions, where the tunneling pathway is defined by the molecules' chemical structure as well as by their tilt angle with respect to the surface normal. Self-assembled monolayers of S(CH2)nBPh (BPh = biphenyl, n = 1-7) on Au, where the alkyl chain and the BPh units define two distinct tunnel barriers in series, were used to demonstrate and control the geometrical effects. The tilt angle of the BPh unit with respect to the surface normal depends on the value of n, and is 45° when n is even and 23° when n is odd. The tilt angle of the alkyl chain is fixed at 30° and independent of n. For values of n = 1-3, SPPs are directionally launched via directional tunneling through the BPh units. For values of n > 3, tunneling along the alkyl chain dominates the SPP excitation. Molecular level control of directionally launching SPPs is achieved without requiring additional on-chip optical elements, such as antennas, or external elements, such as light sources. Using the molecular tunneling junctions, we provide the first direct experimental demonstration of molecular double-barrier tunneling junctions.

Organic nanoparticles with ultrahigh quantum yield and aggregation-induced emission characteristics for cellular imaging and real-time two-photon lung vasculature imaging.

Fluorescent organic nanoparticles based on small molecules have emerged as an attractive class of fluorescent agents for bioimaging in recent years. Herein, we report orange light-emitting BTPEBD based organic nanoparticles (BTPEBD NPs) with a large Stokes shift (>135 nm), ultrahigh quantum yield (>90% in water) and aggregation-induced emission characteristics. Single nanoparticle analysis studied by wide field microscopy imaging further proves that the BTPEBD NPs exhibit high brightness and good photostability. Both in vitro and in vivo experiments reveal that the BTPEBD NPs are promising fluorescent agents for cellular imaging and real-time two-photon lung vasculature imaging.

Ultrasmall Conjugated Polymer Nanoparticles with High Specificity for Targeted Cancer Cell Imaging.

Fluorescent and biocompatible organic nanoparticles have attracted great interest in cancer detection and imaging, but the nonspecific cellular uptake has limited the detection specificity and sensitivity. Herein, the authors report the ultrasmall conjugated polymer nanoparticles (CPNs) with bright far-red/near-infrared emission for targeted cancer imaging with high specificity. The sizes of the ultrasmall CPNs are around 6 nm (CPN6), while large CPNs show sizes around 30 nm (CPN30). Moreover, CPN6 exhibits largely improved fluorescence quantum yield (η) of 41% than CPN30 (25%). Benefiting from the ultrasmall size, bare CPN6 shows largely suppressed nonspecific cellular uptake as compared to CPN30, while cyclic arginine-glycine-aspartic acid (cRGD) functionalized CPN6 (cRGD-CPN6) possesses excellent selectivity toward αvß3 integrin overexpressed MDA-MB-231 cells over other cells in cell mixtures. The faster body clearance of CPN6 over CPN30 indicates its greater potentials as a noninvasive nanoprobe for in vivo and practical applications.

Protein Nanocage as a pH-Switchable Pickering Emulsifier.

Encapsulation of active compounds in Pickering emulsions using bioderived protein-based stabilizers holds potential for the development of novel formulations in the fields of foods and cosmetics. We employ a dodecahedron hollow protein nanocage as a pH-switchable Pickering emulsifier. E2 protein nanocages are derived from pyruvate dehydrogenase multienzyme complex from Geobacillus stearothermophilus which adsorb at the oil/water interface at neutral and basic pH's and stabilize the Pickering emulsions, while in the acidic range, at pH ∼4, the emulsion separates into emulsion and serum phases due to flocculation. The observed process is reversible for at least five cycles. Optimal formulation of a Pickering emulsion composed of rosemary oil, an essential oil, and water has been achieved by ultrasonication and results in droplets of approximately 300 nm in diameter with an oil/water ratio of 0.11 (v/v) and 0.30-0.35% (wt %). Ionic stabilization is observed for concentrations up to 250 mM NaCl and pH values from 7 to 11. The emulsions are stable for at least 10 days when stored at different temperatures up to 50 °C. The resulting Pickering emulsions of different compositions also form a gel-like structure and show shear thinning behavior under shear stress at a higher oil/water ratio.

Specific Internalisation of Gold Nanoparticles into Engineered Porous Protein Cages via Affinity Binding.

Porous protein cages are supramolecular protein self-assemblies presenting pores that allow the access of surrounding molecules and ions into their core in order to store and transport them in biological environments. Protein cages' pores are attractive channels for the internalisation of inorganic nanoparticles and an alternative for the preparation of hybrid bioinspired nanoparticles. However, strategies based on nanoparticle transport through the pores are largely unexplored, due to the difficulty of tailoring nanoparticles that have diameters commensurate with the pores size and simultaneously displaying specific affinity to the cages' core and low non-specific binding to the cages' outer surface. We evaluated the specific internalisation of single small gold nanoparticles, 3.9 nm in diameter, into porous protein cages via affinity binding. The E2 protein cage derived from the Geobacillus stearothermophilus presents 12 pores, 6 nm in diameter, and an empty core of 13 nm in diameter. We engineered the E2 protein by site-directed mutagenesis with oligohistidine sequences exposing them into the cage's core. Dynamic light scattering and electron microscopy analysis show that the structures of E2 protein cages mutated with bis- or penta-histidine sequences are well conserved. The surface of the gold nanoparticles was passivated with a self-assembled monolayer made of a mixture of short peptidols and thiolated alkane ethylene glycol ligands. Such monolayers are found to provide thin coatings preventing non-specific binding to proteins. Further functionalisation of the peptide coated gold nanoparticles with Ni2+ nitrilotriacetic moieties enabled the specific binding to oligohistidine tagged cages. The internalisation via affinity binding was evaluated by electron microscopy analysis. From the various mutations tested, only the penta-histidine mutated E2 protein cage showed repeatable and stable internalisation. The present work overcomes the limitations of currently available approaches and provides a new route to design tailored and well-controlled hybrid nanoparticles.

Silica shelled and block copolymer encapsulated red-emissive AIE nanoparticles with 50% quantum yield for two-photon excited vascular imaging.

A polymer and silica co-protection strategy has been developed to encapsulate organic fluorogens with aggregation-induced emission and charge transfer characteristics into small nanoparticles (NPs). The co-pretected NPs show bright red fluorescence (50% quantum yield) with a large two-photon action cross-section (450 GM at 840 nm), which have been sucessfully used for two-photon fluorescence imaging of vasculature of the mouse tibial muscle.

A multifunctional probe with aggregation-induced emission characteristics for selective fluorescence imaging and photodynamic killing of bacteria over mammalian cells.

A multifunctional probe aggregation-induced emission-Zinc(II)-dipicolylamine (AIE-ZnDPA) is developed for selective targeting, fluorescence imaging, and photodynamic killing of both Gram-positive and Gram-negative bacteria over mammalian cells. The probe has significant advantages in simple probe design, enhanced fluorescence upon bacteria binding, excellent photostability, and broad-spectrum antibacterial activity with almost no harm to mammalian cells.

Precise and long-term tracking of adipose-derived stem cells and their regenerative capacity via superb bright and stable organic nanodots.

Monitoring and understanding long-term fate and regenerative therapy of administrated stem cells in vivo is of great importance. Herein we report organic nanodots with aggregation-induced emission characteristics (AIE dots) for long-term tracking of adipose-derived stem cells (ADSCs) and their regenerative capacity in living mice. The AIE dots possess high fluorescence (with a high quantum yield of 25±1%), excellent biological and photophysical stabilities, low in vivo toxicity, and superb retention in living ADSCs with negligible interference on their pluripotency and secretome. These AIE dots also exhibit superior in vitro cell tracking capability compared to the most popular commercial cell trackers, PKH26 and Qtracker 655. In vivo quantitative studies with bioluminescence and GFP labeling as the controls reveal that the AIE dots can precisely and quantitatively report the fate of ADSCs and their regenerative capacity for 42 days in an ischemic hind limb bearing mouse model.

Ultrabright organic dots with aggregation-induced emission characteristics for cell tracking.

Noninvasive fluorescence cell tracking provides critical information on the physiological displacement and translocation of actively migrating cells, which deepens our understanding of biomedical engineering, oncological research, stem cell transplantation and therapies. Non-viral fluorescent protein transfection based cell tracing has been widely used but with issues related to cell type-dependent expression, lagged readout, immunogenicity and mutagenesis. Alternative cell tracking methods are therefore desired to attain reliable, stable, and efficient labeling over a long time. In this work, we have successfully developed ultra-bright organic dots with aggregation-induced emission (AIE dots) and demonstrated their capabilities for cellular imaging and cell tracking. The AIE dots possess high fluorescence, super photostability, and excellent cellular retention and biocompatibility. As compared to commonly used pMAX-GFP plasmid labeling approach, the organic AIE dots showed excellent cell labeling on all tested human cell lines and superior tracing performance, which opens up new opportunities in the cell-based immunotherapies and other related biological researches.

Bright quantum-dot-sized single-chain conjugated polyelectrolyte nanoparticles: synthesis, characterization and application for specific extracellular labeling and imaging.

We report a simple method to fabricate quantum-dot-sized nanoparticles (NPs) from poly[9,9-bis((6-N,N,N-trimethylammonium)hexyl)fluorene-alt-co-2,1,3-benzo-xadiazole dibromide] (PFBD). The transmission electron microscope results reveal that the obtained NPs have a mean diameter of ≈4 nm, which is composed of a single PFBD chain. The NPs show bright fluorescence with an emission maximum at ≈636 nm and a quantum yield of ≈26% in water. The fluorescence properties of the NPs are characterized by steady fluorescence microscopy, fluorescence dynamic study and single nanoparticle microscopy, which show superior brightness over commercial quantum dots QD655. The NPs are further conjugated with streptavidin to yield PFBD-SA NPs, which serve as a specific extracellular labeling and imaging probe with high specificity and good photostability.

Stretching and imaging of single DNA chains on a hydrophobic polymer surface made of amphiphilic alternating comb-copolymer.

Functionalization of amine derivatized glass slides with a poly(maleic anhydride)-based comb-copolymer to facilitate stretching, aligning, and imaging of individual dsDNA chains is presented. The polymer-coated surface is hydrophobic due to the presence of the long alkyl side chains along the polymer backbone. The surface is also characterized by low roughness and a globular morphology. Stretched and aligned bacteriophage λ-DNA chains were obtained using a robust method based on stretching by a receding water meniscus at pH 7.8 without the need for small droplet volumes or precoating the surface with additional layers of (bio)molecules. Although the dye to DNA base pairs ratio did not influence substantially the stretching length distributions, a clear peak at stretching lengths close to the contour length of the dsDNA is visible at larger staining ratios.

An intercompartmental enzymatic cascade reaction in channel-equipped polymersome-in-polymersome architectures.

Compartmentalization, as a design principle, is a prerequisite for the functioning of eukaryotic cells. Although cell mimics in the form of single vesicular compartments such as liposomes or polymersomes have been tremendously successful, investigations of the corresponding higher-order architectures, in particular bilayer-based multicompartment vesicles, have only recently gained attention. We hereby demonstrate a multicompartment cell-mimetic nanocontainer, built-up from fully synthetic membranes, which features an inner compartment equipped with a channel protein and a semi-permeable outer compartment that allows passive diffusion of small molecules. The functionality of this multicompartment architecture is demonstrated by a cascade reaction between enzymes that are segregated in separate compartments. The unique architecture of polymersomes, which combines stability with a cell-membrane-mimetic environment, and their assembly into higher-order architectures could serve as a design principle for new generation drug-delivery vehicles, biosensors, and protocell models.