Photon energy dependence of Kerr rotation in GeTe/Sb2Te3 chalcogenide superlattices.

We report on pump-probe based helicity dependent time-resolved Kerr measurements under infrared excitation of chalcogenide superlattices, consisting of alternately stacked GeTe and Sb2Te3 layers. The Kerr rotation signal consists of the specular inverse Faraday effect (SIFE) and the specular optical Kerr effect (SOKE), both of which are found to monotonically increase with decreasing photon energy over a sub-eV energy range. Although the dependence of the SIFE can be attributed to the response function of direct third-order nonlinear susceptibility, the magnitude of the SOKE reflects cascading second-order nonlinear susceptibility resulting from electronic transitions between bulk valence/conduction bands and interface-originating Dirac states of the superlattice.

Terahertz generation measurements of multilayered GeTe-Sb2Te3 phase change materials.

Multilayered structures of GeTe and Sb2Te3 phase change material, also referred to as interfacial phase change memory (iPCM), provide superior performance for nonvolatile electrical memory technology in which the atomically controlled structure plays an important role in memory operation. Here, we report on terahertz (THz) wave generation measurements. Three- and 20-layer iPCM samples were irradiated with a femtosecond laser, and the generated THz radiation was observed. The emitted THz pulse was found to be always p polarized independent of the polarization of the excitation pulse. Based on the polarization dependence as well as the flip of the THz field from photoexcited Sb2Te3 and Bi2Te3, the THz emission process can be attributed to the surge current flow due to the built-in surface depletion layer formed in p-type semiconducting iPCM materials.

Zener Tunneling Breakdown in Phase-Change Materials Revealed by Intense Terahertz Pulses.

We have systematically investigated the spatial and temporal dynamics of crystallization that occur in the phase-change material Ge_{2}Sb_{2}Te_{5} upon irradiation with an intense terahertz (THz) pulse. THz-pump-optical-probe spectroscopy revealed that Zener tunneling induces a nonlinear increase in the conductivity of the crystalline phase. This fact causes the large enhancement of electric field associated with the THz pulses only at the edge of the crystallized area. The electric field concentrating in this area causes a temperature increase via Joule heating, which in turn leads to nanometer-scale crystal growth parallel to the field and the formation of filamentary conductive domains across the sample.

Topological Phase Buried in a Chalcogenide Superlattice Monitored by Helicity-Dependent Kerr Measurement.

Chalcogenide superlattices (SLs), formed by the alternate stacking of GeTe and Sb2Te3 layers, also referred to as interfacial phase-change memory (iPCM), are a leading candidate for spin-based memory device applications. Theoretically, the iPCM structure has been predicted to form a three-dimensional topological insulator or Dirac semimetal phase depending on the constituent layer thicknesses. Here, we experimentally investigate the topological insulating nature of chalcogenide SLs using a helicity-dependent time-resolved Kerr measurement. The helicity-dependent Kerr signal is observed to exhibit a four-cycle oscillation with π/2 periodicity, suggesting the existence of a Dirac-like cone in some chalcogenide SLs. Furthermore, we found that increasing the thickness of the GeTe layer dramatically changed the periodicity, indicating a phase transition from a Dirac semimetal into a trivial insulator. Our results demonstrate that thickness-tuned chalcogenide SLs can play an important role in the manipulation of topological states, which may open up new possibilities for spintronic devices based on chalcogenide SLs.

A cascading nonlinear magneto-optical effect in topological insulators.

Topological insulators (TIs) are characterized by possessing metallic (gapless) surface states and a finite band-gap state in the bulk. As the thickness of a TI layer decreases down to a few nanometers, hybridization between the top and bottom surfaces takes place due to quantum tunneling, consequently at a critical thickness a crossover from a 3D-TI to a 2D insulator occurs. Although such a crossover is generally accessible by scanning tunneling microscopy, or by angle-resolved photoemission spectroscopy, such measurements require clean surfaces. Here, we demonstrate that a cascading nonlinear magneto-optical effect induced via strong spin-orbit coupling can examine such crossovers. The helicity dependence of the time-resolved Kerr rotation exhibits a robust change in periodicity at a critical thickness, from which it is possible to predict the formation of a Dirac cone in a film several quintuple layers thick. This method enables prediction of a Dirac cone using a fundamental nonlinear optical effect that can be applied to a wide range of TIs and related 2D materials.

Significant Volume Expansion as a Precursor to Ablation and Micropattern Formation in Phase Change Material Induced by Intense Terahertz Pulses.

With rapid advances occurring in terahertz (THz) radiation generation techniques, the interaction between matter and intense THz fields has become an important research topic. Among different types of THz radiation sources, the free electron laser (FEL) is a promising experimental tool that is expected to pave the way for new forms of material processing, control of phase transitions, and serve as a test bench for extreme operating conditions in high-speed small-size electrical and magnetic devices through the exploitation of strong THz electrical and magnetic fields without the presence of interband electronic excitation. In the current work, we irradiated Ge2Sb2Te5 phase change memory material with intense THz pulse trains from an FEL and observed THz-induced surface changes due to damage as a precursor to ablation and the formation of fine surface undulations whose spatial period is comparable to or slightly smaller than the wavelength of the excitation THz pulses in the material. The formation of undulations as well as the fact that no significant thermal effect was observed below the volume expansion threshold suggests that THz-induced effects mainly contributed to the observed changes. To the best of our knowledge, this is the first experimental observation of THz-induced undulations (so-called "LIPSS"), which are of potential importance for laser material processing.

Compositional tuning in sputter-grown highly-oriented Bi-Te films and their optical and electronic structures.

Growth of Bi-Te films by helicon-wave magnetron sputtering is systematically explored using alloy targets. The film compositions obtained are found to strongly depend on both the sputtering and antenna-coil powers. The obtainable film compositions range from Bi55Te45 to Bi43Te57 when a Bi2Te3 alloy target is used, and from Bi42Te58 to Bi40Te60 (Bi2Te3) for a Te-rich Bi30Te70 target. All films show strong orientation of the van der Waals layers (00l planes) parallel to the substrate. The atomic level stacking of Bi2Te3 quintuple and Bi bi-layers has been directly observed by high resolution transmission electron microscopy. Band structure simulations reveal that Bi-rich Bi4Te3 bulk is a zero band gap semimetal with a Dirac cone at the Gamma point when spin-orbit coupling is included. Optical measurements also confirm that the material has a zero band gap. The tunability of the composition and the topological insulating properties of the layers will enable the use of these materials for future electronics applications on an industrial scale.

Manipulating the Bulk Band Structure of Artificially Constructed van der Waals Chalcogenide Heterostructures.

The bulk band structures of a variety of artificially constructed van der Waals chalcogenide heterostructures IVTe/V2VI3 (IV: C, Si, Ge, Sn, Pb; V: As, Sb, Bi; VI: S, Se, Te) have been systematically examined using ab initio simulations based on density functional theory. The crystal structure and the electronic band structure of the heterostructures were found to strongly depend on the choice of elements as well as the presence of van der Waals corrections. Furthermore, it was found that the use of the modified Becke-Johnson local density approximation functional demonstrated that a Dirac cone is formed when tensile stress is applied to a GeTe/Sb2Te3 heterostructure, and the band gap can be controlled by tuning the stress. Based on these simulation results, a novel electrical switching device using a chalcogenide heterostructure is proposed.

Pressure-Induced Phase Transitions in GeTe-Rich Ge-Sb-Te Alloys across the Rhombohedral-to-Cubic Transitions.

We demonstrate that pressure-induced amorphization in Ge-Sb-Te alloys across the ferroelectric-paraelectric transition can be represented as a mixture of coherently distorted rhombohedral Ge8Sb2Te11 and randomly distorted cubic Ge4Sb2Te7 and high-temperature Ge8Sb2Te11 phases. While coherent distortion in Ge8Sb2Te11 does not prevent the crystalline state from collapsing into its amorphous counterpart in a similar manner to pure GeTe, the pressure-amorphized Ge8Sb2Te11 phase begins to revert to the crystalline cubic phase at ∼9 GPa in contrast to Ge4Sb2Te7, which remains amorphous under ambient conditions when gradually decompressed from 40 GPa. Moreover, experimentally, it was observed that pressure-induced amorphization in Ge8Sb2Te11 is a temperature-dependent process. Ge8Sb2Te11 transforms into the amorphous phase at ∼27.5 and 25.2 GPa at room temperature and 408 K, respectively, and completely amorphizes at 32 GPa at 408 K, while some crystalline texture could be seen until 38 GPa (the last measurement point) at room temperature. To understand the origins of the temperature dependence of the pressure-induced amorphization process, density functional theory calculations were performed for compositions along the (GeTe)x - (Sb2Te3)1-x tie line under large hydrostatic pressures. The calculated results agreed well with the experimental data.

Resistive switching mechanism of GeTe-Sb2Te3 interfacial phase change memory and topological properties of embedded two-dimensional states.

A theoretical study of an interfacial phase change memory made of a GeTe-Sb2Te3 superlattice with W electrodes is presented to identify the high and low resistance states and the switching mechanism. The ferro structure of the GeTe layer block in the Te-Ge-Te-Ge sequence can be in the low resistance state only if the SET/RESET mode consists of a two step dynamical process, corresponding to a vertical flip of the Ge layer with respect to the Te layer, followed by lateral motion driven by thermal relaxation. The importance of spin-orbit coupling at the GeTe/Sb2Te3 interface to the "bias polarity-dependent" SET/RESET operation is shown, and an analysis of the two-dimensional states confined at the GeTe/Sb2Te3 interface inside the resistive switching layer is presented. Our results allow us to propose a phase diagram for the transition from a topologically nontrivial to a trivial gap state of these two-dimensional compounds.

Atomic Reconfiguration of van der Waals Gaps as the Key to Switching in GeTe/Sb2Te3 Superlattices.

Nonvolatile memory, of which phase-change memory (PCM) is a leading technology, is currently a key element of various electronics and portable systems. An important step in the development of conceptually new devices is the class of van der Waals (vdW)-bonded GeTe/Sb2Te3 superlattices (SLs). With their order of magnitude faster switching rates and lower energy consumption compared to those of alloy-based devices, they are widely regarded as the next step in the implementation of PCM. In contrast to conventional PCM, where the SET and RESET states arise from the crystalline and amorphous phases, in SLs, both the SET and RESET states remain crystalline. In an earlier work, the superior performance of SLs was attributed to the reduction of entropic losses associated with the one-dimensional motion of interfacial Ge atoms located in the vicinity of Sb2Te3 quintuple layers. Subsequent experimental studies using transmission electron microscopy revealed that GeTe and Sb2Te3 blocks strongly intermix during the growth of the GeTe phase, challenging the original proposal but at the same time raising new fundamental issues. In this work, we propose a new approach to switching in SLs associated with the reconfiguration of vdW gaps accompanied by local deviation of stoichiometry from the GeTe/Sb2Te3 quasibinary alloys. The model resolves in a natural way the existing controversies, explains the large conductivity contrast between the SET and RESET crystalline states, is not compromised by Ge/Sb intermixing, and provides a new perspective for the industrial development of memory devices based on such SLs. The proposed concept of vdW gap reconfiguration may also be applicable to designing a broad variety of engineered two-dimensional vdW solids.

THz Pulse Detection by Multilayered GeTe/Sb2Te3.

We proposed and demonstrated terahertz (THz) pulse detection by means of multilayered GeTe/Sb2Te3 phase-change memory materials that are also known as a multilayer topological insulator-normal insulator (MTN) system. THz time-domain spectroscopy measurement was performed for MTN films with different multilayer repetitions as well as a conventional as-grown Ge-Te-Sb (GST) alloy film. It was found that MTNs absorb THz waves and that the absorption coefficient depends on the number of layers, while the as-grown GST alloy film was almost transparent for THz waves. Simple MTN-based THz detection devices were fabricated, and the THz-induced change in the current signal was measured when a DC bias voltage was applied between the electrodes. We confirmed that irradiation of THz pulse causes a decrease in the resistance of the MTNs. This result indicates that our devices are capable of THz detection.

Morphology and Electric Conductance Change Induced by Voltage Pulse Excitation in (GeTe)2/Sb2Te3 Superlattices.

Chalcogenide superlattice (SL) phase-change memory materials are leading candidates for non-volatile, energy-efficient electric memory where the electric conductance switching is caused by the atom repositioning in the constituent layers. Here, we study the time evolution of the electric conductance in [(GeTe)2/(Sb2Te3)1]4 SLs upon the application of an external pulsed electric field by analysing the structural and electrical responses of the SL films with scanning probe microscopy (SPM) and scanning probe lithography (SPL). At a low pulse voltage (1.6-2.3 V), a conductance switching delay of a few seconds was observed in some SL areas, where the switch to the high conductance state (HCS) is accompanied with an SL expansion under the strong electric field of the SPM probe. At a high pulse voltage (2.5-3.0 V), the HCS current was unstable and decayed in a few seconds; this is ascribed to the degradation of the HCS crystal phase under excessive heating. The reversible conductance change under a pulse voltage of opposite polarity emphasised the role of the electric field in the phase-transition mechanism.

Sub-nanometre resolution of atomic motion during electronic excitation in phase-change materials.

Phase-change materials based on Ge-Sb-Te alloys are widely used in industrial applications such as nonvolatile memories, but reaction pathways for crystalline-to-amorphous phase-change on picosecond timescales remain unknown. Femtosecond laser excitation and an ultrashort x-ray probe is used to show the temporal separation of electronic and thermal effects in a long-lived (>100 ps) transient metastable state of Ge2Sb2Te5 with muted interatomic interaction induced by a weakening of resonant bonding. Due to a specific electronic state, the lattice undergoes a reversible nondestructive modification over a nanoscale region, remaining cold for 4 ps. An independent time-resolved x-ray absorption fine structure experiment confirms the existence of an intermediate state with disordered bonds. This newly unveiled effect allows the utilization of non-thermal ultra-fast pathways enabling artificial manipulation of the switching process, ultimately leading to a redefined speed limit, and improved energy efficiency and reliability of phase-change memory technologies.

Anisotropic lattice response induced by a linearly-polarized femtosecond optical pulse excitation in interfacial phase change memory material.

Optical excitation of matter with linearly-polarized femtosecond pulses creates a transient non-equilibrium lattice displacement along a certain direction. Here, the pump and probe pulse polarization dependence of the photo-induced ultrafast lattice dynamics in (GeTe)2/(Sb2Te3)4 interfacial phase change memory material is investigated under obliquely incident conditions. Drastic pump polarization dependence of the coherent phonon amplitude is observed when the probe polarization angle is parallel to the c-axis of the sample, while the pump polarization dependence is negligible when the probe polarization angle is perpendicular to the c-axis. The enhancement of phonon oscillation amplitude due to pump polarization rotation for a specific probe polarization angle is only found in the early time stage (≤2 ps). These results indicate that the origin of the pump and probe polarization dependence is dominantly attributable to the anisotropically-formed photo-excited carriers which cause the directional lattice dynamics.

Coherent gigahertz phonons in Ge2Sb2Te5 phase-change materials.

Using ≈40 fs ultrashort laser pulses, we investigate the picosecond acoustic response from a prototypical phase change material, thin Ge2Sb2Te5 (GST) films with various thicknesses. After excitation with a 1.53 eV-energy pulse with a fluence of ≈5 mJ cm(-2), the time-resolved reflectivity change exhibits transient electronic response, followed by a combination of exponential-like strain and coherent acoustic phonons in the gigahertz (GHz) frequency range. The time-domain shape of the coherent acoustic pulse is well reproduced by the use of the strain model by Thomsen et al 1986 (Phys. Rev. B 34 4129). We found that the decay rate (the inverse of the relaxation time) of the acoustic phonon both in the amorphous and in the crystalline phases decreases as the film thickness increases. The thickness dependence of the acoustic phonon decay is well modeled based on both phonon-defect scattering and acoustic phonon attenuation at the GST/Si interface, and it is revealed that those scattering and attenuation are larger in crystalline GST films than those in amorphous GST films.

Femtosecond structural transformation of phase-change materials far from equilibrium monitored by coherent phonons.

Multicomponent chalcogenides, such as quasi-binary GeTe-Sb2Te3 alloys, are widely used in optical data storage media in the form of rewritable optical discs. Ge2Sb2Te5 (GST) in particular has proven to be one of the best-performing materials, whose reliability allows more than 10(6) write-erase cycles. Despite these industrial applications, the fundamental kinetics of rapid phase change in GST remain controversial, and active debate continues over the ultimate speed limit. Here we explore ultrafast structural transformation in a photoexcited GST superlattice, where GeTe and Sb2Te3 are spatially separated, using coherent phonon spectroscopy with pump-pump-probe sequences. By analysing the coherent phonon spectra in different time regions, complex structural dynamics upon excitation are observed in the GST superlattice (but not in GST alloys), which can be described as the mixing of Ge sites from two different coordination environments. Our results suggest the possible applicability of GST superlattices for ultrafast switching devices.

Giant multiferroic effects in topological GeTe-Sb2Te3 superlattices.

Multiferroics, materials in which both magnetic and electric fields can induce each other, resulting in a magnetoelectric response, have been attracting increasing attention, although the induced magnetic susceptibility and dielectric constant are usually small and have typically been reported for low temperatures. The magnetoelectric response usually depends on d-electrons of transition metals. Here we report that in [(GeTe)2(Sb2Te3) l ] m superlattice films (where l and m are integers) with topological phase transition, strong magnetoelectric response may be induced at temperatures above room temperature when the external fields are applied normal to the film surface. By ab initio computer simulations, it is revealed that the multiferroic properties are induced due to the breaking of spatial inversion symmetry when the p-electrons of Ge atoms change their bonding geometry from octahedral to tetrahedral. Finally, we demonstrate the existence in such structures of spin memory, which paves the way for a future hybrid device combining nonvolatile phase-change memory and magnetic spin memory.

Mirror-symmetric magneto-optical Kerr rotation using visible light in [(GeTe)2(Sb2Te3)1]n topological superlattices.

Interfacial phase change memory (iPCM), that has a structure of a superlattice made of alternating atomically thin GeTe and Sb2Te3 layers, has recently attracted attention not only due to its superior performance compared to the alloy of the same average composition in terms of energy consumption but also due to its strong response to an external magnetic field (giant magnetoresistance) that has been speculated to arise from switching between topological insulator (RESET) and normal insulator (SET) phases. Here we report magneto-optical Kerr rotation loops in the visible range, that have mirror symmetric resonances with respect to the magnetic field polarity at temperatures above 380 K when the material is in the SET phase that has Kramers-pairs in spin-split bands. We further found that this threshold temperature may be controlled if the sample was cooled in a magnetic field. The observed results open new possibilities for use of iPCM beyond phase-change memory applications.

Use of UV-vis-NIR spectroscopy to monitor label-free interaction between molecular recognition elements and erythropoietin on a gold-coated polycarbonate platform.

Label-free-based detection is pivotal for real-time monitoring of biomolecular interactions and to eliminate the need for labeling with tags that can occupy important binding sites of biomolecules. One simplest form of label-free-based detection is ultraviolet-visible-near-infrared (UV-vis-NIR) spectroscopy, which measure changes in reflectivity as a means to monitor immobilization and interaction of biomolecules with their corresponding partners. In biosensor development, the platform used for the biomolecular interaction should be suitable for different molecular recognition elements. In this study, gold (Au)-coated polycarbonate was used as a platform and as a proof-of-concept, erythropoietin (EPO), a doping substance widely abused by the athletes was used as the target. The interaction of EPO with its corresponding molecular recognition elements (anti-EPO monoclonal antibody and anti-EPO DNA aptamer) is monitored by UV-vis-NIR spectroscopy. Prior to this, to show that UV-vis-NIR spectroscopy is a suitable method for measuring biomolecular interaction, the interaction between biotin and streptavidin was demonstrated via this strategy and reflectivity of this interaction decreased by 25%. Subsequent to this, interaction of the EPO with anti-EPO monoclonal antibody and anti-EPO DNA aptamer resulted in the decrease of reflectivity by 5% and 10%, respectively. The results indicated that Au-coated polycarbonate could be an ideal biosensor platform for monitoring biomolecular interactions using UV-vis-NIR spectroscopy. A smaller version of the Au-coated polycarbonate substrates can be derived from the recent set-up, to be applied towards detecting EPO abuse among atheletes.