Potential of using medicinal plant extracts as photosensitizers for antimicrobial photodynamic therapy.

Antimicrobial photodynamic therapy (APDT) is a promising approach to overcome antimicrobial resistance. However, for widespread implementation of this approach, approved photosensitizers are needed. In this study, we used commercially available preparations (Calendulae officinalis floridis extract, Chamomillae recutitae floridis extract, Achillea millefolii herbae extract; Hypericum perforatum extract; Eucalyptus viminalis folia extract) as photosensitizers for inactivation of gram-negative (Pseudomonas aeruginosa) and gram-positive (Staphylococcus aureus) bacteria. Spectral-luminescent analysis has shown that the major chromophores are of chlorophyll (mainly chlorophyll a and b) and hypericin nature. The extracts are efficient generators of singlet oxygen with quantum yield (Î³Δ ) from 0.40 to 0.64 (reference compound, methylene blue with Î³Δ = 0.52). In APDT assays, bacteria before irradiation were incubated with extracts for 30 min. After irradiation and 24 h of incubation, colony-forming units (CFU) were counted. Upon exposure of P. aeruginosa to radiation of 405 nm, 590 nm, and 660 nm at equal energy dose of 30 J/cm2 (irradiance - 100 mW/cm2 , exposure time - 5 min), the most pronounced effect is observed with blue light (>3 log10 reduction); in case of S. aureus, the effect is approximately equivalent for light of indicated wavelengths and dose (>4 log10 reduction).

Design and Realization of Polymeric Waveguide/Microring Structures for Telecommunication Domain.

Polymer-based micro-optical components are very important for applications in optical communication. In this study, we theoretically investigated the coupling of polymeric waveguide and microring structures and experimentally demonstrated an efficient fabrication method to realize these structures on demand. First, the structures were designed and simulated using the FDTD method. The optical mode and loss in the coupling structures were calculated, thereby giving the optimal distance for optical mode coupling between two rib waveguide structures or for optical mode coupling in a microring resonance structure. Simulations results then guided us in the fabrication of the desired ring resonance microstructures using a robust and flexible direct laser writing technique. The entire optical system was thus designed and manufactured on a flat base plate so that it could be easily integrated in optical circuits.

Effects of Supplemental Light Spectra on the Composition, Production and Antimicrobial Activity of Ocimum basilicum L. Essential Oil.

This study was performed to investigate the effects of different supplemental light spectra and doses (duration and illuminance) on the essential oil of basil (Ocimum basilicum L.) cultivated in the net-house in Vietnam during four months. Ten samples of basil aerial parts were hydrodistilled to obtain essential oils which had the average yields from 0.88 to 1.30% (v/w, dry). The oils analyzed using GC-FID and GC-MS showed that the main component was methyl chavicol (87.4−90.6%) with the highest values found in the oils of basil under lighting conditions of 6 h/day and 150−200 µmol·m−2·s−1. Additional lighting conditions caused the significant differences (p < 0.001) in basil biomass and oil production with the highest values found in the oils of basil under two conditions of (1) 71% Red: 20% Blue: 9.0% UVA in at 120 µmol·m−2·s−1 in 6 h/day and (2) 43.5% Red: 43.5% Blue: 8.0% Green: 5.0% Far-Red at 100 µmol·m−2·s−1 in 6 h/day. The oils of basil in some formulas showed weak inhibitory effects on only the Bacillus subtilis strain. Different light spectra affect the biomass and essential oil production of basil, as well as the concentrations of the major components in the oil.

Rapid direct laser writing of desired plasmonic nanostructures.

We demonstrate a direct way to realize arbitrary gold nanostructures via a local dewetting method. This technique was based on the optically induced local thermal effect at the focusing region of a direct laser writing (DLW) system employing a green continuous-wave laser. The local high temperature allowed the creation of gold nano-islands only at the focusing area of the optical system. By moving the focusing spot, this DLW method allowed us to "write" desired two-dimensional gold patterns with a feature size down to sub-lambda. A heat model was also proposed to theoretically explain the localized heating process of the absorbing gold layer. The preliminary results were demonstrated for data storage and color printer applications.

Direct Laser Writing of Magneto-Photonic Sub-Microstructures for Prospective Applications in Biomedical Engineering.

We report on the fabrication of desired magneto-photonic devices by a low one-photon absorption (LOPA) direct laser writing (DLW) technique on a photocurable nanocomposite consisting of magnetite ( Fe 3 O 4 ) nanoparticles and a commercial SU-8 photoresist. The magnetic nanocomposite was synthesized by mixing Fe 3 O 4 nanoparticles with different kinds of SU-8 photoresists. We demonstrated that the degree of dispersion of Fe 3 O 4 nanoparticles in the nanocomposite depended on the concentration of Fe 3 O 4 nanoparticles, the viscosity of SU-8 resist, and the mixing time. By tuning these parameters, the most homogeneous magnetic nanocomposite was obtained with a concentration of about 2 wt % of Fe 3 O 4 nanoparticles in SU-8 2005 photoresist for the mixing time of 20 days. The LOPA-based DLW technique was employed to fabricate on demand various magneto-photonic submicrometer structures, which are similar to those obtained without Fe 3 O 4 nanoparticles. The magneto-photonic 2D and 3D structures with sizes as small as 150 nm were created. We demonstrated the strong magnetic field responses of the magneto-photonic nanostructures and their use as micro-actuators when immersed in a liquid solution.