Comparison of the Accuracy and Efficiency of Two Dynamic Navigation System Workflow for Fiber-Post Removal: Small versus Large Field-of-View Registration Workflows.

INTRODUCTION: This study investigates the feasibility of a dynamic navigation system (DNS) small field of view workflow (DNS-SFOVw) for fiber-post removal and compares its accuracy and efficiency to the conventional large field of view workflow (DNS-LFOVw). METHODS: Fifty-six extracted human maxillary molars were divided into DNS-SFOVw (n=28) and DNS-LFOVw (n=28). The palatal canal was restored with an intra-radicular RelyX fiber post and luted with RelyX Unicem; a core buildup was used. Teeth were mounted in a 3D-printed surgical jaw. A preoperative cone-beam-computed tomography (CBCT) scan was taken with a 40 x 40 mm FOV for the DNS-SFOVw and a single arch CBCT scan for the DNS-LFOVw. The drilling entry point, trajectory, angle, and depth were planned in the X-guide software. The DNS registration method for the DNS-SFOVw was virtual-based registration on teeth, and the marker point-based method was used for the DNS-LFOVw. The fiber posts were drilled out under DNS guidance. A postoperative CBCT scan was taken. Three-dimensional (3D) deviations, angular deflection, number of mishaps, registration, and total operation time were calculated. RESULTS: The DNS-SFOVw was as accurate as DNS-LFOVw (p>.05). The DNS-LFOVw registration time was less than DNS-SFOVw (p<.05). There was no difference in the number of mishaps (p>.05). Both DNS-SFOVw and DNS-LFOVw were time-efficient, with DNS-LFOVw taking less total operational time (p<.05). CONCLUSION: Within the limitations of this in-vitro study, the DNS-SFOVw was as accurate as the DNS-LFOVw for fiber-post removal. Both DNS-LFOVw and DNS-SFOVw were time-efficient in removing fiber-posts.

Treatment of retrograde peri-implantitis originating from apical periodontitis of an adjacent tooth: A clinical case letter.

This report aims to present a treatment of retrograde peri-implantitis originating from apical periodontitis of an adjacent tooth in an 84-year-old male. Apical periodontitis of the maxillary left central incisor (#9) extended to the apex of the maxillary left lateral incisor implant (#10), which had been functioning for 16 years. Root canal treatment for #9 was performed, followed by root end surgery to treat the apical periodontitis, which showed a periapical radiolucency measured 1 cm in its greatest dimension. After the root end filling was placed, neither bone substitute materials nor barrier membranes were used to fill and cover the bony defect area. A 2- year postoperative radiograph confirmed the osseous healing around the apices of #9 and #10.

Real-Time Three-dimensional Dynamic Navigation for Post Space Preparation in Root Canal-Treated Teeth: An In vitro Study.

INTRODUCTION: The aim of this study was to investigate the feasibility of a real-time three-dimensional dynamic navigation system (3D-DNS) for post space preparation (PSP) in root canal-treated teeth and to compare the accuracy and efficiency of 3D-DNS to freehand (FH) for PSP. METHODS: Fifty-four maxillary molars were divided into two groups: 3D-DNS (n = 27) and FH group (n = 27). Cone beam computed tomography (CBCT) scans were taken preoperatively and postoperatively. The drilling path for the PSP was virtually planned in the preoperative CBCT scan in the X-guide software (X-Nav Technologies, Lansdale, PA). For the 3D-DNS group, the PSP drilling was conducted under dynamic navigation. The 3D deviations and angular deflections were calculated. The residual dentin thickness (RDT) was determined after PSP. The operation time and the total number of mishaps were recorded. Shapiro-Wilk, t-test or Mann-Whitney rank sum, weighted Cohen's kappa, and Fisher exact tests were used (P < .05). RESULTS: The PSP was completed in all samples (54/54). The 3D-DNS was more accurate than the FH, with significantly fewer 3D deviations and angular deflections (all, P < .05). The 3D-DNS required less operating time than the FH (P < .05). For the 3D-DNS, no teeth had RDT < 1 mm, whereas 6/27 in the FH showed RDT < 1 mm after the PSP. There was no difference in the total number of mishaps (P > .05). CONCLUSION: Within the limitations of this in vitro study, the 3D-DNS is feasible for PSP. The 3D-DNS improved the accuracy and efficiency of PSP. The dynamic navigation system can potentially become a safe and reliable technology for PSP.

Comparison of the Efficacy and Safety of Pulp Sensitivity Testing Results Using a New Pulp Testing Device versus Some Commonly Used Methods: A Crossover Study.

INTRODUCTION: The efficacy and safety of a single novel electronic pulp sensitivity tester with a transilluminator (PSTT) capable of providing 4 different tests was compared with gold standard (GS) pulp testing methods. METHODS: Four hundred eighty teeth, including 3 from each quadrant and their contralateral and opposing teeth, were randomly assessed using the PSTT or GS methods. Seven days later, the same teeth were assessed using the method not used earlier so that all teeth were evaluated using both methods. Sixty previously root canal-treated teeth, serving as negative controls, were assessed identically to the experimental groups. Results were analyzed using IBM SPSS software (IBM Corp, Armonk, NY) (P < .05). RESULTS: A higher percentage of teeth responded to cold and electricity using GS methods compared with the PSTT (99.4 vs 93.1 and 99.6 vs 97.3, respectively). A lower percentage of teeth responded to heat using the GS method compared with the PSTT (50.0 vs 68.1). Chi-square tests determined differences in the proportion of sensitivity to temperature, and electric testing methods were statistically significant (P < .001 and P = .004, respectively). No difference in the proportion of sensitivity was observed for transillumination. The Wilcoxon signed rank test determined significantly shorter cold testing times using the GS method (P = .024). Shorter testing times were observed using the PSTT for heat (P < .001), electric pulp testing (P = .048), and transillumination (P = .001). The overall PSTT testing time was significantly shorter than the GS testing time (P = .03). Tissue injury was not observed. CONCLUSIONS: The PSTT efficiently and safely provided heat and transillumination for pulpal diagnosis. Improvements are needed to enhance the cold and electric stimulus efficacy.

Piezoelectric Device and Dynamic Navigation System Integration for Bone Window-Guided Surgery.

INTRODUCTION: This study investigates the feasibility of integrating a piezoelectric device (PIEZO) into a dynamic navigation system (DNS) for bone-window guided surgery. It compares the accuracy and efficiency of PIEZO + DNS to PIEZO + Freehand (FH) procedure for bone-window cutting and root-end resection (RER). METHODS: Forty-eight mandibular molars of 3D-printed surgical jaw models were divided into two groups: PIEZO + DNS (n = 24) and PIEZO + FH (n = 24). Cone-beam computed tomography scans were taken before and after the procedure. The procedure was virtually planned on X-guide software. The bone-window cutting and RER were conducted with a PIEZO under dynamic navigation in the PIEZO + DNS group and using the dental operating microscope in the PIEZO + FH group. The 2D- and 3D-accuracy deviations and angular deflection were measured for the bone window cut. The root length resected and resection angle were calculated. The bone window cut, RER, total operating time, and number of mishaps were recorded. RESULTS: PIEZO + DNS was more accurate than PIEZO + FH for bone-window cutting, showing fewer 2D and 3D deviations and less angular deflection (P < .05). The resection angle was lower in the PIEZO + DNS (P < .05). The bone-window cut and total operating time were significantly reduced using a DNS (P < .05). There was no difference in the number of mishaps (P > .05). CONCLUSIONS: Within the limitations of this in vitro study, the integration of a PIEZO into a DNS is feasible for bone-window guided surgery. The DNS improved the accuracy and efficiency of bone-window cutting.

Augmented Reality and 3-Dimensional Dynamic Navigation System Integration for Osteotomy and Root-end Resection.

INTRODUCTION: Augmented reality (AR) superimposes high-definition computer-generated virtual content onto the existing environment, providing users with an enhanced perception of reality. This study investigates the feasibility of integrating an AR head-mounted device into a 3-dimensional dynamic navigation system (3D-DNS) for osteotomy and root-end resection (RER). It compares the accuracy and efficiency of AR + 3D-DNS to 3D-DNS for osteotomy and RER. METHODS: Seventy-two tooth roots of 3D-printed surgical jaw models were divided into two groups: AR + 3D-DNS (n = 36) and 3D-DNS (n = 36). Cone-beam computed tomography scans were taken pre and postoperatively. The osteotomy and RER were virtually planned on X-guide software and delivered under 3D-DNS guidance. For the AR + 3D-DNS group, an AR head-mounted device (Microsoft HoloLens 2) was integrated into the 3D-DNS. The 2D- and 3D-deviations were calculated. The osteotomy and RER time and the number of procedural mishaps were recorded. RESULTS: Osteotomy and RER were completed in all samples (72/72). AR + 3D-DNS was more accurate than 3D-DNS, showing lower 2D- and 3D-deviation values (P < .05). The AR + 3D-DNS was more efficient in time than 3D-DNS (P < .05). There was no significant difference in the number of mishaps (P > .05). CONCLUSIONS: Within the limitations of this in vitro study, the integration of an AR head-mounted device to 3D-DNS is feasible for osteotomy and RER. AR improved the accuracy and time efficiency of 3D-DNS in osteotomy and RER. Head-mounted AR has the potential to be safely and reliably integrated into 3D-DNS for endodontic microsurgery.

A Cadaver-based Comparison of Sleeve-guided Implant-drill and Dynamic Navigation Osteotomy and Root-end Resections.

INTRODUCTION: This study compared the accuracy and efficiency of fully guided static and dynamic computer-assisted surgical navigation techniques for osteotomy and root-end resection (RER). METHODS: Fifty roots from cadaver heads were divided into two groups: fully guided static computer-assisted endodontic microsurgery (FG sCAEMS) and dynamic computer-assisted endodontic microsurgery (dCAEMS) (all, n = 25). Cone-beam computed tomography scans were taken pre and postoperatively. The osteotomy and RER were planned virtually in the preoperative cone-beam computed tomography scan and guided using 3D-printed surgical guides in the FG sCAEMS and 3D-dynamic navigation system in the dCAEMS. The 2D and 3D deviations and angular deflection were calculated. The osteotomy volume, resected root length, and resection angle were measured. The osteotomy and RER time and the number of procedural mishaps were recorded. RESULTS: FG sCAEMS was as accurate as dCAEMS, with no difference in the 2D and 3D deviation values or angular deflection (P > .05). The osteotomy and RER time were shortened using FG sCAEMS (P < .05). The FG sCAEMS showed a greater number of incomplete RERs than dCAEMS. Osteotomy volume, RER angle, and root length resected were similar in both groups (P > .05). FG sCAEMS and dCAEMS were feasible for osteotomy and RER. CONCLUSIONS: Within the limitations of this cadaver-based study, FG sCAEMS was as accurate as dCAEMS. Both FG sCAEMS and dCAEMS were time-efficient for osteotomy and RER.

Comparison of a Novel Static Computer-aided Surgical and Freehand Techniques for Osteotomy and Root-end Resection.

INTRODUCTION: This study compared the accuracy and efficiency of a novel static computer-aided surgical technique using a 3-dimensional (3D)-printed surgical guide (3D-SG) with a fully guided drill protocol (3D-SG FG) to the freehand (FH) osteotomy and root-end resection (RER). METHODS: Forty-six roots from 2 cadaver heads were divided into 2 groups: 3D-SG FG (n = 23) and FH (n = 23). Cone-beam computed tomographic scans were taken preoperatively and postoperatively. The endodontic microsurgery was planned in Blue Sky Bio software, and the 3D-SG was designed and 3D printed. The osteotomy and RER were conducted using a guided twist drill diameter of 2 mm and an ascending tapered drill with diameters of 2.8/3.2, 3.2/3.6, 3.8/4.2, and 4.2 mm with respective guided drill guides. Two-dimensional and three-dimensional virtual deviations and angular deflection were calculated. Linear osteotomy measures and root resection angle were obtained. The osteotomy and RER time and the number of mishaps were recorded. RESULTS: Two-dimensional and three-dimensional accuracy deviations and angular deflection were lower in the 3D-SG FG protocol than in the FH technique (P < .05). The height, length, and depth of the osteotomy and root resection angle were less in the 3D-SG FG protocol than in the FH technique (P < .05). The osteotomy and RER time with the 3D-SG FG protocol were less than the FH method (P < .05). CONCLUSIONS: Within the limitations of this cadaver-based study using denuded maxillary and mandibular jaws, 3D-SG FG protocol showed higher accuracy than FH osteotomy and RER. Moreover, the 3D-SG FG drill protocol significantly reduced the surgical time.

Comparison of the Accuracy and Efficiency of a 3-Dimensional Dynamic Navigation System for Osteotomy and Root-end Resection Performed by Novice and Experienced Endodontists.

INTRODUCTION: The aim of the study is to investigate whether the 3-dimensional dynamic navigation system (3D-DNS) can improve experienced endodontists' (EEs') and novice endodontists' (NEs') accuracy and efficiency in osteotomy and root-end resection (RER) and to verify that the 3D-DNS enables NEs to perform osteotomy and RER as accurately and efficiently as EEs. METHODS: Seventy-six roots in cadaver heads were randomly divided into 4 groups: 3D-DNS-NE, 3D-DNS-EE, freehanded (FH)-NE, and FH-EE (all, n = 19). Cone-beam computed tomography scans were taken preoperatively and postoperatively. Osteotomy and RER were planned virtually in the X-guided software (X-Nav Technologies, Lansdale). Accuracy was calculated by measuring the 2-dimensional and 3D virtual deviations and angular deflection using superimposing software (X-Nav technologies). Efficiency was determined by the time of operation and the number of mishaps. RESULTS: Accuracy deviations were significantly fewer in the 3D-DNS-EE group than those in the FH-EE group (P < .05). We found less 2-dimensional and 3D accuracy deviations comparing the 3D-DNS-NE group to the FH-NE group (P < .05). The time required for osteotomy and RER with the 3D-DNS was ∼ ½ of that required for the FH method for both EEs and NEs (P < .05). We found no difference in the number of mishaps between the 3D-DNS and FH groups for EEs and NEs (P > .05). CONCLUSIONS: The 3D-DNS improved EEs' and NEs' accuracy and efficiency in osteotomy and RER. The NEs were as efficient as the EEs using the 3D-DNS. Notably, the 3D-DNS improved the NEs' accuracy compared to the FH method, but the 3D-DNS did not enable the NEs to perform osteotomy and RER as accurately as the EEs.

Real-time 3-dimensional Dynamic Navigation System in Endodontic Microsurgery: A Cadaver Study.

INTRODUCTION: This study evaluated the accuracy and efficiency of the 3-dimensional dynamic navigation system (3D-DNS) to perform minimally invasive osteotomy (MIO) and root end resection (RER) in endodontic microsurgery (EMS) and investigated the viability of root end cavity preparation (RECP) and root end fill (REF) in MIO. METHODS: Forty-eight tooth roots were divided in cadaver heads into 2 groups: 3D-DNS (n = 24) and freehand (n = 24). Cone-beam computed tomographic scans were taken before and after surgery. First, virtual 3D-DNS accuracy was verified using 3 outcome measures: 2-dimensional and 3-dimensional virtual deviations and angular deflection. Second, the accuracy of 3D-DNS for performing MIO was investigated in 2 outcome measures: osteotomy size and volume. Third, the 3D-DNS accuracy was determined for RER in 3 outcomes: resected root length, root length after resection, and resection angle. The viability of RECP and REF was investigated and REF depth and volume measured as well, and procedural time and the number of mishaps were recorded. RESULTS: Two- and 3-dimensional virtual deviations and the angular deflection were lower in the 3D-DNS group than the freehand group (P < .05). Osteotomy height, length, and volume were all reduced when using 3D-DNS (P < .05). The resection angle was lower for 3D-DNS (P < .05). RECP and REF were completed in 100% of the roots. The REF depth achieved was ∼3 mm. Osteotomy time, RER time, and the total procedure time were all significantly shortened using 3D-DNS (P < .05). CONCLUSIONS: 3D-DNS enabled our surgeon to perform accurate and efficient EMS with minimally invasive osteotomy and RER. The surgeon was also able to conduct RECP with adequate REF in minimally invasive osteotomy performed using 3D-DNS guidance.

Efficacy of GentleWave System and Passive Ultrasonic Irrigation with Minimally Invasive and Conventional Instrumentation Technique against Enterococcus faecalis Lipoteichoic Acid in Infected Root Canals.

INTRODUCTION: This study evaluated the effectiveness of the GentleWave System (GWS; Sonendo, Laguna Hills, CA) and passive ultrasonic irrigation (PUI) in removing Enterococcus faecalis lipoteichoic acid (LTA) from infected root canals with a minimally invasive technique (MIT) and the conventional instrumentation technique (CIT). METHODS: Sixty extracted human maxillary first premolars were included. All teeth were dentin pretreated and inoculated with LTA prepared from E. faecalis. First, 12 teeth were cryogenically ground to investigate the viability of recovering intraradicular E. faecalis LTA. Afterward, 48 teeth were randomly divided into the following groups: GWS + MIT, GWS + CIT, PUI + MIT, and GWS + CIT (all n = 12). Teeth were instrumented with a Vortex Blue (Dentsply Sirona, Ballaigues, Switzerland) rotary file size 15/.04 for MIT and 35/.04 for CIT. Samples were collected before and after a root canal procedure with sterile/apyrogenic paper points and after cryogenically ground for intraradicular LTA analysis. LTA was quantified with an LTA enzyme-linked immunosorbent assay kit. RESULTS: E. faecalis LTA was recovered from 100% of the samples (48/48) before the root canal procedure. GWS + MIT and GWS + CIT were the most effective protocols against E. faecalis LTA, with no difference between them (P > .05). PUI + CIT was more effective than PUI + MIT (P < .05) but less effective than GWS + MIT and GWS + CIT (P < .05). The GWS groups showed more root canals with undetected E. faecalis LTA after treatment than all groups tested. CONCLUSIONS: GWS + MIT and GWS + CIT were the most effective protocols against E. faecalis LTA in infected root canals.

Comparison of GentleWave system and passive ultrasonic irrigation with minimally invasive and conventional instrumentation against LPS in infected root canals.

This study compared the effectiveness of GentleWave system (GWS) and passive ultrasonic irrigation (PUI) in removing lipopolysaccharides (LPS) from infected root canals after minimally invasive (MIT) and conventional instrumentation (CIT) techniques. Sixty first premolars with two roots were inoculated with fluorescent LPS conjugate (Alexa Fluor 594). Of those, twelve were dentin pretreated, inoculated with fluorescent LPS conjugate, and submitted to confocal laser scanning microscopy (CLSM) to validate the LPS-infection model. Forty-eight teeth were randomly divided into treatment groups: GWS + MIT, GWS + CIT, PUI + MIT, and PUI + CIT (all, n = 12). Teeth were instrumented with Vortex Blue rotary file size 15/0.04 for MIT and 35/0.04 for CIT. Samples were collected before (s1) and after a root canal procedure (s2) and after cryogenically ground the teeth (s3) for intraradicular LPS analysis. LPS were quantified with LAL assay (KQCL test). GWS + MIT and GWS + CIT were the most effective protocols against LPS, with no difference between them (p > 0.05). PUI + CIT was more effective than PUI + MIT (p < 0.05) but less effective than GWS + MIT and GWS + CIT. GWS was the most effective protocol against LPS in infected root canals using MIT and CIT techniques.

Positively Charged Polyvinylidene Fluoride Membrane: A Potential Alternative for Absorbent Paper Points in Endodontics.

INTRODUCTION: This study compared the absorbency capacity of paper points (PPs) with positively charged and noncharged polyvinylidene fluoride membranes (PVDFMs) and investigated the ability of PPs and PVDFMs to bind and remove endotoxin. METHODS: Three commercially available PPs were compared with PVDFM (Millipore Sigma, Burlington, MA) prototype points. We recorded the initial dry weight for each PP and PVDFM using a digital balance to ±0.0001 precision for absorbency. PPs and PVDFMs were then immersed in deionized water and weighed to obtain the wet weight. The absorbency was calculated with the following formula: percent increase = ([wet weight - dry weight]/dry weight) × 100. For endotoxin removal, we first quantified endotoxin remaining in wells after immersing PPs and PVDFMs in a 24-well plate containing 10 endotoxin units/mL Escherichia coli O55:B5 (Lonza, Walkersville, MD). We then extracted and quantified endotoxin from PPs and PVDFMs. Endotoxin was quantified using the Kinetic-QCL test (Lonza). RESULTS: The absorbencies for the positively charged and noncharged PVDFMs were higher than the PPs (P < .05), with no difference between them (P > .05). The positively charged PVDFMs removed more endotoxin than the noncharged PVDFMs and the PPs (P < .05). Moreover, the noncharged PVDFMs bound and removed more endotoxin than any PPs (P < .05). CONCLUSIONS: PVDFM prototype points are more absorbent than PPs. Moreover, the positively charged PVDFM points are more effective in binding and removing endotoxin than noncharged PVDFMs and PPs. This study suggests that positively charged PVDFMs with a 0.22-µm pore size could potentially replace PPs used in endodontics.

Accuracy and Efficiency of 3-dimensional Dynamic Navigation System for Removal of Fiber Post from Root Canal-Treated Teeth.

INTRODUCTION: The purpose of this study was to investigate the accuracy and efficiency of the 3-dimensional dynamic navigation system (DNS) compared with the freehand technique (FH) when removing fiber posts from root canal-treated teeth. METHODS: Twenty-six maxillary teeth were included. Teeth were root canal treated and restored with Parapost Taper Lux (Coltene/Whaledent, Altstätten, Switzerland) luted with RelyX Unicem (3M ESPE, St Paul, MN). A core buildup was then performed using Paracore (Coltene/Whaledent). Teeth were mounted in tissue-denuded cadaver maxillae. Teeth were divided into 2 groups: the DNS group (n = 13) and the FH group (n = 13). Cone-beam computed tomographic scans were taken pre- and postoperatively. The drilling path and depth were planned virtually using X-guide software (X-Nav Technologies, Lansdale, PA) in both groups. For the DNS group, drilling was guided with X-Nav software and the FH group under a dental operating microscope. Global coronal and apical deviations, angular deflection, operation time, and the number of mishaps were compared between the groups to determine the accuracy and efficiency. The 3-dimensional volume (mm3) of all teeth was calculated before and after post removal using the Mimics Innovation Suite (Materialise NV, Leuven, Belgium). The Shapiro-Wilk, 1-way analysis of variance, and Fisher exact tests were used (P < .05). RESULTS: The DNS group showed significantly less global coronal and apical deviations and angular deflection than the FH group (P < .05). DNS required less operation time than FH. Moreover, the DNS technique had significantly less volumetric loss of tooth structure than the FH technique (P < .05). CONCLUSIONS: The DNS was more accurate and efficient in removing fiber posts from root canal-treated teeth than the FH technique.

Aerosols Generated during Endodontic Treatment: A Special Concern during the Coronavirus Disease 2019 Pandemic.

INTRODUCTION: The aims of this study were to investigate aerosolized microorganisms generated during endodontic emergencies and nonsurgical root canal therapy (NSRCT), to assess the spread of airborne microbes, and to verify the spatial distribution of airborne microbial spread. METHODS: A total of 45 endodontic procedures were sampled, including full pulpotomy (n = 15), pulpectomy (n = 15), and NSRCT (n = 15). Samples were collected during room resting and after treatment. The passive air sampling technique using settle plates was applied. Agar plates were set at different locations in the operatory. The colony-forming unit (CFU) was counted in brain-heart infusion blood agar plates. A set of agar plates containing selective chromogenic culture media was used for the isolation and presumptive identification of target microorganisms. Fungi were investigated using Sabouraud dextrose agar. RESULTS: Pulpotomy generated the lowest mean CFU count (P < .05). There was no difference between the mean CFU counts found in pulpectomy and NSRCT (P > .05). A higher mean CFU count was found close to the patient's mouth (0.5 m) than at a 2-m distance in pulpectomy and NSRCT (P < .05). There was no difference between the mean CFU count found in front of the patient's mouth versus diagonal in pulpectomy and NSRCT (P > .05). Staphylococcus aureus (22/45, 48.8%) was the most frequent bacteria species. Longer treatment times were associated with higher CFU counts. CONCLUSIONS: Our findings indicated that pulpotomy generates less aerosolized microorganisms than pulpectomy and NSRCT. The proximity to the patient's mouth and the treatment duration were implicated in the level of contamination.

Dental Abscess to Septic Shock: A Case Report and Literature Review.

Sepsis is a leading cause of death in the United States, with a mortality rate in excess of 215,000 deaths per year. It may lead to septic shock, a complex pathophysiological process with microbial and host response events that progress to multisystem derangement. There is poor documentation of the relationship between dental infection and septic shock, with only a few case reports of septic shock secondary to dentoalveolar abscess. Presented is a case of sepsis/septic shock in a 23-year-old man with signs and symptoms of pulpal necrosis, acute apical abscess, and canine space infection that rapidly progressed to an altered mental state, hyperthermia, tachycardia, hypotension, acute respiratory failure, diarrhea, renal insufficiency, lactic acidosis, leukocytosis, and hyperglycemia. Once septic shock develops, the mortality rate is nearly 50%. Early antimicrobial intervention is associated with surviving severe sepsis, making it critical for dentists to understand local factors leading to the crisis and the signs and symptoms of the sepsis-septic shock continuum.

Accuracy and Efficiency of a Dynamic Navigation System for Locating Calcified Canals.

INTRODUCTION: Calcified canals present a challenge during endodontic treatments. The purpose of this study was to compare the accuracy and efficiency of a dynamic navigation system (DNS) to the freehand (FH) method for locating calcified canals in human teeth. METHODS: Sixty human single-rooted teeth with canal obliteration were selected and mounted in dry cadaver jaws. Based on cone-beam computed tomographic scans of the jaws, the drilling path and depth were virtually planned to use X-Guide software (X-Nav Technologies, LLC, Lansdale, PA). Access preparation was made with navigation in the DNS group and without guidance in the FH group by 2 operators with different levels of experience. Postoperative cone-beam computed tomographic scans were taken of all teeth. Linear and angular deviations and reduced dentin thickness at 2 levels were measured. The time for locating the canal, the number of mishaps, and the unsuccessful attempts were determined and analyzed. RESULTS: The mean linear and angular deviations, reduced dentin thickness (at both levels), the time for access cavity preparation, and the number of mishaps in the DNS group were significantly less than the FH group (P ≤ .05). The unsuccessful attempts were not different between the 2 groups (P > .05). The time for access preparation was significantly shorter for the board-certified endodontist in the FH group (P ≤ .05). CONCLUSIONS: The DNS was more accurate and more efficient than the FH technique in locating calcified canals in human teeth. This novel DNS can help clinicians avoid catastrophic mishaps during access preparation in calcified teeth.

Opioid-prescribing Habits of Practitioner and Educator Members of the American Association of Endodontists: Report of a National Survey.

Dentists and physicians alike often prescribe opioids for dental pain management. The purpose of this study was to identify the common practices among United States endodontists for prescribing opioids to their patients. A descriptive, cross-sectional survey was developed to query 1000 American Association of Endodontists members from all 7 districts in the United States. The 20-question survey addressed provider demographics, types and frequency of medications prescribed, and clinical scenarios that compelled prescription-writing habits. The anonymous survey was electronically mailed. There was a preference to prescribe nonsteroidal anti-inflammatory drugs and/or acetaminophen followed by hydrocodone to manage endodontic pain. The majority of respondents limited an opioid prescription to ≤4 days. Different demographics played a role in the response to direct questions if they ever felt or succumbed to pressure toward prescribing opioids. Opioids are the second most prescribed medication to manage endodontic postoperative pain. Practice background was a significant factor in feeling pressure to prescribe an opioid.

What every dentist should know about antibiotic-resistant bacteria.

The emergence of antibiotic-resistant bacteria has complicated patient treatment and yielded poorer outcomes. This article provides an overview for dental professionals of the challenges posed by resistant microbial strains and the research efforts to overcome this significant obstacle.

A Modified Resin Sealer: Physical and Antibacterial Properties.

INTRODUCTION: The purpose of this study was to investigate the physical and antibacterial properties of a resin sealer mixed with a quaternary ammonium compound, dimethylaminododecyl methacrylate (DMAHDM) and nanosilver (NAg). METHODS: A pilot study was completed to determine the highest concentrations of DMAHDM and NAg that did not significantly alter the physical properties (setting time, flow, solubility, and dimensional change) of AH Plus (Dentsply Sirona, York, PA) when added to the sealer. These concentrations were selected to create a modified resin sealer (mAH Plus). A modified direct contact test evaluated antibacterial properties of AH Plus, DMAHDM + AH Plus, NAg + AH Plus, and mAH Plus at days 1, 7, and 14 against Enterococcus faecalis. RESULTS: Concentrations of 2.5% DMAHDM and 0.15% NAg were added to AH Plus. The flow of mAH Plus was significantly decreased but still within American National Standards Institute/American Dental Association specifications. There were no significant differences in setting time, solubility, or dimensional change. On day 1, 0.15% NAg + AH Plus, 2.5% DMAHDM + AH Plus, and mAH Plus were significantly more effective against E. faecalis compared with AH Plus (P < .05). On days 7 through 14, 2.5% DMAHDM + AH Plus and mAH Plus continued to be significantly more antibacterial than AH Plus (P < .05). CONCLUSIONS: The addition of 0.15% NAg and 2.5% DMAHDM did not adversely affect the physical properties of AH Plus, and mAH Plus was significantly more antibacterial against E. faecalis.